High-voltage aqueous symmetric electrochemical capacitor based on Ru0.7Sn0.3O2·nH2O electrodes in 1 M KOH

A mild hydrothermal process is applied to synthesize hydrous ruthenium–tin binary oxides (Ru_0.7Sn_0.3O₂·nH₂O) with good capacitive performance in alkaline system. Then, a symmetric electrochemical capacitor (EC) is fabricated based on the as-synthesized Ru_0.7Sn_0.3O₂·nH₂O material and 1 M KOH aqueous electrolyte. Electrochemical performance of the symmetric EC is investigated by cyclic voltammetry, galvanostatic charge–discharge and electrochemical impedance spectroscopy tests. Electrochemical tests demonstrate that the symmetric EC surprisingly can operate with a high upper cell voltage limit of 1.45 V in 1 M KOH electrolyte. Maximum specific capacitance and energy density of the symmetric aqueous EC are approximately 160 F/g and 21 Wh/kg, respectively, delivered at a current density of 1.25 A/g. And the specific energy density decreases to approximately 15 Wh/kg when the specific power density increases up to approximately 1,770 W/kg. The promising specific energy and power densities are obtained simultaneously for the unwonted symmetric EC due to its larger operating potential range. Moreover, the symmetric EC exhibits electrochemical stability with 85.2% of the initial capacitance over consecutive 1,000 cycle numbers.     

Volumetric properties of H2O, D2O, and methanol in acetonitrile at 278.15—318.15 K

The densities of H₂O, D₂O, and MeOH solutions in acetonitrile with the solute concentrations up to 0.07 molar fractions at 278.15, 288.15, 298.15, 308.15, and 318.15 K were measured using vibrating-tube densimetry with an error 8·10^–6 g cm^–3. The limiting partial molar volumes for the H/D isotopomers of water and IaII in acetonitrile (V^– ₂ ) and the isotope effects in V^– ₂ and in excess molar volumes of acetonitrile—water mixtures were calculated. Molecules of H₂O, D₂O, and IaII form associates with acetonitrile molecules via hydrogen bonds. The associates have the packing volumes close to those in the individual solute. The water and methanol molecules were assumed to be incorporated into the acetonitrile structure without substantial changes in the latter. However, this process results in some compression of the system with a simultaneous increase in its expansibility.     

The mechanism and kinetics of energy transfer processes in the Xe–CCl4–M (M=CH4, C2H2, C2H4, C2H6 C3H6 and C3H8) mixtures irradiated by xenon resonance light

The mechanism and kinetics of energy transfer from Xe(6s[3/2]₁) resonance state (E=8.44 eV) to selected hydrocarbon molecules have been investigated by XeCl(B–X) (λ_max=308 nm) fluorescence intensity measurements at stationary conditions in Xe–CCl₄–M systems. Steady-state analysis of the fluorescence intensity dependence on the xenon and M pressure at constant CCl₄ concentration shows that these process occur in the two- and three-body reactions: Xe(6s[3/2]₁⁰)+M→products, Xe(6s[3/2]₁⁰+M+Xe→products. The two- and three-body rate constants for these reactions have been found (see Table 1Table 1. Experimental parameters of Eq. (8)found by least square method in Xe–CCl₄–C₂H₂ and Xe–CCl₄–C₂H₄ systems for chosen xenon pressures in the range 25–150 Torr. Linear correlation coefficients (R) are also shown     

4.

Electrocatalytic activity and stability of Ti/IrO2 + MnO2 anode in 0.5 M NaCl solution     

Xian-Liang Zhou  Zhi-Guo Ye  Xiao-Zhen Hua  Ai-Hua Zou  Ying-Hu Dong 《Journal of Solid State Electrochemistry》2010,14(7):1213-1219

Ti/IrO₂(x) + MnO₂(1-x) anodes have been fabricated by thermal decomposition of a mixed H₂IrCl₆ and Mn(NO₃)₂ hydrosolvent. Cyclic voltammetry (CV) and polarization curve have been utilized to investigate the electrochemical behavior and electrocatalytic activity of Ti/IrO₂(x) + MnO₂(1-x) anodes in 0.5 M NaCl solution (pH = 2). Ti/IrO₂+MnO₂ anode with 70 mol% IrO₂ content has the maximum value of q*, indicating that Ti/IrO₂(0.7) + MnO₂(0.3) anode has the most excellent electrocatalytic activity for the synchronal evolution of Cl₂ and O₂ in dilute NaCl solution. Tafel lines displayed two distinct linear regions with one of the slope close to 62 mV dec⁻¹ in the low potential region and the other close to 295 mV dec⁻¹ in the high potential region. Electrochemical impedance spectroscopic is employed to investigate the impedance behavior of Ti/IrO₂(x) + MnO₂(1-x) anodes in 0.5 M NaCl solution. It is observed that as the R _ct, R _s and R _f values for Ti/IrO₂(0.7) + MnO₂(0.3) anode become smaller, electrocatalytic activity of Ti/IrO₂(0.7) + MnO₂(0.3) anode becomes better than that of other Ti/IrO₂ + MnO₂ anodes with different compositions. Ti/IrO₂(0.7) + MnO₂(0.3) anode fabricated at 400 °C has been observed to possess the highest service life of 225 h, whereas the accelerated life test is carried out under the anodic current of 2 A cm⁻² at the temperature of 50 °C in 0.5 M NaCl solution (pH = 2).     

5.

One-Pot Reduction of Sulfoxides with NaBH4, CoCl2 · 6H2O Catalyst,and Moist Alumina     

Shigetaka Yakabe  Masao Hirano  Takashi Morimoto 《合成通讯》2013,43(15):2251-2255

Sulfoxides are reduced by a combination of sodium borohydride, a catalytic amount of cobalt(II) chloride hexahydrate, and chromatographic neutral alumina preloaded with a small amount of water (moist alumina) in hexane to produce the corresponding sulfides in good to excellent yields under mild conditions. An interesting structural influence of sulfoxides on their reactivity is observed.

Keywords: Cobalt(II) chloride hexahydrate, moist alumina, reduction, sodium borohydride, sulfoxide

Additional information

ACKNOWLEDGMENTS

The authors thank Dr. Akira Yoshida (Tokyo City University, Instrumental Analysis Center) for his help in carrying out the SEM experiment. The authors also thank Tae Tokuhata for helpful discussions.     

6.

Spectral and intramolecular charge transfer properties in terminal donor/acceptor-substituted all-trans-α,ω-diphenylpolyenes and α,ω-diphenylpolyynes     

Ma X  Yan L  Wang X  Guo Q  Xia A 《Physical chemistry chemical physics : PCCP》2011,13(38):17273-17283

The absorption spectra and intramolecular charge transfer (CT) properties of terminal donor/acceptor-substituted all-trans-α,ω-diphenylpolyenes (DPE) and α,ω-diphenylpolyynes (DPY) molecules with different conjugated bridge length and substitution modes were investigated by using quantum chemical calculations. We calculated the ground state structures and energy of two series of terminal donor/acceptor DPE and DPY by DFT method. The dependence of conjugation length and substitution modes of the electronic absorption spectra was obtained by TDDFT calculation. The hybrid-GGA XC-functional PBE0 employed in this work was selected from several functionals by comparing the calculated electronic spectral data with experimental value. The CIS-based generalized Mulliken-Hush (GMH) approach was further used to calculate coupling values H(AD) of the CT process. The calculation shows that both the HOMO-LUMO energy gaps and average bond length alternations between unsaturated multiple (C≡C and C=C) and saturated single bonds (C-C) decrease regularly with the extension of conjugation. The effective conjugated length (ECL) of DPE and DPY with the same order MM > MP/PM > PP is found together with the regular red shift of the electronic absorption spectra with the extension of conjugation, resulting from the different π-electron delocalization and conjugation efficiency. The GMH analysis further suggests that the CT process in both DPE and DPY is predominated by the through-bond mechanism. The remarkable difference of the conjugated length dependence of squared CT coupling between substituted DPE and DPY is the result of the energetic matching degree of the frontier molecular orbitals between donor/acceptor and the conjugated bridge.     

7.

An analysis of the vibrational frequencies and amplitudes of the H5O+2 ion in H4SiW12O40·6H2O (TSA·6H2O) and H3PW12O40·6H2O (TPA·6H2O)     

《Spectrochimica Acta Part A: Molecular and Biomolecular Spectroscopy》1990,46(3):419-424

The infrared, Raman and inelastic neutron scattering (INS) spectra of TSA·6H₂O and TPA·6H₂O are in agreement with those expected for the presence of H₅O⁺₂ ions. Force fields for different assignment schemes are compared with the observed vibrational frequencies and the INS spectral profile. All but two schemes are eliminated. Whilst low-resolution INS spectroscopy cannot distinguish between these two schemes, the orientations of the vibrational ellipsoids for one scheme are in better agreement with those reported from low-temperature crystallographic studies of the H₅O⁺₂ ion.     

8.

Hexaaquacobalt(II) and hexaaquacadmium(II) 4-nitro-2,3,5,6-tetraoxopyridinates [M(H2O)6](C5HN2O6)2 · 2H2O (M = Co and Cd): Synthesis, structures, and properties     

O. V. Kovalchukova  A. I. Stash  Dinh Do Nguyen  S. B. Strashnova  V. K. Bel’skii 《Russian Journal of Coordination Chemistry》2013,39(3):234-238

The complexes [Cd(H₂O)₆](C₅HN₂O₆)₂ · 2H₂O (I) and [Co(H₂O)₆](C₅HN₂O₆)₂ · 2H₂O (II) were obtained in the crystalline state by reactions of cobalt chloride and cadmium chloride with ammonium 4-nitro-2,3,5,6-tetraoxopyridinate, (NH₄)₂ · (C₅HO₆N₂)₂. Their cocrystallization gave the heterometallic complex [Cd_0.32Co_0.68(H₂O)₆](C₅HN₂O₆)₂ · 2H₂O (III). The crystal and molecular structures of complexes I-III were determined by X-ray diffraction. It was demonstrated that the complexation reactions occur by replacement of two ammonium cations 4-nitro-2,3,5,6-tetraoxopyridinate by the complex cations [M(H₂O)₆]²⁺. The tetraoxopyridinate anions and the complex cations are hydrogen-bonded through the coordinated and crystallization water molecules as well as through the O atoms of the organic anion. The thermolysis of complexes I and II was examined by TGA.     

9.

Characterization of Mg–Y co-doped ZrO2/MgAl2O4 composite ceramic and the corrosion reaction in molten uranium     

Tong Zhang  Dingding Wang  Liping Luo  Sibo Shen  Shuxin Niu  Shu Cai 《Journal of Radioanalytical and Nuclear Chemistry》2016,310(1):239-246

     

10.

Me−H2O distances in crystal hydrates and radii of ions in aqueous solution     

S. I. Drakin 《Journal of Structural Chemistry》1963,4(4):472-478

     

11.

Combustion characteristics and kinetics of DPR Korea’s anthracite in O2/N2 and O2/CO2 atmosphere     

Yongju  O.  Zhang  Yongsheng 《Journal of Thermal Analysis and Calorimetry》2022,147(22):12897-12905

Journal of Thermal Analysis and Calorimetry - In O2/N2 and O2/CO2 atmospheres with oxygen concentrations of 21%, 30%, and 50%, combustion characteristics index, apparent activation energy, and...     

12.

Infrared photodissociation spectroscopy of H(+)(H2O)6·M(m) (M = Ne, Ar, Kr, Xe, H2, N2, and CH4): messenger-dependent balance between H3O(+) and H5O2(+) core isomers     

Mizuse K  Fujii A 《Physical chemistry chemical physics : PCCP》2011,13(15):7129-7135

Although messenger mediated spectroscopy is a widely-used technique to study gas phase ionic species, effects of messengers themselves are not necessarily clear. In this study, we report infrared photodissociation spectroscopy of H(+)(H(2)O)(6)·M(m) (M = Ne, Ar, Kr, Xe, H(2), N(2), and CH(4)) in the OH stretch region to investigate messenger(M)-dependent cluster structures of the H(+)(H(2)O)(6) moiety. The H(+)(H(2)O)(6), the protonated water hexamer, is the smallest system in which both the H(3)O(+) (Eigen) and H(5)O(2)(+) (Zundel) hydrated proton motifs coexist. All the spectra show narrower band widths reflecting reduced internal energy (lower vibrational temperature) in comparison with bare H(+)(H(2)O)(6). The Xe-, CH(4)-, and N(2)-mediated spectra show additional band features due to the relatively strong perturbation of the messenger. The observed band patterns in the Ar-, Kr-, Xe-, N(2)-, and CH(4)-mediated spectra are attributed mainly to the "Zundel" type isomer, which is more stable. On the other hand, the Ne- and H(2)-mediated spectra are accounted for by a mixture of the "Eigen" and "Zundel" types, like that of bare H(+)(H(2)O)(6). These results suggest that a messenger sometimes imposes unexpected isomer-selectivity even though it has been thought to be inert. Plausible origins of the isomer-selectivity are also discussed.     

13.

Fourier transform infrared studies of 5′-GMP in 2H2O and H2O solutions.     

《Journal of Molecular Structure》1988

In a previous work (ref. 1) we observed important changes in the 1700–1400 cm⁻¹ region of FTIR spectra in ²H₂O solutions when 5′-GMP concentration increases. These changes can be attributed to the self-association of this mononucleotide. Recently, study of this process has been extended to other regions of the spectrum and to H₂O solution. Fourier deconvolution has been employed in order to resolve the broad band into component bands. Differences have been observed between spectra in H₂O and ²H₂O for the same solute concentration. The possible causes of these differences are indicated.     

14.

The litchi (Litchi Chinensis) peels extract as a potential green inhibitor in prevention of corrosion of mild steel in 0.5 M H2SO4 solution     

M. Ramananda Singh  Prachi Gupta  Kaushal Gupta 《Arabian Journal of Chemistry》2019,12(7):1035-1041

The corrosion inhibition of mild steel in 0.5 M H₂SO₄ solution by the extract of litchi peel (Litchi chinensis) was studied by weight loss method, potentiodynamics polarization and electrochemical impedance spectroscopy (EIS). The results show that the litchi peels extract acts as mixed-type inhibitor. The inhibition of corrosion is found to be due to adsorption of the extract on metal surface, which is in conformity with Langmuir’s adsorption isotherm. UV–Vis, Fourier transform infrared (FT-IR) spectroscopy and Scanning electron microscopy (SEM) studies confirm that the inhibition of corrosion of mild steel occurs through adsorption of the inhibitor molecules.     

15.

Monte Carlo simulation and electrochemical performance corrosion inhibition whid benzimidazole derivative for XC48 steel in 0.5 M H2SO4 and 1.0 M HCl solutions     

L. Toukal  M. Foudia  D. Haffar  N. Aliouane  M. Al-Noaimi  Y. Bellal  H. Elmsellem  І. Abdеl-Rahman 《印度化学会志》2022,99(9):100634

The inhibition of 1-(4-methoxybenzyl)-2-(4-methoxyphenyl)-1H-benzimidazole (MMB) on corrosion of XC48 steel in solutions 1.0 M HCl and 0.5 M H₂SO₄ were studied by potentiodynamic polarization and electrochemical impedance spectroscopy techniques (EIS). Potentiodynmic polarization curves revealed that MMB acts as a mixed-type inhibitor in both acidic media. The impedance results indicated that the corrosion process occurs under activation control. Furthermore, MMB shows a higher inhibition efficiency in HCl (97%) than in H₂SO₄ (92%) at 10^?4 M MMB. The values of ΔG°_ads, ΔH_a, E_a and ΔS_a in temperature range 293–323 K indicated that MMB strongly retarded the corrosion of XC48 steel in both solutions by a chemisorptions process. The adsorption of Benzimidazole (MMB) on carbon steel surface followed Langmuir adsorption isotherm. Scanning electron microscopy (SEM) analysis confirmed that there is an adsorbed film on the surface of XC48 steel. The results of Monte Carlo simulations studies confirmed the inhibition action of MMB.     

16.

Gold-vanadium-niobium catalysts in environmental protection—adsorption and interaction of NO, C3H6 and O2—FT-IR study     

Izabela Sobczak  Maria Ziolek  Natalia Kieronczyk 《Adsorption》2009,15(2):145-155

FT-IR study of NO and C₃H₆ adsorption, co-adsorption and interaction in the presence of oxygen were performed in order to estimate the catalytic behaviour of Au and V-containing MCM-41 materials in NO-SCR with propene. MCM-41 were modified with gold, vanadium and niobium by their introduction during the synthesis (co-precipitation) carried out with the use of HCl or H₂SO₄ as pH adjustment agent. The texture/structure properties of the prepared samples were investigated by N₂ adsorption, XRD, XPS and TEM techniques. It has been found that the nature of acid used for the pH adjustment during the synthesis determines the gold particles size and dispersion and influences the interaction of NO+O₂+C₃H₆ with the catalyst surfaces. In both types of AuVMCM-41 catalysts, the SCR reaction route occurs via NO₂ formation. In the case of AuVMCM-41(HCl) and AuVNbMCM-41(HCl) nitrites are formed and stored, and upon heating NO₂ is released. These kinds of nitrites are not formed on AuVMCM-41(H₂SO₄) and AuVNbMCM-41(H₂SO₄). Instead of that NO₂ is chemisorbed on metallic gold, niobium and vanadium species and reacts with propene and/or oxygenates.     

17.

The enthalpy of solution of MgCl2 and MgCl2·6H2O in water at 25°C. I. The integral molar enthalpy of solution     

H. Jahn  G. Wolf 《Journal of solution chemistry》1993,22(11):983-994

The data for the relative apparent and integral molar enthalpy of solution, L and H _sol ⁱⁿ , respectively, were critically reviewed, for the magnesium chloride-water system at 25°C. The concentration dependence L(m) and the enthalpy of solution at infinite dilution H _sol ^o were determined calorimetrically at 25°C. Both results are in agreement with most of the small amount of data published previously. From the results of our measurements, and from the most reliable value for H _sol ^o of MgCl₂, the concentration dependence H _sol ⁱⁿ (m) at 25°C was derived, for MgCl₂·6H₂O. The enthalpy of the hydration

Electrocatalytic activity and stability of Ti/IrO2 + MnO2 anode in 0.5 M NaCl solution

Ti/IrO₂(x) + MnO₂(1-x) anodes have been fabricated by thermal decomposition of a mixed H₂IrCl₆ and Mn(NO₃)₂ hydrosolvent. Cyclic voltammetry (CV) and polarization curve have been utilized to investigate the electrochemical behavior and electrocatalytic activity of Ti/IrO₂(x) + MnO₂(1-x) anodes in 0.5 M NaCl solution (pH = 2). Ti/IrO₂+MnO₂ anode with 70 mol% IrO₂ content has the maximum value of q*, indicating that Ti/IrO₂(0.7) + MnO₂(0.3) anode has the most excellent electrocatalytic activity for the synchronal evolution of Cl₂ and O₂ in dilute NaCl solution. Tafel lines displayed two distinct linear regions with one of the slope close to 62 mV dec⁻¹ in the low potential region and the other close to 295 mV dec⁻¹ in the high potential region. Electrochemical impedance spectroscopic is employed to investigate the impedance behavior of Ti/IrO₂(x) + MnO₂(1-x) anodes in 0.5 M NaCl solution. It is observed that as the R _ct, R _s and R _f values for Ti/IrO₂(0.7) + MnO₂(0.3) anode become smaller, electrocatalytic activity of Ti/IrO₂(0.7) + MnO₂(0.3) anode becomes better than that of other Ti/IrO₂ + MnO₂ anodes with different compositions. Ti/IrO₂(0.7) + MnO₂(0.3) anode fabricated at 400 °C has been observed to possess the highest service life of 225 h, whereas the accelerated life test is carried out under the anodic current of 2 A cm⁻² at the temperature of 50 °C in 0.5 M NaCl solution (pH = 2).     

One-Pot Reduction of Sulfoxides with NaBH4, CoCl2 · 6H2O Catalyst,and Moist Alumina

Sulfoxides are reduced by a combination of sodium borohydride, a catalytic amount of cobalt(II) chloride hexahydrate, and chromatographic neutral alumina preloaded with a small amount of water (moist alumina) in hexane to produce the corresponding sulfides in good to excellent yields under mild conditions. An interesting structural influence of sulfoxides on their reactivity is observed.

Spectral and intramolecular charge transfer properties in terminal donor/acceptor-substituted all-trans-α,ω-diphenylpolyenes and α,ω-diphenylpolyynes

The absorption spectra and intramolecular charge transfer (CT) properties of terminal donor/acceptor-substituted all-trans-α,ω-diphenylpolyenes (DPE) and α,ω-diphenylpolyynes (DPY) molecules with different conjugated bridge length and substitution modes were investigated by using quantum chemical calculations. We calculated the ground state structures and energy of two series of terminal donor/acceptor DPE and DPY by DFT method. The dependence of conjugation length and substitution modes of the electronic absorption spectra was obtained by TDDFT calculation. The hybrid-GGA XC-functional PBE0 employed in this work was selected from several functionals by comparing the calculated electronic spectral data with experimental value. The CIS-based generalized Mulliken-Hush (GMH) approach was further used to calculate coupling values H(AD) of the CT process. The calculation shows that both the HOMO-LUMO energy gaps and average bond length alternations between unsaturated multiple (C≡C and C=C) and saturated single bonds (C-C) decrease regularly with the extension of conjugation. The effective conjugated length (ECL) of DPE and DPY with the same order MM > MP/PM > PP is found together with the regular red shift of the electronic absorption spectra with the extension of conjugation, resulting from the different π-electron delocalization and conjugation efficiency. The GMH analysis further suggests that the CT process in both DPE and DPY is predominated by the through-bond mechanism. The remarkable difference of the conjugated length dependence of squared CT coupling between substituted DPE and DPY is the result of the energetic matching degree of the frontier molecular orbitals between donor/acceptor and the conjugated bridge.     

An analysis of the vibrational frequencies and amplitudes of the H5O+2 ion in H4SiW12O40·6H2O (TSA·6H2O) and H3PW12O40·6H2O (TPA·6H2O)

The infrared, Raman and inelastic neutron scattering (INS) spectra of TSA·6H₂O and TPA·6H₂O are in agreement with those expected for the presence of H₅O⁺₂ ions. Force fields for different assignment schemes are compared with the observed vibrational frequencies and the INS spectral profile. All but two schemes are eliminated. Whilst low-resolution INS spectroscopy cannot distinguish between these two schemes, the orientations of the vibrational ellipsoids for one scheme are in better agreement with those reported from low-temperature crystallographic studies of the H₅O⁺₂ ion.     

Hexaaquacobalt(II) and hexaaquacadmium(II) 4-nitro-2,3,5,6-tetraoxopyridinates [M(H2O)6](C5HN2O6)2 · 2H2O (M = Co and Cd): Synthesis, structures, and properties

The complexes [Cd(H₂O)₆](C₅HN₂O₆)₂ · 2H₂O (I) and [Co(H₂O)₆](C₅HN₂O₆)₂ · 2H₂O (II) were obtained in the crystalline state by reactions of cobalt chloride and cadmium chloride with ammonium 4-nitro-2,3,5,6-tetraoxopyridinate, (NH₄)₂ · (C₅HO₆N₂)₂. Their cocrystallization gave the heterometallic complex [Cd_0.32Co_0.68(H₂O)₆](C₅HN₂O₆)₂ · 2H₂O (III). The crystal and molecular structures of complexes I-III were determined by X-ray diffraction. It was demonstrated that the complexation reactions occur by replacement of two ammonium cations 4-nitro-2,3,5,6-tetraoxopyridinate by the complex cations [M(H₂O)₆]²⁺. The tetraoxopyridinate anions and the complex cations are hydrogen-bonded through the coordinated and crystallization water molecules as well as through the O atoms of the organic anion. The thermolysis of complexes I and II was examined by TGA.     

Combustion characteristics and kinetics of DPR Korea’s anthracite in O2/N2 and O2/CO2 atmosphere

Journal of Thermal Analysis and Calorimetry - In O2/N2 and O2/CO2 atmospheres with oxygen concentrations of 21%, 30%, and 50%, combustion characteristics index, apparent activation energy, and...     

Infrared photodissociation spectroscopy of H(+)(H2O)6·M(m) (M = Ne, Ar, Kr, Xe, H2, N2, and CH4): messenger-dependent balance between H3O(+) and H5O2(+) core isomers

Although messenger mediated spectroscopy is a widely-used technique to study gas phase ionic species, effects of messengers themselves are not necessarily clear. In this study, we report infrared photodissociation spectroscopy of H(+)(H(2)O)(6)·M(m) (M = Ne, Ar, Kr, Xe, H(2), N(2), and CH(4)) in the OH stretch region to investigate messenger(M)-dependent cluster structures of the H(+)(H(2)O)(6) moiety. The H(+)(H(2)O)(6), the protonated water hexamer, is the smallest system in which both the H(3)O(+) (Eigen) and H(5)O(2)(+) (Zundel) hydrated proton motifs coexist. All the spectra show narrower band widths reflecting reduced internal energy (lower vibrational temperature) in comparison with bare H(+)(H(2)O)(6). The Xe-, CH(4)-, and N(2)-mediated spectra show additional band features due to the relatively strong perturbation of the messenger. The observed band patterns in the Ar-, Kr-, Xe-, N(2)-, and CH(4)-mediated spectra are attributed mainly to the "Zundel" type isomer, which is more stable. On the other hand, the Ne- and H(2)-mediated spectra are accounted for by a mixture of the "Eigen" and "Zundel" types, like that of bare H(+)(H(2)O)(6). These results suggest that a messenger sometimes imposes unexpected isomer-selectivity even though it has been thought to be inert. Plausible origins of the isomer-selectivity are also discussed.     

Fourier transform infrared studies of 5′-GMP in 2H2O and H2O solutions.

In a previous work (ref. 1) we observed important changes in the 1700–1400 cm⁻¹ region of FTIR spectra in ²H₂O solutions when 5′-GMP concentration increases. These changes can be attributed to the self-association of this mononucleotide. Recently, study of this process has been extended to other regions of the spectrum and to H₂O solution. Fourier deconvolution has been employed in order to resolve the broad band into component bands. Differences have been observed between spectra in H₂O and ²H₂O for the same solute concentration. The possible causes of these differences are indicated.     

The litchi (Litchi Chinensis) peels extract as a potential green inhibitor in prevention of corrosion of mild steel in 0.5 M H2SO4 solution

The corrosion inhibition of mild steel in 0.5 M H₂SO₄ solution by the extract of litchi peel (Litchi chinensis) was studied by weight loss method, potentiodynamics polarization and electrochemical impedance spectroscopy (EIS). The results show that the litchi peels extract acts as mixed-type inhibitor. The inhibition of corrosion is found to be due to adsorption of the extract on metal surface, which is in conformity with Langmuir’s adsorption isotherm. UV–Vis, Fourier transform infrared (FT-IR) spectroscopy and Scanning electron microscopy (SEM) studies confirm that the inhibition of corrosion of mild steel occurs through adsorption of the inhibitor molecules.     

Monte Carlo simulation and electrochemical performance corrosion inhibition whid benzimidazole derivative for XC48 steel in 0.5 M H2SO4 and 1.0 M HCl solutions

The inhibition of 1-(4-methoxybenzyl)-2-(4-methoxyphenyl)-1H-benzimidazole (MMB) on corrosion of XC48 steel in solutions 1.0 M HCl and 0.5 M H₂SO₄ were studied by potentiodynamic polarization and electrochemical impedance spectroscopy techniques (EIS). Potentiodynmic polarization curves revealed that MMB acts as a mixed-type inhibitor in both acidic media. The impedance results indicated that the corrosion process occurs under activation control. Furthermore, MMB shows a higher inhibition efficiency in HCl (97%) than in H₂SO₄ (92%) at 10^?4 M MMB. The values of ΔG°_ads, ΔH_a, E_a and ΔS_a in temperature range 293–323 K indicated that MMB strongly retarded the corrosion of XC48 steel in both solutions by a chemisorptions process. The adsorption of Benzimidazole (MMB) on carbon steel surface followed Langmuir adsorption isotherm. Scanning electron microscopy (SEM) analysis confirmed that there is an adsorbed film on the surface of XC48 steel. The results of Monte Carlo simulations studies confirmed the inhibition action of MMB.     

Gold-vanadium-niobium catalysts in environmental protection—adsorption and interaction of NO, C3H6 and O2—FT-IR study

FT-IR study of NO and C₃H₆ adsorption, co-adsorption and interaction in the presence of oxygen were performed in order to estimate the catalytic behaviour of Au and V-containing MCM-41 materials in NO-SCR with propene. MCM-41 were modified with gold, vanadium and niobium by their introduction during the synthesis (co-precipitation) carried out with the use of HCl or H₂SO₄ as pH adjustment agent. The texture/structure properties of the prepared samples were investigated by N₂ adsorption, XRD, XPS and TEM techniques. It has been found that the nature of acid used for the pH adjustment during the synthesis determines the gold particles size and dispersion and influences the interaction of NO+O₂+C₃H₆ with the catalyst surfaces. In both types of AuVMCM-41 catalysts, the SCR reaction route occurs via NO₂ formation. In the case of AuVMCM-41(HCl) and AuVNbMCM-41(HCl) nitrites are formed and stored, and upon heating NO₂ is released. These kinds of nitrites are not formed on AuVMCM-41(H₂SO₄) and AuVNbMCM-41(H₂SO₄). Instead of that NO₂ is chemisorbed on metallic gold, niobium and vanadium species and reacts with propene and/or oxygenates.     

The enthalpy of solution of MgCl2 and MgCl2·6H2O in water at 25°C. I. The integral molar enthalpy of solution

The data for the relative apparent and integral molar enthalpy of solution, L and H _sol ⁱⁿ , respectively, were critically reviewed, for the magnesium chloride-water system at 25°C. The concentration dependence L(m) and the enthalpy of solution at infinite dilution H _sol ^o were determined calorimetrically at 25°C. Both results are in agreement with most of the small amount of data published previously. From the results of our measurements, and from the most reliable value for H _sol ^o of MgCl₂, the concentration dependence H _sol ⁱⁿ (m) at 25°C was derived, for MgCl₂·6H₂O. The enthalpy of the hydration

Crystal structure and properties of H3[PMo12O40] · 3C2H6O

The title compound H₃[PMo₁₂O₄₀]· 3C₂H₆O was prepared and characterized by X-ray crystallography, its i.r. spectrum, cyclic voltammetry and e.s.r. spectra. The anion of the title compound is a Keggin-type heteropoly structure based upon a central PO₄ tetrahedron surrounded by 12 MoO₆ octahedra arranged in four groups of three edge-shared octahedra Mo₃O₁₃. Weak hydrogen bonds exist between the organic solvent molecules and the heteropoly anion. The catalytic activity of the title compound was determined by the synthesis of butyl acetate. The conversion of n-BuOH reached 93.3% and the yield of MeCO₂Bu-n was 92.0% when the ratio of MeCO₂H to n-BuOH, catalyst amount, reaction time, reaction temperature were 2:1, 0.24% of the reactants (50 mg), 2.0 h and 115 120 °C, respectively.     

Electronic properties and charge transfer phenomena in Pt nanoparticles on γ-Al(2)O(3): size, shape, support, and adsorbate effects

This study presents a systematic detailed experimental and theoretical investigation of the electronic properties of size-controlled free and γ-Al(2)O(3)-supported Pt nanoparticles (NPs) and their evolution with decreasing NP size and adsorbate (H(2)) coverage. A combination of in situ X-ray absorption near-edge structure (XANES) and density functional theory (DFT) calculations revealed changes in the electronic characteristics of the NPs due to size, shape, NP-adsorbate (H(2)) and NP-support interactions. A correlation between the NP size, number of surface atoms and coordination of such atoms, and the maximum hydrogen coverage stabilized at a given temperature is established, with H/Pt ratios exceeding the 1?:?1 ratio previously reported for bulk Pt surfaces.     

AlCl3 · 6H2O/KI/CH3CN/H2O: An Efficient and Versatile System for Chemoselective C–O Bond Cleavage and Formation of Halides and Carbonyl Compounds from Alcohols in Hydrated Media

AlCl₃ · 6H₂O/KI/CH₃CN/H₂O, an efficient and versatile system, cleaves the C–O bonds of esters, acetals, ethers, and oxathiolanes to the corresponding acids, alcohols, and carbonyl compounds chemoselectively at 80 °C in hydrated media with good yields. This system also converts the alcohols (primary/secondary) to halides and oxidizes the alcohols (primary/secondary) to the corresponding carbonyl compounds in the presence of DMSO.