以ZnO为电子传输层PPV的发光

以Ⅱ-Ⅵ族无机半导体ZnO为电子传输层,PPV为空穴传输层和发光层,得到的电致发光器件比单层PPV器件的发光亮度和效率都高.器件结构为ITO/PPV/ZnO/Al的电致发光光谱同单层PPV器件的光谱基本相同,但是启亮电压明显比单层器件低,最大亮度大约比单层器件高6倍左右,同时工作电流也比单层器件小.通过PPV层自吸收现象可判断出发光区域在PPV/ZnO界面处.电流-电压曲线表明,这种器件具有空间电荷限制电流特性,即J∝Vn,这里n大约为2,这器件的电流主要受到空穴的限制.     

ZnS:Mn、Cu粉末直流电致发光器件直流和交流电致发光一致性的研究

本文研究了粉末直流电致发光(DCEL)器件在直流(DC)和交流(AC)电压下光电特性的关联和区别及其物理机制.实验发现,在DC和AC条件下DCEL器件的阻抗特性之间没有任何有规律的关联,而AC条件下的激发电流IA和亮度BA以及DC条件下的亮度BD和发光效率ηD四个参量之间则表现出某种程度的一致性,但AC条件下的发光效率ηA与上述四个参量之间却表现出某种相反和相对立的关系.DCEL器件的光电特性具有强烈非线性和对电压方向的非对称性.正半周(或DC条件下)DCEL器件是在高电场和低电流激发下的发光.对发光起主要作用的是电场强度.在负半周时则是低电场和大电流激发下的发光.对发光起主要作用的是激发电流而不是电场强度.在AC条件下依材料、工艺、形成条件和工作电压的不同,DCEL器件可能更多地显示出正半周,负半周或两半周综合的光电特性.上述观点可以解释本文的实验结果.     

SiO2/C9-PPV异质结中类阴极射线发光及有机电致发光的交互增强

用夹在两层SiO2之间的发光聚合物C9-PPV作成器件，在交流电激发下得到了超出有机电致发光黄绿色发光的蓝色发光.通过对器件光学特性的研究，发现这种发光源于SiO2中加速电子直接碰撞激发有机发光层而引起的类阴极射线发光.使用非对称结构，得到了类阴极射线发光与有机电致发光相互增强的混合发光. 关键词： 混合发光 类阴极射线发光 有机电致发光     

直流电致发光(DCEL)器件在交流(AC)电压下的I-V,B-V和B-I特性

本文研究了DCEL器件在AC条件下的电流-电压(I-V),亮度-电压(B-V)和亮度-电流(B-I)特性.提出了在不同激发条件下的I-V,B-V和B-I的经验公式.证明了DCEL器件在AC条件下按激发条件可分为三个负载区:容性负载区,电阻负载区和混合负载区.在不同的负载区DCEL器件呈现完全不同的光电特性.证明了在不同负载区工作时磷光粉层内电场分布和电子能量分布截然不同.分析了上述特性的原因.证明了老化和形成过程具有同样的物理机制,老化是形成过程的继续.     

有机薄膜电致发光器件载流子注入和传输性质的研究

制备了不同电极、不同厚度、以8-羟基喹啉铝螯合物(Alq3)为发光层的有机薄膜电致发光(TFEL)器件。分析了它们的电流密度-电压关系。不同阳极器件的电流变化很大,而改变阴极时电流密度的变化较小,说明电流以空穴为主。根据不同阴极器件的电致发光效率的比较,说明电子是决定器件电致发光效率的少数载流子。从不同厚度的器件的结果讨论了载流子的传输性质,认为在ITO/Alq3/Al器件中的电流符合陷阱限制的空间电荷电流.     

新型蓝光OLED材料和器件

基于有机材料的电致发光技术可以应用于超薄平面显示和有机固体激光器等方面,在近20年来取得了飞速的发展,基本实现了红、绿、蓝三基色发光.绿色材料发展最快,基本达到了商业化实用阶段,而红色和蓝色材料的问题较多,特别是稳定、高效率的蓝光更具有挑战性.综述了近期我们对蓝光材料的分子设计与合成,以及蓝光器件的一些研究.主要包括金属络合物2,3-二甲基-8-羟基喹啉锂和聚芴衍生物树枝状的聚芴化合物的蓝光材料,以及利用基激复合态实现蓝光的电致发光器件.通过光致发光、电致发光光谱以及电压-电流-发光亮度特征曲线等研究了这些发光材料和器件的性质.现在蓝光器件的色纯度和工作寿命还有待提高.     

在正向电压激发下ZnSe MIS二极管的自由激子发光

研究了最低温度为20~30K时,在正向电压激发下ZnSe MIS二极管的激子发光光谱,在这一温度下,二极管有可能通过足以产生发光的电流.对于利用通常气相技术生长的高纯晶体所制备的二极管,其电致发光几乎完全由Γ8→Γ6自由激子发光的1LO和2LO声子伴线所组成.根据Gross等人的半经典理论,讨论了两个谱带的形状.结果是谱带的宽度和不对称性归结为激子服从Maxwell-Boltzmann分布,其有效激子温度接近于晶格温度.     

Er离子注入的富硅SiO2MOS-LED的可见和红外电致发光特性

通过Er离子和Si离子注入并结合高温退火制备了Er掺杂的富硅SiO2薄膜以及ITO/SiON/富硅SiO2:Er/Si MOS结构电致发光器件.研究了富Si浓度的变化对Er3+离子掺杂的电致发光器件的发光性能和传导特性的影响.发现不同Si含量对Er3+离子的不同能级的电致发光会产生不同作用.在富Si量小于5％的条件下,...     

C-ZnSe:Ga的室温蓝色注入式发光

本文首次报导了C-ZnSe:Ga的室温蓝色注入式发光,测量了有关特性并讨论了发光机理.电致发光光谱具有强的4800A的蓝峰和弱的6300A的红峰.随着正向电压的增加,6300A的自激活发射相对减弱,而4800A的蓝色边缘发射逐渐增强.因此,当电压增加时,发光颜色由红色经黄色和绿色,逐渐变成纯蓝色.在明亮的房间里可以观察到鲜明的蓝色发射.文末提出了ZrSe多色显示的设想.     

蓝色有机发光材料LiBq4的合成及其发光特性

蓝色有机发光材料的开发对于实现有机发光二极管(OLED)的全彩色化具有十分重要的意义.报道了蓝色有机发光材料8-羟基喹啉硼化锂(LiBq₄)的合成及提纯,研究了LiBq₄的光致发光特性,并用LiBq₄作为发光材料制备了蓝色有机发光器件,研究了电子传输层Alq₃的厚度及空穴缓冲层CuPc对器件电流-电压和亮度-电压特性的影响.结果表明,LiBq₄的光致发光峰值波长为452nm,器件ITO/PVK:TPD/LiBq₄/Alq₃/Al的电致发光光谱峰值波长位于475nm处,在25V工作电压下其最高亮度约为430cd/m².但CuPc的加入加剧了器件中载流子的不平衡注入,导致器件性能恶化.通过调整Alq₃的厚度,同时在Alq₃和Al阴极之间加入LiF薄膜以提高电子注入效率,获得了较为理想的实验结果.     

Synthesis and Luminescent Properties of 1,4,5-Triphenylimidazole‒Phenothiazine Fluorophores

Two blue donor–acceptor fluorophores with 1,4,5-triphenylimidazole as the electron-transporting unit and phenothiazine as the hole-transporting unit were synthesized by grafting 1,4,5-triphenylimidazole moieties onto 3- and 3,7-position of the phenothiazine core and characterized by spectroscopic methods. Their thermal stability, photophysical, electrochemical and electroluminescence properties were systematically investigated. These compounds exhibit good thermal stability and show blue emission in dichloromethane solution and thin solid films. The solution-processed doped devices were fabricated by using these fluorophores as the emitting dopant in 1,3-bis(N-carbazolyl)benzene host, in which the device fabricated from the fluorophore containing two 1,4,5-triphenylimidazole moieties exhibited blue emission with a luminance of 648 cd/m² and external quantum efficiency of 1.48%.

     

一种特殊结构的金刚石薄膜电致发光器件

蓝色波段电致发光器件的研究是近年来光电子和材料科学研究领域最引入注目的研究课题之一。文章作者分别利用脉冲激光淀积设备和微波等离子体化学气相沉积设备制备了不同结构的高质量掺杂金刚石薄膜电致发光器件，并对其发光光谱特性，频率特性以及发光强度与杂质浓度及激发电压的依赖关系进行了研究，发现了金旬石薄膜紫外线的发光现象，取得了一系列有价值的结果。     

Optical Properties and Structure of Electroluminescent SiOx:Tb Films

Using nondestructive optical methods (measurement of transmission spectra in the visible and IR regions and multiangular ellipsometry), we have studied the structural changes in SiO _x :Tb films subjected to high–temperature annealing in air, which are responsible for the appearance of electroluminescence in light–emitting structures based on them. It has been established that the appearance of green electroluminescence in such a film (upon annealing of the film in air at temperatures of 600–800°C) is due to the structural changes in its matrix, leading to partial disproportionation of the thermally deposited SiO _x :Tb film (as a result, the film represents a mixture of several phases – Si, SiO_x, and SiO₂). Films showing blue electroluminescence (annealing temperature 1000°C) are characterized by a higher content of oxygen, a better compactness, and a better macroscopic homogeneity in comparison with films showing green electroluminescence. It is also shown that the thermal cycling accompanying the annealing leads to the appearance of birefringence and scattering in SiO _x O:Tb films. It is anticipated that the annealing–stimulated structural changes taking place at both the micro– and the macrolevel should cause changes in the local surroundings of the luminescence center and in the conditions for heating the charge carriers exciting the luminescence centers.     

Ag或Cu离子注入形成的ZnS MIS结及其蓝色电致发光

本文叙述了在室温下用能量为70~100keV,剂量为1~3×1015cm-2的Ag或Cu离子注入到低阻ZnS晶体中,经N2气流350℃下退火处理,并用扫描电镜观测晶片断面的反射电子像(REI),吸收电子像(AEI)和二次电子像(5EI),发现了经离子注入的ZnS晶片表面存在一个厚约1μ的绝缘层,还根据对MIS结C-V特性测量,计算了二极管Ⅰ层的厚度为1.1μ,它与用扫描电镜观测的结果一致.文中还测量了ZnS:Ag(或Cu)MIS二极管在正向电压下的发光光谱,根据谱峰位置表明发光分别起源于Ag(或Cu)发光中心.在室温下用肉眼观察二者皆为蓝色电致发光.     

金刚石薄膜电致发光现象的研究进展

阐明了金刚石薄膜电致发光研究的重要意义．综述了金刚石薄膜电致发光现象研究的进展情况，指出目前该方面研究中存在的问题，并提出了进一步提高金刚石薄膜蓝区电致发光强度的可能途径．     

Electroluminescence of double-doped diamond thin films

A new electroluminescence device is fabricated by microwave plasma chemical vapour deposition system and electron beam vapour deposition system. It is comprised of highly doped silicon/diamond/boron/nitrogen-doped diamond/indium tin oxide thin films. Effects of process parameters on morphologies and structures of the thin films are detected and analysed by scanning electron microscopy, Raman spectrometer and x-ray photoelectron spectrometer. A direct-current (DC) power supply is used to drive the electroluminescence device. The blue light emission with a luminance of 1.2 cd·m 2 is observed from this double-doped diamond thin film electroluminescence device at an applied voltage of 105 V.     

Emission tuning study of RGB blends. Interaction of two EL polymers and a red dye

A study of light emission in photo- and electroluminescence in blends composed of a blue and a green emitting polymers with a red dye was performed. To gain information about the tunability of the RGB mixture, the blends varied in composition. The polymers were poly(2,7-9,9′-dihexylfluorenediyl) (blue), poly(9,9-di-hexylfluorenediyl divinylene-alt-1,4-phenylenevinylene) (green) and the dye was 4-(dicyanomethylene)-2-methyl-6-(dimethylaminostyryl)-4H-pyrane (red).It was verified that in photoluminescence Forster type energy transfer plays the main role in the emission. In solution a large concentration of the acceptors is needed to attain the transfer radii, whereas in the solid state, the transfer is very sensitive to small variations in the acceptor content, with large changes in emission spectra. The band gaps of the components allowed a cascade energy transfer mechanism. In electroluminescence, apart from the energy transfer mechanism, an important role is played by the trapping of charge carriers, resulting in significant differences between the PL and EL spectra.     

Small-molecular white organic light-emitting devices employing 2, 5, 2′, 5′-tetra (<Emphasis Type="Italic">p</Emphasis>-trifluoromethylstyryl)-biphenyl as single-emitting component

We demonstrate a promising single layer white light-emitting device using a dimeric trimeric phenylenvinylene derivative as emitting layer. The broad electroluminescence emission band is composed of blue component from singlet excited state of individual 2, 5, 2′, 5′-tetra (p-trifluoromethylstyryl)-biphenyl molecule and long-wavelength electromer emission in electroluminescence. Therefore, white-light emission can also be obtained with a typical three-layer structure of ITO/NPB (50 nm)/TFM-TSB (50 nm)/Alq₃ (30 nm)/LiF/Al device. The maximum brightness of this device is 809 cd/m² at 217 mA/cm² and 13 V, and the maximum luminous efficiency is 1.49 cd/A at 11 mA/cm² and 8 V.      

金刚石薄膜电致发光研究

报道了金刚石薄膜电致发光现象.为进一步提高金刚石薄膜蓝区电致发光强度,分别采用了硼氮双掺杂法和稀土掺杂法制备出了金刚石薄膜电致发光器件,并采用低电容率的本征金刚石薄膜和氧化硅薄膜为绝缘层的夹层式器件结构.研究结果显示:采用稀土铈掺杂可以有效地提高金刚石薄膜蓝区电致发光强度,其蓝区最大电致发光强度可达3.5 cd/m2;采用低电容率绝缘膜的夹层式结构,能有效地提高电子进入发光层时的能量,并有助于提高器件发光的稳定性和发光寿命.     

Temperature‐dependent electroluminescence intensity in green and blue (In,Ga)N multiple‐quantum‐well diodes

The electroluminescence (EL) intensity has been investigated of green and blue (In,Ga)N multiple‐quantum‐well diodes grown on c ‐plane sapphire over a wide temperature range and as a function of current between 0.01 mA and 10 mA. The EL intensity of the green diode with p‐(Al,Ga)N electron blocking layer does not show low‐temperature quenching, especially at low injection levels, previously observed for the blue (In,Ga)N quantum‐well diodes. This finding rules out possi‐ bilities that the freeze‐out of holes at deep Mg acceptor levels and the failure of hole injections through the p‐(Al,Ga)N layer are directly responsible for the EL quenching at temperatures below 100 K. Variations of the EL efficiency with current level suggest that capture/escape efficiencies of injected carriers by the wells play an important role for the determination of EL external quantum efficiency. (© 2008 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)