大口径火炮焊接药筒射击变形机理的启发式反演

在某大口径火炮焊接钢药筒退壳后残余变形实际测量现象规律的基础上,运用非线性有限元分析作为物理模型正问题分析工具,对火炮发射过程中影响该药筒行为的关键因素和作用机理进行启发式反演。通过有限元反演计算,揭示了筒体上热冲击引起的瞬态温升是决定药筒残余变形和抽壳阻力的一个关键因素,得到了筒体瞬态温度增量分布规律。在此基础上通过有限元分析获得的药筒抽壳阻力与实际测试结果一致。     

?????帪??????б???????????????

根据抗拉刚度等效及抗弯刚度等效将换热器管束简化为当量圆筒以考察其对 斜锥壳应力状况的影响,同时根据轴向载荷等效及泊松效应等效,对作用在管板布管限定圆 内的压力载荷及作用在管束外表面的压力载荷进行了当量转换,建立了考虑管板及管束影响 的斜锥壳应力分析简化模型. 有限元计算结果表明,大端转角过渡区存在较大的弯曲应力. 对一系列结构尺寸的斜锥壳进行了计算,整理了斜锥壳大端转角过渡区基于分析设计的应力 强度水平系数.     

轴向应力波作用下圆柱壳弹性轴对称动力失稳有限元特征值分析

本文运用有限元特征值分析方法对应力波作用下圆柱壳弹性轴对称动力失稳问题进行了研究。基于应力波理论和相邻平衡准则导出了圆柱壳轴对称动力失稳时的有限元特征方程,在此方程中考虑了应力波效应及横向惯性效应,把圆柱壳弹性动力失稳问题归结为特征值问题。通过引入圆柱壳动力失稳时的波前约束条件实现了此类问题的有限元特征值解法。计算结果揭示了圆柱壳弹性轴对称动力屈曲变形发展的机理,以及轴向应力波和屈曲变形的相互作用规律。     

轴向应力波作用下圆柱壳塑性轴对称动力屈曲

运用有限元特征值分析方法对应力波作用下圆柱壳塑性轴对称动力失稳问题进行了研究。基于应力波理论和相邻平衡准则导出了圆柱壳轴对称动力失稳时的特征方程,在分析中同时考虑了应力波效应及横向惯性效应,把圆柱壳塑性动力失稳问题归结为特征值问题。通过引入圆柱壳动力失稳时的波前约束条件实现了此类问题的有限元特征值解法。计算结果揭示了圆柱壳塑性轴对称动力屈曲变形发展的机理,以及轴向应力波和屈曲变形的相互作用规律。     

轴向冲击载荷作用下锥壳中弹性应力波传播的计算和实验研究

本文利用有限元分析和模型实验研究了在轴向冲击载荷作用下,锥壳中弹性应力波的传播、计算和实验结果表明,结构中存在着弹性纵波和弹性弯曲波的传播,它们传播的速度各不相同,使壳面承受不同的应力状态;讨论了纵波和弯曲波随壳面的衰减;实验指出,由于边界的影响,即使纵波的反射也会产生新的反射弯曲波沿锥面传播。     

埋头弹药发射过程药筒力学特性分析

埋头弹药是一种新型战场用弹药,自动机采用旋转闭锁新原理,供弹与退壳同步进行。在发射过程中埋头弹药的工况不同于传统的弹药筒,针对埋头弹药在特殊工作条件下药筒内压变化及变形特征,分析了药筒的动力学过程,获得了药筒在贴壁前、贴壁后、卸载过程的力学特性。通过数值分析发现:在最大膛压为400MPa条件下,聚乙烯药筒性能良好,卸压后能迅速弹性恢复。在此基础上设计了金属与塑料耦联的35mm埋头弹药筒,射击实验表明该药筒满足连发射击要求。     

纵横加肋圆柱壳的应力分析

建立了一种纵横加肋圆柱壳有限元分析的正确的力学模型,通过大量数值计算,论证了纵骨尺寸,纵骨间距对壳体应力状态的影响,提出了一种等效各向同性壳的近似解析公式,为开展纵横加肋圆柱壳的结构设计打下了良好的基础。     

圆柱壳的非线性动力屈曲分析

本文研究在轴向冲击作用下，具有初始几何缺陷的圆柱壳的非线性弹性动力屈曲问题。由于冲击过程中作用时间极短，应力波的影响变得相当重要，同时认为圆柱壳经历大挠度变形。分析中不仅考虑圆柱壳的径向惯性力，而且也考虑轴向惯性力和几何非线性的影响。假设圆柱壳中位移和薄膜力可分成轴对称分量和非轴对称分量之和，并引入应力函数表示非轴对称内力，对平衡方程应用伽辽金方法，将导出的和冲击物体的质量对动屈曲性能的影响很大。     

分区样条等参元方法分析加助轴对称组合壳

本文提出分区样条行动等参元方法分析加肋轴对称组合壳在静水外压作用下的应力及稳定性，该方法根据母线几何形状，壳板厚度变化及边界约束状况将加肋轴对称组合壳划分为若干个区域，在不同区域采用不同步长的样条等参元进行分析，因而便于对复杂的组合壳进行分析，并可大大减少计算所需自由度数，减少计算工作量，同时计算精度很高，并且易于进行边界约束处理，应用该方法对加肋锥－柱，加肋锥－环－柱组合壳进行了计算，其结果与其     

大型爆炸防护结构的动态应力测试与分析

对某大型爆炸防护结构进行不同工况的爆炸实验,通过电测法测量了几个典型位置的应力,结果 显示:从第1和第2主应力测试结果来看,球壳表面在爆炸冲击作用下的冲击应力峰值除第1次最大外,之后 基本以拉压应力状态来回振动,而且振动应力在经过1~2个来回后立刻减小到100 MPa以下,土的堆压可 以起到削弱球壳振动的作用,因此球壳单次爆炸引起的振动疲劳问题大为削弱;模型的强度满足设计要求;排 气孔附近是应力最为集中区域;炸药的形状系数对结构的安全影响很大。     

电缆绕组变压器线圈短路机械强度的计算

在变压器T型等值电路基础上,求得变压器短路最严重情况对应的起始条件和出现最大短路电流时刻。以此起始条件设定变压器原边电压激励,利用“磁路-电路”耦合有限元法建立了2D轴对称模型,计算了变压器原、副边线圈及各线匝短路电磁力。以出现最大轴向和径向电磁力的线匝为研究对象,结合电缆绕组变压器的受力特点,建立了单线匝短路条件下的静态和动态有限元模型。选择第四强度破坏理论,分别计算了静态和动态时线匝相当应力分布。讨论了静态时相当应力与预紧压强、撑条根数的关系;分析了相当应力随时间的变化规律,并与静态对应情况进行了比较。     

钢桁腹式混凝土组合箱梁翼板纵向应力的计算方法研究

为研究钢桁腹式混凝土组合箱梁翼板纵向应力沿横桥向的分布情况,运用有限元软件ANSYS建立一座35m等截面简支钢桁腹式混凝土组合箱梁的有限元模型,考虑斜向腹杆杆力作用会使翼板产生附加轴力及相应的附加应力,故利用能量变分法原理推导出组合箱梁的翼板纵向弯曲应力和纵向附加应力计算公式,并据此探讨适用于计算组合箱梁的翼板纵向应力的方法。将有限元值和理论值进行比较,吻合程度良好。研究结果表明,组合箱梁的下翼板纵向应力可采用纵向弯曲应力计算公式进行计算;为获得组合箱梁的翼板附加轴力,可将组合箱梁的钢桁腹杆和混凝土纵梁取出,认为两者通过节点构造共同构成平面桁架,翼板附加轴力即为平面桁架的弦杆杆力;组合箱梁的上翼板纵向应力可通过纵向弯曲应力和经修正的纵向附加应力叠加获得。     

MOTION AND DEFORMATION OF VISCOUS DROP IN STOKES FLOW NEAR RIGID WALL

A boundary integral method was developed for simulating the motion and deformation of a viscous drop in an axisymmetric ambient Stokes flow near a rigid wall and for direct calculating the stress on the wall. Numerical experiments by the method were performed for different initial stand-off distances of the drop to the wall, viscosity ratios, combined surface tension and buoyancy parameters and ambient flow parameters. Numerical results show that due to the action of ambient flow and buoyancy the drop is compressed and stretched respectively in axial and radial directions when time goes. When the ambient flow action is weaker than that of the buoyancy the drop raises and bends upward and the stress on the wall induced by drop motion decreases when time advances. When the ambient flow action is stronger than that of the buoyancy the drop descends and becomes flatter and flatter as time goes. In this case when the initial stand-off distance is large the stress on the wall increases as the drop evolutes but when the stand-off distance is small the stress on the wall decreases as a result of combined effects of ambient flow, buoyancy and the stronger wall action to the flow. The action of the stress on the wall induced by drop motion is restricted in an area near the symmetric axis, which increases when the initial stand-off distance increases. When the initial stand-off distance increases the stress induced by drop motion decreases substantially. The surface tension effects resist the deformation and smooth the profile of the drop surfaces. The drop viscosity will reduce the deformation and migration of the drop.     

埋地冲洗管线强度计算及影响因素规律分析

研究了冲洗管线在自重、内压、温差和土壤力综合作用下的强度分析方法,给出埋地冲洗管线应力计算公式。采用有限单元法对某冲洗管线重点部位进行力学特性分析,得到其真实应力分布状态,对比了理论计算结果与数值结果误差,证实轴向应力理论计算结果偏保守。对不同壁厚、不同环境温度和不同压力下的管线力学特性进行讨论,结果表明,管道的环向应力起主导作用,且埋深0m~0.75m内管线的环向应力变化明显,因此,当考虑温差及波动内压作用时,该段管线力学特性应引起足够重视;受环境温度影响,管线最大等效应力与总位移规律近似相反,即等效应力最小,总位移近似最大;考虑到等效应力随压力变化规律,不同季节宜采用不同的冲洗压力以满足安全运行要求。     

双向张弦梁找形的有限元法

根据双向张弦梁上弦压力和下弦拉力在节点产生的竖向分力与撑杆高度之间的关系推导了单元刚度矩阵,根据外荷载与上弦和下弦在节点产生的竖向分力相等的原则建立了以撑杆高度为未知数的双向张弦梁找形的线性有限元列式并编制了有限元程序,给出了张弦梁计算时下弦拉索初应变确定方法和张拉控制方法;通过对平屋顶和曲面屋顶双向张弦梁2个算例找形计算和受力分析验证了找形方法的正确性以及撑杆高度与屋面形状的无关性,本文给出的计算方法将撑杆高度作为未知量,考虑了上弦为曲面时拱的作用,计算方便、结果准确.     

Constitutive Model Calibration for Powder Compaction Using Instrumented Die Testing

Calibration procedures for constitutive models for powder compaction are presented. A practical calibration method based on a die compaction experiment is presented. A newly developed apparatus consisting of a die instrumented with radial stress sensors is described. The paper proposes two contributions to account for errors present in instrumented die testing, which are due to 1) elastic compliance of the testing frame, influencing the measurement of axial strain and 2) the presence on non-homogeneous stress state in the test specimen. It is shown that system compliance is important for generating an accurate stress-strain curve for compression. The effect of different compliance correction methods is evaluated with regard to the accuracy of models predicting pressing forces. The system compliance becomes more significant during unloading in the die; this information is used to determine the elastic properties. A new compliance correction method is introduced following a detailed analysis of the forces and deformations of different parts of the loading frame. In instrumented die compaction the axial and radial stresses are measured at fixed locations and the specimen is subject to non-homogeneous stresses and strains due to the effect of friction between the powder and die wall. Starting from the Janssen-Walker method of differential slices a method to account for non-homogeneous stress and strain is developed.     

Dynamic response of a deepwater riser subjected to combined axial and transverse excitation by the nonlinear coupled model

In offshore engineering long slender risers are simultaneously subjected to both axial and transverse excitations. The axial load is the fluctuating top tension which is induced by the floater’s heave motion, while the transverse excitation comes from environmental loads such as waves. As the time-varying axial load may trigger classical parametric resonance, dynamic analysis of a deepwater riser with combined axial and transverse excitations becomes more complex. In this study, to fully capture the coupling effect between the planar axial and transverse vibrations, the nonlinear coupled equations of a riser’s dynamic motion are formulated and then solved by the central difference method in the time domain. For comparison, numerical simulations are carried out for both linear and nonlinear models. The results show that the transverse displacements predicted by both models are similar to each other when only the random transverse excitation is applied. However, when the combined axial dynamic tension and transverse wave forces are both considered, the linear model underestimates the response because it ignores the coupling effect. Thus the coupled model is more appropriate for deep water. It is also found that the axial excitation can significantly increase the riser’s transverse response and hence the bending stress, especially for cases when the time-varying tension is located at the classical parametric resonance region. Such time-varying effects should be taken into account in fatigue safety assessment.     

血管残余应力的一种确定方法

动脉无载荷状态下存在残余应力,分析血管壁在载荷状态下的应力分布必须计及血管壁的残余应力。本文通过检测动脉不同轴向伸长比条件下的压力—容积(p—V)数据,根据其p—V实验曲线的“S”型特征,提出了一种用反正切函数关系对试验数据点进行拟合,进而导得动脉管壁周向残余应力沿壁厚分布的方法。文章对10只正常大鼠颈动脉的分析结果表明,大鼠颈动脉周向残余应力沿血管壁厚呈单调上升趋势。残余应力在内壁处为负呈压缩状态,在外壁处为正呈拉伸状态,并且内外壁处应力绝对值大小基本相等,大约在2．5kPa左右。文章结果对进一步分析动脉管壁在载荷作用下的应力分布提供必要的信息。     

Curvature effects on axially compressed buckling of a small-diameter double-walled carbon nanotube

The curvature effects of interlayer van der Waals (vdW) forces on axially compressed buckling of a double-walled carbon nanotube (DWNT) of diameter down to 0.7 nm are studied. Unlike most existing models which assume that the interlayer vdW pressure at a point between the inner and outer tubes depends merely on the change of the interlayer spacing at that point, the present model considers the dependence of the interlayer vdW pressure on the change of the curvatures of the inner and outer tubes at that point. A simple expression is derived for the curvature-dependence of the interlayer vdW pressure in which the curvature coefficient is determined. Based on this model, an explicit formula is obtained for the axial buckling strain. It is shown that neglecting the curvature effect alone leads to an under-estimate of the critical buckling strain with a relative error up to −7%, while taking the average radius of two tubes as the representative radius and the curvature effect leads to an over-estimate of the critical buckling strain with a relative error up to 20% when the inner radius downs to 0.35 nm. Therefore, the curvature effects play a significant role in axially compressed buckling problems only for DWNTs of very small radii. In addition, our results show that the effect of the vdW interaction pressure prior to buckling of DWNTs under pure axial stress is small enough and can be negligible whether the vdW interaction curvature effects are neglected or not.     

Iterative dipole moment method for calculating dielectrophoretic forces of particle-particle electric field interactions

Dielectrophoresis (DEP) is one of the most popular techniques for bio-particle manipulation in microfluidic systems. Traditional calculation of dielectrophoretic forces of single particle based on the approximation of equivalent dipole moment (EDM) cannot be directly applied on the dense particle interactions in an electrical field. The Maxwell stress tensor (MST) method is strictly accurate in the theory for dielectrophoretic forces of particle interaction, but the cumbersome and complicated numerical computation greatly limits its practical applications. A novel iterative dipole moment (IDM) method is presented in this work for calculating the dielectrophoretic forces of particle-particle interactions. The accuracy, convergence, and simplicity of the IDM are confirmed by a series of examples of two-particle interaction in a DC/AC electrical field. The results indicate that the IDM is able to calculate the DEP particle interaction forces in good agreement with the MST method. The IDM is a purely analytical operation and does not require complicated numerical computation for solving the differential equations of an electrical field while the particle is moving.