共查询到20条相似文献,搜索用时 578 毫秒
1.
2.
惯性平台系统火箭橇试验数据处理方法 总被引:2,自引:1,他引:1
火箭橇试验具有产生大过载、高速度、强振动和冲击等综合条件的能力,可以在综合环境条件下对惯性测量装置的功能和精度进行验证.针对惯性平台系统开展了3 km火箭橇轨道的功能验证试验,对振动传感器的数据进行了过载分析和振动量级的谱分析.研究了惯性平台系统火箭橇试验后的数据处理方法,包括振动传感器对橇体运行的过载和振动量的分离方法,遮光板光电组件的位置和速度微分方法,以及惯性平台系统的导航算法等,并通过数据比较,对惯性平台系统的性能和功能进行评价.由于遮光板外测系统的采样时间和观测量与捷联惯性测量装置不同,还探讨了试验后观测信息之间的转换、同一时刻不同信息数据的比较等数据处理方法,通过数据比较验证了惯性平台系统在火箭橇试验时的功能正常.该研究对惯性平台系统进一步开展精度验证和误差系数的分离奠定了基础. 相似文献
3.
旋翼激励是直升机振动的主要源头,影响直升机驾驶员操纵性、机上人员舒适性及结构疲劳寿命。振动问题一般在试飞过程中暴露出来,问题处理和解决往往需要大的周期和代价,影响直升机研制。直升机振动响应预计是解决振动问题的主要手段之一,可以在早期发现振动问题,方便在型号研制早期开展优化设计或解决预案。本研究基于机体动力学仿真模型,以固定坐标系下的桨毂中心振动载荷作为输入,得到机体关键位置的振动响应,形成旋翼激励下直升机振动响应预测的方法。通过某直升机在尾桨激励下关键位置响应预计与实测数据对比分析,表明该方法得到的振动响应随速度的变化规律与实测数据一致,精度满足工程需要。该方法在新机振动响应分析、振动问题排查及振动控制方案制定等工作中具有较高的工程价值。 相似文献
4.
激波风洞地面试验对高超声速飞行器高焓气动特性研究至关重要, 而高精度气动力测量是其中的关键技术. 在脉冲型激波风洞中进行测力试验时, 风洞起动时流场瞬间建立, 对测力系统会产生较大的冲击. 测力系统在瞬时冲击作用下受到激励, 系统的惯性振动信号在短时间内无法快速衰减, 天平的输出信号中会包含惯性振动干扰量, 导致脉冲型风洞测力试验精准度的进一步提高遇到瓶颈. 为了解决短试验时间内激波风洞快速准确测力问题, 发展高精度的动态校准技术是提升受惯性干扰天平性能的关键方法. 因此, 本文采用循环神经网络对天平动态校准数据进行训练和智能处理, 旨在消除输出动态信号中的振动干扰信号. 本文对该方法进行了误差分析, 验证了该方法的可靠性, 并将该方法应用于激波风洞测力试验中, 切实有效降低了惯性振动对天平输出信号的干扰影响. 根据智能模型的样本验证分析, 各分量载荷相对误差比较小, 其中高频轴向力分量处理结果的相对误差约1%. 在风洞试验数据验证中, 也得到了比较理想的结果, 同时与卷积神经网络模型处理的结果进行了对比分析. 相似文献
5.
针对某型机定型试飞中遇到的跨音速等幅振动现象,对该机的颤振分析和试飞实测振动数据进行了研究.结果表明,该型飞机跨音速等幅振荡现象主要是由于外挂物连接间隙引起的,文中对采取的排故措施进行了描述,验证试飞结果表明该振动现象已被排除.从而保证了定型试飞的顺利进行. 相似文献
6.
为了提高陀螺加速度计在线振动条件下的标定精度,提出了陀螺加速度计在线振动台上的进动整周期的测试方法。该方法将陀螺加速度计正倒置安装后,在静态和线振动状态下分别测量陀螺加速度计进动整周期中的相关时间数据,计算出陀螺加速度计进动整周期的平均角速率,通过平均角速率与陀螺加速度计模型输出间的积分关系,推导出了陀螺加速度计在线振动台上的标定误差模型,辨识出了加速度计的零偏、标度因子、二次项系数和三次项系数。该方法抑制了陀螺加速度计输出的平均角速率误差,能够提高陀螺加速度计在线振动台上测试的精度。最后进行了算法验证,验证了该方法能够准确的辨识出加速度计的各项误差模型系数,辨识精度达到10?7,提高了陀螺加速度计在线振动台上的标定精度。 相似文献
7.
8.
研究了流体负载下的无穷大双周期加强板, 在周期谐振力作用下的振动响应和声辐射,并提出了一种基于有限元和空间波数法的半解析半数值方法. 首先利用有限元的方法对周期结构进行单元离散, 并将结构对薄板的作用力等效为节点力的作用. 然后通过周期结构的振动方程, 结合薄板与结构的位移边界条件, 建立了节点力与薄板节点位移的函数方程. 最后应用空间波数法和傅里叶变换, 并采用数值计算的方法求解出薄板的节点位移, 得到了周期加强板关于离散节点位移的振动和辐射声压方程. 在数值算例中, 对该方法的正确性进行了验证, 并且分析了周期结构对薄板的振动和声辐射的影响. 相似文献
9.
10.
11.
对《力学》中的物体自由度进行多方面分析,以深化教学、提高学生正
确分析物理问题的能力.使用实际教学分析的研究方法,在《力学》范围内讨论自由度与坐标、
自由与约束的关系并得以下结论:
(1) 同一物体的自由度随其所在的``空间'不同而不同, 不因坐标系的选取不同而
异, 在同类参考系中不因参考系的动静而有别;(2)自由度遵循叠加原理.
讨论了质点系的总自由度及相关计算问题,并指出研究《力学》中自由度的意义. 相似文献
12.
13.
14.
Tibor Javor 《Experimental Mechanics》1968,8(4):171-176
The present paper deals with development and design of new methods utilizing Wiedemann's effect for determination of state of strain in building structures. Wiedemann's effect and some features of torsional strain of magnetic field are the basis of new experimental method. Especially the point electromagnetic strain gages using the effect of pure torsion of electromagnetic field to enable universal examination. For strain-gage measurements, almost all physical quantities are used which can be related to the variation in length of the structures. From the electric strain measurements, the most commonly used methods are the measurements by resonance-wire strain gages or by electric-resistance strain gages. In this paper, electromagnetic strain gages are discussed using the Wiedemann effect, and the author describes some new measuring equipment and his own suggestions and methods based on an application of this effect. 相似文献
15.
16.
17.
It is well known that the problem on nonseparating potential flow of an incompressible fluid about an array of profiles reduces to an integral equation for a certain real function, determined on the contours of the profiles of the array. As such a function one can take, as was done, for instance, in [1–5], the relative velocity of the fluid on the profiles of the array. For arrays of profiles of arbitrary shape it is necessary to solve the corresponding integral equation numerically. In the particular examples of the calculation of aerodynamic arrays that are available [1–3] the numerical methods used were based on the approximate evaluation of contour integrals by rectangle formulas. As investigations showed, sizeable errors arose thereby in the approximate solution obtained, these being especially significant in the case of curved profiles of relatively small bulk. In the present paper a method for the numerical solution of the integral equation obtained in [5] is proposed. The method is based on the replacement of a profile of the array with an inscribed N polygon, the length of whose sides is of the order N–1 and whose internal angles are close to . Convergence with increasing N of the numerical solution to an exact solution of the integral equations at the reference points is demonstrated. Examples of the calculation are given.Novosibirsk. Translated from Izvestiya Akademii Nauk SSSR. Mekhanika Zhidkosti i Gaza, No. 2, pp. 105–112, March–April, 1972. 相似文献
18.
19.