HL-2A装置送气和加料的脱靶特性

HL-2A装置辐射偏滤器实验采用边缘补充送气和分子束加料等方法来提高主等离子体密度,降低边缘等离子体温度、增加辐射功率分额,获得脱靶等离子体。偏滤器室内进行主动补充送气或者注入惰性气体杂质,降低偏滤器等离子体温度,获得脱靶等离子体,并首次获得了超声分子束注入产生脱靶等离子体的实验结果。利用HL-2A装置偏滤器同一极向截面内外中性化板上安装的嵌入式探针阵列和偏滤器室安装的电动探针系统,测量了偏滤器靶板上和偏滤器室的等离子体参数及其分布,并进行了相关分析和改善约束以及偏滤器脱靶等离子体运行模式下等离子体行为的研究。     

Impurity behaviours of HL-2A divertor tokamak during the initial operation period

The divertor configuration was successfully formed and the siliconization as a wall conditioning was first achieved on HL-2A tokamak experimentally in 2004. The divertor configuration is reconstructed by the use of the CFC code. Impurity as an important issue is investigated in the experiments with divertor configuration and wall conditioning. Impurities dramatically decrease after both the divertor configuration is formed and silicon is coated on the surface of the vacuum vessel.     

Observation of chaotic ELMs in HL-2A tokamak

The high confinement mode(H-mode) operation is recently obtained in HL-2A divertor configuration,the corresponding edge localized mode(ELM) is recognized as being of type III.Time intervals in ELM time series are analysed to obtain the information about the ELM process.Signatures of unstable periodic orbits(UPOs) are detected,which are indicators of chaos and may be used to control the big ELM events.     

Study of impurity behaviour in non-coronal equilibrium state

A physical model of analysing the behaviour of impurities out of coronal equilibrium in tokamak plasmas has been proposed. Through solving the time-dependent rate equations including the effects of atomic processes and the particle transport losses, the ionization state distribution is obtained for a range of low Z impurities such as helium, carbon, oxygen and argon. By using the ionization state distribution of these impurities, the radiation rate coefficients and the mean charge state changing with plasma temperature are calculated. The results show that the mean charge state （Z） is sensitively dependent on the parameter neT, and this is the reason why the radiation power of impurities under non-coronal equilibrium conditions is several orders of magnitude higher than that under coronal equilibrium condition.[第一段]     

�п���˵����������ѵĻ����Ԥ���о�

HL-2A和HL-1M装置采用了激光吹气注入高Z杂质来缓减大破裂中的等离子体电流衰竭,并给出了初步实验结果。在HL-2A装置上建立了利用MHD扰动的参量预报放电破裂先兆的报警系统,研制了MHD实时检测与处理系统,实现了放电破裂先兆的预报、快速触发激光吹气、形成阻性高辐射等离子体、消耗热能和磁能,缓减大破裂。实验证明,这是一种使得大型聚变实验装置在放电破裂之前显著减少等离子体中热能和磁能,而且能安全终止放电的简单、快速和有效的途径。     

Preliminary analysis of impurity transport in HL-2A ohmic discharges

This paper describes the behaviour of impurity transport in HL-2A ohmic discharges. In 2005, small quantities of metallic impurities （A1, Ni and Ti） were successfully injected into HL-2A plasmas by laser blow-off technique, and their progression was followed by the soft x-ray cameras with good spatial and temporal resolutions. The impurity confinement time is estimated from the characteristic decay time of the soft x-ray signal of the injected impurities, and it is about 30-60 ms. The transport coefficients of impurities （including diffusion coefficient and convection velocity） in radial different region have been derived by using a one-dimenslonal impurity transport code, the results present that diffusion coefficient is much smaller in the central region of plasmas than the outside of it, and it is much larger than that of neoclassical theory predictions; namely, it is anomalous.[第一段]     

Investigation of impurity transport using supersonic molecular beam injected neon in HL-2A ECRH plasma

In this paper, we describe the behavior of impurity transport in the HL-2A electron cyclotron resonance heating （ECRH） L-mode plasma. The neon as a trace impurity is injected by the supersonic molecular beam injection （SMBI） technique, which is used for the first time to study the impurity transport in HL-2A. The progression of neon ions is monitored by the soft X-ray camera and bolometer arrays with good temporal and spatial resolutions. The convection and diffusion process of the neon ions are investigated with the one-dimensional impurity transport code STRAHL. The results show that the diffusion coefficient D of neon ions is a factor of four larger than the neoclassical value in the central region. The value of D is larger in the outer region of the plasma （ρ 〉 0.6） than in the central region of the plasma （ρ 〈 0.6）. The convective velocity directs inwards with a value of ～-1.0 m/s in the Ohmic discharge, but it reverses to direct outwards with a value of ～ 8.0 m/s in the outer region of the plasma when ECRH is applied. The result indicates that the impurity transport is strongly enhanced with ECRH.     

HL-2A���������ܶȷ�������ϵͳ����

介绍了HL-2A等离子体密度反馈控制系统的设计和实现。从密度反馈控制系统的设计原理、硬件设计和软件设计几方面,论述了等离子体密度反馈系统在HL-2A装置上的实现。实验证明,该系统实现了维持稳定可靠的密度波形的要求。     

HL-2A װ���и���������������ģ���ȶ����о�

结合HL-2A 装置的参数,在电子回旋共振加热(ECRH)离(在)轴加热的情况下,研究高能量捕获电子驱动的鱼骨模不稳定性。数值结果表明,高能量电子极向比压βh 大于某一个比压阈值βh,crit 时,鱼骨模会被高能量电子激发,其频率随高能量电子极向比压的增大而缓慢增加且与高能量电子的环向进动频率一致;比压阈值βh,crit 随着高能量电子密度剖面峰化程度的增加而减小,但当密度剖面增大到一定值时比压阈值βh,crit 趋近于一个常数。此外,还分析了箍缩角和扰动能对鱼骨模实频和增长率的影响。发现在箍缩角α0 =1附近增长率有一极小值,表明高能量勉强通行电子对鱼骨模具有稳定作用;而扰动能 δWˆc增大时,鱼骨模表现出实频变大而增长率变小的特征,这表明了本底等离子体对鱼骨模有一定的稳定效果。     

HL-2A托卡马克送气成像研究

送气成像(gas puff imaging，GPI)是一种重要的研究边缘辐射诊断手段.分析了送气(gas puffing，GP)的原子分子过程，指出气体辐射的主要成分是Hα线，出现在边缘区域，并给出其强度和位置的表达式.介绍HL-2A托卡马克上GPI成像系统的改进和实验布置.从成像的角度获得了GP实验中氢气在等离子体空间的辐射图形，观察结果证实上述分析.在放电开始阶段，氢原子可以穿越待建立的完全等离子体区并形成长条形的辐射亮区.一般的GP加料中，CCD图片与控制信号，以及其他诊断结果相符合.在等离子体边缘区域强场侧(HFS)和弱场侧(LFS)都观察到很强的Hα线辐射. 关键词： 送气 CCD成像 Hα线     

HL-2A装置偏滤器的脱靶等离子体实验

在HL-2A装置偏滤器靶板上采用嵌入式静电三探针阵列和偏滤器室内的电动扫描四探针组测量了同一极向截面的内外中性化板上和偏滤器室内的电子温度、密度、悬浮电位、空间电位、电场、电子压强及其分布,研究了偏滤器中等离子体参数的分布及非对称性和脱靶等离子体运行模式下的等离子体行为,开展了偏滤器脱离靶板等离子体的实验研究。利用主真空室的快速往复扫描三台阶式六探针系统测量了主等离子体边缘和偏滤器室内的等离子体温度、密度、粒子通量和中性粒子密度等参数,研究了脱靶等离子体的形成过程、物理特性、控制方法,以及对主等离子体性能的影响。     

HL-2A 装置中高能量捕获电子鱼骨模不稳定性研究

结合HL-2A 装置的参数,在电子回旋共振加热(ECRH)离(在)轴加热的情况下,研究高能量捕获电子驱动的鱼骨模不稳定性。数值结果表明,高能量电子极向比压β_h 大于某一个比压阈值β_h,crit 时,鱼骨模会被高能量电子激发,其频率随高能量电子极向比压的增大而缓慢增加且与高能量电子的环向进动频率一致;比压阈值β_h,crit 随着高能量电子密度剖面峰化程度的增加而减小,但当密度剖面增大到一定值时比压阈值β_h,crit 趋近于一个常数。此外,还分析了箍缩角和扰动能对鱼骨模实频和增长率的影响。发现在箍缩角α₀ =1附近增长率有一极小值,表明高能量勉强通行电子对鱼骨模具有稳定作用;而扰动能 δWˆ_c增大时,鱼骨模表现出实频变大而增长率变小的特征,这表明了本底等离子体对鱼骨模有一定的稳定效果。     

用激光吹气注入高Z杂质使HL-1M托卡马克放电安全终止的研究

采用高Z杂质注入HL-1M等离子体中, 触发等离子体电流衰竭的实验已经施行.用激光吹气注入高Z杂质能够增加辐射冷却，等离子体在-3ms时间内迅速冷却而且在电流终止之前电子温度损失约80%.实验证明：它是一种使得大型聚变实验装置上在放电破裂之前显著减少等离子体中热能而且安全终止放电的简单、快速和有效的途径. 关键词： 高Z杂质 破裂 等离子体终止 激光吹气     

HL-2A真空紫外光谱空间分布测量及绝对标定

A vacuum ultraviolet VUV spectrometer with spatial and temporal resolutions was presented in this paper. The sensitivity of the spectrometer has been calibrated in situ by using the VUV bremsstrahlung continuum radiation of the HL-2A plasma. The sensitivity coefficients of two gratings were given. The absolute density profile of carbon radiation was thus obtained based on the absolutely radial profile measurement of carbon radiation.     

HL-2A托卡马克超声分子束注入深度和加料效果研究

超声分子束注入深度与加料效率是分子束加料研究中的基本课题.在近期开展的超声分子束注入实验中，发现分子束注入深度与等离子体电子温度和密度、分子束源的气压和温度有直接关系，获得了分子束注入深度的定标律.在低温气体源(液氮冷却)的分子束注入实验中，发现分子束流中形成了团簇，其注入深度超过30 cm，分析了在低温气源分子束注入实验中的团簇现象. 关键词： 超声分子束注入 注入深度 加料效率 团簇     

Investigation of impurity transport using laser blow-off technique in the HL-2A Ohmic and ECRH plasmas

Impurity transports in two neighboring discharges with and without electron cyclotron resonance heating(ECRH)are studied in the HL-2A tokamak by laser blow-off(LBO) technique.The progression of aluminium ions as the trace impurity is monitored by soft x-ray(SXR) and bolometer detector arrays with good temporal and spatial resolutions.Obvious difference in the time trace of the signal between the Ohmic and ECRH L-mode discharges is observed.Based on the numerical simulation with one-dimensional(1D) impurity transport code STRAHL,the radial profiles of impurity diffusion coefficient D and convective velocity V are obtained for each shot.The result shows that the diffusion coefficient D significantly increases throughout the plasma minor radius for the ECRH case with respect to the Ohmic case,and that the convection velocity V changes from negative(inward) for the Ohmic case to partially positive(outward) for the ECRH case.The result on HL-2A confirms the pump out effect of ECRH on impurity profile as reported on various other devices.     

HL-2A装置电子密度多道干涉测量实验系统

电子密度是核聚变等离子体研究中的一个主要物理参数,为获取电子密度时空分布的准确信息,结合HL-2A装置结构特点设计并建立了八道FIR激光干涉仪测量系统。在长光路的布局中采用了介质波导传输,研制了长谐振腔高功率HCN波导激光器。另外为减少干扰影响在差拍信号数据采集电子学中采用了数字锁相滤波FPGA技术, 并用软件和硬件两种相位比较方法监测电子密度,实现了密度随时间变化的实时显示。在等离子体放电中干涉仪系统测量精度可达1/33条纹,相应密度约为1.3×10¹¹cm^-3,时间分辨为0.1ms。     

Simulations of the effects of density and temperature profile on SMBI penetration depth based on the HL-2A tokamak configuration

Using the trans-neut module of the BOUT++ code, we study how the fueling penetration depth of supersonic molecular beam injection(SMBI) is affected by plasma density and temperature profiles. The plasma densities and temperatures in L-mode are initialized to be a set of linear profiles with different core plasma densities and temperatures. The plasma profiles are relaxed to a set of steady states with different core plasma densities or temperatures. For a fixed gradient, the steady profiles are characterized by the core plasma density and temperature. The SMBI is investigated based on the final steady profiles with different core plasma densities or temperatures. The simulated results suggest that the SMB injection will be blocked by dense core plasma and high-temperature plasma. Once the core plasma density is set to be N_(i0)= 1.4N_0(N_0= 1 × 10~(19)m~(-3)) it produces a deeper penetration depth. When N_(i0) is increased from 1.4N_0 to 3.9N_0 at intervals of 0.8N_0, keeping a constant core temperature of T_(e0)= 725 eV at the radial position of ψ = 0.65, the penetration depth gradually decreases. Meanwhile, when the density is fixed at N_(i0)= 1.4N_0 and the core plasma temperature T_(e0) is set to 365 eV,the penetration depth increases. The penetration depth decreases as T_(e0) is increased from 365 eV to 2759 eV. Sufficiently large N_(i0) or T_(e0) causes most of the injected molecules to stay in the scrape-off-layer(SOL) region, lowering the fueling efficiency.     

HL-2M 装置运行控制技术初步研究

重点介绍了 HL-2M 装置的运行技术和初步的等离子体控制实验结果,包括等离子体放电方案设计、 线圈电流控制、击穿阶段零场匹配和等离子体电流以及位移的控制。为了降低放电运行风险,HL-2M 装置初始放 电采用了简化的放电方案,通过整定 PID 参数实现了线圈电流控制,在击穿阶段获得了 10V 以上的环电压和较大 范围的零场区域,成功实现等离子体击穿。最后,投入了等离子体电流和水平位移反馈控制算法,成功将等离子 体放电脉宽提升至 200ms 以上,且维持 I_p≥100kA 的时间超过了 100ms,上述结果表明 HL-2M 装置运行控制技术 得到了初步的检验。      

Density of impurity states of shallow donors in a quantum well under intense laser field

The density of donor impurity states in a square GaAs–AlGaAs quantum well under an intense laser field is calculated taking into account the laser dressing effects on both the Coulomb potential and the confining potential. Using the effective-mass approximation within a variational scheme, the donor binding energy is obtained as a function of the laser dressing parameter, and the impurity position. Our results point out that a proper consideration of the density of impurity states may be of relevance in the interpretation of the optical phenomena related to shallow impurities in quantum wells, where the effects of an intense laser field compete with the quantum confinement.