Z箍缩动态黑腔形成过程MULTI程序一维数值模拟

Z箍缩动态黑腔能够高效地将Z箍缩丝阵等离子体动能转换为黑腔辐射能,为驱动惯性约束靶丸聚变提供高品质的X射线辐射场.利用一维双温多群辐射磁流体力学程序MULTI-IFE,研究了"聚龙一号"装置驱动电流条件下的Z箍缩动态黑腔形成基本物理过程.数值模拟结果表明,在动态黑腔形成过程中,辐射热波的传播速度比冲击波的传播速度更快,比冲击波更早到达泡沫中心,使中心区域的泡沫在冲击波到达前就已具有较高的辐射温度.对于"聚龙一号"装置动态黑腔实验0180发次采用的负载参数,辐射热波和冲击波在泡沫中的传播速度分别约为36.1 cm/μs和17.6 cm/μs,黑腔辐射温度在黑腔形成初期约80 eV,在冲击波到达泡沫中心前可达100 eV以上,丝阵等离子体外表面发射的X射线能量集中在1000 eV以下.本文给出了程序采用的计算模型、美国"土星"装置丝阵内爆计算结果和"聚龙一号"装置动态黑腔实验0180发次模拟结果.     

Flashboard plasma characterization using spectroscopy

The plasma produced by a 10 cm×6 cm planar flashboard has been investigated by emission spectroscopy. The plasma composition, density, and temperature have been determined with time and space resolution using measurement of the relative intensity of spontaneous emission in different atomic and ionic transitions together with calculations based on a collisional-radiative equilibrium model. The (1-2)×10¹³ cm^-3 and (3-4) eV plasma flows away from the flashboard surface at a speed of about 10 cm/μs. A 1.7 cm/μs transverse velocity has been obtained from the Doppler width of an emission line     

Solitary electromagnetic pulses detected with super-Alfvénic flows in Earth's geomagnetic tail

Solitary nonlinear (deltaB/B>1) electromagnetic pulses have been detected in Earth's geomagnetic tail accompanying plasmas flowing at super-Alfvénic speeds. The pulses in the current sheet had durations of approximately 5 s, were left-hand circularly polarized, and had phase speeds of approximately the Alfvén speed in the plasma frame. These pulses were associated with a field-aligned current J(parallel) and observed in low density (approximately 0.3 cm(-3)), high temperature (T(e) approximately T(i) approximately 3x10(7) K), and beta approximately 10 plasma that included electron and ion beams streaming along B. The wave activity was enhanced from below the ion cyclotron frequency to electron cyclotron and upper hybrid frequencies. The detailed properties suggest the pulses are nonlinearly steepened ion cyclotron or Alfvén waves.     

Numerical analysis of nitrogen-mixed argon plasma characteristicsand injected particle behavior in an ICP torch for ultrafine powdersynthesis

A numerical model is presented for the analysis of plasma characteristics of an ICP torch and gas mixing effects on the plasma when a nitrogen gas is added into the argon plasma as a carrier or sheath gas at the torch inlet, The fluid equations describing the plasma flow and temperature fields and the diffusions between two different gases are solved along with a magnetic vector potential equation for electromagnetic fields. The trajectory and the temperature change with time for a particle injected into the plasma are also investigated by a plasma-particle interaction model to find out optimum injection conditions for the synthesis of ultrafine nitride ceramic powders, It is found from the calculations that the nitrogen-mixed argon plasma with a nitrogen sheath gas is more favorable than the plasma with a nitrogen carrier gas for the reaction kinetics of nitride synthesis. It is also found that the radial injection through the holes of the tube wall Is preferable to the axial injection at the torch inlet for the complete evaporation of injected particle and the effective chemical reaction of reactant vapor with nitrogen. For the radial injection in an ICP torch of 20 cm in axial length, the optimum injection locations and initial velocities of 50 μm aluminum particles are found for synthesizing aluminum nitride are in the range of 6~12 cm apart from the torch inlet and over 15 m/s, respectively     

Scaling microsecond-conduction-time plasma opening switch operationfrom 2 to 5 MA

We describe experiments in which conduction currents were successfully scaled from 2 to 5 MA for conduction times around 1 μs in a coaxial geometry plasma opening switch (POS) on the 4 MJ ACE 4 driver. Simple models of POS operation, derived from previous work, were used to scale successful results from drivers that operate at microsecond conduction times, but at currents below 1 MA. An MHD model for the conduction phase was verified in which the square root of the plasma density is approximately proportional to the product of conduction time and peak conduction current divided by the switch radius and length. For the opening phase, a model where the POS gap is approximately constant when the local plasma conditions at the beginning of the conduction phase are kept roughly the same is consistent with the observed POS opening voltages of at least 1 MV. The conduction current was increased by increasing the POS cathode radius from 6 to 20 cm while maintaining roughly the same plasma density. This increase in radius resulted in the observed increase in the conduction-current/conduction-time product from 2 to 5 MA μs while maintaining MV POS voltages     

二极管爆炸发射阴极等离子体的膨胀扩展

分析了二极管中爆炸发射产生阴极等离子体的演化特征,在考虑了阴极等离子体朝阳极膨胀运动使二极管阴阳极间距缩短这一效应的同时,还计入了阴极等离子体沿发射表面径向扩展运动对二极管有效发射面积的影响。基于Child-Langmuir定律,利用在一个四脉冲强流电子束源装置上得到的电流、电压等实验数据,假定阴极等离子体轴向膨胀和径向扩展速度近似相等,研究了阴极等离子体的膨胀扩展动力学行为。计算结果表明,阴极等离子体朝阳极的膨胀和沿径向的扩展速度为0.9～2.8 cm/s。     

Influence of interrupted current amplitude on the post-arc currentand gap recovery after current zero-experiment and simulation

For commercial vacuum circuit interrupter valves with radial field contact, the post-arc current (PAC) waveform was measured after short circuit current interruption applying a transient recovery voltage (TRV) of about 15 kV/s (RRRV). Keeping the current decline di/dt at current zero constant, the power frequency (PF) current amplitude Iˆ_PF was varied from 0.5 up to two times of the rated short circuit current. Significant influence of Iˆ_PF on the gaps memory is shown in particular effecting the post-arc current duration which varies in a range between 2 and 8 μs. Based on the existing physical models an interpretation of the results is given. It is shown that the memory effect influences the gap recovery time. The experimental results were further used to determine the parameters of the sheath growth model described by Andrews and Varey (1971). The initial ion density is fitted according to the current ramp di/dt before current zero (CZ) and according to the measured Q_PF=∫i _PF×dt during the arcing phase. The results of two different test procedures were applied in order to separate the effect of current ramp di/dt and Q_PF=∫i_PF×dt. The influence of both parameters and of the rate of rise of the recovery voltage du/dt (RRRV) on the sheath edge velocity could be demonstrated by simulation     

Dynamics of mass transport and magnetic fields in low-wire-number-array Z pinches

The dynamics of mass transport were observed in a wire array implosion with multiframe laser probing. Plasma bubbles arise at breaks in the wires. Interferometry shows that the leading edge of the bubbles brings material to the axis of the array. The speed of this material was measured to be > or =3 x 10(7) cm/s during the wire array implosion. A shock was observed during the collision of the bubbles with the precursor. The Faraday effect indicates current flowing in breaks on the wires. The current switches from the imploding mass to the on-axis plasma column at the beginning of the x-ray pulse.     

Effect of Cathode and Anode Voltage on an Ion Sheath Thickness in a Magnetically Confined Diffusion Plasma

This article reports about the ion sheath thickness variation occurring in front of a negatively biased plate immersed in the target plasma region of a double plasma device. The target plasma is produced due to the local ionization of neutral gas by the high energetic electrons coming from the source region (main discharge region). It is observed that for an increase in cathode voltage (filament bias voltage) in the source region, the ion flux into the plate increases. As a result, the sheath at the plate contracts. Again, for an increase in source anode voltage (magnetic cage bias), the ion flux to the plate decreases. As a result, the sheath expands at the plate. The ion sheath formed at the separation grid of the device is found to expand for an increase in cathode voltage and it contracts for an increase in the anode voltage of the main discharge region. One important observation is that the applied anode bias can control the Bohm speed of the ions towards the separation grid. Furthermore, it is observed that the ion current collected by the separation grid is independent of changes in plasma density in the diffusion region but is highly dependent on the source plasma parameters. (© 2008 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

532nm连续激光晶化非晶硅薄膜的原位拉曼光谱研究

用磁控溅射制备了非晶硅薄膜,用波长为532 nm的连续激光退火和显微Raman光谱原位测试技术和场发射扫描电子显微镜研究了非晶硅薄膜在不同激光功率密度和不同扫描速度下的晶化状态。结果表明,激光照射时间10 s,激光功率密度大于2.929×105W/cm2时,能实现非晶硅薄膜晶化。在激光功率密度为5.093×105W/cm2,扫描速度为10 mm/s时非晶硅开始向多晶硅转化。在5.093×105W/cm2的功率密度下,以1.0 mm/s的扫描速度退火非晶硅薄膜,得到的晶粒直径为740 nm。     

Dynamics of the ionizing and magnetic fronts in the radialcompression stage of a DPF current sheath

Further results regarding the sudden drop of dense plasma focus (DPF) neutron yield at low pressure are presented. Experimental measurements of temporal evolution of magnetic piston MP (interface plasma-magnetic field) and current sheath ionizing front IF (interface plasma-neutral gas) are performed in the radial compression stage of DPF discharges. At the optimum deuterium pressure for neutron yield (1.5 mb), MP and IF have similar r(t) functions, so that the thickness of the sheath remains practically constant (~0.2 cm) in the whole stage. At the lower pressure limit for neutron yield (1 mb) the sheath begins the radial compression stage with a smaller thickness (~0.1 cm) and in the last 35 ns the IF moves forward (relatively to the MP) with a velocity of 7.5E+7 cm/s and the thickness in the layer reaches a value of ~0.5 cm. This sudden acceleration of the IF is interpreted as the main cause of the lower pressure limit in the neutron yield     

Electron beam extraction from a broad-beam vacuum-arc metal plasmasource

We describe experiments demonstrating the formation of a high current electron beam from a vacuum arc plasma. A preexisting vacuum arc ion source was used, with the extraction voltage reversed in polarity so as to form an electron beam rather than an ion beam; no other changes were required. The beam formed was of energy up to 33 keV, beam current up to 70 A, beam diameter about 10 cm, pulse width 500 μs, and energy density up to 25 J/cm². This kind of source can be used for material surface modification     

Implosion dynamics of a radiative composite Z-pinch

Two-dimensional simulation of a composite Z-pinch was performed by the complete radiative magnetohydrodynamic (MHD) code ZETA including detailed calculation of equations of state, spectral properties of materials, and radiation transport in non-local thermodynamic equilibrium multicharged ions plasma. The initial geometry, the substance components, and the electric current through the Z-pinch were similar to the joint experiment set up JEX-94 at Angara-5 facility. The geometry was: annular argon gas puff with inner and outer diameter of a nozzle cross section, 3 cm and 3.4 cm, respectively, and specific mass of 80 μg/cm. Inside it along the axis a foam cylinder 30% KCl in agar-agar with total mass 60 μg and diameter 1 mm was put. The initial gas distribution was modelled with a divergence of a jet along the Z-axis. A coupling of the Z-pinch with the electric current generator was modelled by an electrical circuit with a given electromagnetic wave, a resistance, an inductance, and a variable load (Z-pinch) similar to the Angara-5-1 output parameters. During the plasma implosion the total current reached the value of 3 MA at a time of 85 ns from the voltage start. Such current amplitude is much less than through the matched load (up to 4 MA as a rule): The plasma implosion is accompanied by the development of different types of short and long wave instabilities (thermal, radiative, nonisothermal, and MHD Rayleigh-Taylor modes). In this report, the detailed plasma implosion dynamics, the influence of instabilities, and the spectral radiation yield are discussed, and a comparison with the experimental results is done     

Optical measurements of plasma dynamics in carbon fiber Z-pinches

A series of experiments has been carried out on the Mega Ampere Generator for Plasma Implosion Experiments (MAGPIE) generator in order to study the dynamics of carbon fiber Z-pinches. The generator was operated at 1.4 MV, with a peak current of 1 MA, and a rise time of 150 ns. In some shots, a current prepulse of about 30 kA was provided to study its influence on the dynamics of the fiber pinch. Carbon fibers of 7, 33, and 300 μm diameter were used during these experiments. The diagnostics employed were a self-referencing interferometer, a two-frame Schlieren system, an optical streak camera, and a four-frame X-ray framing camera. A novel feature of these measurements is the employment of an optical streak camera with a set of four slits arranged along the fiber axis and displaced in the radial direction. This permitted the study of the temporal evolution (axial and radial) of the plasma regions emitting in the visible part of the spectra. Correlation between these regions of the plasma and the location of X-ray hot spots is discussed. In carbon fibers of 33 pm diameter, the radial expansion velocity measured from Schlieren images was 3.6×10⁶ cm/s and 5.5×10⁶ cm/s for shots with and without prepulse, respectively. The dominant axial wavelengths of instabilities in the coronal plasma were between 0.05 and 0.2 cm, which correspond to ka values between 10 and 20, where k is the wavenumber of the instability and a is its amplitude. The dynamics of carbon fibers of different diameters are compared     

Cathode Sheath Instability at Frequencies Near the Ion Plasma Frequency

We consider steady-state and nonstationary processes in a near-cathode region. Equations describing the plasma dynamics near a cathode at frequencies close to the ion plasma frequency are derived, and solutions of these equations for various zones of a discharge gap are found. A piecewise-uniform model of a cathode sheath is developed, which points out the possibility of an instability at a frequency slightly less than the near-cathode ion plasma frequency. The gas pressure effect on the instability threshold with respect to the discharge current is considered. The obtained results are in good agreement with the data of experimental studies of the cathode sheath in a hollow-cathode discharge.     

High-speed all-optical switching in ion-implanted silicon-on-insulator microring resonators

We demonstrate high-speed all-optical switching via vertical excitation of an electron-hole plasma in an oxygen-ion implanted silicon-on-insulator microring resonator. Based on the plasma dispersion effect the spectral response of the device is rapidly modulated by photoinjection and subsequent recombination of charge carriers at artificially introduced fast recombination centers. At an implantation dose of 1 x 10(12) cm(-2) the carrier lifetime is reduced to 55 ps, which facilitates optical switching of signal light in the 1.55 mum wavelength range at modulation speeds larger than 5 Gbits/s.     

Importance of high local cathode spot pressure on the attachment ofthermal arcs on cold cathodes

The importance of having high local cathode spot pressures for the self-sustaining operation of a thermal arc plasma on a cold cathode is theoretically investigated. Applying a cathode sheath model to a Cu cathode, it is shown that cathode spot plasma pressures ranging 7.4-9.2 atm and 34.2-50 atm for electron temperatures of ~1 eV are needed to account for current densities of 10⁹ and 10¹⁰ A·m^-2, respectively. The study of the different contributions from the ions, the emission electrons, and the back-diffusing plasma electrons to the total current and heat transfer to the cathode spot has allowed us to show the following. 1) Due to the high metallic plasma densities, a strong heating of the cathode occurs and an important surface electric field is established at the cathode surface causing strong thermo-field emission of electrons. 2) Due to the presence of a high density of ions in the cathode vicinity, an important fraction of the total current is carried by the ions and the electron emission is enhanced. 3) The total current is only slightly reduced by the presence of back-diffusing plasma electrons in the cathode sheath. For a current density j_tot=10⁹ A·m^-2 , the current to the cathode surface is mainly transported by the ions (76-91% of j_tot while for a current density j_tot = 10¹⁰ A·m^-2, the thermo-field electrons become the main current carriers (61-72% of j_tot). It is shown that the cathode spot plasma parameters are those of a high pressure metallic gas where deviations from the ideal gas law and important lowering of the ionization potentials are observed     

Investigation of photoplasma that is configured in an electrostatic extractor having high-temperature electrodes

In the present work we report the investigation of photoplasma in a high temperature electrostatic extractor. The extractor can operate at temperatures ~900 K, at electric field ~200 V/cm and in an environment where there is metal vapor and photon flux. It is used concurrently with another vapor generating furnace that is placed below it. It is observed that for operation over long duration (~5 h) barium atoms from the vapor-producing furnace coat the electrodes. They are re-evaporated from the hot electrodes thereby forming a collision-less vapor cell between them. Multi-step, multi-wavelength resonant ionization process using lasers produce photoplasma in the cell. Thermionic emission from barium coated hot electrodes provides the seed current flux for electron-impact ionization of the atoms in the cell. The ionized background plasma provides a steady state current between the electrodes. The transient photoplasma motion is superimposed on it. The photoions decay as the ions are collected. The Bohm current and current due to sheath boundary motion determines their evolution.     

Unmanned air vehicle flow separation control using dielectric barrier discharge plasma at high wind speed

The present paper described an experimental investigation of separation control of an Unmanned Aerial Vehicle(UAV)at high wind speeds.The plasma actuator was based on Dielectric Barrier Discharge(DBD)and operated in a steady manner.The flow over a wing of UAV was performed with smoke flow visualization in theΦ0.75 m low speed wind tunnel to reveal the flow structure over the wing so that the locations of plasma actuators could be optimized.A full model of the UAV was experimentally investigated in theΦ3.2 m low speed wind tunnel using a six-component internal strain gauge balance.The effects of the key parameters,including the locations of the plasma actuators,the applied voltage amplitude and the operating frequency,were obtained.The whole test model was made of aluminium and acted as a cathode of the actuator.The results showed that the plasma acting on the surface of UAV could obviously suppress the boundary layer separation and reduce the model vibration at the high wind speeds.It was found that the maximum lift coefficient of the UAV was increased by 2.5%and the lift/drag ratio was increased by about 80%at the wind speed of 100 m/s.The control mechanism of the plasma actuator at the test configuration was also analyzed.