超薄Co3O4纳米片薄膜制备及其电化学传感器性能

本文以电沉积的金属钴薄膜作为原材料,通过简单的氧化技术获得了薄膜前驱体材料,并进一步在350 ^oC热处理条件下获得了超薄Co₃O₄纳米片薄膜材料. 通过扫描电镜（SEM）,X-射线衍射（XRD）,透射电镜（TEM）等手段对材料的物理结构进行了深入分析,并通过循环伏安法（CV）表征了该薄膜材料的电化学活性. 作为电化学传感器件的活性材料,该薄膜材料对H₂O₂的检测表现出较宽的线性浓度检测范围（0 ~ 4 mmol•L^-1）和较高的电流响应(~ 1.15 mA•cm^-2),在该领域具有较高的应用价值.     

球形微粒Co3O4电极催化氧化硫离子

尝试用氨蒸发诱导合成方法在石墨小片上生长球形Co₃O₄微粒, 并用其制备电极且进行S^2-的电化学氧化研究. 用极化曲线、恒电位技术等电化学方法考察了Co₃O₄电极对S^2-的电化学氧化的催化性能, 发现Co₃O₄电极对电化学氧化S^2-具有优异的催化性能, 极大地促进了-0.40 V 附近S^2-向含硫的酸根离子和低级多硫离子的转变, 电流密度最大可以达到580 mA·cm^-2. 恒电位极化表明电极的电催化稳定性良好; 电化学阻抗谱(EIS)测试显示Co₃O₄在碱性S^2-电解液中的电荷转移电阻很小, 这从电化学动力学角度解释了它对S^2-具有良好的催化性能.     

Co3O4 纳米棒的溶剂热合成及形成机理分析

Co3O4 nanorods have been synthesized at 160℃ for 10 h in the solution of oleic and n-cetane by an emulsion-solvothermal method using Co（NO3）2·6H2O as starting materials. The as-prepared product was characterized by X-ray powder diffraction（XRD）,transmission electron microscope（TEM）,and vibrating sample magnetometer（VSM）. The formation mechanism of the prepared product was analyzed based on formation of rod-like micelles of oleic acid. Cobalt ions can migrate into the micelle core for the nucleation and growth of Co3O4 . The results show that the as-prepared Co3O4 nanorods are with the average size 25×100 nm and in the cubic phase. The magnetic susceptibility meets about linearly with the applied magnetic field at room temperature,and the coercivity （Hc）and remanent magnetization（Ms）values of the product at room temperature are 353 Oe and 0.4 emu/g,respectively. This simple route is also expanded to synthesize other materials with the rod-like morphology.     

各种形貌的纳米Co3O4的制备及其应用*

本文综述了各种形貌的纳米Co₃O₄的制备及其应用。制备纳米Co₃O₄的方法有很多,包括热分解、水热法、溶剂热法、化学喷雾热分解、化学气相沉积和溶胶-凝胶法。各种形貌的Co₃O₄被制备,如纳米球、纳米立方体、纳米管、纳米棒、纳米片、纳米纤维和介孔结构。Co₃O₄是一种重要的磁性P-型半导体,在锂离子电池、超级电容器、电致变色、磁性材料、气体传感器和催化剂等诸多领域有比较广泛的应用。     

液相控制沉淀法制备纳米级Co3O4微粉

报道了一种液相控制沉淀与分解制备Co₃O₄超微粉的方法.研究表明,采用液相沉淀控制技术,无需引入高分子保护剂,同样可以制备出晶粒细小、粒度分布均匀、无团聚的高质量Co₃O₄超微粉.该法工艺简单、成本低、产率高.     

聚合物燃烧方法制备Co3O4纳米粒子

纳米粒子因其独特的物理化学特性成为近年来材料科学领域的研究热点。制备方法是获得性能优越材料的关键。Co3O4具有正常的尖晶石结构，Co^2 占据八面体位置，在空气中低于800℃时十分稳定，是优良的催化剂材料^[1,2]，采用燃烧方法可通过控制反应条件在不发生沉淀的情况下获得化学组成均匀的复合氧化物粉体^[4-7]，本利用聚合物燃烧方法探索制备粒径均匀，分散性好的立方Co3O4纳米粒子，选择聚乙烯醇（PVA）的原因是其分子内包含大量的羟基极性基团，能与金属离子尤其是过渡金属离子形成良好的化学键，促使金属离子在PVA高分子的网络中均匀螯合分布，有利于最终形成分散性良好的粉体。     

Co3O4纳米立方体的可控合成及其CO氧化反应性能

在乙醇和三乙胺的混合溶液中,采用溶剂热法制备了尺寸为10 nm的Co₃O₄立方体. 考察了钴盐前驱体和溶解氧对Co₃O₄纳米立方体结构的影响规律,通过对合成过程中不同阶段产物的结构分析和表征,提出了Co₃O₄纳米立方体的形成机制是溶解再结晶的过程. 将所制备的Co₃O₄纳米立方体在200 ℃焙烧处理后,尺寸和形貌均可保持稳定,但400 ℃焙烧后,变为球形纳米粒子. 这种主要暴露{100}晶面的Co₃O₄纳米立方体催化CO氧化反应的活性低于纳米粒子({111}晶面),验证了四氧化三钴纳米材料在CO氧化反应中的晶面效应.     

溶剂热法合成不同形貌的Co3O4及其电容特性

采用溶剂热法以不同的钴盐在水-正丁醇体系中合成了不同形貌及尺寸的纳米Co3O4. 采用XRD和TEM对产物的物相和形貌进行表征. 结果表明, 通过改变反应体系中阴离子的种类, 可以控制产物Co3O4的形貌与晶粒尺寸. 通过循环伏安法、恒流充放电和交流阻抗法对Co3O4电极材料的电化学性能进行表征. 结果表明, Co3O4的形貌与晶粒尺寸对其电化学性能有显著影响. 在2 mol·L-1 KOH溶液中, 在-0.40 - 0.55 V (vs SCE)电位范围内, 由Co(NO3)2制备的球形Co3O4表现出更好的电容特性,单电极初始比容量达362.0 F·g-1, 经过400 次循环后比容量仍保持90%.     

丙三醇辅助水热法合成纳米棒状LiFePO4

在丙三醇存在下,以FeSO4·7H2O,LiOH·H2O和H3 PO4为原料,采用水热法合成了橄榄石结构的纳米棒状LiFePO4.产物结构与形貌用X射线衍射、红外、扫描电子显微镜、能谱分析测试技术进行了表征.讨论了反应时间、温度、混合溶剂比例对产品形貌的影响.结果表明,当V(水)/以丙三醇)=2:1时,在180℃反应2...     

不同维度Co3O4纳米材料的水热合成研究进展

过渡金属氧化物Co_3O_4的晶体结构及表面特性与其形貌、尺寸和微观结构密切相关。本文将不同形貌Co_3O_4纳米材料按尺寸分为:纳米球、立方块、多面体等零维材料,纳米线、纳米棒、纳米管、纳米柱等1D材料,纳米片、纳米薄膜等2D材料,海胆状、微米球等由纳米单元构成的微米尺寸3D超结构。探讨了对形貌形成的影响因素,重点研究其水热合成过程,总结了可能的形成机理,以利于对不同维度材料的形成规律有较深入的理解,进而能在理论上指导特定维度、特定形貌材料的可控合成。     

Urchin-like Co3O4 Nanostructure and Their Electrochemical Behavior in Rechargeable Lithium Ion Battery

3D urchin-like Co₃O₄ have been successfully prepared by calcination of the urchin-like pre-cursors, which were synthesized through a facile hydrothermal route. The morphology and structure of the 3D urchin-like Co₃O₄ have been characterized by field emission scanning electron microscopy, transmission electron microscopy, high resolution transmission elec-tron microscopy, and X-ray powder diffraction. The as-synthesized Co₃O₄ products are of urchin-like structures with approximated 5-7 μm in diameter, and are composed of numer-ous nanoparticles chains with the particles diameter of about 15 nm. This kind of urchin-like Co₃O₄ exhibits superior energy storage properties with the high capacity of 1.369 Ah/g and its good cyclic stability shows great potential in the rechargeable Li-ion battery.     

Catalytic decomposition of H2O2 on Co3O4 doped with MgO and V2O5

The effects of doping of Co₃O₄with MgO (0.4–6 mol%) and V₂O₅ (0.20–0.75 mol%) on its surface and catalytic properties were investigated using nitrogen adsorption at −196°C and decomposition of H₂O₂ at 30–50°C. Pure and doped samples were prepared by thermal decomposition in air at 500–900°C, of pure basic cobalt carbonate and basic carbonate treated with different proportions of magnesium nitrate and ammonium vanadate. The results revealed that, V₂O₅ doping followed by precalcination at 500–900°C did not much modify the specific surface area of the treated Co₃O₄ solid. Treatment of Co₃O₄ with MgO at 500–900°C resulted in a significant increase in the specific surface area of cobaltic oxide. The catalytic activity in H₂O₂ decomposition, of Co₃O₄ was found to suffer a considerable increase by treatment with MgO. The maximum increase in the catalytic reaction rate constant (k) measured at 40°C on Co₃O₄ due to doping with 3 mol% MgO attained 218, 590 and 275% for the catalysts precalcined at 500, 700 and 900°C, respectively. V₂O₅-doping of Co₃O₄ brought about a significant progressive decrease in its catalytic activity. The maximum decrease in the reaction rate constant measured at 40°C over the 0.75 mol% V₂O₅-doped Co₃O₄ solid attained 68 and 93% for the catalyst samples precalcined at 500 and 900°C, respectively. The doping process did not modify the activation energy of the catalyzed reaction but much modified the concentration of catalytically active constituents without changing their energetic nature. MgO-doping increased the concentration of CO³⁺–CO²⁺ ion pairs and created Mg²⁺–CO³⁺ ion pairs increasing thus the number of active constituents involved in the catalytic decomposition of H₂O₂. V₂O₅-doping exerted an opposite effect via decreasing the number of CO³⁺–CO²⁺ ion pairs besides the possible formation of cobalt vanadate.     

Electrochemical non-enzymatic glucose sensors based on nano-composite of Co3O4 and multiwalled carbon nanotube

Nanocomposite of Co₃O₄ and MCNT was synthesised using one step solvothermal method, and an electrochemical non-enzymatic glucose sensor (Co₃O₄-MCNT/GCE) was successfully constructed. This sensor was used successfully for the quantitative analysis of trace glucose in serum sample.     

Ag复合(Ca0.9Yb0.1)3Co4O9陶瓷的制备及其热电性能

热电材料是利用固体内部载流子输运实现热能和电能直接相互转换的功能材料.     

Co3O4/CeO2 CO氧化的原位红外光谱研究

采用沉淀氧化法制备了Co₃O₄/CeO₂催化剂。分别在干、湿条件下进行了一氧化碳氧化反应研究。运用FT-IR表征手段,在钴铈复合氧化物上进行了CO吸附及CO/O₂共吸附研究。结果表明,与纯的Co₃O₄样品相比,Co₃O₄/CeO₂具有明显的抗湿气能力。Co₃O₄/CeO₂催化剂在进行CO氧化时,表面形成了类碳酸盐物种。当环境温度低于453 K时,催化剂上类碳酸盐的生成与形成类碳酸盐物种后受热分解存在着动态平衡。当环境温度高于493 K,催化剂上生成的类碳酸盐物全部受热分解。氧化铈的加入提高了催化剂的抗湿气性能。较小粒径的Co₃O₄与CeO₂产生的强相互作用可使CeO₂向Co₃O₄提供氧,因而间接提供了CO氧化需要的氧。     

CoBx/Co3O4电催化剂的制备及其氧析出性能

采用NaBH4溶液处理经水热、热处理步骤制得Co3O4纳米棒,得到表面富含氧空位以及无定型CoBx的Co3O4(CoBx/Co3O4)氧析出(OER)电催化剂。利用X射线衍射(XRD)、场发射扫描电镜(FESEM)、透射电镜(TEM)、X射线光电子能谱仪(XPS)等技术表征了催化剂的物相、微观形貌、元素组成以及表面化学键结构等。通过电化学工作站测试了电极材料的OER活性、稳定性、电化学阻抗等。结果表明,经NaBH4处理后,Co3O4表面高价态Co被还原至低价态Co,最终其表面有无定型CoBx的生成,并含有大量氧空位,有效提升了OER性能。在1.0 mol·L^-1 KOH电解质溶液中,达到10 mA·cm^-2的电流密度时,CoBx/Co3O4所需的过电位由Co3O4的346 mV降至298 mV。     

多层多孔Co3O4纳米粒子组装体的合成、表征和电化学性能研究

利用十二烷基磺酸钠(SDS)作为表面活性剂,合成了形貌化的CoC₂O₄配合物前驱物,然后在500 ℃下热分解形貌化的前驱物,得到了多层多孔Co₃O₄纳米粒子组装体。采用FESEM、TEM、HRTEM、XRD、N₂吸附脱附和Raman散射等手段对产物进行了分析和表征。低角XRD,TEM和N₂吸附脱附测试表明所得组装体具有多孔结构。常规XRD、HRTEM和Raman结果证明组装体中Co₃O₄纳米粒子建筑块结晶较好。与体相Co₃O₄晶体相比,Co₃O₄纳米粒子组装体的5个拉曼活性峰发生了明显的红移。将Co₃O₄纳米粒子组装体作为锂离子电池的正极材料进行了电化学性能测试,结果表明该组装体电极的首次放电容量为1 115 mAh·g^-1,远高于目前文献报道的Co₃O₄纳米管、纳米粒子和纳米棒电极。但是,该组装体电极的循环性能不好,有待进一步提高。     

Low-temperature and stable CO oxidation of Co3O4/TiO2 monolithic catalysts

Highly efficient Co₃O₄/TiO₂ monolithic catalysts with enhanced stability were in-situ grown on Ti mesh for CO oxidation,which could completely oxidize CO at 120℃.The comprehensive catalytic performance is competitive to some noble metal catalysts and conventional Co₃O₄ powder catalysts,which holds great potential toward industrial applications.Meanwhile,the in-situ synthesis strategy of Co₃O₄/TiO₂ monolithic catalysts on flexible mesh substrate in this work can be extended to the development of a variety of oxide-based monolithic catalysts towards diverse catalysis applications.     

Co3O4空心球的简易合成及其电化学性能

通过简易的水热法"一锅"制备了Co3O4空心球。借助X射线衍射仪(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)和傅里叶变换红外光谱法(FTIR)等对Co3O4的结构和形貌进行了表征。结果表明,产物由Co3O4纳米粒子构成,并形成明显的空心多孔结构。循环伏安法(CV)测试表明,所制得的Co3O4空心球呈现良好的电化学性能。本文同时对Co3O4空心球结构的形成过程和可能的机理进行了分析和讨论。     

还原-氧化预处理对Co_3O_4催化分解N_2O性能的影响

采用液相沉淀法制备了Co_3O_4催化剂,并对其进行还原-氧化预处理制得Co_3O_4-RO。通过XRD、N_2-physisorption、Raman、H_2-TPR、XPS和O_2-TPD等技术对催化剂进行表征,在连续流动微反应装置上考察了催化剂催化分解N_2O性能。结果表明,经过还原-氧化预处理,与Co_3O_4催化剂相比,Co_3O_4-RO结晶度变差,晶粒粒径减小,尤其是尖晶石结构重构过程削弱了Co-O键,增强了催化剂表面的氧物种脱附能力,降低了催化分解N_2O反应的活化能,因而显著提高了催化剂的催化活性。同时,Co_3O_4-RO对原料气中的O_22%(体积分数)和H_2O 2. 3%(体积分数)表现出较强的耐受性。