静电纺丝法制备硼掺杂氧化硅纳米纤维用于低碳烷烃氧化脱氢制烯烃（英文）

乙烯和丙烯等低碳烯烃是重要的基础有机化工产品,广泛应用于化工生产的各个领域.相比于其他工艺,低碳烷烃氧化脱氢制烯烃工艺具有不受热力学平衡限制、无积炭等特点而被广泛研究.近年发现六方氮化硼(h-BN)、硼化硅(SiB_6)和磷酸硼(BPO_4)等非金属硼基催化剂能够高效催化烷烃氧化脱氢反应,并抑制产物烯烃的过度氧化,表现出高的催化活性和烯烃选择性.大量的研究表明,硼基催化剂活性起源于催化剂表面的"BO"物种(如B–O和B–OH等基团).氧化硼(B_2O_3)作为一种氧化气氛中化学性质稳定的含硼化合物,兼具丰富的"BO"位点,在反应条件下可形成多种结构以适用不同的化学环境,为制备高效的烷烃氧化脱氢催化剂提供了可能.在之前的研究中,多将B_2O_3浸渍在常规的TiO_2,SiO_2,Al_2O_3等三维多孔载体上用于氧化脱氢反应.考虑到B_2O_3结构的灵活性和易于成键特性,需开发更为有效的合成策略,以提升B_2O_3催化剂在氧化脱氢反应中的活性和稳定性.本文采用静电纺丝技术合成了直径为100～150 nm的多孔掺硼二氧化硅纳米纤维(PBSN)用于低碳烷烃氧化脱氢反应.静电纺丝法合成的催化剂中硼物种在开放的氧化硅纤维骨架上均匀分散且稳定固载.一维纳米纤维结构不仅有利于扩散,且赋予催化剂在高重时空速(WHSV)条件下优异的烷烃氧化脱氢反应活性.在乙烷氧化脱氢反应中,当乙烷的转化率达到44.3%时,乙烯的选择性和产率分别为84%和44.2μmol g_(cat)~(-1)s~(-1).而在丙烷脱氢反应中,当丙烷转化率为19.2%时,总烯烃选择性及丙烯产率分别为90%和76.6μmol g_(cat)~(-1)s~(-1).在温度为545℃,丙烷WHSV高达84.6 h~(-1)的条件下,催化剂保持长时间稳定.与其他负载型氧化硼催化剂相比,PBSN催化剂具有更高的烯烃选择性和稳定性.研究表明,在氧化硅负载B_2O_3催化剂催化丙烷氧化脱氢反应中,载体中Si–OH基团的存在可能会降低丙烯的选择性.瞬态分析和动力学实验表明,硼基催化剂催化烷烃氧化脱氢反应过程中O_2的活化受到烷烃的影响.本文不仅为高效硼基催化剂的合成提供了新思路,也为深入理解该类催化剂上烷烃氧化脱氢反应过程提供了实验支撑.     

静电纺丝法制备超细聚苯乙烯纳米纤维

采用静电纺丝方法制备了超细聚苯乙烯纤维, 通过向溶液中添加有机胺盐并降低溶液浓度将纤维的平均直径降至100 nm, 并研究了盐的添加量对纤维直径的影响.     

静电纺丝法制备纤维素纳米纤维的研究进展

纤维素纳米纤维很好的结合了纤维素的重要属性和纳米材料的各项特性,但纤维素大分子之间存在大量氢键,使得纤维素较难溶于普通溶剂,导致通过静电纺丝法直接制备纤维素纳米纤维具有一定的难度.而先采用静电纺丝法制备纤维素衍生物纳米纤维,再对纤维素衍生物纳米纤维进行水解也是制备纤维素纳米纤维的一种有效方法.本文对近年来这两种纤维素纳米纤维制备方法的研究进行了综述,并对静电纺制备纤维素纳米纤维的发展前景做出了展望.     

静电纺丝法制备MgO纳米纤维

以聚乙烯醇(PVA)作为络合剂与醋酸镁反应制得前驱体，采用静电纺丝法制得聚乙烯醇(PVA)／醋酸镁复合纤维，经焙烧后得到分布均匀、具有较高比表面积和多孔结构的。MgO纳米纤维．对所制得的纳米纤维的结晶度、纯度和表面形貌，分别采用X射线粉末衍射、差热一热重分析(TG-DTA)、红外光谱(IR)、扫描电镜(SEM)等分析测试手段进行了表征．结果表明，煅烧温度对纳米纤维的结晶度和形貌有很大影响．     

静电纺丝法制备纳米抗菌纤维的研究进展

纳米抗菌材料是防止细菌等致病微生物对人们生产、生活的破坏而发展起来的一类新型材料.在纳米抗菌材料的众多制备方法中,静电纺丝是一种成本低,工艺可控的技术,制备的纳米纤维具有比表面积大、孔隙率高、纤维均匀等特点.本文作者首先简述了静电纺丝技术以及该技术制备纳米抗菌纤维材料的特点;接着按照菌剂种类不同,对静电纺丝技术制备的抗菌纤维材料进行归类,将其分为无机抗菌纤维材料、天然抗菌纤维材料和复合抗菌纤维材料3类,并对其研究进展进行了评述;最后对静电纺丝技术制备纳米抗菌纤维的研究现状进行了总结与展望.     

静电纺丝法制备抑菌性聚酰亚胺纳米纤维

采用静电纺丝技术,以联苯四甲酸二酐(BPDA)和4,4'-二氨基二苯醚(ODA)为单体,硝酸银为银源,通过两步法制备含银聚酰亚胺(PI/Ag)纳米纤维.通过X射线衍射(XRD)、透射电子显微镜(TEM)及扫描电子显微镜(SEM)表征了PI/Ag纳米纤维的结构和微观形貌;通过浸渍培养法研究了聚酰亚胺(PI)及PI/Ag纳米纤维的抑菌性能.结果表明,聚酰亚胺基体中存在单质银的立方晶体结构,银粒子在聚酰亚胺基体表面均匀分散,平均粒径为10 nm;PI/Ag纳米纤维对大肠杆菌(E.coli)、金黄色葡萄球菌(S.aureus)和枯草芽孢杆菌(B.subtilis)表现出良好的抑菌效果,最大抑菌率可达99.1%,为聚酰亚胺在耐高温抑菌生物医用材料等领域的应用提供了新的方向.     

静电纺丝法制备NiO纳米纤维及其表征

纳米级NiO因具有优良的催化和热敏等性能而被广泛用于催化剂^[1]、电池电极^[2,3]、光电转化材料^[4～6]、电化学电容器^[7～8]等诸多方面.迄今,已成功地制备出N iO的纳米颗粒^[9]、纳米线^[10]及纳米薄膜^[11],但是对于具有准一维结构的NiO纳米纤维的制备及性能研究尚未见报道.     

静电纺丝法制备Y2O3纳米纤维与表征

采用静电纺丝法制备了PVA/Y(NO3)3复合纳米纤维,在适当的温度下进行热处理,得到Y2O3纳米纤维. 利用XRD,SEM,TG-DTA,FTIR等现代分析手段对样品进行了表征. XRD分析表明,PVA/Y(NO3)3复合纤维为无定型,焙烧温度在600 ℃以上得到晶态单相的Y2O3纳米纤维,属于立方晶系,空间群为Ia3. SEM分析表明,PVA/Y(NO3)3复合纤维表面光滑,平均直径为110 nm. 焙烧温度对Y2O3纳米纤维的形成有重要影响. 600 ℃焙烧得到的Y2O3纳米纤维的平均直径约50 nm,900 ℃焙烧得到的Y2O3纳米纤维由纳米颗粒堆积而成,部分已断裂. TG-DTA和FTIR分析表明,PVA,Y(NO3)3以及水分在600 ℃以上时完全分解挥发,最终样品为晶态单相的Y2O3纳米纤维.     

静电纺丝法和气流-静电纺丝法制备聚砜纳米纤维

应用电纺法制备了聚砜纳米纤维.设计了一种新型的气流静电纺丝装置,其特点是在喷丝头上添加了喷气组件.电纺过程中所用聚砜的特性粘数为0.97dLg,溶剂为二甲基乙酰胺,载气为氮气.研究了聚砜纳米纤维的平均直径与过程参数之间的关系.研究表明影响聚砜纳米纤维的平均直径的主要因素为电压、纺丝液的流速、喷丝头与收集器之间的距离、操作温度以及纺丝液的性质(如粘度、表面张力和电导率).纳米纤维的平均直径和直径分布用扫描电镜表征.应用这种气流静电纺丝法制备的纳米纤维的直径范围是50～500nm.所得纳米纤维的直径依赖于电压、喷丝头与收集器之间的距离以及喷丝液的浓度.结果表明,采用气流静电纺丝不仅能制备较细而且均匀的纳米纤维,而且产量更高.     

静电纺丝法制备Mn_2O_3纳米纤维及其磁性研究

采用溶胶-凝胶过程和静电纺丝技术相结合方法, 以聚丙烯腈和醋酸锰为前驱物, 制得了PAN/Mn(CH₃COO)₂复合纳米纤维. 将该复合纤维高温煅烧, 获得了Mn₂O₃纳米纤维. 采用扫描电镜(SEM)、红外光谱(FTIR)、差热-热重(TG-DTA)和X射线衍射(XRD)分析等对样品进行了表征. 结果表明, Mn₂O₃纳米纤维为规则的一维结构, 直径分布均匀, 具有铁磁性-反铁磁性-顺磁性相互转化的特性.     

氮化硼催化低碳烷烃氧化脱氢的活性起源探讨（英文）

页岩气的急速开采推动了以天然气替代石油的资源革命.除主组分甲烷外,天然气、页岩气中还包含大量乙烷、丙烷等低碳烷烃资源,将这些储量丰富的碳资源直接转化为烯烃等基础化学品有望革新以原油为基础的化学工业.现有烷烃催化脱氢制烯烃工艺中,直接脱氢过程吸热、热力学受限,且存在催化剂迅速失活的难题;而氧化脱氢是放热过程、无平衡限制,也无积碳等引发催化剂失活的问题,有利于提高反应效率、降低能耗,代表了更为高效和经济的新路线.但作为一个热力学爬坡过程,目前金属氧化物催化剂上烯烃产物很容易深度氧化到CO_2,选择性仍有待提高.非金属氮化硼能够有效活化低碳烷烃中的C-H键,促进烷烃氧化脱氢,并能够有效抑制深度氧化产物的生成,解决低碳烷烃临氧脱氢过程中产物易深度氧化的固有难题.本文综述了近期氮化硼在乙烷、丙烷、丁烷等低碳烷烃氧化脱氢制烯烃反应中的研究进展.以丙烷氧化脱氢为例,通过比较文献报道的几种氮化硼材料的氧化脱氢性能,发现羟基化氮化硼显示了最高的烯烃选择性和时空收率,以20.6%的丙烷转化率为基准,烯烃选择性超过90%,而时空收率可达6.8 golefin gcat~(-1) h~(-1).在此基础上,本文重点讨论了对于氮化硼材料催化活性起源的认识.主要实验事实和结论包括:氮化硼自身几乎没有氧化脱氢活性,而在烷烃氧化脱氢反应条件下存在活性诱导期;活性诱导期伴随着氮化硼边沿氧官能团化过程;氮化硼边沿B-O官能团没有脱氢活性,而B-OH官能团参与了氧化脱氢过程,辅助分子氧引发低碳烷烃脱氢反应;分子氧在羟基氮化硼边沿解离活化,反应过程中与边沿结构氧存在动态交换;氮化硼边沿羟基化定向合成过程可显著增强氧化脱氢反应活性.氮化硼作为一类新型烷烃氧化脱氢催化剂,目前正处于研究的初始阶段.因此,本文最后总结了一些关于氮化硼烷烃脱氢催化体系仍需深入研究的科学问题.     

Selective fabrication of porous iron oxides hollow spheres and nanofibers by electrospinning for photocatalytic water purification

Porous hematite (α-Fe₂O₃) hollow spheres and nanofibers could be obtained via electrospinning and subsequent thermal decomposition in air. The precursor could be fabricated by electrospinning using Fe(NO₃)₃ as the iron source and Polyvinylpyrrolidone (PVP) as a complexing reagent. Upon calcination, pure porous α-Fe₂O₃ hollow spheres and nanofibers could be obtained at 650 °C for 3 h. The novel hollow spheres have an abundantly porous structure as well as large surface areas. Benefitting from the special porous structure, narrow bandgap, and higher surface area, porous α-Fe₂O₃ hollow materials are used as visible-light-responsive photocatalysts. So we have investigated the visible light photodegradation behavior of porous hematite (α-Fe₂O₃) hollow spheres and nanofibers towards organic dyes, as Rhodamine B (RhB). The synergetic effects of higher surface area, pore structures promoted the photocatalytic efficiency for RhB degradation under visible light and contributed to achieving the enhanced and stable photocatalytic activity.     

Electrospinning and characterization of medium-molecular-weight poly(vinyl alcohol)/high-molecular-weight poly(vinyl alcohol)/montmorillonite nanofibers

Submicron fibers of medium-molecular-weight poly(vinyl alcohol) (MMW-PVA), high-molecular-weight poly(vinyl alcohol) (HMW-PVA), and montmorillonite clay (MMT) in aqueous solutions were prepared by electrospinning technique. The effect of HMW-PVA and MMT on the morphology and mechanical properties of the MMW-PVA/HMW-PVA/MMT nanofibers were investigated for the first time. Scanning electron microscopy, viscometer, tensile strength testing machine, thermal gravimetric analyzer (TGA), and transmission electron microscopy (TEM) were utilized to characterize the PVA/MMT nanofibers morphology and properties. The MMW-PVA/HMW-PVA ratios and MMT concentration played important roles in nanofiber's properties. TEM data demonstrated that exfoliated MMT layers were well distributed within nanofibers. It was also found that the mechanical property and thermal stability were increased with HMW-PVA and MMT contents.     

Aerobic oxidative dehydrogenation of N-heterocycles catalyzed by cobalt porphyrin

An efficient catalytic procedure has been developed for the aerobic oxidative dehydrogenation of N-heterocycles by cobalt porphyrin in the absence of any additives. The catalytic system could tolerate various 1,2,3,4-tetrahydroquinoline derivatives and some other N-heterocycles. The corresponding N-heteroaromatics could be obtained in 59–86% yields. The mechanism investigation suggested that the aerobic oxidative dehydrogenation might proceed with imine intermediate through radical paths.     

Studies on the oxidative dehydrogenation of propane to propene over Co-V-O catalysts

A series of Co-V-O catalysts were prepared and their catalytic performances for the oxidative dehydrogenation of propane to propene were investigated. It was found that the p-type catalysts showed higher catalytic behavior than the n-type catalyst.     

Electrospinning fabrication of partially crystalline bisphenol A polycarbonate nanofibers: Effects on conformation, crystallinity, and mechanical properties

The application of an electrostatic and centrifugal field (1800 rpm) in a novel electrospinning process was shown to improve the degree of uniaxial alignment in polymer nanofibers and to enhance orientational order in polymer chains, producing bisphenol A polycarbonate (BPAPC) nanofibers with superior mechanical properties. High-speed videography showed that the additional centrifugal field effectively removed electrical bending instability and promoted molecular orientation during the electrospinning process. Infrared spectroscopic (IR) characterization revealed that the fraction of trans–trans conformers in BPAPC nanofibers reached 67% under optimal electrospinning conditions (25 kV and 1800 rpm at 25 °C). Modulated differential scanning calorimetry (MDSC) and wide-angle X-ray diffraction (WXRD) assays showed that a degree of crystallinity of 6.5% could be achieved. Moreover, two crystal phases at angles of 2θ = 17.3° and 21.9° were produced in BPAPC nanofibers. The elastic modulus of BPAPC nanofibers with a crystallinity of 6.5% was 7.11 and 5.13 GPa, as measured via atomic force microscopy (AFM) and nanoindenter (NI) experiments, respectively. These results demonstrated that the mechanical behavior of BPAPC nanofibers could be improved by conducting the proposed electrospinning technique. Moreover, BPAPC nanofibers produced through the proposed method could be potentially applied for the reinforcement of composites.     

Novel KF-TiO2catalysts for oxidative dehydrogenation of isobutane

A novel type of catalysts, KF-TiO₂, efficient for the oxidative dehydrogenation (ODH) of isobutane is presented. The effect of KF content and calcination temperature was studied. In the reaction conditions explored, the best performance (73 % selectivity to isobutene at 10.5 % conversion of isobutane) was observed over a catalyst with KF/TiO₂ = 0.2 (mol/mol). The surface properties of the catalysts were investigated by SPS (Surface Photo-voltage Spectroscopy) and XPS. The promotion effect of KF in the catalysts can be attributed to the formation of an oxyfluoro-compound, K₂Ti₄O₈F₂.     

A review of opportunities for electrospun nanofibers in analytical chemistry

Challenges associated with analyte and matrix complexities and the ever increasing pressure from all sectors of industry for alternative analytical devices, have necessitated the development and application of new materials in analytical chemistry. To date, nanomaterials have emerged as having excellent properties for analytical chemistry applications mainly due to their large surface area to volume ratio and the availability of a wide variety of chemical and morphological modification methods. Of the available nanofibrous material fabrication methods, electrospinning has emerged as the most versatile. It is the aim of this contribution to highlight some of the recent developments that harness the great potential shown by electrospun nanofibers for application in analytical chemistry. The review discusses the use of electrospun nanofibers as a platform for low resolution separation or as a chromatographic sorbent bed for high resolution separation. It concludes by discussing the applications of electrospun nanofibers in detection systems with a specific focus on the development of simple electrospun nanofiber based colorimetric probes.     

Aerobic oxidative dehydrogenation of coordinated imidazoline units of pincer ruthenium complex

A new pincer ruthenium complex (1; [RuL¹(tpy)](PF₆); L¹ = 1,3-di(2-imidazoline-2-yl)benzene, tpy = 2,2′:6′,2″-terpyridine) having a κ³NCN pincer ligand with two imidazoline units and related ruthenium complexes were synthesized and characterized. The imidazoline units of 1 were oxidized in air to give an imidazole-ligated pincer complex (2; [RuL²(tpy)](PF₆); L² = 1,3-di(2-imidazolyl)benzene). Results of the ¹H NMR spectroscopic and cyclic voltammetric studies of the complexes indicate that the σ-donor character of the pincer ligand of 1 induces the Ru-promoted oxidative dehydrogenation of coordinated imidazoline moieties to imidazole units with oxygen in air.     

A practical grinding-assisted dry synthesis of nanocrystalline NiMoO4 polymorphs for oxidative dehydrogenation of propane

A practical two-stage reactive grinding-assisted pathway waste-free and cost-effective for the synthesis of NiMoO₄ has been successfully developed. It was demonstrated that proper design in synthetic strategy for grinding plays a crucial role in determining the ultimate polymorph of NiMoO₄. Specifically, direct grinding (DG) of MoO₃ and NiO rendered α-NiMoO₄ after annealing, whereas sequential grinding (SG) of the two independently pre-ground oxides followed by annealing generated β-NiMoO₄ solid solution. Characterizations in terms of Raman and X-ray diffraction suggest the creation of β-NiMoO₄ precursor in the latter alternative is the key aspect for the formation of β-NiMoO₄. The DG-derived α-NiMoO₄ tested by oxidative dehydrogenation of propane exhibited superior activity in contrast to its analog synthesized via conventional coprecipitation. It is suggested that the favorable chemical composition facilely obtained via grinding in contrast to that by coprecipitation was essential for achieving a more selective production of propylene.