Adsorption of Acid Blue 193 from aqueous solutions onto Na-bentonite and DTMA-bentonite

Dodecyltrimethylammonium bromide-modified bentonite (DTMA-bentonite) was prepared and tested as an adsorbent for an acid dye (Acid Blue 193, AB193) removal from aqueous solution in comparison with Na-bentonite. The effect of various experimental parameters was investigated using a batch adsorption technique. In this manner, the adsorption isotherms, adsorption kinetics, and temperature and pH effects upon Acid Blue 193 adsorption on Na-bentonite and DTMA-bentonite were thoroughly examined. Results show that a pH value of 1.5 is favorable for the adsorption of Acid Blue 193. The isothermal data could be well described by the Freundlich equation. The dynamical data fit well with the pseudo-second-order kinetic model. The adsorption capacity of DTMA-bentonite (740.5 mg g(-1)) was found to be around 11 times higher than that of Na-bentonite (67.1 mg g(-1)) at 20 degrees C. Thermodynamic parameters such as activation energy (E(a)) and change in the free energy (DeltaG(0)), the enthalpy (DeltaH(0)), and the entropy (DeltaS(0)) were also evaluated. The overall adsorption process was exothermic but it is only spontaneous at 20 degrees C. The results indicate that Na-bentonite and DTMA-bentonite could be employed as low-cost alternatives to activated carbon in wastewater treatment for the removal of color which comes from textile dyes.     

Removal of dyes from colored textile wastewater by orange peel adsorbent: equilibrium and kinetic studies

The use of low-cost and ecofriendly adsorbents has been investigated as an ideal alternative to the current expensive methods of removing dyes from wastewater. Orange peel was collected from the fields of orange trees in the north of Iran and converted into a low-cost adsorbent. This paper deals with the removal of textile dyes from aqueous solutions by orange peel. Direct Red 23 (DR23) and Direct Red 80 (DR80) were used as model compounds. The adsorption capacity Q0 was 10.72 and 21.05 mg/g at initial pH 2. The effects of initial dye concentration (50, 75, 100, 125 mg/l), pH, mixing rate, contact time, and quantity of orange peel have been studied at 25 degrees C. The Langmuir and Freundlich models were used for this study. It was found that the experimental results show that the Langmuir equation fit better than the Freundlich equation. The results indicate that acidic pH supported the adsorption of both dyes on the adsorbent. Orange peel with concentrations of 8 and 4 g/l has shown adsorption efficiencies of about 92 and 91% for DR23 and DR80, respectively. Furthermore, adsorption kinetics of both dyes was studied and the rates of sorption were found to conform to pseudo-second-order kinetics with a good correlation (R > or = 0.998). Maximum desorption of 97.7% for DR23 and 93% for DR80 were achieved in aqueous solution at pH 2. Finally, the effect of adsorbent surface was analyzed by scanning electron microscope (SEM). SEM images showed reasonable agreement with adsorption measurements.     

Water treatment to remove acid and basic dyes by biosorption on polysaccharide composites

A composite material based on cross-linked cationic starch and sodium alginate was synthesized and studied. The composite is an effective biosorbent for removing various types of synthetic dyes from water. The influence exerted on adsorption of a basic dye (Methylene Blue) and an acid dye (Methyl Orange) by temperature, pH, solution ionic strength, and biosorbent amount was examined, and the dye adsorption kinetics was studied. The adsorption isotherms were analyzed using various models of sorption equilibrium.     

Adsorption of dyes on carbon xerogels and templated carbons: influence of surface chemistry

The removal of textile dyes by adsorption onto carbon materials with extended mesoporosity is addressed in the present work. Two types of high surface area carbon adsorbents were prepared, namely a carbon xerogel and a templated carbon. Both materials were subsequently subjected to appropriate treatments in order to modify their surface chemistries, while keeping their textural properties relatively unchanged. The carbon adsorbents were extensively characterized by different techniques in order to correlate their adsorption performances with the corresponding surface properties. The behavior of the different materials was evaluated by determining equilibrium adsorption isotherms of two anionic dyes (Reactive Red 241 and Acid Blue 113) at different pH values. The results are compared with data previously obtained with commercial activated carbons subjected to the same treatments, and discussed in terms of the carbon surface chemistry and the interaction between the dye molecules and the adsorbent surface (dispersive and electrostatic interactions).     

Application of polyaniline as an efficient and novel adsorbent for azo dyes removal from textile wastewaters

In this work, application of polyaniline coated onto wood sawdust (PAni/SD) for the removal of methyl orange (MO) as a typical azo dye from aqueous solutions is introduced. The effects of some important parameters such as pH, initial concentration, sorbent dosage, and contact time on the uptake of MO solution were also investigated. In order to get a better comparison, adsorption experiments were also carried out using commercial grade of granulated activated carbon (GAC) and sawdust without coating (SD) at the same time. It was found that PAni/SD can be used to remove azo dyes such as MO from aqueous solutions very efficiently. Experimental data were analyzed by the Langmuir and Freundlich models of adsorption. Kinetic parameters for the adsorption of MO dyes for the selected adsorbents are also reported. In order to study the possibility of desorption for frequent application, chemical regeneration of the used adsorbents was also investigated. Desorption or recovery of dye and regeneration of adsorbent (PAni/SD) was found to be quite possible and of high performance. Application of modified sawdust with polyaniline for the removal of azo dye is very promising for textile wastewater treatment.     

羧基化石墨烯对4种离子型染料的吸附脱色

合成的羧基化石墨烯（G-COOH）用FT-IR进行表征,并对G-COOH用于水溶液中甲基紫、中性红、灿烂黄和茜素红4种离子型染料的吸附性能进行了研究。 考察了吸附剂用量、吸附时间、初始浓度以及溶液pH值等条件对吸附效果的影响。 同时,研究了甲基紫染料的脱附性能,结果表明,用NaOH/EtOH混合溶液洗脱甲基紫,洗脱率可达88.2%,洗脱后的G-COOH可再利用。 从热力学角度探讨得出,G-COOH对阳离子染料甲基紫和中性红的吸附行为能够较好的符合Langmuir等温吸附模型,而对阴离子染料灿烂黄和茜素红的吸附行为则能够较好的符合Freundlich等温吸附模型,计算的吸附参数表明,G-COOH对4种染料的吸附过程容易进行。 动力学研究表明,G-COOH对4种离子型染料的吸附行为均能较好的符合准二级吸附模型。 该实验研究表明,在处理染料废水时,G-COOH为相当优异的吸附剂。     

Removal of Reactofix Navy Blue 2 GFN from aqueous solutions using adsorption techniques

The wheat husk, an agricultural by-product, has been activated and used as an adsorbent for the adsorption of Reactofix Navy Blue 2 GFN from aqueous solution. In this work, adsorption of Reactofix Navy Blue 2 GFN on wheat husk and charcoal has been studied by using batch studies. The equilibrium adsorption level was determined to be a function of the solution pH, adsorbent dosage, dye concentration and contact time. The equilibrium adsorption capacities of wheat husk and charcoal for dye removal were obtained using Freundlich and Langmuir isotherms. Thermodynamic parameters such as the free energies, enthalpies and entropies of adsorption were also evaluated. Adsorption process is considered suitable for removing color, COD from waste water.     

Adsorption of Reactive Blue 4 dye from water solutions by carbon nanotubes: experiment and theory

Multi-walled and single-walled carbon nanotubes were used as nanoadsorbents for the successful removal of Reactive Blue 4 textile dye from aqueous solutions. The adsorbents were characterised by infrared and Raman spectroscopy, N(2) adsorption/desorption isotherms and scanning and transmission electron microscopy. The effects of pH, shaking time and temperature on adsorption capacity were studied. In the acidic pH region (pH 2.0), the adsorption of the dye was favourable using both adsorbents. The contact time to obtain equilibrium isotherms at 298-323 K was fixed at 4 hours for both adsorbents. The general order kinetic model provided the best fit to the experimental data compared with pseudo-first order and pseudo-second order kinetic adsorption models. For Reactive Blue 4 dye, the equilibrium data (298 to 323 K) were best fitted to the Liu isotherm model. The maximum sorption capacity for adsorption of the dye occurred at 323 K, attaining values of 502.5 and 567.7 mg g(-1) for MWCNT and SWCNT, respectively. Simulated dyehouse effluents were used to check the applicability of the proposed nanoadsorbents for effluent treatment (removal of 99.89% and 99.98%, for MWCNT and SWCNT, respectively). The interaction of Reactive Blue 4 textile dye with single-walled carbon nanotubes (SWCNTs) was investigated using first principles calculations based on density functional theory. Results from ab initio calculations indicated that Reactive Blue 4 textile dye could be adsorbed on SWCNT through an electrostatic interaction; these results are in agreement with the experimental predictions.     

Removal of structurally different dyes in submerged membrane fungi reactor—Biosorption/PAC-adsorption,membrane retention and biodegradation

The long-term performance of a submerged membrane fungi reactor was observed while a synthetic textile wastewater containing either or both of the two structurally different azo dyes was continuously fed. Compared to the Acid Orange II dye (simpler structure), higher biosorption but slower biodegradation of the polymeric dye (Poly S119) was observed in sterile batch tests. In the membrane bioreactor (MBR), although a relative abundance of fungi (66%) without any specific control of bacterial contamination could be maintained, unlike in pure fungus culture, enzymatic activity was below detection limit. Nevertheless, >99% removal of Poly S119 was consistently achieved under a dye loading of 0.1 g L⁻¹ d⁻¹ (HRT = 1 d). Comparison of the reactor-supernatant (SQ) and the membrane-permeate (PQ) qualities (31% improvement) revealed the significant contribution of the membrane to the overall removal (biosorption, cake layer filtration, biodegradation) of Poly S119. Contrary to the faster removal of Orange II in batch test, membrane-permeate quality revealed 93% removal of the dye in MBR (corresponding SQ = 82%). However, excellent (>99%) stable removal of Orange II or of both the dyes together, as well as stable enzymatic activity was observed following addition of powdered activated carbon (PAC) in the MBR. In accordance with real textile wastewater, dye contributed only 5% of the TOC loading (0.944 g L⁻¹ d⁻¹) in this study. In contrast to low TOC removal by fungi alone, the MBR containing mixed microbial community steadily achieved >98% removal, which improved further to >99% after PAC addition.     

Dye and its removal from aqueous solution by adsorption: A review

In this review article the authors presented up to-date development on the application of adsorption in the removal of dyes from aqueous solution. This review article provides extensive literature information about dyes, its classification and toxicity, various treatment methods, and dye adsorption characteristics by various adsorbents. One of the objectives of this review article is to organise the scattered available information on various aspects on a wide range of potentially effective adsorbents in the removal of dyes. Therefore, an extensive list of various adsorbents such as natural materials, waste materials from industry, agricultural by-products, and biomass based activated carbon in the removal of various dyes has been compiled here. Dye bearing waste treatment by adsorption using low cost alternative adsorbent is a demanding area as it has double benefits i.e. water treatment and waste management. Further, activated carbon from biomass has the advantage of offering an effected low cost replacement for non-renewable coal based granular activated carbon provided that they have similar or better adsorption on efficiency. The effectiveness of various adsorbents under different physico-chemical process parameters and their comparative adsorption capacity towards dye adsorption has also been presented. This review paper also includes the affective adsorption factors of dye such as solution pH, initial dye concentration, adsorbent dosage, and temperature. The applicability of various adsorption kinetic models and isotherm models for dye removal by wide range of adsorbents is also reported here. Conclusions have been drawn from the literature reviewed and few suggestions for future research are proposed.     

The removal of textile dyes by diatomite earth

The adsorption of some textile dyes by diatomite was investigated using Sif Blau BRF (SB), Everzol Brill Red 3BS (EBR), and Int Yellow 5GF (IY). Adsorption of these textile dyes onto diatomite earth samples was studied by batch adsorption techniques at 30 degrees C. The adsorption behavior of textile dyes on diatomite samples was investigated using a UV-vis spectrophotometric technique. The effect of particle size of diatomite, diatomite concentration, the effect of initial dye concentrations, and shaking time on adsorption was investigated. Adsorption coverage over the surface of diatomite was studied using two well-known isotherm models: Langmuir's and Freundlich's. These results suggest that the dye uptake process mediated by diatomite has a potential for large-scale treatment of textile mill discharges. According to the equilibrium studies, the selectivity sequence can be given as IY > SB > EBR. Values of the removal efficiency of the dyes ranged from 28.60 to 99.23%. These results show that natural diatomite holds great potential to remove textile dyes from wastewater.     

Adsorption of Safranin-T from wastewater using waste materials- activated carbon and activated rice husks

Textile effluents are major industrial polluters because of high color content, about 15% unfixed dyes and salts. The present paper is aimed to investigate and develop cheap adsorption methods for color removal from wastewater using waste materials activated carbon and activated rice husk-as adsorbents. The method was employed for the removal of Safranin-T and the influence of various factors such as adsorbent dose, adsorbate concentration, particle size, temperature, contact time, and pH was studied. The adsorption of the dye over both the adsorbents was found to follow Langmuir and Freundlich adsorption isotherm models. Based on these models, different useful thermodynamic parameters have been evaluated for both the adsorption processes. The adsorption of Safranin-T over activated carbon and activated rice husks follows first-order kinetics and the rate constants for the adsorption processes decrease with increase in temperature.     

A comparative adsorption study with different industrial wastes as adsorbents for the removal of cationic dyes from water

Four adsorbents have been prepared from industrial wastes obtained from the steel and fertilizer industries and investigated for their utility to remove cationic dyes. Studies have shown that the adsorbents prepared from blast furnace sludge, dust, and slag have poor porosity and low surface area, resulting in very low efficiency for the adsorption of dyes. On the other hand, carbonaceous adsorbent prepared from carbon slurry waste obtained from the fertilizer industry was found to show good porosity and appreciable surface area and consequently adsorbs dyes to an appreciable extent. The adsorption of two cationic dyes, viz., rhodamine B and Bismark Brown R on carbonaceous adsorbent conforms to Langmuir equation, is a first-order process and pore diffusion controlled. As the adsorption of dyes investigated was appreciable on carbonaceous adsorbent, its efficiency was evaluated by comparing the results with those obtained on a standard activated charcoal sample. It was found that prepared carbonaceous adsorbent exhibits dye removal efficiency that is about 80-90% of that observed with standard activated charcoal samples. Thus, it can be fruitfully used for the removal of dyes and is a suitable alternative to standard activated charcoal in view of its cheaper cost.     

Cationic dye adsorption by acrylamide/itaconic acid hydrogels in aqueous solutions

Acrylamide/itaconic acid (AAm/IA) hydrogels containing different quantities of itaconic acid have been irradiated with γ radiation. The hydrogels were used in an experiment concerning the adsorption of cationic dyes such as Basic Blue 9, Basic Violet 1 and Basic Blue 12. In the experiments of the adsorption of dyes from their synthetic aqueous solutions, type S adsorption isotherms were found. One mole of monomeric unit of AAm/IA hydrogels adsorbed 78.5–513.1 μmole of Basic Blue 9, 60.2–641.1 μmole of Basic Violet 1 and, 28.8–593.3 μmole of Basic Blue 12, while acrylamide hydrogel did not adsorb any cationic dye. As a result, it was shown that the AAm/IA hydrogels could be used as an adsorbent for water pollutants such as dyes, and immobilization of these organic contaminants in the hydrogels from waste water can solve one of the most important environmental problems of the textile industry. © 1997 John Wiley & Sons, Ltd.     

Adsorption and kinetic studies of cationic and anionic dyes on pyrophyllite from aqueous solutions

The adsorption of cationic Methylene Blue (MB) and anionic Procion Crimson H-EXL (PC) dyes from aqueous medium on pyrophyllite was studied. Changes in the electrokinetics of pyrophyllite as a function of pH were investigated in the absence and presence of multivalent cations. The results show that pyrophyllite in water exhibits a negative surface charge within the range pH 2-12. Pyrophyllite is found to be a novel adsorbent for versatile removal of cationic and anionic dyes. The negative hydrophilic surface sites of pyrophyllite are responsible for the adsorption of cationic MB molecules. The adsorption of anionic PC dye is possible after a charge reversal by the addition of trivalent cation of Al. Nearly 2 min of contact time are found to be sufficient for the adsorption of both dyes to reach equilibrium. The experimental data follow a Langmuir isotherm with adsorption capacities of 70.42 and 71.43 mg dye per gram of pyrophyllite for MB and PC, respectively. For the adsorption of both MB and PC dyes, the pseudo-second-order chemical reaction kinetics provides the best correlation of the experimental data.     

Effective removal of anionic dyes from aqueous solutions by novel polyethylenimine-ozone oxidized hydrochar (PEI-OzHC) adsorbent

The adsorption behavior of the anionic dyes Remazol Brilliant Blue R (RBBR) and Reactive Black 5 (RB5) from aqueous solutions by polyethylenimine ozone oxidized hydrochar (PEI-OzHC) was investigated. The adsorption capacities of both dyes increased with functionalization of PEI in the hydrochar adsorbent. The results of surface characterization (FTIR, BET, TGA, elemental analysis, and SEM) showed that PEI modification greatly enhanced the adsorbent surface chemistry with a slight improvement of adsorbent textural properties. In addition, the adsorption kinetics data showed an excellent adsorption efficiency as reflected in the high removal percentages of the anionic dyes. The Isotherm results indicated that RBBR and RB5 dye adsorption occurred via monolayer adsorption, and chemisorption was the rate-controlling step. The PEI-OzHC adsorbent possesses higher maximum Langmuir adsorption capacity towards RBBR (218.3 mg/g) than RB5 (182.7 mg/g). This increase in adsorption capacity is attributed to the higher number of functional groups in RBBR that interact with the adsorbent. This study reveals the potential use of adsorbents derived from pine wood hydrochar in municipal as well as industrial wastewater treatment. Furthermore, surface chemistry modification is proven as an effective strategy to enhance the performance of biomass-derived adsorbents.     

Fe3O4-CuO-activated carbon composite as an efficient adsorbent for bromophenol blue dye removal from aqueous solutions

Dye wastewater from industries is posing tremendous health hazards. The lethal dyes can be eliminated using nanomaterials and scientific approach like adsorption which is facile, cheap, safe as well as ecofriendly. Fe₃O₄-CuO-AC composite was prepared by a hydrothermal method and used for the removal of dyes in wastewater. The composite material was characterized by various techniques such as XRD, SEM, EDS, TEM and FT-IR. The Fe₃O₄-CuO-AC composite was used to treat five types of dyes in water. Fe₃O₄-CuO-AC composite showed the highest adsorption capability for bromophenol blue (BPB) dye. The effects of initial concentration, pH, the amount of adsorbent and temperature were also studied. The optimum conditions were found to be 20 ppm dye concentration, pH 9, an adsorbent dose of 0.06 gL^─1 at 65 °C. A removal efficiency of 97% was obtained for BPB dye during 120 min of adsorption. Kinetic studies indicated that a pseudo-second order is the most suitable model for the adsorption process. The Fe₃O₄-CuO-AC composite showed better adsorption capacity as compare to Fe₃O₄-AC except for the Methyl green dye. The maximum adsorption capacity was found to be 88.60 mg/g for BPB. Additionally, the thermodynamic parameters (ΔS°, ΔH° and ΔG°) showed that the process was spontaneous and exothermic. All the above results revealed that the Fe₃O₄-CuO-AC compositecan be an effective adsorbent for removing dyes from wastewater.     

Removal of malachite green from dye wastewater using mesoporous carbon adsorbent

Mesoporous carbon was synthesized for the removal of a cationic dye malachite green (MG) from aqueous solution. The studies were carried out under various experimental conditions such as contact time, dye concentration, adsorption dose and pH to assess the potentiality of mesoporous carbon for the removal of malachite green dye from wastewater. The sorption equilibrium was reached within 30 min. In order to determine the adsorption capacity, the sorption data were analyzed using linear form of Langmuir and Freundlich equation. Langmuir equation showed higher conformity than Freundlich equation. More than 99% removal of MG was reached at the optimum pH value of 8.5. From kinetic experiments, it was concluded that the sorption process followed the pseudo-first-order kinetic model. This study showed that mesoporous carbon can be recommended as an excellent adsorbent at high pH values.     

The adsorption of dyes used in the textile industry on mesoporous materials

An adsorbent material made with a silica lamellar mesoporous material treated with chitosan has been proved to be useful to adsorb both anionic and cationic dyes used in the textile industry. The two tested dyes Tectilon Blue (anionic) and Rhodamine B (cationic) have different adsorption kinetics reflecting a complex mechanism of the phenomenon. Furthermore, the adsorption capacity and interaction strength of Tectilon Blue is higher than those of Rhodamine B. Tectilon Blue molecules are situated with the molecular plane perpendicular to the adsorbent surface, whilst that of the Rhodamine B molecule is flat and parallel to the surface. The differences may be attributed to the different regions of the adsorbent surface on which the dyes are adsorbed because of their different electric charge.