Simultaneous determination of tin and lead by a.c. anodic stripping voltammetry at a hanging mercury drop electrode sensitized by cetyltrimethylammoniu

The influence of cetyltrimethylammonium bromide (CTAB) on the simultaneous determination of tin(IV) and lead(II) by anodic stripping voltammetry at a hanging mercury drop electrode (HMDE) in a 0.1 M hydrochloric acid—0.1 M oxalic acid medium was studied using d.c. and a.c. stripping. In the presence of CTAB, tin and lead show voltammetric peaks separated by 100 mV, the sensitivity depending on the concentration of CTAB. The best conditions for the simultaneous determination of both elements (2 × 10^-3 M) were found. A method is proposed for the determination of tin in the presence of lead and three procedures are given for the determination of lead in the presence of tin.     

Determination of heavy metals and iodide by stripping voltammetry in sodium chloride on mercury-graphite electrodes

The behavior of Cd(II), Pb(II), Cu(II), and I⁻ in the aqueous solutions of sodium chloride is studied by stripping voltammetry. A new version of using an indicator electrode from carbon glass ceramics modified with mercury for the consecutive stripping determination of Cd(II), Pb(II), Cu(II), and iodide is proposed. The mercury-graphite electrode was formed in the solution of a supporting electrolyte based on NH₄Cl, HCl, 0.05 M potassium tetraoxalate (KH₃C₄O₃ · 2H₂O), and 5 × 10⁻⁵ M mercury(II). At first, Cd(II), Pb(II), Cu(II), and then iodide were determined by anodic-cathodic stripping voltammetry after adding a sample solution (table salt, 10–100 mg/mL NaCl).     

The Convenient Determination of Palladium at a Solid Electrode via Adsorptive Stripping Voltammetry at a Glassy Carbon Electrode Modified with a Random Array of Mercury Nanodroplets

The detection of palladium using adsorptive stripping voltammetry reported by Wang et al. (J. Wang, K. Varughese Anal. Chim. Acta 1987, 199, 185 [3]) at a hanging mercury drop electrode is extended to a more convenient solid electrode. To this end a random array of 3.5×10⁸ mercury nanodroplets per cm² (65 nm average diameter) was electrodeposited on a glassy carbon substrate. Adsorptive stripping voltammetry was performed using 2×10^?4 M dimethylglyoxime as a chelating agent for the Pd(II) ion, with accumulation at ?0.20 V vs. SCE for 120 s and a linear detection range of 5–150 μM was determined with a limit of detection of 1.6 μM.     

Direct zinc determination in commercial sulphuric acid by dpasv. Comparison of rotating disc and stationary graphite electrodes

A striking gas technique employed made a direct Zn determination possible at extremely low pH in commercial acid solutions when a stationary impregnated graphite-based mercury film electrode was used. The original Zn(II) concentrations were determined quantitatively by differential pulse anodic stripping voltammetry on 0.5M and 1M sulphuric acid solutions by standard addition and were found to be 2 x 10(-8)M and 4.1 x 10(-8)M, respectively. The influence of mercury ion concentration, pulse amplitude, potential step and pulse repetition time on analytical data was studied and optimized. A rotating disc graphite electrode was also used as a working electrode and was found unreliable for this purpose as hydrogen bubbles were not removed effectively and blocked the working electrode surface.     

Anodic stripping voltammetry with mercury electrodes in extracts of cadmium,lead, thallium and indium diethyldithiocarbamate complexes and analysis of mixtures

The selectivity of the determination of traces of cadmium, lead, thallium and indium is improved by direct coupling of liquid/liquid extraction and anodic stripping voltammetry. Metals are extracted from aqueous solution to benzene or chloroform after the addition of sodium or zinc diethyldithiocarbamate. Stripping voltammetry of Cd, Tl and Pb at a hanging mercury drop electrode or mercury film electrode is done in benzene/methanol medium (1:1) with 0.1 M NaClO₄ as supporting electrolyte. For indium, the medium is chloroform/ethanol/water (1:4:1) with 0.005 M sodium acetate/0.06 M KBr/0.06 M HCl as supporting electrolyte. The complexes in acidic solution can be decomposed by mercury (II) ions, which provides useful shifts of deposition potentials. Calibration graphs are linear at concentrations of about 10^?7 M with a detection limit of 1×10^?8 M. The method is applied to determine a single metal in the presence of a large amount (1000-fold) of interfering metal.     

Mercury-coated carbon fiber microelectrodes : Preparation and some properties

Carbon fibre microelectrodes were made by sealing the fibres into glass and by using heat-shrinkable tubing. The electrodes can be coated with mercury by deposition at ?0.9 V vs. SCE from 0.1 M thiocyanate containing 0.05 mM mercury(II) at pH 2.5. Coulometric measurements and square-wave voltammetry were used to establish the properties of the deposit. Conditions for the deposition and stripping of cadmium are outlined.     

Differential pulse anodic stripping voltammetry of lead (lI) benzoylacetonate in chloroform: Application to the analysis of free-lead gasoline and gas oil samples

The voltammetric characteristics of lead(II) benzoylacetonate in chloroform at the mercury electrode are investigated. The conditions for nearly reversible reduction of lead(II) were optimized. Anodic stripping voltammetry for the determination of trace-lead was developed using differential pulse technique to strip amalgamed lead from hanging mercury drop electrode. The experimental conditions, such as scanning rate of electrode potential and deposition time of lead were optimized. The calibration graph was linear over concentration range 5x10(-8)-10(-6) M of lead(II). The detection limit was 2.5x10(-9) and the relative standard deviation for the determination of 4x10(-7) M Pb(II) was 2%. Preceded by decomposition of organolead compounds with concentrated nitric acid, then ashing at 300 degrees C and a solvent extraction of Pb(II) benzoylacetonate in chloroform, the suitability of the proposed method for the determination of lead in free-lead gasoline and gas oil was demonstrated as a typical example of application.     

Square-wave anodic stripping voltammetric determination of thallium(I) at a Nafion/mercury film modified electrode

A Nafion/mercury film electrode (NMFE) was used for the determination of trace thallium(I) in aqueous solutions. Thallium(I) was preconcentrated onto the NMFE from the sample solution containing 0.01 M ethylenediaminetetraacetate (EDTA), and determined by square-wave anodic stripping voltammetry (SWASV). Various factors influencing the determination of thallium(I) were thoroughly investigated. This modified electrode exhibits good resistance to interferences from surface-active compounds. The presence of EDTA effectively eliminated the interferences from metal ions, such as lead(II) and cadmium(II), which are generally considered as the major interferents in the determination of thallium at a mercury electrode. With 2-min preconcentration, linear calibration graphs were obtained over the range 0.05-100 ppb of thallium(I). An even lower detection limit, 0.01 ppb, were achieved with 5-min accumulation. The electrode is easy to prepare and can be readily renewed after each stripping experiment. Applicability of this procedure to various water samples is illustrated.     

Differential pulse cathodic stripping voltammetry of the copper complexes of glycyl-L-histidyl-glycine at a hanging mercury drop electrode

The behaviour of the copper complexes of glycyl-L-histidyl-glycine (GHG) was investigated using cyclic voltammetry and differential pulse voltammetry after their adsorptive accumulation on the surface of a hanging mercury drop electrode (HMDE). The nature of the observed cathodic and anodic peaks was established and optimum conditions were found for the differential pulse cathodic stripping voltammetric detemination of GHG at the 1 x 10(-8)M concentration level using adsorptive accumulation at -0.20 V vs. Ag/AgCl reference electrode and the cathodic stripping peak around -0.4 V (pH 8.3). This peak corresponds to the reduction of the Cu(I)-GHG complex formed at the HMDE surface as an intermediate in the reduction of Cu(II)-GHG to Cu(O)amalgam.     

金纳米颗粒@碳微球的制备及其电化学检测汞离子性能研究

本文研究了金纳米颗粒@碳微球(Au@CMSs)的制备及水环境中汞离子在该材料上的电化学行为. 实验结果表明,在0.1mol•L^-1 pH = 5.0的NaAc-HAc缓冲溶液中,采用方波伏安法测定汞离子,其浓度与氧化峰电流强度线性良好,相关系数为0.997,检出限为3.69 × 10^-8 mol•L^-1（3σ方法）.     

Preconcentration and determination of mercury(II) at a chemically modified electrode containing 3-(2-thioimidazolyl)propyl silica gel.

A mercury-sensitive chemically modified graphite paste electrode was constructed by incorporating modified silica gel into a conventional graphite paste electrode. The functional group attached to the (3-chloropropyl) silica gel surface was 2-mercaptoimidazole, giving a new product denoted by 3-(2-thioimidazolyl)propyl silica gel, which is able to complex mercury ions. Mercury was chemically adsorbed on the modified graphite paste electrode containing 3-(2-thioimidazolyl)propyl silica (TIPSG GPE) by immersion in a Hg(II) solution, and the resultant surface was characterized by cyclic and differential pulse anodic stripping voltammetry. One cathodic peak at 0.1 V and other anodic peak at 0.34 V were observed on scanning the potential from -0.1 to 0.8 V (0.01 M KNO3; v = 2.0 mV s(-1) vs. Ag/AgCl). The anodic peak at 0.34 V show an excellent sensitivity for Hg(II) ions in the presence of several foreign ions. A calibration graph covering the concentration range from 0.02 to 2 mg L(-1) was obtained. The detection limit was estimated to be 5 microg L(-1). The precision for six determinations of 0.05 and 0.26 mg L(-1) Hg(II) was 3.0 and 2.5% (relative standard deviation), respectively. The method can be used to determine the concentration of mercury(II) in natural waters contaminated by this metal.     

Voltammetric study of the redox behaviour of the Hg(II)/Hg(I)/Hg system at a rotating metal-ring/glassy-carbon disc electrode

The reduction of Hg(II) at a glassy-carbon electrode in various electrolytes has been studied by rotating ring-disc voltammetry. Reduction proceeds directly to metallic mercury in a single 2-electron step. However, at the foot of the wave, and only during the first reduction sweep after pretreatment of the electrode surface, a small amount of Hg(I) species is detected at the ring. The appearance of an Hg(I) intermediate is most pronounced in sulphuric acid solution. The reduction of Hg(II) is found to proceed irreversibly and to be of first order. At sufficiently negative potentials the reduction is convective-diffusion controlled. Stripping voltammetric experiments indicate that the dissolution of mercury gives Hg(II) in complexing electrolytes. In non-complexing electrolytes the initially formed Hg(II) reacts with mercury atoms on the electrode surface to give Hg(I). During electrodissolution, two stripping peaks may be observed as a result of underpotential adsorption of mercury on glassy carbon. The difference in peak potential between the adsorption (mono) layer peak and the bulk mercury peak has been related to the difference in work functions of the deposit (mercury) and substrate (carbon). A rotating glassy-carbon electrode has been used for the anodic stripping determination of mercury. When an appropriate amount of a cation such as cadmium(II) or copper(II) is added to the test solution, mercury down to 2 x 10(-9)M (0.4 ng ml ) can be determined in acidified thiocyanate electrolyte with a relative standard deviation of about 22%.     

Electrode Modified with Langmuir–Blodgett (LB) Film of Calixarenes for Preconcentration and Stripping Analysis of Hg(II)

A new type of current sensor, Langmuir–Blodgett (LB) film of calixarene on the surface of glassy carbon electrode (GCE) was prepared for determination of mercury by anodic stripping voltammetry (ASV). An anodic stripping peak was obtained at 0.15 V (vs. SCE) by scanning the potential from ?0.6 to +0.6 V. Compared with a bare GCE, the LB film coated electrode greatly improves the sensitivity of measuring mercury ion. The fabricated electrode in a 0.1 M H₂SO₄+0.01 M HCl solution shows a linear voltammetric response in the range of 0.07–40 μg L^?1 and detection limit of 0.04 μg L^?1 (ca. 2×10^?10 M). The high sensitivity, selectivity, and stability of this LB film modified electrode demonstrates its practical application for a simple, rapid and economical determination of Hg²⁺ in a water sample.     

Cathodic stripping voltammetry and adsorptive stripping voltammetry of selenium(IV)

Cathodic stripping voltammetry of selenium(IV) in 0.1 M hydrochloric acid media yielded a nonlinear calibration graph for the concentration range 10^?9?10^?8 M. In this concentration range, adsorptive stripping voltammetry based on adsorption of the selenium/3,3′-diaminobenzidine complex on the surface of the hanging mercury drop electrode at the deposition potential of +0.05 V (vs. SCE) is more convenient. A linear calibration graph is obtained for selenium concentrations of 3×10^?9?3×10?8 M, with an accumulation time of 300 s.     

Determination of selenium(IV) by cathodic stripping voltammetry using a copper-modified mercury-film electrode modified with copper

The behavior of selenium(IV) at a mercury-film electrode previously modified with copper was studied by cathodic stripping voltammetry using an automatic system for replacing solutions without opening the circuit. The effect of chemical (the composition and concentration of the supporting electrolyte, the concentrations of mercury (II) and copper(II)) and electrochemical parameters (the potential and time of electrolysis) on the analytical signal of selenium was studied at each stage of the stripping cycle (the formation of the mercury-film electrode modified with copper, the electrochemical preconcentration of selenium, and the subsequent stripping of the concentrate). The detection limit for selenium(IV) was found to be 40 ng/L (5.0 × 10^?10 M) at an electrolysis time of 10 min.     

Differential pulse polarography of cadmium-and lead-urate and adsorptive stripping voltammetric determination of uric acid

The complex formation between uric acid and zinc, cadmium and lead ions has been investigated using differential pulse polarography in 0.01M NaNO(3). It is found that the complexes formed by Cd(II) and Pb(II) ions with uric acid have the stoichiometry of 1:2 and the logarithmic values of the apparent stability constant are 9.47 and 11.7, respectively. On the other hand, zinc(II) ions do not give any indication of complexation with uric acid. A sensitive voltammetric method is developed for the quantitative determination of uric acid. This method is based on controlled adsorptive preconcentration of uric acid on the hanging mercury drop electrode (HMDE), followed by tracing the voltammogram in the cathodic going potential scan. The modes used are direct current stripping voltammetry (DCSV) and differential pulse stripping voltammetry (DPSV). The detection limits found were 8 x 10(-9)M (quiescent period 15 sec) by DPSV and 1.6 x 10(-8)M by DCSV.     

Coal as a New Carbon Paste Electrode Modifier with Sorption Properties

A new type of carbon paste electrode modified with subbituminous and bituminous coal is presented. The operability of the coal carbon paste electrode with respect to the working potential window attainable was tested in various electrolytes. Cyclic voltammetry of the reference redox system [Fe(CN)₆]^3?/4? was performed to evaluate electron transfer kinetics. Open‐circuit sorption of Cd(II), Pb(II), and Cu(II) with subsequent anodic stripping voltammetry was used to pilot coal sorption ability. The coal modified carbon paste electrode was also examined as a support for mercury film deposition and anodic stripping voltammetry of metals.     

Catalytic stripping analysis: sensitivity enhancement for reciprocal derivative constant-current stripping determination of palladium in the presence of tin(II) during stripping

The reciprocal derivative constant-current stripping signal of palladium at a mercury film electrode is increased, as in anodic stripping voltammetry (ASV), by a factor of ca. 80 if a certain amount of tin(II) is present in the stripping solution. This catalytic stripping phenomenon has been successfully used as a means of sensitivity enhancement in constant-current stripping determination of trace palladium. The limit of detection is 4 x 10(-10)M at S/N = 3, which is about two decades lower than that obtained without tin(II) present. Linear response was observed over the range 10(-10)-10(-7)M. This method has been applied to determine palladium in waste water and mineral samples. The experimental results support the postulated mechanism of signal enhancement, namely a chemical redeposition reaction occurring during the stripping, giving a cycle of stripping and deposition and thus increasing the stripping signal.     

An electroanalytical study of the anticancer drug dacarbazine

The electrochemical behaviour of dacarbazine [5-(3,3-dimethyl-1-triazenyl) imidazole-4-carboxamide; DTIC] was investigated by Tast and differential pulse polarography (d.p.p.) at the dropping mercury electrode, by cyclic and differential pulse voltammetry at the hanging mercury drop electrode and by anodic voltammetry at the glassy carbon electrode. Calibration graphs were obtained for 2×10^?8?2×10^?5 M DTIC by d.p.p., for 5×10^?9?1×10^?5 M by adsorptive stripping voltammetry ar a hanging mercury drop electrode, and for 1?10×10^?5 M by high-performance liquid chromatography with oxidative amperometric detection at a glassy carbon electrode. The methods are compared and applied to determine DTIC added to blood serum after a simple clean-up procedure.     

Use of binary metal deposits on a cylindrical carbon-fiber microelectrode in the voltammetric determination of metal ions

The effect of binary metal deposits on a cylindrical carbon-fiber microelectrode on the determination of metals by direct and stripping voltammetry was studied. The electrolytic deposition of a binary system of copper and thallium, cadmium, lead, or mercury on the electrode in an alkaline solution resulted in the disappearance of the electroreduction peak of dissolved oxygen in the potential range from -0.8 to -1.4 V and in a decrease in the background current. Under the conditions of limited diffusion, the peak currents of Ni(II), Co(II), and Zn(II) in differential pulse voltammograms were 3–7 times higher than those calculated for a reversible electrode process under the conditions of semi-infinite diffusion. Because of this, the determination limit for metal ions in direct voltammetry was lowered to 1 X 10^-6 M. With a binary copper-thallium system, the peak current of zinc(II) reduction can be be detected in the presence of 5000-fold molar amounts of copper(II). The deposition of binary copper-lead and copper-thallium systems under the conditions of limited diffusion reduced the effect of negative interaction between the components of these systems and made possible the determination of lead(II) and thallium(I) by stripping voltammetry using additional peaks.