Multiplication of electronic excitations in nanophosphors Lu2O3:Eu and Lu2O3:Tb

Luminescence properties of Lu₂O₃:Eu³⁺ and Lu₂O₃:Tb³⁺ nanocrystalline powders with the particle size varying from 46 to 6 nm were studied under excitation by synchrotron radiation in the photon energy range (up to ∼22.5 eV) covering the region where the processes of multiplication of electronic excitation occur. It was found that the excitation spectra of Tb³⁺ emission from all Lu₂O₃:Tb³⁺ nanopowders have similar behavior, whereas the shape of the excitation spectra of Eu³⁺ emission from Lu₂O₃:Eu³⁺ nanopowders strongly depends on the particle size. The difference in the behavior of Lu₂O₃:Eu³⁺ and Lu₂O₃:Tb³⁺ nanophosphor systems was explained by different mechanisms of the energy transfer from the host to Eu³⁺ or Tb³⁺ ions (either the hole or electron recombination mechanism, respectively), which are differently influenced by losses of electronic excitations near the particle surface.     

Upconversion emission enhancement of TiO2 coated lanthanide-doped Y2O3 nanoparticles

To investigate the upconversion emission,this paper synthesizes Tm3+ and Yb3+ codoped Y2O3 nanoparticles,and then coats them with TiO2 shells for different coating times.The spectral results of TiO2 coated nanoparticles indicate that upconversion emission intensities have respectively been enhanced 3.2,5.4,and 2.2 times for coating times of 30,60 and 90 min at an excitation power density of 3.21×102 W.cm 2,in comparison with the emission intensity of non-coated nanoparticles.Therefore it can be concluded that the intense upconversion emission of Y2O3:Tm3+,Yb3+ nanoparticles can be achieved by coating the particle surfaces with a shell of specific thickness.     

Synthesis, characterization, and luminescent properties of Lu2O3:Eu phosphors

Eu-doped lutetia (Lu₂O₃:Eu) nano-phosphors were synthesized by the sol-gel combustion process from a mixed aqueous solution of europium and lutetium nitrates, using organic glycine as the fuel. Powder X-ray diffraction shows that cubic Lu₂O₃:Eu crystallites are directly obtained by the sol-gel combustion process without further calcination. Electron microscopy reveals that the as-prepared phosphors are agglomerated and have a fluffy, fine, and porous morphology, consisting of primary particle size of 8-10 nm. The excitation spectrum is characterized by three dominant bands centered at 395, 466, and 534 nm, respectively. Both the photoluminescent and radioluminescent spectra are very similar and exhibit intense emission peaks centered at 612 nm due to ⁵D₀→⁷F₂ transition of Eu³⁺ ions. The energy transfer from Lu₂O₃ host to Eu³⁺ activator is more efficient in the case of calcined phosphors than for the as-prepared phosphors due to their improved lattice perfection.     

Tm3+离子掺杂的钨酸钇钠晶体中浓度猝灭效应的研究

测量了Tm³⁺离子不同浓度(0.5at.%, 3 at.%, 5 at.%)掺杂的NaY(WO₄)₂晶体在800nm激光二极管激发下的上转换发射光谱.结合吸收谱、荧光谱和由Judd-Ofelt理论计算的光谱参数，详细分析了Tm³⁺:NaY(WO₄)₂晶体中上转换能量传递机理和离子浓度对上转换发射的影响.讨论了四种影响上转换发光效率的离子间相互作用机理：³H₅+¹G₄→³H₆+¹D₂，³H₅+³H₅→³H₆+³F₃，¹G₄+³H₆→³F₄+³F₃，¹G₄+³H₆→³F₃+³F₄，并根据Miyakawa-Dexter理论定量计算了各过程的发生概率.论证了交叉弛豫和共协上转换等浓度猝灭效应是影响Tm³⁺离子蓝色上转换荧光发射效率的主要因素. 关键词： 3+离子')" href="#">Tm³⁺离子 4)₂晶体')" href="#">NaY(WO₄)₂晶体 上转换 浓度猝灭     

Influence of postdeposition annealing on structural properties and electrical characteristics of thin Tm2O3 and Tm2Ti2O7 dielectrics

We describe the structural properties and electrical characteristics of thin thulium oxide (Tm₂O₃) and thulium titanium oxide (Tm₂Ti₂O₇) as gate dielectrics deposited on silicon substrates through reactive sputtering. The structural and morphological features of these films were explored by X-ray diffraction, X-ray photoelectron spectroscopy, secondary ion mass spectrometry, and atomic force microscopy, measurements. It is found that the Tm₂Ti₂O₇ film annealed at 800 °C exhibited a thinner capacitance equivalent thickness of 19.8 Å, a lower interface trap density of 8.37 × 10¹¹ eV⁻¹ cm⁻², and a smaller hysteresis voltage of ∼4 mV than the other conditions. We attribute this behavior to the Ti incorporated into the Tm₂O₃ film improving the interfacial layer and the surface roughness. This film also shows negligible degrees of charge trapping at high electric field stress.     

Increase of the blue upconversion emission in YAG:Tm3+ nanopowders by codoping with Yb3+ ions

The YAG nanopowders were prepared by a co-precipitation method using nitrate and ammonium hydrogen carbonate as raw materials. To obtain homogenous precipitate, reverse-strike (adding salt solutions to the precipitant solution) technique was adopted. Therefore, single (Tm³⁺) and codoped (Tm³⁺–Yb³⁺) YAG nanopowders with a size between 40–90 nm have been obtained.Blue upconversion emission at around 480 nm has been found in YAG: Tm³⁺ nanopowders under excitation to the ³H₄ level of Tm³⁺ at around 800 nm. However, this upconversion emission in nanopowders codoped with Tm³⁺–Yb³⁺ ions is increased by a factor of about 10. The analysis of the temporal evolution of the involved levels and the dependence of the upconversion intensity on the pump power at 800 nm allowed to distinguish the upconversion mechanism. In YAG: Tm³⁺ nanopowders the upconversion mechanism is due to excited state absorption processes. However, in the codoped samples, Yb³⁺ ions acts as the sensitizers; in consequence, the blue upconversion is strongly increased.     

Emission analysis of Pr and Tm: Ca2Gd2W3O14 phosphors

5 mol% of Pr³⁺ and Tm³⁺ ions activated calcium gadolinium tungstate (Ca₂Gd₂W₃O₁₄₎ phosphors were synthesized by traditional solid state reaction method. Crystalline phase structure was identified from the X-ray diffraction (XRD) profiles. From the scanning electron microscopy (SEM) images, we have observed the agglomeration of the particles, and average grain size is around 40-300 nm. Using the energy dispersive X-ray analysis (EDAX) and Fourier transform infrared (FTIR) spectra, identified the elements and functional groups present in the prepared phosphors. The emission spectrum of Pr³⁺: Ca₂Gd₂W₃O₁₄ powder phosphors have shown an intense red emission at 615 nm with the excitation wavelength λ_exci=450 nm and thus these red color emitting powder phosphors are used as one of the components in the preparation of WLEDs. The excitation spectrum of Tm³⁺: Ca₂Gd₂W₃O₁₄ powder phosphor has shown a ligand to metal charge transfer (W-O) band (LMCT) within the WO₄²⁻ group. Emission spectrum of Tm³⁺: Ca₂Gd₂W₃O₁₄ phosphors have shown blue emissions at 453 nm (¹D₂→³F₄).     

Role of Al2O3 in upconversion and NIR emission in Tm and Er codoped calcium fluoro phosphorous silicate glass system

In this study, the principal role of Al₂O₃ on the features of the photoluminescence spectra of Tm³⁺ ion and upconversion phenomenon in Tm³⁺ and Er³⁺ codoped CaF₂−Al₂O₃−P₂O₅−SiO₂ glass system has been investigated. The concentration of Al₂O₃ is varied from 2 to 10 mol% while that of Er³⁺ and Tm³⁺ is fixed. IR and Raman spectral studies have indicated that there is a gradual increase in the degree of disorder in the glass network with increase in the concentration of Al₂O₃ up to 6.0 mol%. This is attributed to the presence of Al³⁺ ions in octahedral positions in larger proportions. When the glasses are doped with Tm³⁺ ions, the blue and red emissions were observed, whereas in Er³⁺ doped glasses blue, green and red emissions were observed. When the glasses are codoped with Tm³⁺ and Er³⁺ ions and excited at 790 nm, all the three emission lines were observed to be reinforced, especially in the glasses mixed with 6.0 mol% of Al₂O₃. The IR emission band detected at about 1.8 μm due to ³F₄→³H₆ transition of Tm³⁺ ions is also observed to be strengthened due to codoping. The reasons for enhancement in the intensity of various emission bands due to codoping have been identified and discussed with the help of rate equations for various emission transitions.     

Influence of Lu2O3 on electrical and microstructural properties of CaCu3Ti4O12 ceramics

In this work, the influence of Lu₂O₃ doped on the dielectric and electrical properties of CaCu₃Ti₄O₁₂ was reported. Lu₂O₃-doped CCTO was prepared by a conventional solid state technique using CuO, TiO₂, and CaCO₃ as starting materials. The samples were studied by X-ray diffraction (XRD) and scanning electron microscopy (SEM); dielectric measurements were measured in the 10² Hz–10⁷ Hz frequency range at room temperature; and the nonlinear behavior of all samples was measured. The doping of Lu₂O₃ resulted in an increase in the dielectric constant of CCTO, but decreased the stability of the frequency dependence. Increasing concentrations of Lu₂O₃ resulted in decreasing nonlinear coefficients.     

980 nm激发下Er3+/Yb3+共掺杂ZrO2-Al2O3粉末的上转换发光特性

通过固相反应法制备了Er³⁺/Yb³⁺共掺杂ZrO₂-Al₂O₃粉末的样品，并对样品在980nm激光激发下的上转换发光特性进行了研究.从发射光谱可以发现，在可见光范围内有3个强的发光带，一个位于654nm附近的红光带和两个分别位于545nm、525nm附近的绿光带，分别对应于Er³⁺离子的以下辐射跃迁：⁴F_9/2→⁴I_15/2、⁴S_3/2→⁴I_15/2、 ²H_11/2→⁴I_15/2.其中又以Er³⁺离子的⁴F_9/2→⁴I_15/2跃迁产生的红色荧光辐射最强.对其上转换发光机制进行了分析，发现这三个发光过程都是双光子过程.对样品粉末进行了XRD检测，发现ZrO₂主要以立方相为主，并且计算得到了这种立方结构的晶格常数.Al₂O₃固溶于ZrO₂中，Al³⁺嵌入ZrO₂后产生氧空位，导致ZrO₂晶体的对称性降低，这种结构变化更有利于提高上转换效率，即上转换发光强度增强. 关键词： 3+/Yb³⁺')" href="#">Er³⁺/Yb³⁺ 上转换 2-Al₂O₃')" href="#">ZrO₂-Al₂O₃ 荧光 稀土     

Upconversion luminescence and mechanisms in Yb-sensitized Tm-doped oxyhalide tellurite glasses

Effect of Yb₂O₃ content on upconversion luminescence and mechanisms in Yb³⁺-sensitized Tm³⁺-doped oxyhalide tellurite glasses were investigated under 980 nm excitation. Intense blue and relatively weak red upconversion emission centered at 476 and 649 nm corresponding to the transitions ¹G₄→³H₆ and ¹G₄→³H₄ of Tm³⁺, respectively, are simultaneously observed at room temperature. The results show that upconversion blue and red emission intensities of Tm³⁺ first increase, reach its maximum at Yb₂O₃%=3 mol%, and then decrease with increasing Yb₂O₃ content. The effect of Yb₂O₃ content on upconversion intensity is discussed, and possible effect mechanisms are evaluated. The investigated results were conducing to increase upconversion luminescence efficiency of Tm³⁺.     

Enhanced luminescence of Ca3B2O6:Dy phosphors by Na-codoping for LED applications

The Ca_2.95−yDy_0.05B₂O₆:yNa⁺ (0≤y≤0.20) phosphors were synthesized at 1100 °C in air by the solid-state reaction route. The as-synthesized phosphors were characterized by X-ray powder diffraction (XRD), scanning electron microscopy (SEM), photoluminescence excitation (PLE), photoluminescence (PL) spectra and thermoluminescence (TL) spectra. The PLE spectra show the excitation peaks from 300 to 400 nm due to the 4f-4f transitions of Dy³⁺. This mercury-free excitation is useful for solid-state lighting and light-emitting diodes (LEDs). The emission of Dy³⁺ ions on 350 nm excitation was observed at 480 nm (blue) due to the ⁴F_9/2→⁶H_15/2 transitions, 575 nm (yellow) due to ⁴F_9/2→⁶H_13/2 transitions and 660 nm (red) due to weak ⁴F_9/2→⁶H_11/2 emissions. The PL results from the investigated Ca_2.95−yDy_0.05B₂O₆:yNa⁺ phosphors show that Dy³⁺ emissions increase with the increase of the Na⁺ codoping ions. The integral intensity of yellow to blue (Y/B) can be tuned by controlling Na⁺ content. By the simulation of white light, the optimal CIE value (0.328, 0.334) can be achieved when the content of Na⁺-codoping ions is y=0.2. The results imply that the Ca_2.95−yDy_0.05B₂O₆:yNa⁺ phosphors could be potentially used as white LEDs.     

Y2O3:Yb3+,Tm3+纳米材料的可见及紫外上转换发光

通过燃烧法制备了Yb³⁺-Tm³⁺共掺的Y₂O₃纳米粉体,并对样品在980 nm激光照射下的上转换发光特性进行了研究.实验发现,样品在可见光区域能够产生强烈的蓝色发光(476 nm和487 nm)和较弱的红色发光(约650 nm),而且同时观察到了两个紫外发光峰¹I₆→³H₆ (~297 nm)和^{1关键词： 2O₃:Yb3+')" href="#">Y₂O₃:Yb3+ 3+}')" href="#">Tm³⁺ 上转换光谱 敏化 紫外发光     

Dielectric properties and temperature stability of BaTiO3 co-doped La2O3 and Tm2O3

The influence of La₂O₃ and Tm₂O₃ co-doping on the dielectric properties and the temperature stability of BaTiO₃ was investigated. BaTiO₃ ceramics were prepared with the compositional formula of (Ba_1−xLa_x)(Ti_1-x/4−yTm_y)O₃. La₂O₃ and Tm₂O₃ co-doping in BaTiO₃ mainly had effects on an increase in the dielectric constant and the temperature stability, respectively. The increase of La₂O₃ concentration and the decrease of Tm₂O₃ concentration in BaTiO₃ resulted in a decrease of lattice parameter and tetragonality because La³⁺ ion substituting for Ba site is smaller than Ba²⁺ ion and Tm³⁺ ion substituting for Ti site is larger than Ti⁴⁺ ion. With the increase of La₂O₃ and the decrease of Tm₂O₃, the dielectric constant of BaTiO₃ was enhanced in spite of the reduction of tetragonality. P-E hysteresis measurements revealed that this phenomenon was based on the improvement of remanent polarization with the increase of La₂O₃ concentration. The introduction of excess Tm₂O₃ in BaTiO₃ suppressed the grain growth and BaTiO₃ ceramics showed higher temperature stability due to the stable tetragonal structure and the small grain size with the increase of Tm₂O₃ concentration.     

Effects of RE2O3 (RE = Tm, Sc, Yb) addition on the superconducting properties of ErBa2Cu3Oy

We investigated the effects of added Tm₂O₃, Sc₂O₃, and Yb₂O₃ on the superconducting properties of sintered Er123 samples. Tm₂O₃ addition caused the least T_c degradation, exhibiting a T_c above 90 K even for 17 vol% addition. Samples with added Sc₂O₃ maintained a T_c at above 90 K up to an addition of 7.2 vol%, while Yb₂O₃-containing samples showed a monotonic decrease in T_c with increased vol% of added Yb₂O₃. Tm₂O₃-containing samples exhibited a slight increase in J_c(0.1 T)/J_c(0) and had constant J_c values even for 17 vol% addition. XRD and SEM results indicate that the Tm₂O₃ is very stable in the superconducting matrix.     

Efficient blue upconversion emission due to confined radiative energy transfer in Tm-Nd co-doped Ta2O5 waveguides under infrared-laser excitation

Intense blue upconversion emission at 480 nm has been obtained at room temperature in Tm³⁺-Nd³⁺ co-doped Ta₂O₅ channel waveguides fabricated on a Si substrate, when the sample is excited with an infrared laser at 793 nm. The upconversion mechanism is based on the radiative relaxation of the Nd³⁺ ions (⁴F_3/2 → ⁴I_11/2) at about 1064 nm followed by the absorption of the emitted photons by Tm³⁺ ions in the ³H₄ excited state. A coefficient of energy transfer rate as high as 3 × 10⁻¹⁶ cm³/s has been deduced using a rate equation analysis, which is the highest reported for Tm-Nd co-doped systems. The confinement of the 1064 nm emitted radiation in the waveguide structure is the main reason of the high energy transfer probability between Nd³⁺ and Tm³⁺ ions.     

Tm2O3相对于Si的能带偏移研究

利用分子束外延系统在Si (001) 衬底上制备了单晶Tm₂O₃薄膜, 利用X射线光电子能谱研究了Tm₂O₃相对于Si的能带偏移. 得出Tm₂O₃相对于Si的价带和导带偏移分别为3.1 eV± 0.2 eV和1.9 eV± 0.3 eV, 并得出了Tm₂O₃的禁带宽度为6.1 eV± 0.2 eV. 研究结果表明Tm₂O₃是一种很有前途的高k栅介质候选材料. 关键词： 2O₃')" href="#">Tm₂O₃ X射线光电子能谱 能带偏移     

Tm3+/Yb3+共掺碲酸盐玻璃的近红外发光及能量传递机理

采用高温熔融法制备了组分为TeO₂-ZnO-Na₂O的Tm³⁺离子单掺和Tm³⁺/Yb³⁺共掺碲酸盐玻璃,应用Judd-Ofelt理论计算分析了玻璃样品的强度参量Ω_t(t=2, 4, 6),自发辐射跃迁几率A,荧光分支比β和荧光辐射寿命τ_rad等光谱参量,测量得到了不同Yb³⁺离子掺杂浓度下玻璃样品的Tm³⁺离子上转换发光谱.结果显示,在980 nm泵浦光激励下玻璃样品发射出强烈的近红外上转换荧光.对Tm³⁺离子上转换发光分析表明,强烈的Tm³⁺离子近红外上转换发光主要来自于Yb³⁺/Yb³⁺离子间的共振能量传递以及基于单声子和双声子辅助的Yb³⁺/Tm³⁺离子间的非共振能量传递过程,并进一步计算得到了声子贡献比和能量传递系数.最后,计算分析了Tm³⁺:³F₄→³H₆能级间跃迁的1.8 μm波段吸收截面、受激发射截面和增益系数.研究表明,Yb³⁺/Tm³⁺共掺TeO₂-ZnO-Na₂O玻璃可以作为近红外波段固体激光器的潜在增益基质.     

Tm3+/Ho3+共掺镓铋酸盐玻璃1.47μm发光特性和能量传递的研究

报道了Tm³⁺/Ho³⁺共掺的镓铋酸盐玻璃14Ga₂O₃-25Bi₂O₃-20GeO₂-31PbO-10PbF₂玻璃1.47μm(S波段)发光和能量传递特征，应用Judd-Ofelt理论计算了玻璃的强度参数Ω_t(t=2，4，6)，自发辐射概率A、荧光分支比β，荧光辐射寿命τ等各项光谱参数以及有效荧光线宽Δλ_eff和峰值发射截面σ^peak_e.通过测量荧光光谱和荧光寿命研究了Ho³⁺离子掺杂浓度对Tm³⁺离子1.47μm波段发光性能的影响，分析了Tm³⁺和Ho³⁺之间的能量传递过程.结果表明一定浓度内Ho³⁺的共掺迅速降低了Tm³⁺：³F₄能级的粒子数，而对³H₄能级粒子数影响不大，从而降低了³F₄和³H₄能级间布居数反转的难度，极大地提高了1.47μm发光效率.研究表明镓铋酸盐玻璃是适用于S波段光纤放大器的一种潜在基质材料，而掺杂一定浓度的Ho³⁺离子有利于提高Tm³⁺离子在1.47μm波段的发光效率. 关键词： 重金属氧化物玻璃 光谱性质 3+/Ho³⁺离子')" href="#">Tm³⁺/Ho³⁺离子 能量传递     

Infrared-to-Ultraviolet upconversion luminescence of La0.95Yb0.49Tm0.01F3 nanostructures

In this work, we used the hydrothermal method to synthesize Yb³⁺ and Tm³⁺ doped LaF₃ nanostructures, which is an ultraviolet upconversion luminescent material. Two distinct shapes such as nanosheets, nanoparticles and bulk samples formed in the products by adjusting the concentrations of the surfactant of the reaction solution. Powder X-ray diffraction analysis showed that the products were pure hexagonal phase, while electron microscopy measurements confirm the formation of different morphologies. These nanostructures exhibit strong ultraviolet upconversion luminescence under the excitation of a 978-nm diode laser. In Yb³⁺ and Tm³⁺ codoped LaF₃ materials, the relative intensity of ultraviolet and blue upconversion emissions became stronger as the size and morphology of sample changed from bulk to sheets.