共查询到20条相似文献,搜索用时 46 毫秒
1.
采用水热法在碳布基底上沉积了前驱体,然后在Ar气气氛中加热并用次磷酸钠在300~350℃磷化得到了纳米针阵列多孔材料3D CoP@CC,并分析了所得样品的物相、微观结构和电催化性能.XRD分析结果表明所得材料本体为正交结构的CoP,SEM分析结果表明所得阵列结构纳米针的直径在100 nm以下,长度约为10μm.电催化性能分析结果表明,制备所得该3D CoP@CC作为催化材料在0.5 mol/L硫酸溶液中表现出优异的电催化析氢性能,当电流密度为10 mA·cm-2时,过电位为124 mV.Tafel斜率为84.9 mV/dec,说明该3D CoP-CC电催化析氢的控速步为Volmer反应.从阻抗图谱可以看出有两个不完整的半圆弧,表明其具有两个时间常数,CPE2-P=0.5019意味着粗糙和多孔的电极表面产生了双层电容,电荷较难穿透,表明了阻抗的来源主要是传质与传荷. 相似文献
2.
面对化石能源危机问题,清洁高效的氢能源受到人们的广泛关注,电解水制氢成为新的研究热点。本文主要围绕铂/铜合金催化剂的合成、表征及其电解水析氢催化应用展开研究。采用溶剂热法合成铂/铜合金,通过XRD、SEM、TEM、EDS、XPS等表征铂/铜合金的组成结构和微观形貌,对铂/铜合金的构效关系进行探索。利用电化学测试系统测得铂/铜合金不同条件下的析氢催化性能。在0.5 mol/L H2SO4中,铂/铜合金的起始过电位为20.3 mV(10 mA·cm-2时),塔菲尔斜率为37.56 mV·dec-1;在1 mol/L磷酸缓冲盐溶液(PBS)中,铂/铜合金的起始过电位为35.0 mV(10 mA·cm-2时),塔菲尔斜率为52.12 mV·dec-1;在1 mol/L KOH中,铂/铜合金的起始过电位为25.3 mV(10 mA·cm-2时),塔菲尔斜率为36.82 mV·dec-1。对比发现,铂/铜合金在酸性电解质中展... 相似文献
3.
4.
利用电化学沉积法在碳纳米管纤维(CNTFs)上沉积了镍磷合金,对比了不同循环圈数、不同镍磷比例下制备的碳纳米管纤维负载镍磷合金(Ni-P/CNTFs)电极在中性电解质溶液中的电催化析氢性能,发现当电沉积液中镍磷比为2:1时,沉积50圈时制备出的样品具有最佳的电催化析氢性能,产生10 mA·cm-2电流密度仅需138 mV过电势,塔菲尔(Tafel)斜率为83 mV·dec-1,同时具有良好的稳定性.并且在保持催化性能不变的前提下,样品可以进行弯曲,扩展了应用领域. 相似文献
5.
6.
7.
氢能的引入能有效提升配电网的供电可靠性,而电解水制氢是实现低碳转型的关键技术,开发高效的电解水催化剂势在必行。过渡金属氧化物储量大、催化活性高,是具有广阔应用前景的析氧反应催化剂。本文通过射频等离子体处理制备石墨烯上负载Co3O4析氧催化剂,XRD、Raman和XPS测试结果显示,二维结构石墨烯的引入加速表面电子迁移,增大了反应面积。等离子体处理促进了纳米粒子在石墨烯上的负载,利用等离子体刻蚀作用在催化剂表面制造出大量碳结构缺陷和氧空位结构,改善了活性位点分布,有效调控Co3O4电子结构,提高析氧催化活性。电化学测试表明,本文中合成的Co3O4@rGO在电流密度为50 mA·cm-2时的过电位为410 mV,动力学反应速率较快,表现出优于商业IrO2的析氧催化活性。 相似文献
8.
氧析出反应(OER)涉及多个电子的转移,动力学较为缓慢,被认为是电解水过程的瓶颈半反应.因此开发高效、稳定的氧析出反应电催化剂,降低该反应的外加过电位是电解水技术发展的关键.本文采用简单的化学浴沉积方法,经低温焙烧成功制备出多孔的无定型NiCo氧化物催化剂,并且该方法一次制备量可达克级.无定型NiCo氧化物因富含氧空位相对于其晶态的NiCo2O4尖晶石复合氧化物具有更优的OER性能,在碱性介质(0.1 mol/L KOH)中当电流密度为10 mA/cm2时的过电位为370 mV,并且表现出优异的催化稳定性. 相似文献
9.
利用化学气相沉积法在Si/SiO2衬底上生长出了InP纳米线,制备了基于InP纳米线的底栅场效应晶体管并研究了其电输运特性.对不同生长温度器件的阈值电压、亚阈值斜率、场效应迁移率以及载流子浓度等参数进行了计算和比较.结果表明,生长温度对InP纳米线的形貌影响较大.800℃生长温度的InP纳米线性能较好,该器件阈值电压约为-8.5V,亚阈值斜率为142.4 mV/decade,跨导为258.6 nS,开关比>106,场效应迁移率高达177.8cm2/(V·s),载流子浓度达2.1×101s cm-3. 相似文献
10.
11.
12.
A. L. Bingham J. E. Drake C. Gurnani M. B. Hursthouse M. E. Light M. Nirwan R. Ratnani 《Journal of chemical crystallography》2006,36(10):627-630
Triethyl ammonium Salt of O,O′-bis(p-tolyl)dithiophosphate and O,O′-bis(m-tolyl)dithiophosphate have been obtained by reaction of p- and m-cresol, respectively with P2S5 in toluene and have been characterized by elemental analysis, IR, 1H and 31P NMR spectroscopy. The molecular structure of O,O′-bis(p-tolyl)dithiophosphate has been determined. Crystal data: [Et3NH]+[(4-MeC6H4O)2PS2]−: Monoclinic, P21/c, a=15.2441(9) ?, b=10.415(2) ?, c=3.9726(9) ?, β=91.709(7)°, V=2217.5(1) ?−3, Z=4.Supplementary materials Additional material available from the Cambridge Crystallographic Data Centre (CCDC no. 600927 for [Et3NH]+[(4-MeC6H4O)2PS2]− comprises the final atomic coordinates for all atoms, thermal parameters, and a complete listing of bond distances and angles. Copies of this information may be obtained free of charge on application to The Director, 12 Union Road, Cambridge CB2 2EZ, UK (fax: +44-1223-336033; email: deposit@ccdc.cam.ac.uk or www:http://www.ccdc.cam.ac.uk). 相似文献
13.
We perform first-principles coexistence simulations of the low-density and the high-density phases of supercooled liquid silicon and find a negative slope for the coexisting line in the temperature-pressure plane. Electron density maps and electron-localization function plots of the two phases of silicon show marked differences. The calculated differences suggest more localized electrons in the low-density liquid compared to the high-density liquid, coming from an increased population of covalent bonds, which further explain the calculated negative slope in the two phase coexistence regime. This is consistent with the presence of a pseudo-gap in low-density liquid silicon, absent in the high-density liquid which shows a metallic behavior. 相似文献
14.
Tosha Barclay Wallace Cordes Fu-May Yang Shaw-Tao Lin 《Journal of chemical crystallography》1997,27(6):359-362
Structures of both thecis andtrans isomers of dithiahexahydro[3.3]metacyclophane, ?C6H4?CH2SCH2?C6H10?CH2SCH2?, have been determined, wherecis andtrans refer to the attachments to the cyclohexane ring. Thecis form crystallizes in the monoclinic space groupP21/c witha=8.4299(11)Å,b=21.772(2)Å,c=8.9724(13)Å, β=116.574(11)o, andZ=4. Thetrans isomer packs into the monoclinic space groupP21 witha=8.159(16)Å,b=10.185(5)Å,c=9.558(2)Å, β=112.435(18)o, andZ=2. The cyclohexane ring of thecis isomer is in the chair conformation, while the cyclohexane of thetrans isomer is found in a twisted boat conformation. 相似文献
15.
以表面活性剂CTAB和SDBS为化学添加剂,采用化学共沉淀法对碳酸锶晶体的生长形态进行调控,成功地制备出了实心的树枝状和花瓣为空心的花状碳酸锶粉体,并用X射线衍射(XRD)、扫描电子显微镜(SEM)和傅里叶变换红外光谱(FT-IR)等分析手段对样品进行了表征;最后重点对化学添加剂可能产生的影响机理进行了初步的探讨.结果表明,CTAB和SDBS在晶体生长的过程中能起到显著的影响作用,两者对粒子分散性能的作用效果相反,而且后者对晶体(013)和(213)晶面表面能降低的贡献明显大于前者. 相似文献
16.
Tosha Barclay Wallace Cordes Fu-May Yang Shaw-Tao Lin 《Journal of chemical crystallography》1998,28(3):171-175
Both the cis and trans isomers of 3,11,18,26-tetrathiatricyclo[26.2.2.15,9.213,16.120,24] hexatriaconta-5,7,9,20,22,24-hexene have been prepared and structurally characterized. Each of these centrosymmetric tetrathia dimers includes two cyclohexane rings in chair conformations with either 1,4-cis or 1,4-trans bonding and two meta-substituted benzene rings. The cis isomer packs into the monoclinic space group P21/a with a = 10.485(3)Å, b = 10.3956(18)Å, c = 14.1343(10)Å, = 105.200(13)°, Z = 2 and refined to an R factor of 0.046. The trans isomer crystallizes in the monoclinic space group P21/c with a = 10.7217(12)Å, b = 5.6797(7)Å, c = 25.415(5)Å, = 96.001(12)°, Z = 2 and refined to an R factor of 0.043. In the cis structure each benzene ring faces a cyclohexane ring while in the trans structure the cyclohexane rings face one another. 相似文献
17.
Lin Zhu Karl Seff Thomas Witzke Lutz Nasdala 《Journal of chemical crystallography》1997,27(5):325-329
The structure of Zn4Na(OH)6SO4Cl·6H2O, a secondary mineral from Hettstedt, Germany, was determined by single-crystal X-ray diffraction. The crystals are hexagonal,a=8.413(8),c=13.095(24) Å, space group $P\bar 3$ , Z=2. The structure was refined to R=0.0554 and Rw=0.0903 for 970 reflections with I≥3σ(I). The structure can be described as zinc hydroxide layers perpendicular toc, from which sulfates and chlorides extend. The layers are held together by a system of hydrogen bonds involving hexaaquo Na+ ions which occupy the interlayer space. 相似文献
18.
Jerry P. Jasinski Ray J. Butcher Anil N. Mayekar H. S. Yathirajan B. Narayana B. K. Sarojini 《Journal of chemical crystallography》2009,39(10):761-765
Abstract The title compound, C18H18BrN3O3S, a derivative of 1,3,4-oxadiazole, crystallizes in the triclinic space group P-1 with unit cell parameters a = 6.8731(3), b = 8.9994(4), c = 15.7099(6) ?, α = 92.779(3)°, β = 130.575(3)°, γ = 107.868(4)°, Z = 2. The dihedral angle between the mean planes of the planar naphthyl and morpholine (chair) rings with the planar oxadiazol
ring is 50.1(8) and 76.8(6)°, respectively. The planar naphthyl ring is twisted 52.2(5)° with the mean plane of the morpholine
ring. A group of four intermolecular close contacts are observed between a bromine atom and hydrogen atoms from the closely
packed naphthyl, morpholine and oxy–methyl groups in the unit cell. These molecular interactions in concert with an additional
series of π–π stacking interactions that occur between the center of gravity of the two 6-membered rings of the naphthalene
group influence the twist angles of each of these three groups. A MOPAC AM1 calculation of the conformation energy of the
crystal structure [226.0128(9) kcal] compared to that of the minimum energy structure after geometry optimization [29.9744(1) kcal]
reveals a significantly reduced value. The twist angles of the three groups above also change after the AM1 calculation giving
support to the influence of both intermolecular C–H···Br short-range interactions and Cg π–π stacking interactions on these
angles which therefore play a role in stabilizing crystal packing.
Graphical Abstract Crystal structure of 5-{[(6-bromonaphthalen-2-yl)oxy]methyl}-3-(morpholin-4-ylmethyl)-1,3,4-oxadiazole-2(3H)-thione, C18H18BrN3O3S, is reported and its geometric and packing parameters described and compared to a MOPAC computational calculation.
Electronic supplementary material The online version of this article (doi:) contains supplementary material, which is available to authorized users. 相似文献
19.
本文以掺F的SnO2导电玻璃为基板,以硝酸锌水溶液为电解液,采用三电极恒电位体系电沉积制备ZnO纳米棒阵列,系统考察了硝酸锌浓度和沉积电位等工艺参数对ZnO纳米棒阵列的微观形貌及其发光性能的影响规律.结果表明,硝酸锌浓度和沉积电位对纳米棒阵列的形貌有显著影响,控制适宜的工艺条件可以制备出直径分布均匀、结晶性好且纯度高的六方纤锌矿ZnO纳米棒阵列.荧光光谱分析表明,电沉积制备出的ZnO纳米棒阵列在385 nm附近有一个强荧光发射峰,且发光性能稳定、对纳米棒阵列微观形貌的细微变化不敏感,使其在发光二极管和激光器等领域具有广阔的应用前景. 相似文献
20.
Zun-Ting Zhang Xue-Ling Zhang Bo-Lun Yang Yao-Dong Zhang 《Journal of chemical crystallography》2006,36(7):407-411
Irisolidone (5,7-dihydroxy-6,4′-dimethoxyisoflavone) was isolated from the flowers of Pueraia lobata and its crystal structure was examined by X-ray single crystal diffraction. The crystal structure of irisolidone is monoclinic, space group P21/c with a = 15.491(9) ?, b = 7.895(4) ?, c = 13.321(7) ?, β = 110.546(9)° and Z = 4. Hydrogen bonding and aromatic π–π stacking assemble the title compound into a three-dimensional networking structure. 相似文献