表面引发接枝聚合法制备高接枝度的接枝微粒SiO2-g-PMAA

将偶联剂γ-氨丙基三甲氧基硅烷(AMPS)键合在硅胶微粒表面,得到改性微粒AMPS-SiO2;使改性微粒表面的氨基与溶液中的过硫酸铵构成氧化-还原引发体系,实现了甲基丙烯酸(MAA)在硅胶微粒的表面引发接枝聚合,制得了高接枝度(0.30 g/g)的接枝微粒SiO2-g-PMAA;研究了影响表面引发接枝聚合的主要因素。 结果表明,适宜的温度为40 ℃。 已接枝到硅胶表面的聚合物层对后续的接枝聚合产生阻隔作用。 适宜的引发剂用量为单体质量的1.1%,适宜的单体质量分数为5%左右。     

采用巯基-BPO氧化还原引发体系实现GMA在硅胶微粒表面的高效接枝聚合

使用偶联剂γ-巯丙基三甲氧基硅烷(MPMS,KH-590),对微米级硅胶微粒进行了表面化学改性,制得了表面带有巯基的改性微粒MPMS-SiO2.使改性微粒MPMS-SiO2表面的巯基与溶液中的BPO构成氧化-还原引发体系,实现了油溶性单体甲基丙烯酸缩水甘油酯(GMA)在硅胶微粒表面的引发接枝聚合,制得了接枝度为26g/100g的接枝微粒PGMA/SiO2.采用红外光谱(FTIR)、扫描电镜(SEM)及热重分析(TGA)等方法对接枝微粒PGMA/SiO2进行了表征。在此基础上,重点研究了主要因素对巯基-BPO体系引发GMA接枝聚合的影响.研究结果表明,巯基-BPO体系引发的接枝聚合,由于活性位点位于固体表面,因此也是一种表面引发接枝法。与在固体微粒表面引入可聚合双键的"穿过接枝"("grafting through")法相比,巯基-BPO引发体系可更有效地实现油溶性单体的接枝聚合.为制得高接枝度的接枝微粒PGMA/SiO2,适宜的温度为55℃,适宜的BPO用量为单体的1wt%左右,适宜的单体浓度为10 wt%。     

MMA接枝改性PVC/CaCO3纳米复合材料的力学性能

采用熔融共混法制备PMMA接枝改性纳米CaCO3增韧PVC（PVC/CaCO3）复合材料,并研究了复合材料的力学性能.结果表明,通过表面PMMA的接枝改性,可以显著提高纳米CaCO3增韧聚氯乙烯复合材料的拉伸强度和拉伸模量,在纳米CaCO3颗粒表面PMMA包覆层厚度为2nm时,复合材料的拉伸强度和拉伸模量达到极大值.对比于未处理纳米CaCO3和钛酸酯偶联剂处理纳米CaCO3,PMMA接枝改性纳米CaCO3增韧PVC复合材料的拉伸强度得到较大幅度提高.SEM显示,经过PMMA接枝改性后的碳酸钙在PVC基体中分散均匀,与基体界面结合良好.     

甲基丙烯酸丁酯在纳米TiO2表面的原位接枝

利用分子自组装技术,对纳米TiO2粒子表面组装上有机单分子层,使其带上不饱和基团C=C,在自组装单分子层表面原位引发甲基丙烯酸丁酯（BMA）单体聚合反应,使纳米TiO2表面形成化学键合的聚合物层,达到对纳米TiO2粒子改性的目的。讨论了不同反应条件对接枝聚合率的影响,通过FTIR、TG-DTA等分析手段,研究聚合改性物质的结构和改性后纳米TiO2粒子的分散稳定性。实验发现聚合改性后的纳米TiO2在有机相中有良好的分散性。     

聚四氟乙烯微粉辐照接枝苯乙烯的XPS研究

聚四氟乙烯微粉辐照接枝苯乙烯的ＸＰＳ研究许观藩，罗云霞，杨弘（中国科学院长春应用化学研究所，长春，１３００２２）关键词聚四氟乙烯，苯乙烯，表面接枝，ＸＰＳ用辐照方法在疏水性高聚物材料表面接枝聚合亲水性单体，可以达到改性的目的．文献中所用的高聚物材料包...     

构建芳叔胺-BPO氧化还原引发体系实现苯乙烯在硅胶微粒表面的高效接枝聚合

首先使用偶联剂γ-氨丙基三甲氧基硅烷(AMPS)对微米级硅胶微粒进行了表面改性,制得表面带有伯胺基的改性微粒SiO2-AMPS,接着使4-(二乙氨基)水杨醛(DEAS)与微球SiO2-AMPS发生席夫碱反应,制得表面含有芳叔胺基的改性微粒SiO2-DEAS.使改性微粒SiO2-DEAS表面的芳叔胺基团与溶液中的BPO构成氧化-还原引发体系,实现了油溶性单体苯乙烯(St)在硅胶微粒表面的引发接枝聚合,制得了高接枝度(27 g/100g)的接枝微粒SiO2-DEAS-g-PSt.采用红外光谱(FTIR)、扫描电镜(SEM)及热重分析(TGA)等方法对接枝微粒SiO2-DEAS-g-PSt进行了表征.在此基础上,重点研究了主要因素对芳叔胺-BPO体系引发St接枝聚合的影响.研究结果表明,与在固体微粒表面引入可聚合双键的"穿过接枝"(grafting through)法相比,芳叔胺-BPO体系引发的接枝聚合,由于活性位点位于载体表面,故具有高的接枝度,是油溶性单体的一种高效率的表面引发接枝法.为制得高接枝度的接枝微粒SiO2-DEAS-g-PSt,适宜的温度为50℃,适宜的BPO用量为单体的3 wt%左右,适宜的单体浓度为10 wt%.     

炭黑接枝方法与接枝炭黑应用的研究进展

炭黑接枝是常用的炭黑表面改性方法。讨论了最新的炭黑接枝方法,主要包括二次接枝法、γ-射线辐射接枝、三氯乙酰基团与六羰基钼引发乙烯基单体聚合接枝,偶联接枝与聚合物交联及其它方法;并对接枝炭黑在新材料领域的臆用作了介绍。     

二氧化硅粒子的表面化学修饰——方法、原理及应用

本文综述了近年来国内外对二氧化硅粒子表面化学修饰的研究成果,主要介绍了偶联剂法、表面接枝法和一步法的反应原理,探讨了各种改性方法的关键问题和优势,重点介绍了表面接枝法,包括以普通自由基聚合、原子转移自由基聚合和可逆加成-断裂链转移自由基聚合为原理的表面聚合生长接枝法和以开环加成、点击化学和酯化反应为原理的偶联接枝法。由于表面接枝法一般需要偶联剂在二氧化硅表面引入官能团,本文亦简要介绍了硅烷偶联剂及其修饰机理和一步法的反应原理。表面修饰的基团或接枝的聚合物赋予二氧化硅粒子新的性能;经表面修饰的二氧化硅粒子,提高了在有机溶剂或有机基体中的分散性,增加了与有机基体的界面相容性,并已广泛应用于新材料的合成。     

芴酮引发光接枝改性LDPE膜的研究

采用紫外光引发接枝表面改性的方法,以芴酮(FL)为引发剂,在低密度聚乙烯(LDPE)薄膜表面上接枝丙烯酸(AA)、甲基丙烯酸(MAA)、丙烯酸甲酯(MA)、甲基丙烯酸甲酯(MMA)、丙烯酰胺(AM)等单体,以赋予薄膜表面新的化学性质.考察了引发剂浓度、紫外光的辐照时间、辐照强度、单体种类对LDPE薄膜接枝程度的影响.结果表明,在一定范围内,增加芴酮浓度,可以提高单体的接枝率,但当芴酮浓度达到5%时,接枝率反而下降.延长辐照时间至4 min和提高紫外光的辐照强度达100 W/m2,均有利于接枝反应的进行.不同单体在LDPE膜上的接枝能力与单体的活性、单体与基材的相容性等因素有关.接枝后,LDPE与水的接触角下降程度不仅与单体在膜上的接枝量有关,还与接枝单体的亲水性能密切相关.     

表面光接枝原理,方法及应用前景

介绍了表面光接枝的原理,方法和应用前景,表面光接枝主要是用芳酮引发有机材料产生表面自由基,从而引发单体聚合生成表面接枝链。实施方法有气相法,液相法和连续液相法。表面光接枝应用领域广泛,可用于聚合材料的表面改性以及表面功能化。     

Preparation of hemispherical hollow silica microcapsules with different affinity surface by using spherical vaterite calcium carbonate as template

We developed a method to prepare hemispherical hollow silica microcapsules (HHSM) with different affinity surfaces using spherical vaterite calcium carbonate (SVCC) as a template. The preparation process composed of the adhesion of calcium carbonate onto the surface of methyl methacrylate (MMA) droplets followed by suspension polymerization, the partial etching of calcium carbonate on the polymethyl methacrylate (PMMA) mother particle, the formation of silicon dioxide powder by sol–gel reaction and their deposition onto the etched flat surface of calcium carbonate, the surface modification of deposited silicon dioxide with silane coupling agent, the removal of the mother particle with acetone, the formation of silicon dioxide powder by sol–gel reaction and deposition onto the exposed hemispherical surface of calcium carbonate, and the surface modification of deposited silicon dioxide with silane coupling agent. The synthesized microcapsules had a complete hemispherical structure and both hydrophilic and hydrophobic surfaces. Copyright © 2007 John Wiley & Sons, Ltd.     

GRAFTING OF POLYSTYRENE ONTO A NANOMETER SILICA SURFACE BY MICROEMULSION POLYMERIZATION

The grafting of polystyrene onto a nanometer silica surface by microemulsion polymerization is described. Silicawas functionalized with 3-methacryloxypropyltrimethoxysilane coupling agent before polymerization. A mixture of ionic andnon-ionic surfactants as well as water-soluble and oil-soluble initiators were used. The effect of the amount of silica and ionicsurfactant on the graft polymerization was studied. The graft polymerization procedure for styrene was also applied to methylmethacrylate. Composite particles with a core-shell structure were obtained and the yield and grafting efficiency of monomerwere high.     

构建巯基-Ce(Ⅳ)盐氧化还原引发体系实现丙烯腈在硅胶微粒表面的高效接枝聚合

使用偶联剂γ-巯丙基三甲氧基硅烷(MPMS,KH-590),对微米级硅胶微粒进行了表面化学改性,将巯基引入硅胶微粒表面(SiO2-MPMS),构成巯基-Ce(Ⅳ)盐氧化-还原引发体系,探索研究了丙烯腈在硅胶微粒表面的引发接枝聚合,制得了高接枝度(30 g/100g)的接枝微粒SiO2-MPMS-g-PAN.采用红外光谱(FTIR)、扫描电镜(SEM)及热重分析(TGA)等方法对接枝微粒SiO2-MPMS-g-PAN进行了表征.在此基础上,重点研究了主要因素对巯基-Ce(Ⅳ)盐体系引发AN接枝聚合的影响.研究结果表明,类似于羟基-Ce(Ⅳ)盐体系,巯基-Ce(Ⅳ)盐体系也可以有效地引发乙烯基单体在固体微粒表面接枝聚合.与在固体微粒表面引入可聚合双键的"grafting through"接枝聚合法相比,铈盐引发的接枝聚合,由于活性位点居于载体表面,故具有高的接枝度,是一种高效率的表面引发接枝法.为制得高接枝度的接枝微粒SiO2-MPMS-g-PAN,本研究体系适宜的酸浓度为0.25 mol/L;Ce(Ⅳ)盐浓度为5.0×10-3 mol/L;接枝聚合宜在50℃下进行.     

二步法聚丙烯/丙烯酸表面接枝聚合研究

研究了二步法聚丙烯膜表面的丙烯酸接枝反应 .实验发现 ,以醋酐为溶剂的反应体系所得接枝率明显好于以水为溶剂的体系 ;接枝率随光敏剂浓度、单体浓度增大而增加 ;提高反应温度 ,可使接枝率明显增大 ;接枝后的聚丙烯膜表面亲水性可明显改善 .并用红外光谱证实了丙烯酸在聚丙烯膜表面的接枝 .     

Vapor-phase graft copolymerization of binary solid monomers onto poly(ethylene-co-vinyl acetate) film by ultraviolet irradiation

Vapor-phase graft copolymerizations of acenaphthylene–maleimide or acenaphthylene–maleic anhydride binary solid monomers onto poly(ethylene-co-vinyl acetate) films were carried out under ultraviolet irradiation. The extent of sorption of single or binary monomers increased with the increasing vinyl acetate content in the backbone polymers. The sorbed binary monomers were mainly composed of acenaphthylene, but the maleimide or maleic anhydride fraction increased with the increasing vinyl acetate content of the films and the composition was little affected by surface hydrolysis. In all series of graft polymerization of single or binary monomers the overall extent of grafting increased with the vinyl acetate content and was suppressed by the surface hydrolysis of the backbone film. The composition of the grafted copolymer, however, differed markedly, depending on the combination of binary monomers. The grafted copolymer in the acenaphthylene–maleimide system was composed mainly of acenaphthylene units, whereas that in the acenaphthylene–maleic anhydride system was composed mainly of maleic anhydride units. The results were compared with those of γ-ray grafting, and it was suggested that the contribution of a direct supply of monomers from vapor phase and the existence of an acetoxy group on the surface of the film should play an important role in the grafting reaction.     

Ultrahigh‐molecular‐weight‐polyethylene‐fiber surface treatment by electron‐beam‐irradiation‐induced graft polymerization and its effect on adhesion in a styrene–butadiene rubber matrix

Aiming to develop a high‐performance fiber‐reinforced rubber from styrene–butadiene rubber (SBR), we applied a special technique using electron‐beam (EB)‐irradiation‐induced graft polymerization to ultrahigh‐molecular‐weight‐polyethylene (UHMWPE) fibers. The molecular interaction between the grafted UHMWPE fibers and an SBR matrix was studied through the evaluation of the adhesive behavior of the fibers in the SBR matrix. Although UHMWPE was chemically inert, two monomers, styrene and N‐vinyl formamide (NVF), were examined for graft polymerization onto the UHMWPE fiber surface. Styrene was not effective, but NVF was graft‐polymerized onto the UHMWPE fibers with this special method. A methanol/water mixture and dioxane were used as solvents for NVF, and the effects of the solvents on the grafting percentage of NVF were also examined. The methanol/water mixture was more effective. A grafting percentage of 16.4% was the highest obtained. This improved the adhesive force threefold with respect to that of untreated UHMWPE fibers. These results demonstrated that EB irradiation enabled graft polymerization to occur even on the inert surface of UHMWPE fibers. However, the mechanical properties of the fibers could be compromised according to the dose of EB irradiation. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2595–2603, 2004     

Vapor-phase graft copolymerization of vinyl chloride and vinylidene chloride onto polypropylene fibers by simultaneous irradiation technique

The vapor-phase graft copolymerization of vinyl chloride and vinylidene chloride onto polypropylene fibers was studied by a simultaneous γ-irradiation technique. The weight increase during irradiation due to the grafting in monomers at constant vapor pressure was measured by a sensitive spring balance. The sorption of both monomers onto unirradiated polypropylene fibers was also measured. The graft copolymerization reaction was suppressed with increasing irradiation temperature, and the overall activation energies of grafting were negative in both monomers, ?2.4 kcal/mole for vinyl chloride and ?6.3 kcal/mole for vinylidene chloride. The initial rate of grafting increased linearly with the vapor pressure of monomers. The above dependence was found to parallel the sorption of monomers on polypropylene fibers. The reaction rates were proportional to the 0.9 power of the dose rate in both monomers. The relationship between the grafting and the sorption of monomers was discussed on the basis of kinetics.     

Graft polymerization of vinyl monomers inside macroporous polyacrylamide gel,cryogel, in aqueous and aqueous‐organic media initiated by diperiodatocuprate(III) complexes

Graft polymerization initiated by diperiodatocuprate(III) complex (Cu(III)) initiator was found to be an effective and convenient method for graft polymerization of vinyl monomers onto macroporous polyacrylamide gels, the so‐called cryogels (pAAm‐cryogels). The effect of time, temperature, monomer and initiator concentration during the graft polymerization in aqueous and aqueous‐organic media was studied. The graft polymerization of water‐soluble monomers as [2‐(methacryloyloxy)ethyl]‐trimethylammonium chloride, 2‐hydroxyethyl methacrylate, N‐isopropylacrylamide, and N,N‐dimethylacrylamide proceeds with higher grafting yield in aqueous medium, as compared with that in aqueous‐organic media. Graft polymerization in aqueous‐organic media such as water–DMSO solutions allows grafting of water‐insoluble monomers such as glycidyl methacrylate and N‐tert‐butylacrylamide with high grafting degrees of 100 and 410%, respectively. It was found that the deposition of initiator on the pore surface of cryogels promoted graft polymerization by facilitating the formation of the redox couple Cu(III)‐acrylamide group. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1952–1963, 2006     

Electrochromatography in poly(dimethyl)siloxane microchips using organic monolithic stationary phases

This paper shows the in situ synthesis of an hexyl acrylate monolith in PDMS microfluidic devices and its subsequent use as stationary phase for electrochromatography on chip. To overcome the ability of PDMS material to absorb organic monomers, surface modification of the enclosed channels was realized by UV-mediated graft polymerization. This grafting procedure is based on the preliminary adsorption of a photoinitiator onto the PDMS surface and polymerization of charged monomers. Next, hexyl acrylate monoliths were cast in situ using photopolymerization process. The chromatographic behavior of the monolithic column was confirmed by the successful separation of derivatized catecholamines in the PDMS device using a 30 mm effective separation length (100 microm x 100 microm section). Efficiencies reached up to 200,000 plates per meter.