明胶基多孔碳球电极材料的制备及电化学性能研究

Gelatin-based porous carbon beads have been fabricated from gelatin micro-spheres by means of solidification, carbonization and chemical activation with KOH. The physical properties of gelatin-based porous carbon beads were studied by a t-plot method based on N₂ adsorption isotherms. The gelatin-based porous carbon beads activated at 800 ℃ exhibited the largest specific surface area and resulted in the highest capacitance. Carbon/carbon super-capacitors cells assembled with the electrode materials in 1.0 mol·L^-1 NEt₄BF₄ / acetonitrile electrolyte have also been studied. The electrochemical properties of gelatin-based porous carbon beads electrode were studied by using constant-current discharge tests. The results indicate that the gelatin-based porous carbon beads electrode is with good cycling stability and specific capacitance of 119.8 F·g^-1.     

一种估算多壁碳纳米管电化学容量的方法

Five kinds of multi-walled carbon nanotubes were prepared by CVD(Chemical Vapour Deposition) and purified under the same conditions, then were used as electrodes for super capacitors in order to compare their performance. The differences measured in terms of specific capacitance by galvanostatic cycling were presented, porosity measurements using nitrogen at 77 K made on carbon nanotubes allowd a better understanding of the electrochemical behavior of these carbon nanotubes. The experiment results show that pore diameter in the range of more than 3nm is required to maximize the capacitance in the electrolyte of 1.0 mol·L^-1 LiClO₄/EC+DEC(V_EC∶V_DEC=1∶1), and the BET surface area contributed by this extent is almost linear with the specific capacitance, in which an average value is about 0.11 F·m^-2, and the specific capacitance estimated from above is very close to the value by experiment.     

碳化硅为载体的氨合成催化剂的制备及性能研究

A sol-gel process catalyzed by oxalic acid was used for the preparation of SiC precursor from raw materials of tetraethyl orthosilicate (TEOS) and sucrose. The precursor thus obtained was homogeneous. Sintered with a certain heating program in an argon flow, the precursor was converted into the high surface area SiC. The high specific surface area silicon carbide was used as catalyst support for ammonia synthesis. The effect of the surface of the support, promoter and the amount of Ru on the catalytic activity for ammonia synthesis was studied. The results show that when the high specific surface area SiC of 113 m²·g^-1 is used as support, the prepared SiC-supported ruthenium catalyst has a relatively high activity(11.85%) under Ru 4wt%, Ba 4wt%, K 8wt%, 475 ℃, 10.0 MPa and 10 000 h^-1.     

水热法制备高纯超细CeO2-ZrO2复合氧化物

Superfine composite powders of CeO₂-ZrO₂ (CZ) and CeO₂-ZrO₂-La₂O₃ (CZL) were prepared by hydrothermal method. The effects of pH、temperature and time for hydrothermal process on the performance of the resulting powders were studied. The optimized reaction parameters were on follows: the precursor′s pH≈9.0, hydrothermal temperature of 200 ℃ holding for 2 h. Thermal stable powders with average particle size smaller than 10 nm and specific surface area of 171 m²·g^-1 were obtained. A BET specific surface area was still at 44 m²·g^-1 after calcination at 1 000 ℃ for 6 hours.     

纳米晶构筑一维多孔氧化锌的合成与表征

One-dimensional porous zinc oxide was prepared via the calcination of zinc oxalate precursor obtained by solvothermal method. The products were characterized by XRD, SEM, TEM, photoluminescence (PL) spectrum and nitrogen adsorption-desorption. The results show that the obtained zinc oxide sample is porous and constructed by nanoparticles about 30 nm in size. The specific surface area and total pore volume are 126 m²·g^-1 and 0.13 cm³·g^-1, respectively． The PL properties related with defects in ZnO nanoparticles were discussed for porous zinc oxide samples.     

合成大比表面γ-Mo2N的新方法

The production of high specific surface area γ-Mo₂N (up to 165 m²·g^-1, passivated) by temperature programmed reaction of MoO₃ with mixtures of N₂ and H₂ was reported. The synthetic condition of high surface area γ-Mo₂N (usually, S_BET>100 m²·g^-1) were quite difficult and the amount of starting material MoO₃ in each batch was much less than 0.5 gram. However, some synthetic conditions had been greatly improved in our experiments. The crystalline phase and specific surface area had been characterized by XRD and BET. The XRD gave some information for reaction mechanism.     

硬脂酸法制备超细K2La2Ti3O10及其酸交换性质研究

A new stearic acid method(SAM) has been used to prepare ultrafine K₂La₂Ti₃O₁₀ nanocrystalline. Each state of synthesis process was followed by the use of FT-IR analysis. The resulting materials have been characterized by means of XRD， TEM， BET surface area analysis. The acid-exchanging property of the obtained product was also studied. The experimental results showed that comparing with the product of traditional solid-state reaction， the particle size of the K₂La₂Ti₃O₁₀ synthesized by SAM is greatly reduced， BET surface area is high(more than 11.83m²·g^-1) and has different acid-exchanging properties. It can be easily exfoliated in 2mol·L^-1 HNO₃ so-lution.     

Effect of agitation on removal of acetic acid from pretreated hydrolysate by activated carbon

The effect of agitation on the adsorption of acetic acid by activated carbon was tested utilizing an external mass transfer-diffusion model. Simulated pretreated biomass was contacted with activated carbon under prescribed conditions of temperature and agitation. Adsorption isotherm studies are presented as well as batch kinetic rate studies. Use of these data enabled the determination of isotherm constants, an external mass transfer coefficient, and an effective diffusivity for each agitation rate studied. The external film coefficient results ranged from 33.62 μm/s to a complete absence of external mass transfer resistance, and the diffusivity results ranged from 0.8625 to 10.70 μm²/s. The optimum combination of no external film resistance, and highest diffusivity, 10.70 μm²/s, occurred at 250 rpm and 25°C. The results of these models and the experimental parameters suggested an efficacious method and conditions for the removal of this undesirable chemical.     

纳米晶SnO2粉体的合成

Crystalline tin oxide nanoparticles were synthesized by the direct precipitation from the starting material granulated tin. TG-DTA of the precursor showed a heavy weight loss at about 130℃ accompanied by an endothermic peak， two exothermic peaks above 200℃ accompanied by small weight loss indicated the decomposition and the oxidation of residual NO₃^- ion and PEG. XRD showed that obtained particles agreed well with the determination result of bulk SnO₂. The broadened XRD patterns became sharper as the calcining temperature turned to higher， it was indicated that the growth of the particle was exhibited. The surface area of the particles calcined at 300℃ was 161.1m²·g^-1 and declined as the calcining temperature turned to higher. TEM showed an heavier agglomeration at higher temperature.     

新型纳米多孔SiO2气凝胶微球材料的制备

A new type of nanoporous SiO₂ aerogel microsphere materials were synthesized by using SiO₂ sols as raw materials in the W/O emulsion formed by the emulsification of Tween-85 and Span-80. The obtained wet gel microspheres were aged by a successive solvent exchanging of alcohol, tetraethylorthosilicate (TEOS)/ethanol solution and ethanol at 60 ℃, and then were dried at ambient pressure to produce SiO₂ aerogel microspheres. The resultant SiO₂ aerogel microspheres were characterized by SEM, TEM and nitrogen adsorption-desorption. The results show that the prepared SiO₂ aerogel microspheres are nanoporous materials with coherent network nanoporous structure consisting of SiO₂ nanoparticles with an average diameter of about 10 nm. The apparent density of a typical sample is 0.4 g·cm^-3, while the specific surface area is 386 m²·g^-1, and the average pore size is 18 nm with the porosity of 84%. Various SiO₂ aerogel microspheres with the apparent particle sizes of 10～200 μm can be synthesized by controlling the stirring speed at 600～2 000 r·min^-1, the volume ratio of water/oil from 0.10 to 0.30, and the weight ratio of Tween-85/Span-80 less than 0.40.     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Summary of development of the theory of stability of colloids and thin films

In this review, the research of the author in the field of colloidal systems is summarized. The factors influencing colloidal stability are systematized and analyzed. Examples are presented to illustrate the practical utilization of the theory of stability of colloids and thin films.This review was prepared on the basis of the works of the author, which were awarded the State Premium for 1991 in the field of science and technology, chemistry section.Institute of Physical Chemistry, Russian Academy of Sciences, 117915 Moscow. Translated from Izvestiya Akademii Nauk, Seriya Khimicheskaya, No. 8, pp. 1708–1717, August, 1992.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Thermodynamics of the formation of oxosulfides of rare-earth elements

The enthalpies of solution of several oxosulfides of rare-earth elements and the high-temperature enthalpies of oxosulfides and oxosulfates of lanthanum and yttrium were measured using solution calorimetry and high-temperature microcalorimetry techniques. Standard enthalpies of formation and some thermodynamic properties of oxosulfides and oxosulfates were calculated. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 2 pp. 294–297, February, 1997.     

探究“铁的锈蚀条件”实验创新设计

设计了铁的锈蚀实验,说明了铁钉的处理方法,增加了温度、酸、碱的影响条件,实现了铁跟蒸馏水及空气中氧气快速反应而生锈,使实验在5 min左右就能够得到准确的结果。