A SERS-active microfluidic device with tunable surface plasmon resonances

A surface-enhanced Raman scattering (SERS)-active microfluidic device with tunable surface plasmon resonances is presented here. It is constructed by silver grating substrates prepared by two-beam laser interference of photoresists and subsequent metal evaporation coating, as well as PDMS microchannel derived from soft lithography. By varying the period of gratings from 200 to 550 nm, surface plasmon resonances (SPRs) from the metal gratings could be tuned in a certain range. When the SPRs match with the Raman excitation line, the highest enhancement factor of 2×10(7) is achieved in the SERS detection. The SERS-active microchannel with tunable SPRs exhibits both high enhancement factor and reproducibility of SERS signals, and thus holds great promise for applications of on-chip SERS detection.     

Quantitative SERS sensors for environmental analysis of naphthalene

In the investigation of chemical pollutants, such as PAHs (Polycyclic Aromatic Hydrocarbons) at low concentration in aqueous medium, Surface-Enhanced Raman Scattering (SERS) stands for an alternative to the inherent low cross-section of normal Raman scattering. Indeed, SERS is a very sensitive spectroscopic technique due to the excitation of the surface plasmon modes of the nanostructured metallic film. The surface of quartz substrates was coated with a hydrophobic film obtained by silanization and subsequently reacted with polystyrene (PS) beads coated with gold nanoparticles. The hydrophobic surface of the SERS substrates pre-concentrates non-polar molecules such as naphthalene. Under laser excitation, the SERS-active substrates allow the detection and the identification of the target molecules localized close to the gold nanoparticles. The morphology of the SERS substrates based on polystyrene beads surrounded by gold nanoparticles was characterized by scanning electron microscopy (SEM). Furthermore, the Raman fingerprint of the polystyrene stands for an internal spectral reference. To this extent, an innovative method to detect and to quantify organic molecules, as naphthalene in the range of 1 to 20 ppm, in aqueous media was carried out. Such SERS-active substrates tend towards an application as quantitative SERS sensors for the environmental analysis of naphthalene.     

Aspect ratio dependence on surface enhanced Raman scattering using silver and gold nanorod substrates

Silver and gold nanorods with aspect ratios from 1 to 16 have been used as substrates for surface enhanced Raman spectroscopy (SERS) in colloidal solution. The nanorod aspect ratio is varied to give different degrees of overlap between the nanorod longitudinal plasmon band and excitation source in order to determine its effect on overall surface enhancement. Results suggest that enhancement factors are a factor of 10-10(2) greater for substrates that have plasmon band overlap with the excitation source than for substrates whose plasmon bands do not.     

Detection of proteins on silica-silver core-shell substrates by surface-enhanced Raman spectroscopy

We have employed the proposed Silica-Silver Core-Shell (SSCS) SERS-active substrates to detect four model proteins: lysozyme (a protein without chromophore), cytochrome c (a protein with chromophore of heme), fluorescein isothiocyanate (FITC)-anti human IgG (labeled with FITC) and atto610-biotin/avidin (recognition with labeled small molecules). SERS spectra of these proteins and Raman labels on the SSCS substrates show both high sensitivity and reproducibility, which are due to electromagnetic SERS enhancement with additional localization field within closely packed Ag nanoparticles decorated on the SiO(2) nanoparticles and the aggregation of SiO(2)@Ag particles. We have found that the SERS intensities of atto610-biotin/avidin adsorbed on the SSCS substrates are about 20 times stronger than those from Ag plating on Au-decorated substrate. Moreover, the broad surface plasmon resonance (SPR) of the proposed substrates will extend SERS applications to more biological molecules with different laser excitations.     

表面增强拉曼散射活性基底

表面增强拉曼散射(SERS)是人们将激光拉曼光谱应用到表面科学研究中所发现的异常表面光学现象。它可以将吸附在材料表面的分子的拉曼信号放大106到1014倍,这使其在探测器的应用和单分子检测方面有着巨大的发展潜力。由于分子所吸附的基底表面形态是SERS效应能否发生和SERS信号强弱的重要影响因素,所以分子的承载基体是很关键的,因而SERS活性基底的研究一直是该领域的研究热点之一。本文总结了形态各异的表面增强拉曼散射活性基底,分析了最新发展并对其未来作一展望。     

Tailoring plasmonic substrates for surface enhanced spectroscopies

Our understanding of how the geometry of metallic nanostructures controls the properties of their surface plasmons, based on plasmon hybridization, is useful for developing high-performance substrates for surface enhanced spectroscopies. In this tutorial review, we outline the design of metallic nanostructures tailored specifically for providing electromagnetic enhancements for surface enhanced Raman scattering (SERS). The concepts developed for nanoshell-based substrates can be generalized to other nanoparticle geometries and scaled to other spectroscopies, such as surface enhanced infrared absorption spectroscopy (SEIRA).     

Electrochemical pathway for the quantification of SERS enhancement factor

This communication presents a new pathway for the more precise quantification of surface-enhanced Raman scattering (SERS) enhancement factor via deducing resonance Raman scattering (RRS) effect from surface-enhanced resonance Raman scattering (SERRS). To achieve this, a self-assembled monolayer of 1,8,15,22-tetraaminophthalocyanatocobalt(II) (4α-Co^IITAPc) is formed on plasmon inactive glassy carbon (GC) and plasmon active GC/AuNP surface. The surfaces are subsequently used as common probes for electrochemical and Raman (RRS and SERRS) studies. The most crucial parameters required for the quantification of SERS substrate enhancement factor (SSEF) such as real surface area of GC/AuNPs substarte and the number of 4α-Co^IITAPc molecules contributing to RRS (on GC) and SERRS (on GC/AuNPs) are precisely estimated by cyclic voltammetry experiments. The present approach of SSEF quantification can be applied to varieties of surfaces by choosing an appropriate laser line and probe molecule for each surface.     

Surface-enhanced Raman scattering substrates fabricated using electroless plating on polymer-templated nanostructures

Surface-enhanced Raman scattering (SERS) has great potential as an analytical technique based on the unique molecular signatures presented even by structurally similar analyte species and the minimal interference of scattering from water when sampling in aqueous environments. Unfortunately, analytical SERS applications have been restricted on the basis of limitations in substrate design. Herein, we present a simple SERS substrate that exploits electroless deposition onto a nanoparticle-seeded polymer scaffold that can be fabricated quickly and without specialized equipment. The polymer-templated nanostructures have stable enhancement factors that are comparable to the traditional silver film over nanospheres (AgFON) substrate, broad localized surface plasmon resonance spectra that allow various Raman excitation wavelengths to be utilized, and tolerance for both aqueous and organic environments, even after 5 day exposure. These polymer-templated nanostructures have an advantage over the AgFON substrate based on the ease of fabrication; specifically, the ability to generate fresh SERS substrates outside the laboratory environment will facilitate the application of SERS to new analytical spectroscopy applications.     

Chiral Carbonaceous Nanotubes Modified with Titania Nanocrystals: Plasmon‐Free and Recyclable SERS Sensitivity

Chiral carbonaceous nanotubes (CNT) were successfully used in plasmon‐free surface‐enhanced Raman scattering (SERS) for the first time. Further modification of TiO₂ nanocrystals on the chiral CNTs successfully realized the recycling of SERS substrate as chiral CNT/TiO₂ hybrids. The high SERS sensitivity of methylene blue (MB) over the chiral CNT/TiO₂ hybrids is ascribed to the laser‐driven birefringence induced by the helical structure, which provides much more opportunities for the occurrence of Raman scattering. The TiO₂ nanocrystals highly dispersed on the surface and inside the hollow cavity of chiral CNTs can completely degrade the MB under the solar light irradiation, leading to the self‐cleaning of SERS substrate. The present research opens a new way for the application of chiral inorganic materials in plasmon‐free SERS detection.     

Gold films deposited over regular arrays of polystyrene nanospheres as highly effective SERS substrates from visible to NIR

Gold nanostructured films of various thicknesses (15, 30, and 60 nm) are deposited over regular arrays of polystyrene nanospheres in an attempt to evaluate their potential as SERS-active substrates. Atomic force microscopy is used to topographically characterize the substrates as well as to ensure the thickness of the deposited gold films. The optical response of the prepared substrates recommends their use in SERS experiments with multiple laser lines from visible and NIR spectral domains. The assessment of the substrates' SERS activity is performed by using the 532, 633, and 830 nm excitation lines and different average enhancement factor (EF) values are obtained depending on the film thickness and employed laser line. The 60 nm gold nanostructured film generates the greatest local electromagnetic field confinement under NIR excitation and consequently gives rise to maximum SERS enhancement. The large tunability of surface plasmon excitation combined with the advantage of relatively high exhibited average EF values obtained under NIR excitation recommends these substrates as outstanding candidates for upcoming investigations of biological relevant molecules.     

Effect of Ag and Au nanoparticles on the SERS of 4-aminobenzenethiol assembled on powdered copper

Raman scattering measurements were conducted for 4-aminobenzenethiol (4-ABT) assembled on powdered copper substrates. Initially, very weak Raman peaks were detected, but upon attaching Ag nanoparticles probably via NH2 groups onto 4-ABT/Cu, distinct Raman spectra were observed. Considering the fact that no Raman peak was identified when Ag nanoparticles were adsorbed on 4-aminophenyl-derivatized silane monolayers assembled on silica powders, the Raman spectra observed for Ag@4-ABT/Cu should be surface-enhanced Raman scattering (SERS) spectra, occurring by an electromagnetic coupling of the localized surface plasmon of Ag nanoparticles with the surface plasmon polariton of Cu powders. The extra enhancement factor attainable by the attachment of a single Ag nanoparticle is estimated to be as large as 1.4 x 10(5) in the case when 632.8-nm radiation is used as the excitation source. When Au nanoparticles were attached onto 4-ABT/Cu, at least an order of magnitude weaker Raman spectra were obtained at all excitation wavelengths, however, indicating that the Au-to-Cu coupling should be far less effective than the Ag-to-Cu coupling for the induction of SERS.     

基于自组装纳米金单层膜的全内反射SERS研究

采用静电自组装技术分别在玻璃基片和30 nm厚的金膜表面固定一层金纳米粒子(GNP)制得两种表面增强拉曼散射(SERS)基底,然后通过棱镜全内反射(TIR)激励和背向收集模式分别测试了两种基底上吸附的染料单分子层SERS光谱.实验结果表明两种SERS基底的拉曼增强效果均高度依赖于入射激光的偏振状态,对于玻璃/纳米金SERS基底,s光全内反射导致的拉曼增强因子是线偏振光(p)光的2-5倍,说明该基底上的"热点"位于纳米金单层膜内相邻粒子之间;对于玻璃/金膜/纳米金SERS基底,只有采用p光在特定的全内反射角下才能激发SERS信号,而且测得的SERS信号比玻璃/纳米金基底增强了近30倍.究其原因是p光在金膜表面共振激发的传播表面等离子体与纳米金局域表面等离子体耦合,进而导致显著场增强.实验结果指出在背向收集模式下,由p光激发的SERS信号是非偏振光,包含强度几乎相等的s和p成分.利用玻璃/金膜/纳米金基底还实现了拉曼光定向发射和收集,测得的SERS信号是p光.     

基于自组装纳米金单层膜的全内反射SERS研究

采用静电自组装技术分别在玻璃基片和30 nm厚的金膜表面固定一层金纳米粒子（GNP）制得两种表面增强拉曼散射（SERS）基底,然后通过棱镜全内反射（TIR）激励和背向收集模式分别测试了两种基底上吸附的染料单分子层SERS光谱. 实验结果表明两种SERS基底的拉曼增强效果均高度依赖于入射激光的偏振状态,对于玻璃/纳米金SERS基底,s 光全内反射导致的拉曼增强因子是线偏振光（p）光的2-5 倍,说明该基底上的“热点”位于纳米金单层膜内相邻粒子之间;对于玻璃/金膜/纳米金SERS基底,只有采用p光在特定的全内反射角下才能激发SERS信号,而且测得的SERS信号比玻璃/纳米金基底增强了近30 倍. 究其原因是p 光在金膜表面共振激发的传播表面等离子体与纳米金局域表面等离子体耦合,进而导致显著场增强. 实验结果指出在背向收集模式下,由p 光激发的SERS信号是非偏振光,包含强度几乎相等的s 和p 成分. 利用玻璃/金膜/纳米金基底还实现了拉曼光定向发射和收集,测得的SERS信号是p光.     

Gold Nanowire Forests for SERS Detection

Simple wet chemistry has been applied to control the vertical growth of gold nanowires on a glass substrate. As a consequence, the longitudinal localized surface plasmon band position can be tuned from 656 to 1477 nm in a few minutes by simply controlling the growth rate and time. This allowed us to select the optimum conditions for maximum electromagnetic enhancement and performance in surface enhanced Raman scattering (SERS) detection. SERS measurements confirmed the uniform and reproducible distribution of the nanowires on the substrate, with the subsequent high reproducibility of hot spot formation. Detection of malachite green in water and of 1-naphthalenethiol from the gas phase are demonstrated as proof-of-concept applications of these three-dimensional SERS substrates.     

Silver Nano Islands Enhanced Raman Scattering on Large Area Grating Substrates Fabricated by Two Beam Laser Interference

The authors preparedlarge area surface-enhanced Raman scattering(SERS) active substrates with tunable enhancement. First the large area gratings were fabricated by scanning a photoresist with two-beam laser interference and subsequently they were coated with silver nano islands via vacuum evaporation. SERS active metal island grating substrates with four different periods(300, 400, 515 and 600 nm) and Ag nano islands uniformly coated on an area of 2.5 cm×0.5 cm were obtained. The measured SERS spectra reveal the tuning effect of the period on the Raman signals period. The highest enhancement(ca. 10⁵) for Rhodamine 6G(R6G) as probing molecule is associated with a period of 515 nm due to the perfect matching of surface plasmons and Raman excitation line. A good reproducibility of SERS signals with almost the same SERS intensity at different spots was observed on all the larger area Ag island grating substrates.     

Self-assembled silver nanochains for surface-enhanced Raman scattering

Surface-enhanced Raman scattering (SERS) integrates high levels of sensitivity with spectroscopic precision and has tremendous potential for chemical and biomolecular sensing. The key to the wider application of Raman spectroscopy using roughened metallic surfaces is the development of highly enhancing substrates for analytical purposes. Here, we demonstrate a simple strategy for self-assembling silver nanochains on glass substrates for sensitive SERS substrates. The chain length of short Ag nanochains can be controlled by adjusting the concentration of cetyltrimethylammonium bromide (CTAB) and 11-mercaptoundecanoic acid (MUA). CTAB with appropriate concentration serves as the "glue" that can link the {100} facets of two neighboring Ag nanoparticles. MUA is found to be effective in "freezing up" the aggregation of Ag short chains and preventing them from further aggregating into a long chainlike network structure. The surface plasmon bands can be tuned over an extended wavelength range by controlling the length of the nanochains. The Ag monolayer, mainly composed of four-particle nanochains, exhibited the maximum SERS enhancement factor of around 2.6 x 108, indicating that a stronger SERS enhancement can be obtained in these interstitial sites of chainlike aggregated Ag nanoparticles.     

Nanoparticle-mirror sandwich substrates for surface-enhanced Raman scattering

Sandwich surface-enhanced Raman scattering (SERS) substrates (3S) utilizing coupling between continuous metal films and plasmonic particles were fabricated using silver mirrors, electrochemically roughened films, and various sizes of silver nanoparticles. The effect of excitation wavelength and nanoparticle size on SERS spectra of poly(vinylpyridine), selected as a model compound, was studied to determine the optimum conditions for the strongest SERS signal. The Raman enhancement resulted from the plasmon coupling of silver nanoparticles to the underlying continuous film as well as the lateral plasmon coupling between the silver nanoparticles. The formation of the charge transfer complex was also observed. The 3S configuration was used to obtain SERS spectra of dipicolinic acid (DPA), a chemical signature for Bacillus anthracis.     

Noble‐Metal‐Free Materials for Surface‐Enhanced Raman Spectroscopy Detection

Surface‐enhanced Raman spectroscopy (SERS) is an attractive tool for the sensing of molecules in the fields of chemical and biochemical analysis as it enables the sensitive detection of molecular fingerprint information even at the single‐molecule level. In addition to traditional coinage metals in SERS analysis, recent research on noble‐metal‐free materials has also yielded highly sensitive SERS activity. This Minireview presents the recent development of noble‐metal‐free materials as SERS substrates and their potential applications, especially semiconductors and emerging graphene‐based nanostructures. Rather than providing an exhaustive review of this field, possible contributions from semiconductor substrates, characteristics of graphene enhanced Raman scattering, as well as effect factors such as surface plasmon resonance, structure and defects of the nanostructures that are considered essential for SERS activity are emphasized. The intention is to illustrate, through these examples, that the promise of noble‐metal‐free materials for enhancing detection sensitivity can further fuel the development of SERS‐related applications.     

Combined SPR and SERS microscopy in the Kretschmann configuration

A novel hybrid spectroscopic technique is proposed, combining surface plasmon resonance (SPR) with surface-enhanced Raman scattering (SERS) microscopy. A standard Raman microscope is modified to accommodate the excitation of surface plasmon-polaritons (SPPs) on flat metallic surfaces in the Kretschmann configuration, while retaining the capabilities of Raman microscopy. The excitation of SPPs is performed as in standard SPR-microscopy; namely, a beam with TM-polarization traverses off-axis a high numerical aperture oil immersion objective, illuminating at an angle the metallic film from the (glass) substrate side. The same objective is used to collect the full Kretschmann cone containing the SERS emission on the substrate side. The angular dispersion of the plasmon resonance is measured in reflectivity for different coupling conditions and, simultaneously, SERS spectra are recorded from Nile Blue (NB) molecules adsorbed onto the surface. A trade-off is identified between the conditions of optimum coupling to SPPs and the spot size (which is related to the spatial resolution). This technique opens new horizons for SERS microscopy with uniform enhancement on flat surfaces.     

小尺寸金石墨纳米颗粒的合成与表征

在表面增强拉曼光谱(SERS)的研究领域中,基于局域表面等离子体共振效应的等离子体SERS基底的制备成为过去几十年的研究热点。然而,通常开发的等离子体金属基底具有较差的稳定性和重现性。对于SERS而言,石墨烯类材料具有拉曼化学增强效应,除此之外,还具有分子富集、强的稳定性与荧光猝灭能力等优点,因此基于石墨金属复合纳米材料的SERS基底受到了研究人员的重视。我们利用化学气相沉积(CVD)法制备了小尺寸的金石墨核壳纳米颗粒(Au@G),其粒径约为17 nm。我们通过在Au NP上包覆介孔二氧化硅来控制Au@G的尺寸,同时还研究了包覆二氧化硅过程中,正硅酸乙酯(TEOS)的浓度对于石墨壳层形成的影响。结果表明当TEOS在一定浓度范围内,其浓度的降低有利于得到石墨化程度高的Au@G。进一步利用Au@G对结晶紫分子进行拉曼检测,也表明了Au@G具有较好的拉曼增强效果。这种小尺寸的Au@G在分子检测与细胞成像分析领域中具有广泛的应用潜力。