Crystal growth and structure of MnGa2Te4

Single crystals of MnGa₂Te₄ were grown from the melt using the directional freezing technique. They crystallize in the monoclinic system, a=11.999(3), b=11.999(3), c=24.922(6) Å, β=104.01(2)°, Z=16 MnGa₂Te₄ units, space group C2/c. The structure was solved by direct methods and refined to R_w=0.035 for 791 observed reflections and to R_w=0.062 for 3067 independently measured reflections. Te atoms form an arrangement which is a superlattice of anion lattice of β-Cu₂HgI₄. On the contrary, the same model does not conform cation lattice, because 1/3 of metal atoms occupy positions displaced from tetrahedral sites.     

Diffraction study of Li2O·SiO2 glass with computer simulation

The structure of Li₂O·SiO₂ glass has been determined by the pair-function analysis of the radial distribution function (RDF) obtained by X-ray and neutron diffraction measurements. The structure models were constructed by the molecular dynamics method (MD). The calculated RDFs, the summation of the pair-functions of the model, were compared with the observed RDFs while varying the MD parameters. Taking advantage of the negative scattering length of Li for neutron diffraction, the glass structure was investigated in detail, and it was found that the chains of SiO₄ tetrahedra bend at 20 °, which is a little less than for the crystal (23.48 °). It is known that the larger the size of the alkali ions (Na⁺ → K⁺ → Cs⁺), the smaller the bending angle of the chains. It was found that this rule also applies to Li⁺.     

Molecular dynamics simulation of the mixed anion glasses Li4SiO4---Li3BO3

The structure and the mixed anion effect in the conductivity have been examined for the mixed anion glasses Li₄SiO₄---Li₃BO₃ by molecular dynamics (MD) simulation and X-ray diffraction (XRD) analysis. Structure factors derived from the MD simulation are in good agreement with those from derived from the XRD analysis of the actual glasses, showing that the MD simulation successfully reproduces the actual glass structure. Moreover, the enhancement of the diffusion coefficients of the Li⁺ ions in the middle of the composition range in the system Li₄SiO₄---Li₃BO₃ is simulated by the MD calculation. Structural analysis of the glasses derived from the MD simulation revealed that the increase in the halfwidth of the modified radial distribution function of the Li---O pairs due to the mixing of two ortho-oxoanions is one of the factors in the origin of the mixed anion effect in the conductivity.     

X/g-C3N4(X=g-C3N4、AlN及GaN)异质结光催化活性的理论研究

本文采用基于密度泛函理论的第一性原理平面波超软赝势方法,研究了单层g-C₃N₄以及X/g-C₃N₄(X=g-C₃N₄、AlN及GaN)异质结的稳定性、电子结构、功函数及光学性质。结果表明,X/g-C₃N₄异质结的晶格失配率和晶格失配能极低,说明X/g-C₃N₄具有优异的稳定性。与单层g-C₃N₄相比,X/g-C₃N₄的带隙均减小,态密度的波峰和波谷均大幅提高且出现了红移现象,处于激发态的电子数量增加,使得电子跃迁变得更为容易,表明构建异质结有利于提高体系对可见光的响应能力。此外,X/g-C₃N₄的功函数均减小且在界面处形成了内建电场,有效抑制了光生电子-空穴对的复合,这对载流子的迁移以及光催化能力的提高大有裨益。其中,GaN/g-C₃N₄的功函数最小,在界面处存在电势差形成了内建电场且红移现象最明显,可推测GaN/g-C₃N₄的光催化性能最好。因此,本文提出的构建异质结是提高体系光催化活性的有效手段。     

A new method for fabricating water repellent silica films having high heat-resistance using the sol–gel method

There has been a great demand in the field of kitchen appliances to develop transparent water repellent films which have high heat-resistance around 300°C. However, those films have not been obtained by conventional sol–gel methods. In this paper, we propose a new method for fabricating transparent water repellent films with high heat-resistance using the sol–gel method, in which silicon or germanium substrates were coated with a solution including tetraethoxysilane (Si(OC₂H₅)₄) and (2-perfluorooctyl)ethyltrimethoxysilane (CF₃(CF₂)₇C₂H₄Si(OCH₃)₃), followed by ‘ammonia-treatment' and annealed at 300°C. The contact angles of water on the ammonia-treated film maintained its initial value, 110° after the heat treatment at 300°C for 250 h while those on the untreated film decreased to 70°, indicating that the ammonia-treatment improves heat-resistance on the film. The mechanism of ammonia-treatment was inferred from FT-IR results; the ammonia-treatment should accelerate hydrolysis and polymerization of FAS and TEOS molecules, resulting in high density of siloxane bonds between FAS and silica glass. These bonds suppress the evaporation of FAS molecules from the film during the heat treatment at 300°C, thus the film has high heat-resistance.     

Epitaxial growth of the CoFe2O4 film on SrTiO3 and its characterization

Cobalt ferrite (CoFe₂O₄) thin film is epitaxially grown on (0 0 1) SrTiO₃ (STO) by laser molecular beam epitaxy (LMBE). The growth modes of CoFe₂O₄ (CFO) film are found to be sensitive to laser repetition, the transitions from layer-by-layer mode to Stranski–Krastanov (SK) mode and then to island mode occur at the laser repetition of 3 and 5 Hz at 700 °C, respectively. The X-ray diffraction (XRD) results show that the CFO film on (0 0 1) SrTiO₃ is compressively strained by the underlying substrate and exhibits high crystallinity with a full-width at half-maximum of 0.86°. Microstructural studies indicate that the as-deposited CFO film is c-oriented island structure with rough surface morphology and the magnetic measurements reveal that the compressive strained CoFe₂O₄ film exhibits an enhanced out-of-plane magnetization (190 emu/cm³) with a large coercivity (3.8 kOe).     

Distribution of oxidation states of Cr ions in Ca or Ca/Mg co-doped Cr:Y3Al5O12 single-crystal fibers with nitrogen or oxygen annealing environments

The valence states of Cr ions in Ca or Ca/Mg co-doped Cr:Y₃Al₅O₁₂ (YAG) single-crystal fibers are studied. The fibers were grown using the laser-heated pedestal growth method, followed by annealing treatments up to 1500 °C. The concentrations of the Cr³⁺ and Cr⁴⁺ ions in octahedral and tetrahedral sites in oxygen or nitrogen environments were characterized. Above 700 °C, migration of Cr⁴⁺ between octahedral and tetrahedral sites takes place; its relative stabilization energy was estimated. For Ca,Cr:YAG annealed in an oxygen or nitrogen environment, it was 0.25 and 0.3 eV, respectively. For Mg,Ca,Cr:YAG annealed in oxygen or nitrogen, it was 0.47 and 0.49 eV, respectively. For the Ca,Cr:YAG crystal fiber (Ca/Cr=113.1%) with oxygen annealing, about 35% and 2.5% of Ca ions took part in charge compensation for Cr⁴⁺ in the octahedral and tetrahedral sites, respectively. The density of oxygen vacancies depends on the concentration of Ca ions. The estimated ratios of the unreacted oxygen vacancies to total oxygen vacancies were about 63% and 88% for oxygen and nitrogen annealing, respectively. The main limitation on the concentration of Cr⁴⁺ in the tetrahedral site of YAG is the presence of unreacted oxygen vacancies.     

Structural, thermal and dielectric studies on a new solution grown 4-dimethylaminopyridinium dihydrogen phosphate crystal

Single crystals of 4-dimethylaminopyridinium dihydrogen phosphate (DMAPDP) (C₇H₁₃N₂PO₄) were grown by the solvent evaporation method. The three-dimensional structure was solved by the single-crystal X-ray diffraction method which belongs to triclinic crystal system and the molecular arrangements in the crystal were studied. The thermal behaviour was investigated using differential scanning calorimetry (DSC) and no phase transition was identified in the temperature region −150 to 230 °C. The thermal parameters—thermal diffusivity (), thermal effusivity (e), thermal conductivity (K) and heat capacity (C_p) of DMAPDP were measured by an improved photopyroelectric technique at room temperature. Dielectric constant and dielectric loss of the grown crystal were evaluated for the frequency range 1–200 KHz in the temperature region 28–135 °C. The Vicker's hardness was measured as 42.2 for a load of 98.07 mN. The laser induced surface damage threshold of DMAPDP crystal was found to be 4.8 GW/cm² with nanosecond Nd:YAG laser.     

Research on growth and self-frequency doubling OF Nd:ReCOB (Re=Y OR Gd) crystals

Large (up to 45mm in diameter and 50mm in length) ReCa₄O(BO₃)₃ (ReCOB) and Nd:ReCOB (Re=Y or Gd) crystals with high optical quality were grown by well designed procedures. Crystal orientation was carefully determined. Based on the measurements of refractive indices the phase matching (PM) figures for both crystals were calculated. Theoretical calculation of the spatial distribution of the effective nonlinear coefficients, which show an asymmetric feature, was carried out to determine the optimal PM orientations which were experimentally confirmed, i.e. (66.3°, 134.4°) and (64.5°, 33.5°) for GdCOB and YCOB respectively.     

A study of the chemical reactions involved in Li–Ca–N system

The chemical reactions and phases involved in the potential flux system of Li–Ca–N for the growth of bulk GaN crystals have been investigated under varying conditions. It is found that no preferential nitrification of Li or Ca by N₂ in Li–Ca melts at 500 °C. Only the ternary compound LiCaN is identified in the Li–Ca–N system under the present experimental conditions. Static N₂ pressures are found to enhance the formation of LiCaN compared to an N₂ stream. LiCaN forms from two possible pathways: one is a modified metathesis chemical reaction represented by Li₃N+Ca→LiCaN+2Li, and the other is a combination chemical reaction represented by Li₃N+Ca₃N₂→3LiCaN. The formation of LiCaN by the metathesis reaction is thermodynamically favored over the other pathway. In addition, the formation of LiCaN might benefit from a slightly larger initial amount of Li₃N compared with Ca or Ca₃N₂.     

TiO2-SiO2 monolithic glass formation from sol-gel

This study demonstrates that hydrolysis should be carried out in a step manner in gel synthesis. The key to the increase in the amount of water added is the control of the hydrolysis rate of Ti(OC₄H₉)₄. The hydrolysis of Si(OC₂H₅)₄ can be carried out at about 75°C. The amount of added water (γ_WI), which varied with TiO₂ content (in mol%), was about 64–88% of the total amount of added water. The hydrolysis reaction should be performed at room temperature while Ti(OC₄H₉)₄ is added. The total amount of added water (γ_W) is related to the amount of solvent (R). For example, if TiO₂ is 40mol%, γ_W will vary from 3.2 to 8.0 when R varies from 0.8 to 2.0. The amount of added water was affected by the distribution of solvent in the metal alkoxides. The amount of added water can be increased when R_Si(OC2H5)4 = 1, R_Ti(OC4H9)4 > 1. The rate of rise in temperature of the thermolysis of the dried gel should be less than 10°C per hour, and the heat treatment temperatyre is related to the TiO₂ content (in mol%). Gel glasses without devitrification can only be obtained by thermolysis at 600°C from the gel with no less than 20 mol% TiO₂.     

g-C3N4催化石墨化碳质材料的制备及光催化性能研究

通常采用以氢氧化物作为造孔剂,过渡金属硝酸盐或氯化物作为石墨化催化剂的传统两步法策略制备多孔石墨化碳材料。然而制备过程中多涉及有毒和腐蚀性试剂,且多步骤的过程耗时较长。本文以双氰胺为原料通过热缩聚反应得到g-C₃N₄,采用高铁酸钾为催化剂一步法实现g-C₃N₄的同步碳化-石墨化,并研究其光催化性能。与传统的两步法相比,该方法耗时少、效率高、无污染。与初始的g-C₃N₄材料相比,石墨化g-C₃N₄衍生碳质材料不仅显著改善了可见光的吸收,而且大大增强了光催化活性。研究了不同石墨化温度对g-C₃N₄衍生碳质材料在可见光下降解甲基橙溶液的影响。700 ℃下制备的衍生碳质材料的降解率为12.4 mg/g。光电化学测试结果表明,多孔g-C₃N₄衍生碳质材料的光生载流子密度、电荷分离和光电流(提高了5.4倍)均得到显著提高。因此,该简便、灵活方法为提高g-C₃N₄衍生碳质材料的吸附和光催化性能提供了一种有前景的、高效的途径。     

铒掺杂g-C3N4催化剂的合成及其红光催化降解活性的研究

石墨相氮化碳(g-C₃N₄)的研究已成为光催化领域热点。本文以三聚氰氨为前驱体,采用甲醇回流法制备Er掺杂的g-C₃N₄催化剂。利用扫描电镜(SEM)、X射线光电子能谱(XPS)、X射线衍射仪(XRD)、紫外-可见-近红外分光光度计(UV-Vis-NIR DRS)、傅里叶红外光谱仪(IR)、荧光光谱(PL)、物理吸附(N₂-physisorption)及共聚焦显微镜(CLSM)等手段对Er/g-C₃N₄催化剂进行系统表征。结果表明,稀土金属Er高分散于g-C₃N₄上,促使氮化碳表面氮空穴的产生。Er掺杂优化了氮化碳的能带结构,增强了其对可见光的吸收,提升电子-空穴对的分离效率,此外还发现Er/g-C₃N₄具有较强的上转换能力。在660 nm红光LED照射下,对罗丹明B的水溶液进行光催化降解,发现Er/g-C₃N₄的降解速率是g-C₃N₄的2.0倍,且发现超氧自由基为该体系中的主要活性物种。     

The effect of MgO on the thermodynamics of the Fe/Fe-redox equilibrium and the incorporation of iron in soda-magnesia-aluminosilicate melts

Melts with the basic compositions 10Na₂O · 10MgO · xAl₂O₃ · (80−x)SiO₂ (x=0, 5, 10, 15 and 20), 10Na₂O · xMgO · 10Al₂O₃ · (80−x)SiO₂ (x=5, 10, 15 and 20) and xNa₂O · 10MgO · 10Al₂O₃ · (80−x)SiO₂ (x=5, 10 and 15) all doped with 0.25 mol% Fe₂O₃ were studied using square-wave voltammetry. The temperatures applied were in the range of 1000–1600 °C. The square-wave voltammograms recorded show peaks caused by the reduction of Fe³⁺ to Fe²⁺. The attributed peak potentials measured decreased linearly with decreasing temperatures. Increasing the MgO-concentration led to more negative peak potentials. Introducing alumina in the melt first resulted in less negative peak potentials. If the molar Al₂O₃-concentration is equal to that of Na₂O (=10 mol%) the peak potentials are least negative. Further increase of the Al₂O₃-concentration led to more negative peak potentials. The variation of the Na₂O-concentration led to a maximum in the peak potentials at an Na₂O-concentration of 10 mol%. An empirical formula which allows the calculation of standard potentials from the chemical composition is proposed. Furthermore, a structural explanation for the effect of the chemical composition is given. Especially, the incorporation of Al₂O₃ as AlO₄⁻-tetrahedra at [Al₂O₃] < [Na₂O] and as network modifier at larger concentrations was structurally explained by the similarities of Fe²⁺ and Mg²⁺, with respect to cation radii and metal–oxygen bond lengths.     

Synthesis of fluorine doped silica gel and its properties at high temperature

Fluorine doped silica gels were synthesized by using the sol-gel processes of (A) SiF₄(g) and H₂O(1) and (B) the mixed solution of Si(OC₂H₅)₄, C₂H₅OH, H₂O and H₂SiF₆. By the former process we obtained a gel of relatively high fluorine content (8–12 at.%F), while we could synthesize the gel of 0–12 at.% F by adjusting the F/Si ratio of the starting solution mixtures by the latter process.

The defluorination behavior and the structural change of these gels at high temperature were studied by heating-mass spectrometry, IR and ESR measurements. The results revealed the following: (1) defluorination by liberation of SiF₄(g) was admitted from temperatures at about 400°C and was controlled by the diffusion of fluorine in the gel bulk. (2) The peak separation analysis for the IR band of 1300-900 cm⁻¹, where the stretching vibrations of Si---O and Si---F appear, showed that the change of the band shape resulted from the increase or the decrease of the Si---F bonds and the change of the bond angle of Si---O---Si as well as the change of the force constant accompanied by fluorination or defluorination. (3) The defects of the Si E′ center were induced by X-ray irradiation depending on the degree of the defluorination, and were reduced by the heat treatment. However, with the heat treatment at temperatures higher than 1000°C, the E′ center increased again. The IR spectra suggest that this behavior might correspond to the gel-glass trasition.     

非金属掺杂改性g-C3N4光催化降解水中有机污染物的研究进展

近年来,石墨相氮化碳(g-C₃N₄)以其合适的带隙宽度、丰富的活性位点和成本低廉等优点,成为新兴的可见光响应非金属光催化剂,被广泛应用于光催化降解有机污染物领域。然而,纯g-C₃N₄对可见光的吸收效率较低且光生电子和空穴复合速率快,导致其光催化活性处于较低水平。基于g-C₃N₄的非金属特性,通过非金属掺杂可以有效提高g-C₃N₄的光催化性能,引起了学者们的广泛关注。本文介绍了目前非金属掺杂g-C₃N₄复合材料常见的制备方法,着重归纳了不同类型的非金属掺杂g-C₃N₄光催化降解水中有机污染物的相关研究进展,探讨其作为光催化剂在可见光条件下降解有机污染物的相关机理。最后,提出目前g-C₃N₄基复合材料在光催化降解水中有机污染物中所面临的挑战,旨在为非金属掺杂g-C₃...     

Calculation of NMR shieldings and other properties for three and five coordinate Si, three coordinate O and some siloxane and boroxol ring compounds

Valuable information on the geometric and electronic structure of both predominant and defect species in the bulk and on the surface of amorphous SiO₂ can be obtained from solid state ²⁹Si and ¹⁷O NMR. Most previous NMR.studies have made assignments of structure types to NMR signals by relying on a comparison to crystalline reference materials. Using the quantum mechanical technique of Coupled Hartree-Fock Perturbation Theory (CHFPT) we can directly calculate NMR shielding tensors, σ, for Si and O and electric field gradients tensors, q for O in silicates. Previous CHFPT calculations on (SiH₃)₂O at Si---O---Si = 180° to 140° semiquantitatively reproduced observed trends in σ for SiO₂ polymorphs. These calculations have been improved and extended to Si---O---Si = 120° in (SiH₃)₂O and to the small siloxane rings H₄Si₂O₂, H₆Si₃O₃, H₈,Si₄O₄ which are models for the ring structures which may occur in the bulk and surface of amorphous SiO₂. Thus, predictions can be made of the ¹⁷O and ²⁹Si NMR characteristic of such species. We have also calculated NMR shieldings and other properties for three and five coordinate Si and for three coordinate O. The ²⁹Si NMR shielding increases with coordination, as expected, and five coordinate Si shows an anisotropy which although large is still smaller than that inferred from spin-lattice relaxation times in silicate melts. O q values are also calculated for (BH₂)₂O and H₃B₃O₆. The results are consistent with O EFGs and Raman frequencies observed in B₂O₃ glass, supporting a boroxol ring model.     

Growth and self-frequency doubling laser output of Nd : Ca4Gd0.275Y0.725O(BO3)3 crystal

In this letter, Nd : Ca₄Gd_0.275Y_0.725O(BO₃)₃ (Nd : GdYCOB) single crystal with good optical quality and large size has been grown by the Czochralski method. The absorption and fluorescence spectra have been measured. The self-frequency doubling (SFD) laser output of Nd : GdYCOB at 0.53 μm has been demonstrated when a Nd : GdYCOB crystal sample with dimensions of 3 mm×3 mm×7 mm (the phase-matched angle is θ=78.8°, Φ=90°) is pumped by a cw Ti : sapphire laser.     

Li conductivity in lithium niobate: silica glasses

Glasses of composition 65 mol% LiNbO₃:: 35 mol% SiO₂ have been shown to be Li⁺ ion conductors with a conductivity at 200°C > 1 × 10⁻⁵ (η cm)⁻¹ and an activation energy of 0.54 eV. The addition of approximately 0.1 mol% Fe₂O₃ leads to an enhancement of conductivity to ≈10⁻³ (η cm)⁻¹ at 200°C and an activation energy of 0.67 eV. The effect of Fe is shown to be in the control of microstructure in the glass, with Fe₂O₃ concentrations < 1 mol% acting as a grain growth inhibitors and larger concentrations acting as a nucleating agents. A model for this process based on the expected stoichiometry of the melt and the effect of Fe²⁺ and Fe³⁺ in charge compensation is in excellent agreement with experimental data from electron spin resonance.     

Static B NMR studies of the short range order in alkali metal modified B2S3 glasses

The ¹¹B NMR spectra of xRb₂S+(1−x)B₂S₃ glasses in the range 0x0.75 and of xCs₂S+(1−x)B₂S₃ glasses in the range 0x0.60 are reported. The addition of Rb₂S to B₂S₃ creates on average approximately two and one-half tetrahedral borons for each added sulfur ion, whereas it is found that the addition of Cs₂S creates approximately 2 tetrahedral borons for each added sulfur ion. This behavior while more similar to that seen in the alkali borate glasses, contrasts that seen in the Na and K thioborate glasses, where six to eight and three, respectively, tetrahedral borons are formed for every sulfide anion added to the glass. These findings are supported by the IR and ¹¹B NMR spectra of the di-thioborate polycrystals (c-Rb₂S:2B₂S₃ and c-Cs₂S:2B₂S₃) whose structures appear to be comprised of two BS₄ tetrahedrals and two BS₃ trigonals (N₄0.5) like that in the alkali di-borate phases for both Rb and Cs. Unlike the ¹¹B NMR resonances of the sodium thioborate glasses where a single sharp line is observed for the tetrahedral boron site and a single quadrupolar broadened line is observed for all the trigonal sites, a third resonance line is observed at high alkali fractions for the rubidium and cesium thioborate glasses. This new structural feature may arise from asymmetric MBS₂ (meta-thioborate groups) or tetrahedral boron groups possessing a non-bridging sulfur.