Electrical conductivity and structural stability of SrCo1−xFexO3−δ

Perovskite compounds in the system of SrCo_1−xFe_xO_3−δ (x=0.2, 0.4 and 0.6) were synthesized by solid state reaction. SrCo_1−xFe_xO_3−δ shows the p-type small polaron conduction behavior. Electrical conductivity and oxygen vacancy content decrease with increase in Fe content. The incorporation of Fe increases the structural stability of SrCo_1−xFe_xO_3−δ at low temperatures, while decreasing the structural stability at high temperatures. Oxygen partial pressure has a strong influence on electrical conductivity. At low oxygen partial pressure, SrCo_0.8Fe_0.2O_3−δ will transform from cubic to orthorhombic structure. This structure can remain in 5%H₂/Ar only for a short time and then dissociates into Sr₃Fe₂O_6.64 and Co due to the reduction of B-site elements.     

Manifestation of vortex depinning transition in nonlinear current-voltage characteristics of polycrystalline superconductor Y1−xPrxBa2Cu3O7−δ

We present our recent results on the temperature dependence of current-voltage characteristics for polycrystalline Y_1−xPr_xBa₂Cu₃O_7−δ superconductors with x=0.0, 0.1 and 0.3. The experimental results are found to be reasonably well fitted for all samples by a power like law of the form V=R(I−Ic)^a(T). Here, we assume that a(T)=1+Φ₀IC(T)/2πkBT and IC(T)=IC(0)(1−T/TC)^3/2 for the temperature dependences of the power exponent and critical current, respectively. According to the theoretical interpretation of the obtained results, nonlinear deviation of our current-voltage characteristics curves from Ohmic behavior (with a(TC)=1) below TC is attributed to the manifestation of dissipation processes. They have a characteristic temperature Tp defined via the power exponent as a(Tp)=2 and are related to the current induced depinning of Abrikosov vortices. Both TC(x) and Tp(x) are found to decrease with an increase of Pr concentration x reflecting deterioration of the superconducting properties of the doped samples.     

Co-L3 X-ray absorption near-edge structure analysis of Pr1−xCaxCoO3−δ and Pr1−xSrxCoO3−δ

The valence state of Co ions in Pr_1−xCa_xCoO_3−δ and Pr_1−xSr_xCoO_3−δ has been investigated by an analysis of the Co-L₃ X-ray absorption near-edge structure (XANES) profile. The observed intensity distributions of Co-L₃ XANES change continuously with increasing concentration of alkaline-earth ions. To investigate the origin of this change in the XANES profile, charge transfer multiplet calculations were carried out, which could successfully explain the change in the spectral profile; they also suggest that the valence state of Co ions in Pr_1−xCa_xCoO_3−δ and Pr_1−xSr_xCoO_3−δ is between 3+ and 4+ and increases gradually with the concentration of alkaline-earth ions.     

Structure and magnetism in Ho1−xSrxCoO3−δ

We have magnetically and structurally characterized the Ho_1−xSr_xCoO_3−δ family of materials where 0.67≤x≤0.95. The solid solution range and evolution of the structure as a function of x is established and correlated with the broad range of magnetic behavior observed. The structure is shown to be tetragonal I4/mmm although is possibly cubic when x=0.95. For 0.67≤x≤0.9 the material shows antiferromagnetic long range order and ferromagnetic clusters. At x=0.95 the magnetic transition is at 120 K and the imaginary susceptibility becomes non-zero and the temperature of the cusp in the ac susceptibility shows a frequency dependence indicative of glassiness.     

Effect of Ar+ irradiation on the electrical conductivity of BaCe0.9Y0.1O3−δ

The effects of 10 keV Ar⁺ ion irradiation on the electrical characteristics of BaCe_0.9Y_0.1O_2.95 subject to fluences of 0, 1.0 × 10¹⁷, 5.0 × 10¹⁷ and 1.0 × 10¹⁸ ions/cm² at room temperature, has been investigated using elastic recoil detection analysis (ERDA), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX), X-ray photoelectron spectroscopy (XPS) and alternating current (AC) impedance measurements. It was confirmed from the ERDA results that the hydrogen concentration near the surface increased with increase of Ar⁺ ion fluence. This increase may be associated with the increasing quantities of hydrogen generated by interaction between oxygen vacancies, formed by irradiation, and H₂O from exposure to air. SEM images showed clearly that the number of surface defects due to modification increased with increasing fluence. In addition, the size of the defects showed a tendency to increase with increasing fluence. From the results of XPS analyses, providing information on the electronic states on the surface, it was evident that with increase in the Ar⁺ ion fluence, the quantity of excess oxygen, such as hydroxide, increased in the oxygen 1s XPS spectrum. In addition, it was indirectly found, from decomposition of the Ce 3d, spectrum that the concentration of oxygen vacancies increased with fluence, since the percentage of Ce³⁺ also increased. Accordingly, the surface modification led to the formation of more oxygen vacancies and a greater hydrogen concentration on the surface, since the H₂O interacted with some of them. From the results of the DC conductivity and AC impedance measurements, the proton conductivity was shown to predominate over the temperature range from 473 K to 823 K. It was concluded that the increase in these protons and vacancies generated from surface modification contributed to the increase of proton conductivity.     

High temperature transport and thermoelectric properties of Ca3−xErxCo4O9+δ

Ca_3−xEr_xCo₄O_9+δ (x=0, 0.05, 0.15, 0.3 and 0.5) samples were prepared using a sol-gel method followed by hot-pressing sintering technique. Powder X-ray diffraction analysis showed the single-phases of Ca_3−xEr_xCo₄O_9+δ were obtained up to x=0.3 and the crystallinity of the samples decreased with increasing Er-doping amount. The high-temperature (323-1073 K) thermoelectric properties of the samples were investigated. The substitution of Er³⁺ for Ca²⁺ resulted in the decrease of electrical conductivity, thermal conductivity and the increase of Seebeck coefficient for all the samples except the x=0.05 one. The dimensionless figure of merit ZT reached 0.28 at 1073 K for Ca_2.7Er_0.3Co₄O_9+δ, indicating the thermoelectric properties of CaCo₄O_9+δ can be enhanced by doping Er in the system.     

Epitaxial growth of YSZ buffer layer for YBa2Cu3O7−δ coated conductor by reel-to-reel pulsed laser deposition

Yttria-stabilized zirconia (YSZ) buffer layers were deposited on CeO₂ buffered biaxially textured Ni-W substrate by reel-to-reel pulsed laser deposition (PLD) for the application of YBa₂Cu₃O_7−δ (YBCO) coated conductor and the influence of substrate temperature and laser energy on their crystallinity and microstructure were studied. YSZ thin films were prepared with substrate temperature ranging from 600 to 800 °C and laser energy ranging from 120 to 350 mJ. X-ray diffraction (XRD), scanning electron microscopy (SEM), and atomic force microscopy (AFM) were used to investigate how thin film structure and surface morphology depend on these parameters. It was found that the YSZ films grown at substrate temperature below 600 °C or laser energy above 300 mJ showed amorphous phase, the (0 0 1) preferred orientation and the crystallinity of the YSZ films were improved with increasing the temperature, but the surface roughness increased simultaneously, the SEM images of YSZ films on CeO₂/NiW tapes showed surface morphologies without micro-cracks. Based on these results, we developed the epitaxial PLD-YSZ buffer layer process at the tape transfer speed of 3-4 m/h by the reel-to-reel system for 100 m class long YBCO tapes.     

Investigation on cation distribution and magnetic properties in self-doped manganites La0.6−xSr0.4MnO3−δ

Self-doped manganites with nominal composition La_0.6−xSr_0.4MnO_3−δ (0≤x≤0.175) have been prepared by the sol–gel method. The X-ray diffraction (XRD) patterns and magnetic measurements indicate that the samples have two phases with the ABO₃ perovskite structure being the dominant phase and Mn₃O₄ being the minor phase when the doping level x≥0.05. On the basis of the thermal equilibrium theory of crystal defects, the contents of various ions in the perovskite phases were estimated, in which there are Mn²⁺ ions and no vacancies at A sites. The ion contents have been corrected by Rietveld fitting of the powder samples' X-ray diffraction data. The change tendency of the Curie temperature T_C vs. the Mn⁴⁺ ion content ratio at the B sites of ABO₃ perovskite phase is in accord with the experimental result of the samples La_1−xSr_xMnO₃.     

Studies on sintering of solid state synthesized Ba1−xKxBiO3−δ superconducting phase

Superconducting Ba_1−xK_xBiO_3−δ pellets were synthesized by solid state reaction followed by sintering. Thermo-gravimetric and differential thermo-gravimetric analysis (TG-DTA) of the mixture of nitrates was carried out to study the reactions during the phase formation. The effect of different sintering temperatures on the phase formation was studied. The X-ray diffraction data confirms the formation of superconducting Ba_0.6K_0.4BiO_2.23 phase at 700 °C. The surface morphological studies as a function of sintering temperature were studied by SEM. It is observed that the pellets prepared by solid state reaction followed its sintering at 700°C shows the superconducting transition at 26.8 K.     

Structural and magnetic properties in the self-doped perovskite manganites with nominal composition La0.7Sr0.3−xMnO3−δ

Perovskite manganites with nominal composition La_0.7Sr_0.3−xMnO_3−δ (0.00≤x≤0.20) have been prepared by the sol-gel method with the highest heat treatment temperature being 1073 K. The XRD patterns indicate that when the doping level is x≤0.10 the samples have only a single phase, with the R3?c perovskite structure, while for x>0.10, the samples have two phases with the R3?c perovskite being the dominant phase and Mn₃O₄ being the second phase. A quantitative analysis and Rietveld fitting of the X-ray powder diffraction data indicate that on the basis of the thermal equilibrium theory of crystal defects there are Mn²⁺ ions at the A sites and Mn³⁺ plus Mn⁴⁺ ions at the B sites in the ABO₃ perovskite phase. The curves of magnetization versus applied magnetic field at 10 K showed that the magnetic moments of the Mn²⁺ ions at the A sites are antiparallel to those of the Mn³⁺ and Mn⁴⁺ ions at the B sites.     

Relaxation of the normal electrical resistivity induced by high-pressure in strongly underdoped YBa2Cu3O7–δ single crystals

We investigate the relaxation of the normal electrical resistivity, induced by high-pressure in YBa₂Cu₃O_6.45 single crystals. It is determined that the pressure affects to the phase composition of the sample. Under pressure phases with different (but similar) critical temperatures form. It is determined that the application-removal pressure process is completely reversible. Above T_c the temperature dependence of the resistivity in the layers' plane at different hydrostatic pressures can be approximated with high accuracy with the scattering of electrons by phonons model. With increasing pressure, the residual resistance is reduced and the contribution of intraband s–s scattering increases. Additionally, the role of the interband s–d scattering and the Debye temperature is enhanced.     

Influence of the substrate material on the properties of pulsed laser deposited thin Li1+xMn2O4−δ films

Thin Li_1+xMn₂O_4−δ films were deposited on several substrate materials (stainless steel, p-doped silicon and glassy carbon) by pulsed laser deposition. To obtain the correct thin film stoichiometries, targets with a different amount of excess lithium were required (Li_1.03Mn₂O₄ + xLi₂O; x = 2.5 and 7.5 mol%). The resulting polycrystalline thin films were characterized with respect to their morphology and electrochemical activity. It was found that only thin Li_1+xMn₂O_4−δ films deposited on stainless steel and glassy carbon showed the typical insertion and deinsertion peaks of Li⁺ during cycling.     

Si doped Cu0.5Tl0.5Ba2Ca2Cu3O10−δ superconductors

The Si doped (Cu_0.5Tl_0.5)Ba₂Ca₂Cu_3−ySi_yO_10−δ (y=0, 0.25, 0.5, 0.75, 1.0, 1.25) superconductor samples have been synthesized to investigate the effect of mobile carriers on the critical temperature and magnitude of diamagnetism of this family of cuprates. The Si doped samples have tetragonal structure as observed from the X-ray diffraction spectra. The c-axis length of the unit cell of (Cu_0.5Tl_0.5)Ba₂Ca₂Cu_3−ySi_yO_10−δ was increased after the increase of Si concentration, whereas the critical temperature and the magnitude of diamagnetism have been decreased. The decrease in T_c(0) and magnitude of diamagnetism is possibly due to the deficiency of carriers in CuO₂/SiO₂ planes caused by the +4 state of Si atoms. However, the post-annealing of these samples in oxygen atmosphere has increased the critical temperature and the magnitude of diamagnetism. The FTIR absorption measurements of (Cu_0.5Tl_0.5)Ba₂Ca₂Cu_3−ySi_yO_10−δ samples have shown a softening of the apical oxygen mode of the type Cu(1)O_ACu(2) and TlO_ACu(2) with increased concentration of Si in the unit cell; the softening of this mode is directly linked with the increase in the c-axis lattice parameter of the (Cu_0.5Tl_0.5)Ba₂Ca₂Cu_3−ySi_yO_10−δ superconductor.     

The effect of La-substitution on magnetic properties of nanosized Sr1−xLaxTi0.05Zn0.2(Fe)11.75−δ(Fe)δO19 powders

A series of La-substituted M-type Sr hexaferrite powders Sr_1−xLa_xTi_0.05Zn_0.2Fe³⁺_11.75O₁₉, wherein x ranges from 0.1 to 0.5 with a step of 0.1, have been prepared by the conventional ceramic method and were then milled in a high energy mill to prepare nanosized powders. XRD investigation of the calcined and the milled powders shows that single phase hexaferrite structure has been formed after calcining and has not changed after milling. The lattice parameters and the mean crystallite sizes of the samples have been determined from the XRD data and Scherrer's formula. The results show that the lattice parameters (“а” and “c”) decrease with increase in La-substitution and the mean crystallite size of the milled powders is about 17 nm. Coercivities and magnetizations of the samples in a magnetic field of 16 kOe have been determined from the room temperature hysteresis loops. It was found that both parameters increase with La substitutions up to 0.3 and then decrease for higher substitutions. These variations were attributed to the enhancement of hyperfine field and spin-canting magnetic structure when La content increases. In addition, the magnetizations were smaller for the nanosized samples in comparison with those of bulk ones, which were discussed according to the core-shell model. Also the results show that annealing of the nanosized samples up to 500 °C can enhance coercivity and magnetization of the samples, which is discussed based on crystallite size growth.     

STUDY OF HALOGEN DOPING IN POLYCRYSTALLINE YBa2Cu3O7-δ

This paper presents systematically the doping effects of halogens in YBa₂Cu₃O_7-δ polycrystalline samples, with a series of concentrations of fluorine, chlorine, bromine or iodine. All samples were prepared by chemical method of citrate pyrolysis, which makes the halogen concentration in the samples more uniform. Samples doped with F have T_c as high as 94.5K, Cl, Br and I dopings also raise T_c to a certain extent. In addition, the influence of halogen doping on critical current density, morphology, constitution and so forth is discussed.     

YBa2Cu3O7-δ薄膜热激发磁通蠕动研究

本文选择两块零电阻温度分别为82K和71K超导性能不同的薄膜样品,同步进行了电阻在外磁场中展宽的测量,并用Palstra所提出的Arrhenius定律研究两样品热激活能的差别。实验发现样品热激活能随磁场增加线性下降。由测量结果推出的不可逆线仍有B^*-(1-T^*/T_c)^3/2形式。 关键词：     

Glassy carbon - A promising substrate material for pulsed laser deposition of thin Li1+xMn2O4−δ electrodes

The spinel LiMn₂O₄ is a promising candidate for future battery applications. If used as a positive electrode in a battery, the charging capacity of such a battery element is limited by the formation of a solid electrolyte interphase like layer between the electrolyte and the spinel. To study the electrolyte-electrode interaction during electrochemical cycling, spinel thin films are deposited as model electrodes on glassy carbon substrates by pulsed laser ablation. The obtained polycrystalline oxide thin films show a well defined surface morphology and are electrochemical active. Adhesion of these thin films on glassy carbon is in general poor, but can be improved considerably by a surface pretreatment or adding a thin metallic coating to the substrate prior deposition. The best adhesion is obtained for films deposited on argon plasma pretreated as well as Pt coated glassy carbon substrates. During the electrochemical characterization of Li_1.06Mn₂O_3.8 thin film electrodes, no additional reactions of the substrate are observed independent of the used electrolyte. The best cycle stability is achieved for films on Pt coated glassy carbon substrates.     

Structural investigation of the BaSnO3–YBa2Cu3O7−x system

We report the microstructure change of BaSnO₃ (BSO)–YBa₂Cu₃O_7−x (YBCO) thin film system grown on SrTiO₃ single crystal substrates by pulsed laser deposition with using the “surface-modified-target” and “mixture-target” methods. Although it was confirmed that the thick BSO nanorods incorporated to YBCO films act as strong artificial pinning centers, the formation mechanism of the nanorods is still unclear. The purpose of this work is to extend the structural investigation to higher contents of BSO (up to 71 vol.%) in order to enlighten the relationship among interfacial energy, morphology and pinning performance in binary BSO–YBCO films.     

IRREVERSIBILITY LINE AND THERMAL DEPINNING IN YBa2Cu3O7-δ

By measuring magnetic torque moment in a field-sweeping process, the temperature and field dependence of the critical current density j (with a criterion of electric field) and the normalized relaxation rate Q = d lnj/d ln E of a YBa₂Cu₃O_7-δ thin film were obtained. With a minimum current density (j_min = 10A·cm^-2) the irreversibility lines at different sweeping rates were determined. It was found that these irreversibility lines cannot be fitted to either the melting line or the vortex-glass transition. All the data can be interpreted by the thermally-assisted-flux-flow model. Further investigation shows that, at irreversible tem-perature and field, U_c is much smaller than k_BT, which indicates that the thermal depinning is the real origin of the irreversibility line.