Effect of solvents on the morphology of NiCo<Subscript>2</Subscript>O<Subscript>4</Subscript>/graphene nanostructures for electrochemical pseudocapacitor application

The large internal surface areas and outstanding electrical and mechanical properties of graphene have prompted to blend graphene with NiCo₂O₄ to fabricate nanostructured NiCo₂O₄/graphene composites for supercapacitor applications. The use of graphene as blending with NiCo₂O₄ enhances the specific capacitance and rate capability and improves the cyclic performance when compared to the pristine NiCo₂O₄ material. Here, we synthesized two different nanostructured morphologies of NiCo₂O₄ on graphene sheets by solvothermal method. It has been suggested that the morphologies of oxides are greatly influenced by dielectric constant, thermal conductivity, and viscosity of solvents employed during the synthesis. In order to test this concept, we have synthesized nanostructured NiCo₂O₄ on graphene sheets by facile solvothermal method using N-methyl pyrrolidone and N,N-dimethylformamide solvents with water. We find that mixture of N-methyl pyrrolidone and water solvent favored the formation of nanonet-like NiCo₂O₄/graphene (NiCoO-net) whereas mixture of N,N-dimethylformamide and water solvent produced microsphere-like NiCo₂O₄/graphene (NiCoO-sphere). Electrochemical pseudocapacitance behavior of the two NiCo₂O₄/graphene electrode materials was studied by cyclic voltammetry, chronopotentiometry, and electrochemical impedance spectroscopy techniques. The supercapacitance measurements on NiCoO-net and NiCoO-sphere electrodes showed specific capacitance values of 1060 and 855 F g^?1, respectively, at the current density of 1.5 A g^?1. The capacitance retention of NiCoO-net electrode is 93 % while that of NiCoO-sphere electrode is 77 % after long-term 5000 charge-discharge cycles at high current density of 10 A g^?1.     

Hydrogen peroxide sensor based on a stainless steel electrode coated with multi-walled carbon nanotubes modified with magnetite nanoparticles

Multi-walled carbon nanotubes (MWCNTs) were decorated with magnetite (Fe₃O₄) nanoparticles and then used to modify a stainless steel electrode. The Fe₃O₄/MWCNTs composite was characterized by scanning electron microscopy, transmission electron microscopy, Raman spectroscopy and X-ray diffraction patterns. Electrochemical properties of the modified electrode revealed a substantial catalytic activity for the reduction of hydrogen peroxide. The relationship between peak current and the concentration of hydrogen peroxide was linear in the range from 0.06?mmol?L^?1 to 0.36?mmol?L^?1, and the lowest detectable concentration is 0.01?mmol·L^?1 (S/N?=?3). The modified stainless steel electrode displays excellent stability.

A high mass loading electrode based on ultrathin Co<Subscript>3</Subscript>S<Subscript>4</Subscript> nanosheets for high performance supercapacitor

There is a growing need for the electrode with high mass loading of active materials, where both high energy and high power densities are required, in current and near-future applications of supercapacitor. Here, an ultrathin Co₃S₄ nanosheet decorated electrode (denoted as Co₃S₄/NF) with mass loading of 6 mg cm^?2 is successfully fabricated by using highly dispersive Co₃O₄ nanowires on Ni foam (NF) as template. The nanosheets contained lots of about 3～5 nm micropores benefiting for the electrochemical reaction and assembled into a three-dimensional, honeycomb-like network with 0.5～1 μm mesopore structure for promoting specific surface area of electrode. The improved electrochemical performance was achieved, including an excellent cycliability of 10,000 cycles at 10 A g^?1 and large specific capacitances of 2415 and 1152 F g^?1 at 1 and 20 A g^?1, respectively. Impressively, the asymmetric supercapacitor assembled with the activated carbon (AC) and Co₃S₄/NF electrode exhibits a high energy density of 79 Wh kg^?1 at a power density of 151 W kg^?1, a high power density of 3000 W kg^?1 at energy density of 30 Wh kg^?1 and 73 % retention of the initial capacitance after 10,000 charge-discharge cycles at 2 A g^?1. More importantly, the formation process of the ultrathin Co₃S₄ nanosheets upon reaction time is investigated, which is benefited from the gradual infiltration of sulfide ions and the template function of ultrafine Co₃O₄ nanowires in the anion-exchange reaction.

Open image in new window

Graphical abstract The ultrathin 2D Co₃S₄ nanosheets fabricated on 3D Ni foam and the formation process of the ultrathin Co₃S₄ nanosheets upon reaction times has been investigated. At the same time, the Co₃S₄/NF electrode displays an outstanding specific capacitance of 2420 F g^?1 at 1 A g^?1 with high mass loading of 6 mg cm^?2.

     

The preparation of LaSr<Subscript>3</Subscript>Fe<Subscript>3</Subscript>O<Subscript>10 − <Emphasis Type="Italic">δ</Emphasis></Subscript> and its electrochemical performance

LaSr₃Fe₃O_10 ? δ powders were synthesized by hydrothermal method and characterized by XRD and SEM. The XRD patterns showed that the sample calcined at 1000 °C was single phase and the sample calcined at 900 °C had tiny amount of LaSrFeO₄ phase. The single-phase LaSr₃Fe₃O_10 ? δ powders were used to prepare test electrode. The capacitive behaviors of LaSr₃Fe₃O_10 ? δ electrode were analyzed by cyclic voltammetry, galvanostatic charge-discharge techniques, and electrochemical impedance spectroscopy. The electrochemical results showed a capacity as high as 470 F g^?1 at a scan rate of 1 mV s^?1 and 380 F g^?1 at a charge-discharge current density of 0.1 A g^?1 in 6 M KOH solution. The electrode showed good cyclic stability since its capacitive retention is 87.1% after 1000 charge-discharge cycles. The electrochemical performances suggest that LaSr₃Fe₃O_10 ? δ could be a potential candidate as a capacitive electrode material.     

Self-assembly of ultra-small gold nanoparticles on an indium tin oxide electrode for the enzyme-free detection of hydrogen peroxide

A novel enzyme-free electrochemical sensor for H₂O₂ was fabricated by modifying an indium tin oxide (ITO) support with (3-aminopropyl) trimethoxysilane to yield an interface for the assembly of colloidal gold. Gold nanoparticles (AuNPs) were then immobilized on the substrate via self-assembly. Atomic force microscopy showed the presence of a monolayer of well-dispersed AuNPs with an average size of ~4 nm. The electrochemical behavior of the resultant AuNP/ITO-modified electrode and its response to hydrogen peroxide were studied by cyclic voltammetry. This non-enzymatic and mediator-free electrode exhibits a linear response in the range from 3.0?×?10^?5 M to 1.0?×?10^?3 M (M?=?mol?·?L^?1) with a correlation coefficient of 0.999. The limit of detection is as low as 10 nM (for S/N?=?3). The sensor is stable, gives well reproducible results, and is deemed to represent a promising tool for electrochemical sensing.

Preparation,characterization, and evaluation of LiNi0.4Co0.6O2 nanofibers for supercapacitor applications

We prepared LiNi_0.4Co_0.6O₂ nanofibers by electrospinning at the calcination temperature of 450 °C for 6 h. The prepared LiNi_0.4Co_0.6O₂ nanofibers was characterized by thermal, X-ray diffraction, and Fourier transform infrared (FTIR) studies. The morphology of LiNi_0.4Co_0.6O₂ nanofibers was characterized by scanning electron microscopy studies. The asymmetric supercapacitor was fabricated using LiNi_0.4Co_0.6O₂ nanofibers as positive electrode and activated carbon (AC) as negative electrode and a porous polypropylene separator in 1 M LiPF₆–ethylene carbonate/dimethyl carbonate (LiPF₆–EC:DMC) (1:1?v/v) as electrolyte. Cyclic voltammetry studies were then carried out in the potential range of 0 to 3.0 V at different scan rates which exhibited the highest specific capacitance of 72.9 F g^?1. The electrochemical impedance measurements were carried out to find the charge transfer resistance and specific capacitance of the cell, and they were found to be 5.05 Ω and 67.4 F g^?1, respectively. Finally, the charge–discharge studies were carried out at a current density of 1 mA cm^?2 to find out the discharge-specific capacitance, energy density, and power density of the capacitor cell, and they were found to be 70.9 F g^?1, 180.2 Wh kg^?1, and 248.0 W kg^?1, respectively.     

Effect of carbonaceous support between graphite oxide and reduced graphene oxide with anchored Co<Subscript>3</Subscript>O<Subscript>4</Subscript> microspheres as electrode-active materials in a solid-state electrochemical capacitor

Hydrothermally synthesized Co₃O₄ microspheres were anchored to graphite oxide (GO) and thermally reduced graphene oxide (rGO) composites at different cobalt weight percentages (1, 10, and 100 wt%). The composite materials served as the active materials in bulk electrodes for two-electrode cell electrochemical capacitors (ECCs). GO/Co₃O₄–1 exhibited a high energy density of 35 W kg^?1 with a specific capacitance (C _sp) of 196 F g^?1 at a maximum charge density of 1 A g^?1. rGO/Co₃O₄-100 presented high specific power output values of up to 23.41 kW h kg^?1 with linear energy density behavior for the charge densities applied between 0.03 and 1 A g^?1. The composite materials showed Coulombic efficiencies of 96 and 93 % for GO/Co₃O₄–1 and rGO/Co₃O₄–100 respectively. The enhancement of capacitive performance is attributed to the oxygenated groups in the GO ECC and the specific area in the rGO ECC. These results offer an interesting insight into the type of carbonaceous support used for graphene derivative electrode materials in ECCs together with Co₃O₄ loading to improve capacitance performance in terms of specific energy density and specific power.

Open image in new window

Graphical abstract ?

     

Hierarchical nanocomposites of polyaniline scales coated on graphene oxide sheets for enhanced supercapacitors

The homogeneous polyaniline–graphene oxide (PANI-GO) nanocomposites were facilely assembled with a redox system in which cumene hydroperoxide (CHP) and iron dichloride (FeCl₂) acted as oxidant and reductant, respectively. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) images showed that PANI scales coated uniformly on the surface of GO sheets owing to the synergistic effect between the PANI and GO. The obtained PANI-GO nanocomposites exhibited improved electrochemical performance as an electrode material for supercapacitors compared with the pure PANI. The specific capacitance of the PANI-GO nanocomposites was high up to 308.3 F g^?1, much higher than that of the pure PANI with specific capacitance of 150 F g^?1 at a current density of 1 A g^?1 in 2 M H₂SO₄ electrolyte. The Raman and XPS results illustrated that enhanced electrochemical performance might be attributed to the π-π conjugation between the PANI and GO sheets.     

Iodide-induced adsorption of lead(II) ion on a glassy carbon electrode modified with ferroferric oxide nanoparticles

Spherical Fe₃O₄ nanoparticles (NPs) were prepared by hydrothermal synthesis and characterized by scanning electron microscopy and X-ray diffraction. A glassy carbon electrode was modified with such NPs to result in a sensor for Pb(II) that is based on the strong inducing adsorption ability of iodide. The electrode gives a pair of well-defined redox peaks for Pb(II) in pH 5.0 buffer containing 10 mM concentrations of potassium iodide, with anodic and cathodic peak potentials at ?487 mV and ?622 mV (vs. Ag/AgCl), respectively. The amperometric response to Pb(II) is linear in the range from 0.10 to 44 nM, and the detection limit is 40 pM at an SNR of 3. The sensor exhibits high selectivity and reproducibility.

Fabrication and characterisation of a mixed oxide-covered mesh electrode composed of NiCo<Subscript>2</Subscript>O<Subscript>4</Subscript> and its capability of generating hydroxyl radicals during the oxygen evolution reaction in electrolyte-free water

A mixed oxide-covered mesh electrode composed of NiCo₂O₄ (MOME-NiCo₂O₄) was prepared on a stainless-steel substrate using thermal decomposition (slow-cooling rate method). Surface, bulk and electrochemical properties of MOME were studied using different techniques, namely scanning electron microscopy (SEM), X-ray diffraction (XRD), cyclic voltammetry (CV) with determination of the electrochemical porosity (?) and morphology factor (φ) parameters, quasi-stationary polarisation curves (PC) and electrochemical impedance spectroscopy (EIS). SEM images revealed a good coverage of the metallic wires by a compact oxide layer (absence of cracks). XRD analysis confirmed the formation of the spinel NiCo₂O₄ with the presence of NiO. The ‘in situ’ surface parameters denoted as ? and φ exhibited values of 0.39 and 0.33, respectively, revealing that the electrochemically active surface area is mainly confined to the ‘outer/external’ surface regions of the oxide layer. The PC was characterised by two Tafel slopes distributed in the low (b ₁ = 46 mV dec^?1) and high (b ₂ = 59 mV dec^?1) overpotential domains. The corresponding apparent exchange current densities were j ₀₍₁₎ = (3.43 ± 0.11) × 10^?6 A cm^?2 and j ₀₍₂₎ = (6.70 ± 0.08) × 10^?6 A cm^?2, respectively. The EIS study accomplished in the low-overpotential domain revealed a Tafel slope (b ₁) of 51 mV dec^?1. According to the spin-trapping reaction using N,N-dimethyl-p-nitrosoaniline (RNO), the MOME-NiCo₂O₄ electrode exhibited good performance for the generation of weakly adsorbed hydroxyl radicals (HO^?) during the OER in electrolyte-free water.     

Nonenzymatic hydrogen peroxide sensor based on a glassy carbon electrode modified with electrospun PdO-NiO composite nanofibers

A glassy carbon electrode was modified with PdO-NiO composite nanofibers (PdO-NiO-NFs) and applied to the electrocatalytic reduction of hydrogen peroxide (H₂O₂). The PdO-NiO-NFs were synthesized by electrospinning and subsequent thermal treatment, and then characterized by scanning electron microscopy, energy dispersive X-ray spectroscopy, X-ray diffraction, and X-ray photoelectron spectroscopy. Factors such as the composition and fraction of nanofibers, and of the applied potential were also studied. The sensor exhibits high sensitivity for H₂O₂ (583.43 μA?·?mM^?1?·?cm^?2), a wide linear range (from 5.0 μM to 19 mM), a low detection limit (2.94 μM at an SNR of 3), good long term stability, and is resistant to fouling.

Titanium dioxide nanorod-based amperometric sensor for highly sensitive enzymatic detection of hydrogen peroxide

Titanium dioxide nanorods (TNR) were grown on a titanium electrode by a hydrothermal route and further employed as a supporting matrix for the immobilization of nafion-coated horseradish peroxidase (HRP). The strong electrostatic interaction between HRP and TNR favors the adsorption of HRP and facilitates direct electron transfer on the electrode. The electrocatalytic activity towards hydrogen peroxide (H₂O₂) was investigated via cyclic voltammetry and amperometry. The biosensor exhibits fast response, a high sensitivity (416.9 μA·mM^?1), a wide linear response range (2.5 nM to 0.46 mM), a detection limit as low as 12 nM, and a small apparent Michaelis-Menten constant (33.6 μM). The results indicate that this method is a promising technique for enzyme immobilization and for the fabrication of electrochemical biosensors.

Voltammetric and amperometric determination of hydrogen peroxide using a carbon-ceramic electrode modified with a nanohybrid composite made from single-walled carbon nanotubes and silver nanoparticles

A nanohybrid composite material was prepared from single-walled carbon nanotubes and silver nanoparticles, and used to fabricate a modified carbon-ceramic electrode. The preparation of the composite is facile and efficient. The nanohybrid composite deposited on the carbon-ceramic electrode was characterized by X-ray diffraction and cyclic voltammetry. The new electrode displays favorable electrocatalytic ability towards hydrogen peroxide (H₂O₂) and can be used to electrocatalytically reduce this species. Under the optimum conditions, the current measured during hydrodynamic amperometry is linearly related to the concentration of H₂O₂ over the concentration range from 0.01 to 8 mM, with a detection limit of 2?×?10^?7 M at a signal-to-noise ratio of 3 and sensitivity of 3.23 μA/mM. The electrode exhibits good reproducibility, long-term stability and negligible interference by dopamine, uric acid, and other important biological compounds. The electrode was successfully applied to the determination of H₂O₂ in honey samples, and the recovery was 101.2%.

One-step preparation of sulfonated carbon and subsequent preparation of hybrid material with polyaniline salt: a promising supercapacitor electrode material

The present trend to increase the energy density of electrochemical supercapacitor is to hybrid the electrochemical double layer capacitance electrode materials of carbon with loading or encapsulation of transition metal oxide or conductive polymeric pseudocapacitor materials as the binary or ternary hybrid electrochemical active materials. In this work, we selected polyaniline salt-sulfonated carbon hybrid (PANI-SA?C _SA ) as a cheaper electrode material for supercapacitor electrode. Sulfonated carbon (C _SA ) was prepared from hydrothermal carbonization of furaldehyde and p-toluenesulfonic acid. Polyaniline-sulfate salt containing sulfonated carbon was prepared by chemical oxidative polymerization of aniline using ammonium persulfate in presence of sulfuric acid and sulfonated carbon via aqueous, emulsion and interfacial polymerization pathways. Formation of hybrid material was confirmed from scanning electron microscopy. Among the hybrid prepared with three different polymerization pathways, hybrid prepared by aqueous polymerization pathway showed better electrochemical performance. The specific capacitance of the hybrid prepared via aqueous polymerization was 600 F g^?1, which is higher than that of the pristine PANI-SA (350 F g^?1) and C _SA (30 F g^?1). Hybrid material was subjected for 8000 charge-discharge cycles and at 8000 cycles; it showed 88% retention of its original specific capacitance value of 485 F g^?1 with coulombic efficiency (97–100%). These results showed that C _SA micro spheres prevent the degradation of PANI-SA chains during charge/discharge cycles. Specific capacitance, cycle life, low solution resistance, low charge transfer resistance and high phase angle value of PANI-SA?C _SA supercapacitor cell indicates a higher performance supercapacitor system.

Open image in new window

Graphical abstract Synthesis of hybrid of sulfonated carbon with polyaniline sulfate salt and its supercapacitor performance Ravi Bolagam, Palaniappan Srinivasan,^* Rajender Boddula

     

Synthesis of multi-branched gold nanoparticles by reduction of tetrachloroauric acid with Tris base, and their application to SERS and cellular imaging

A biosensor for hydrogen peroxide was constructed by immobilizing horseradish peroxidase on chitosan-wrapped NiFe₂O₄ nanoparticles on a glassy carbon electrode (GCE). The electron mediator carboxyferrocene was also immobilized on the surface of the GCE. UV?Cvis spectra, Fourier transform IR spectra, scanning electron microscopy, and electrochemical impedance spectra were acquired to characterize the biosensor. The experimental conditions were studied and optimized. The biosensor responds linearly to H₂O₂ in the range from 1.0?×?10^?5 to 2.0?×?10^?3?M and with a detection limit of 2.0?×?10^?6?M (at S/N?=?3).

Non-enzymatic hydrogen peroxide sensor based on a gold electrode modified with granular cuprous oxide nanowires

Granular nanowires with a diameter of about 60 nm were fabricated from cuprous oxide (Cu₂O) by an electrochemical method using anodic aluminium oxide as the template. A non-enzymatic sensor for hydrogen peroxide (H₂O₂) was then developed on the basis of a gold electrode modified with Cu₂O nanowires and Nafion. The resulting sensor enables the determination of H₂O₂ with a sensitivity of 745 μA?mM^?1?cm^?2, over a wide linear range (0.25 μM to 5.0 mM), and with a low detection limit (0.12 μM). The results demonstrate that the use of such granular nanowires provides a promising tool for the design of non-enzymatic chemical sensors.

Preconcentration of ultra-trace amounts of iron and antimony using ion pair solid phase extraction with modified multi-walled carbon nanotubes

Ion pair solid phase extraction was applied to the simultaneous preconcentration of iron and antimony. The ion pairs consisting of FeCl₄ ^? or SbCl₄ ^? anions and the benzyldimethyltetradecyl ammonium cation were formed on the surface of multi-walled carbon nanotubes, then eluted with nitric acid, and the elements finally quantified by ETAAS. The adsorption capacities of the impregnated MWCNTs are 9.2 mg g^?1 for iron and 27.5 mg g^?1 for antimony. The following analytical figures of merit were determined for iron and antimony, respectively: Enrichment factors of 210 and 230, assay precisions of ±5.3 % and ±4.8 %, linear calibration plots from 0.7 to 9.4 and 13.0 to 190 ng L^?1, and detection limits of 0.17 and 3.5 ng L^?1. The method was applied to the determination of iron and antimony in human hair, synthetic sample, and to the certified reference materials gold ore (MA-1b) and trace elements in water (SRM 1643d).

Electrochemical determination of dioxygen and hydrogen peroxide using Fe3O4@SiO2@hemin microparticles

Iron oxide microparticles were coated with 3-aminopropyltriethoxysilane and then coated with hemin via an amidation reaction. The resulting composite particles were characterized by transmission electron microscopy. FTIR spectroscopy revealed two bands (at 1,701 and 1,634 cm^?1), which were assigned to the carboxy group and the amide linkage, respectively, resulting from the linkage between hemin and the amino-modified Fe₃O₄ particles. In addition, strong Fe-O vibrations can be observed at 563 cm^?1. An electrode was modified with these microparticles and then showed a well-defined redox behavior of the immobilized hemin, with a fast heterogeneous electron transfer process (14.5 s^?1). The electrode is capable of sensing both O₂ and H₂O₂ and displays a wide linear range, high sensitivity, and fast response. The composites reported here also may serve as a support for the immobilization of proteins, which paves the way to potential applications in novel biosensors and bioelectronic devices.

Electrochemical determination of NADH using a glassy carbon electrode modified with Fe3O4 nanoparticles and poly-2,6-pyridinedicarboxylic acid, and its application to the determination of antioxidant capacity

We have prepared a glassy carbon electrode modified with poly-2,6-pyridinedicarboxylic acid and with magnetic Fe₃O₄ nanoparticles. This modification enhances the effective surface area and the electrocatalytic oxidation of nicotinamide adenine dinucleotide (NADH) in addition to providing positively charged groups for electrostatic assembly of the phosphate group of NADH. The modified electrode responds linearly to NADH in the range from 5?×?10^?8 to 2.5?×?10^?5?M and gives a lower detection limit of 1?×?10^?8?M. It displays satisfactory selectivity and reproducibility. The sensor was applied to rapid screening of plant extracts for their antioxidant properties.