Development of imprinted materials for the selective extraction of nitroaromatic explosives

Molecularly imprinted sorbents were synthesized and used as selective extraction sorbents for the analysis of nitroaromatic explosives. Their synthesis by radical polymerization using organic monomers and by sol–gel approach using organosilanes was considered to develop a selective sorbent. The sol–gel approach with phenyltrimethoxysilane (PTMS) as monomer and 2,4-dinitrotoluene (2,4-DNT) as template gave the most promising results. An optimized procedure adapted to the selective treatment of aqueous samples was then developed and applied to various target explosives. For the first time four nitroaromatic compounds were retained on the molecularly imprinted silica (MIS) with extraction recoveries between 29% and 81%, while only low recoveries were obtained on the non-imprinted sorbent, thus highlighting the high degree of selectivity. The MIS was then used for the clean-up of a sample containing motor oil spiked with 2,4-DNT and 2,4,6-trinitrotoluene (2,4,6-TNT). The results were compared with those obtained using a conventional sorbent (Oasis HLB). The cleanest chromatogram obtained using the MIS emphasized the high potential of the MIS as selective sorbent.     

Selective extraction of nitroaromatic explosives by using molecularly imprinted silica sorbents

Two molecularly imprinted silicas (MISs) were synthesized and used as selective sorbents for the extraction of nitroaromatic explosives in post-blast samples. The synthesis of the MISs was carried out with phenyltrimethoxysilane as monomer, 2,4-dinitrotoluene (2,4-DNT) as template and triethoxysilane as cross-linker by a sol–gel approach in two molar ratios: 1/4/20 and 1/4/30 (template/monomer/cross-linker). Non-imprinted silica sorbents were also prepared following the same procedures without introducing the template. An optimized procedure dedicated to the selective treatment of aqueous samples was developed for both MISs for the simultaneous extraction of the template and other nitroaromatic compounds commonly used as explosives. The capacity of the MISs was measured by the extraction of increasing amounts of 2,4-DNT in pure water and is higher than 3.2 mg/g of sorbent for each MIS. For the first time, four nitroaromatic compounds were selectively extracted and determined simultaneously with extraction recoveries higher than 79%. The potential of these sorbents was then highlighted by their use for the clean-up of post-blast samples (motor oil, post-mortem blood, calcined fragments, etc.). The results were compared to those obtained using a conventional sorbent, thus demonstrating the interest of the use of these MISs as selective sorbents.     

Determination of Explosives in Water Using Disposable Pipette Extraction and High Performance Liquid Chromatography

The use of disposable pipette extraction was examined for the simple and rapid determination of seven high explosives (cyclotrimethyl-enetrinitramine, cyclotetramethyl-enetetranitramine, 2,4,6-trinitrophenyl-methylnitramine, 2,4,6-trinitrotoluene, 2,4-dinitrotoluene, nitroglycerin, and pentaerythritol tetranitrate) in water. The current study involved the determination of slightly polar and nonpolar explosives in water with a reversed phase sorbent followed by high performance liquid chromatography. The method was based on a styrene divinylbenzene sorbent loosely placed inside a 5-mL pipette tip. Water samples were drawn into the tip and mixed with the sorbent. Air bubbles were also drawn through the tip following sample solution to enhance mixing. Because disposable pipette extraction uses small amounts of sorbent, minimal solvent is required to elute analytes and solvent evaporation is not necessary. The method provided rapid sample preparation, and required less than five minutes to extract 1.0 mL of water sample in the current study. Matrix-matched calibration was performed, and the limits of detection (LOD) were determined to be below 0.1 µg mL^?1 for all targeted explosives in water with an enrichment factor of two. Coefficients of determination (r²) were greater than 0.9990 for all studied explosives, and the recoveries ranged from 69.76% to 87.51%, 83.77% to 91.25%, and 83.62% to 98.99% for samples spiked at 0.25 µg mL^?1, 1.0 µg mL^?1, and 5.0 µg mL^?1, respectively. The relative standard deviations of recoveries at all spiked levels were below 8.97%. These results indicate that the disposable pipette extraction method provided good accuracy and precision for the determination of explosives in water.     

Solubility parameter used to predict the effectiveness of monolithic in-needle extraction (MINE) device for the direct analysis of liquid samples

The sorbent/eluent systems combined from three macroporous poly(styrene–divinylbenzene) (PS-DVB) monoliths and four solvents as eluents were used for the extraction of phenol, 4-chlorophenol and p-benzochinon from water samples. Monolithic in-needle extraction (MINE) devices were used in the preparation of a series of test water samples for chromatographic analysis. The extraction of phenolic compounds from water samples was carried out by pumping liquid samples through the MINE device. Solubility parameter concept was applied for estimation of effectiveness of MINE. Solubility parameters for (PS-DVB) monoliths were determined according to Small, considering different molar fraction of the monomers used for synthesis. Effectiveness of these systems was estimated according to difference of solubility parameter value in analyte/sorbent, sorbent/eluent, analyte/eluent pairs. The procedure enabling easy prediction of, e.g. the strength of the interactions between the analyte and sorbent, eluent efficiency or the extraction efficiency in MINE system was proposed.     

Sol-gel molecular imprinted ormosil for solid-phase extraction of methylxanthines

A organically modified molecularly imprinted silica (MIS), selective for methylxanthines, was prepared using a simple sol-gel procedure. Caffeine was used as template; 3-aminopropyltrimethoxysilane (APTMS) as functional monomer and tetraethyl orthosilicate (TEOS) as reticulating agent. The material was packed on solid-phase extraction (SPE) cartridges and evaluated with aqueous test samples, natural water and human urine; a quantitative method for methylxanthines in water, using SPE cartridges packed with the MIS coupled with HPLC-UV was developed. The MIS was highly specific for methylxanthines, with an imprinting factor of (20.5+/-1.9). The analytical method resulted in detection limits of 85 microgL(-1) for theobromine, 44 microgL(-1) for theophylline and 53 microgL(-1) for caffeine.     

Trace analysis of explosives in soil: pressurized fluid extraction and gas and liquid chromatography-mass spectrometry

Soil samples are collected from the former Open Burn/Open Detonation Unit, Makua Military Reservation, on the island of Oahu, Hawaii. The soil is the Helemano series. The soil samples are fortified with eight explosives for development of the analytical method. These analytes are 2-amino-4,6-dinitrotoluene; 1,3-dinitrobenzene; 2,4-dinitrotoluene (DNT); hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX); nitrobenzene (NB); octogen; 1,3,5-trinitrobenzene; and 2,4,6-trinitrotoluene. The analytes are recovered with pressurized fluid extraction and measured with liquid chromatography (LC), LC-mass spectrometry (MS), and gas chromatography-MS. Average recoveries of the seven analytes, except for NB, range from 67% to 110% from freshly fortified samples. The procedure fails to extract NB in soil. The average recoveries decrease from 67-110% to 41-81% as the soil is aged for 1 day to 6 months after fortification of the soil with the seven explosives. The field samples are analyzed for the presence of explosives, of which DNT and RDX are indeed detected. The results obtained with this procedure agree well with those obtained by an independent laboratory following the standard U.S. Environmental Protection Agency (EPA) method SW-846 8330. Compared with the EPA method, this new method provides MS confirmation of the analytes, and the extraction requires approximately 15 min, rather than 18 h by the EPA method.     

High-efficiency headspace sampling of volatile organic compounds in explosives using capillary microextraction of volatiles (CMV) coupled to gas chromatography–mass spectrometry (GC-MS)

A novel geometry configuration based on sorbent-coated glass microfibers packed within a glass capillary is used to sample volatile organic compounds, dynamically, in the headspace of an open system or in a partially open system to achieve quantitative extraction of the available volatiles of explosives with negligible breakthrough. Air is sampled through the newly developed sorbent-packed 2 cm long, 2 mm diameter capillary microextraction of volatiles (CMV) and subsequently introduced into a commercially available thermal desorption probe fitted directly into a GC injection port. A sorbent coating surface area of ～5?×?10^?2 m² or 5,000 times greater than that of a single solid-phase microextraction (SPME) fiber allows for fast (30 s), flow-through sampling of relatively large volumes using sampling flow rates of ～1.5 L/min. A direct comparison of the new CMV extraction to a static (equilibrium) SPME extraction of the same headspace sample yields a 30 times improvement in sensitivity for the CMV when sampling nitroglycerine (NG), 2,4-dinitrotoluene (2,4-DNT), and diphenylamine (DPA) in a mixture containing a total mass of 500 ng of each analyte, when spiked into a liter-volume container. Calibration curves were established for all compounds studied, and the recovery was determined to be ～1 % or better after only 1 min of sampling time. Quantitative analysis is also possible using this extraction technique when the sampling temperature, flow rate, and time are kept constant between calibration curves and the sample.     

Polytrimethylsilylpropyne as adsorbent for separation of gases

Polytrimethylpropyne supported on a solid substrate was proposed as a chromatographic adsorbent for the separation of hydrocarbon gases. The heats of adsorption of hydrocarbon gases were determined. The efficiency of application of this sorbent for the selective separation of C₁--C₄ hydrocarbon gases in packed columns was demonstrated.     

Use of reversed-phase high-performance liquid chromatography-diode array detection for complete separation of 2,4,6-trinitrotoluene metabolites and EPA Method 8330 explosives: influence of temperature and an ion-pair reagent

Explosives such as 2,4,6-trinitrotoluene (TNT), octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX), and hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX) are widely distributed environmental contaminants. Complete chromatographic separation is necessary in order to accurately determine and quantify explosives and their degradation products in environmental samples and in (bio)transformation studies. The present study describes a RP-HPLC method with diode array detection using a LC-8 guard column, a Supelcosil LC-8 chromatographic column, and a gradient elution system. This gradient method is capable of baseline separating the most commonly observed explosives and TNT transformation metabolites including 2,4,6-triaminotoluene (TAT) in a single run. The TNT metabolites separated were 2-hydroxylamino-4,6-dinitrotoluene, 4-hydroxylamino-2,6-dinitrotoluene, 2,4-dihydroxylamino-6-nitrotoluene, 4,4',6,6'-tetranitro-2,2'-azoxytoluene, 2,2',6,6'-tetranitro-4,4'-azoxytoluene, 4,4',6,6'-tetranitro-2,2'-azotoluene, 2,2',6,6'-tetranitro-4,4'-azotoluene, 2-amino-4,6-dinitrotoluene, 4-amino-2, 6-dinitrotoluene, 2,6-diamino-4-nitrotoluene, 2,4-diamino-6-nitrotoluene, and TAT. The same gradient method at a different column temperature can also be used to baseline separate the explosives targeted in the Environmental Protection Agency (EPA) Method 8330 with approximately 22% reduction in total run time and 48% decrease in solvent consumption compared to previously published methods. Good separation was also obtained when all TNT metabolites and EPA Method 8330 compounds (a total of 23 compounds) were analyzed together; only 2,6-DANT and HMX co-eluted in this case. The influence of temperature (35-55 degrees C) and the use of an ion-pair reagent on the chromatographic resolution and retention were investigated. Temperature was identified as the key parameter for optimal baseline separation. Increased temperature resulted in shorter retention times and better peak resolution especially for the aminoaromatics investigated. The use of an ion-pair reagent (octanesulfonic acid) generally resulted in longer retention times for compounds containing amine functional groups, more baseline noise, and decreased peak resolution.     

Uses of 5-Methylresorcin-bonded polyurethan foam as a new solid phase extractor for the selective separation of mercury ions from natural water samples

In this work, 5-Methylresorcin (MR) bonded to untreated polyurethane foam (PUF) was successfully employed as a sorbent (MR-PUF) for the selective separation and determination of mercury in natural water samples. Mercury can be quantitatively recovered in the pH range of 5-7. The system presented a minicolumn packed with the new sorbent, where the sample solution was passed through it for a period of time and an eluent solution stripped out the retained mercury, which was further determined with dithizone. The new matrix was characterized by using different tools (IR spectra, stability and density). The kinetics of mercury uptake by the new matrix was found to be fast, reaching equilibrium in 20 minutes. A preconcentration factor of 350 was achieved. The proposed preconcentration procedure was applied successfully to the selective separation and determination of trace mercury in natural water samples.      

Solid-phase extraction using molecularly imprinted polymers for selective extraction of a mycotoxin in cereals

The aim of this work was to develop a method for the clean-up of a mycotoxin, i.e. Ochratoxin A (OTA), from cereal extracts employing a new molecularly imprinted polymer (MIP) as selective sorbent for solid-phase extraction (SPE) and to compare with an immunoaffinity column. A first series of experiments was carried out in pure solvents to estimate the potential of the imprinted sorbent in terms of selectivity studying the retention of OTA on the MIP and on a non-imprinted polymer using conventional crushed monolith. The selectivity of the MIP was also checked by its application to wheat extracts. Then, after this feasibility study, two different formats of MIP: crushed monolith and micro-beads were evaluated and compared. Therefore an optimization procedure was applied to the selective extraction from wheat using the MIP beads. The whole procedure was validated by applying it to wheat extract spiked by OTA at different concentration levels and then to a certified contaminated wheat sample. Recoveries close to 100% were obtained. The high selectivity brought by the MIP was compared to the selectivity by an immunoaffinity cartridge for the clean-up of the same wheat sample. The study of capacity of both showed a significant higher capacity of the MIP.     

Sol–gel/nanoclay composite as a sorbent for microextraction in packed syringe combined with corona discharge ionization ion mobility spectrometry for the determination of diazinon in water samples

In this work, the microextraction in packed syringe technique combined with corona discharge ion mobility spectrometry was used for determining diazinon in water samples. A new porous composite of nanoclay and polysiloxane was prepared using a sol–gel process. An amount of 2.0 mg of the sorbent was packed in a 250 μL syringe and used for extraction. A volume of 2 mL of the sample was passed through the sorbent bed, and the entrapped analyte was eluted by 25 μL of methanol. Important parameters influencing the extraction performance were investigated. Under optimum experimental conditions, the detection limit for diazinon was 0.07 ng/mL. The intra‐ and inter‐day relative standard deviations were 5.0 and 12.3%, respectively. The calibration curve was linear in the concentration range from 0.2 to 20.0 ng/mL (r² = 0.999). The applicability of the method was demonstrated by analyzing spiked real water samples and the spiking recoveries were in the range of 95 to 106%.     

Exploiting automatic on-line renewable molecularly imprinted solid-phase extraction in lab-on-valve format as front end to liquid chromatography: application to the determination of riboflavin in foodstuffs

In the present work, it is proposed, for the first time, an on-line automatic renewable molecularly imprinted solid-phase extraction (MISPE) protocol for sample preparation prior to liquid chromatographic analysis. The automatic microscale procedure was based on the bead injection (BI) concept under the lab-on-valve (LOV) format, using a multisyringe burette as propulsion unit for handling solutions and suspensions. A high precision on handling the suspensions containing irregularly shaped molecularly imprinted polymer (MIP) particles was attained, enabling the use of commercial MIP as renewable sorbent. The features of the proposed BI-LOV manifold also allowed a strict control of the different steps within the extraction protocol, which are essential for promoting selective interactions in the cavities of the MIP. By using this on-line method, it was possible to extract and quantify riboflavin from different foodstuff samples in the range between 0.450 and 5.00 mg L⁻¹ after processing 1,000 μL of sample (infant milk, pig liver extract, and energy drink) without any prior treatment. For milk samples, LOD and LOQ values were 0.05 and 0.17 mg L⁻¹, respectively. The method was successfully applied to the analysis of two certified reference materials (NIST 1846 and BCR 487) with high precision (RSD < 5.5%). Considering the downscale and simplification of the sample preparation protocol and the simultaneous performance of extraction and chromatographic assays, a cost-effective and enhanced throughput (six determinations per hour) methodology for determination of riboflavin in foodstuff samples is deployed here.     

Use of cotton as a sorbent for on-line precolumn enrichment of polycyclic aromatic hydrocarbons in waters prior to liquid chromatography determination

Using cotton as a solid-phase extraction sorbent of the precolumn, an on-line coupled precolumn preconcentration-liquid chromatography system with fluorescence detection was developed for the determination of PAHs in aqueous samples. Four PAHs including fluorene, phenanthrene, fluoranthene and benzo[k]fluoranthene were preconcentrated by a precolumn packed with 30 mg of absorbent cotton and then separated by C₁₈ analytical column. When 100 ml of sample was enriched, the proposed procedure provided detection limits in the range of 0.5-57 ng l⁻¹. Several water samples spiked with PAHs were analyzed with recoveries in the range of 92-119% at spiking level of 100 ng l⁻¹ for fluorene, phenanthrene and fluoranthene, and 10 ng l⁻¹ for benzo[k]fluoranthene, respectively.     

Solvating gas chromatography with chemiluminescence detection of nitroglycerine and other explosives

A separation technique known as solvating gas chromatography (SGC), which utilizes packed capillary columns and neat carbon dioxide as mobile phase, was used for the separation of nitroglycerine (NG) and other nitrogen-containing explosives including 2,6-dinitrotoluene (2,6-DNT), 2,4-dinitrotolulene (2,4-DNT), 2,4,6-trinitrotoluene (2,4,6-TNT), and pentaerythritol tetranitrate (PETN). SGC was coupled for the first time to a selective chemiluminescence thermal energy analyzer (TEA) detector for nitro-functional group specificity and sensitive detection of these compounds. TEA calibration curve for NG showed linearity in the sub-microg ml(-1) range. Soil samples containing NG were used to test the validity of the technique. Detector response of SGC-TEA versus SGC-flame ionization detection for NG was also evaluated.     

Hierarchically imprinted organic-inorganic hybrid sorbent for selective separation of mercury ion from aqueous solution

A new type of hierarchically organic-inorganic hybrid sorbent was prepared by a double-imprinting approach for the selective separation of Hg(II) from aqueous solution. In the imprinting process, both mercury ions and surfactant micelles (cetyltrimethylammonium bromide, CTAB) were used as templates, N-[3-(trimethoxy-silyl)propyl]ethylenediamine (TPED) as functional monomer, and tetraethoxysilane (TEOS) as cross-linking agent. The mercury ions and surfactant were removed from sorbent via acid leaching and ethanol extraction, respectively. The adsorption property and selective recognition ability of the sorbents were studied by equilibrium-adsorption method. Results showed that in the presence of Cu(II) or Cd(II) the biggest selectivity coefficient of the imprinted sorbents for Hg(II) was over 100, which is much higher than those of non-imprinted sorbents. The largest relative selectivity coefficient (k′) of the ion-imprinted functionalized sorbent between Hg(II) and Cu(II) was over 300, and between Hg(II) and Cd(II) over 200. The uptake capacities and the selectivity coefficients of the hierarchically imprinted sorbent were much higher than those of the sorbent prepared without CTAB template. Furthermore, the new imprinted sorbent possessed a fast kinetics for the removal of Hg(II) from aqueous solution with the saturation time less than 5 min, and could be used repeatedly. This sorbent has been successfully applied to the separation and determination of the trace Hg(II) in real water samples and those spiked with standards. This new sorbent can be used as an effective solid-phase extraction material for the selective preconcentration and separation of Hg(II) in environmental samples.     

A new and fast strategy based on semiautomatic microextraction by packed sorbent followed by ultra high performance liquid chromatography for the analysis of drugs and their metabolites in human urine

A novel analytical approach has been developed for the determination of selected drugs (milrinone, enalapril, carvedilol, spironolactone, acenocumarol, ticlopidine, cilazapril) and their metabolites (2‐oxoticlopidine, cilazaprilat, canrenone, 5′‐hydroxycarvedilol, O‐desmethyl‐carvedilol, enalaprilat) in human urine, based on a miniaturized extraction technique; semiautomatic microextraction by packed sorbent, using a new digitally controlled syringe, followed by ultra high pressure liquid chromatography separation combined with UV detection. During method optimization, the extraction parameters as the type of sorbent material, type and volume of elution solution, number of extraction cycles, volume and pH of sample, type and volume of washing solution were studied. The chromatographic separation of the target analytes was performed with a core–shell analytical column using 0.05% trifluoroacetic acid in water and acetonitrile in gradient elution mode. The limits of quantification ranged from 0.016 to 0.045 μg/mL. Under the optimized conditions, extraction efficiency was higher than 70.1% for drugs and their metabolites. Due to its simplicity and speed, this method was successfully applied to the quantitation of selected compounds in urine samples.     

Selective extraction and release using (EDTA-Ni)-layered double hydroxide coupled with catalytic oxidation of 3,3′,5,5′-tetramethylbenzidine for sensitive detection of copper ion

Copper is an important heavy metal in various biological processes. Many methods have been developed for detecting of copper ions (Cu²⁺) in aqueous samples. However, an easy, cheap, selective and sensitive method is still desired. In this study, a selective extraction-release-catalysis approach has been developed for sensitive detection of copper ion. Ethylenediaminetetraacetic acid (EDTA) chelated with nickel ion (Ni²⁺) were intercalated in a layered double hydroxide via a co-precipitation reaction. The product was subsequently applied as sorbent in dispersive solid-phase extraction for the enrichment of Cu²⁺ at pH 6. Since Cu²⁺ has a stronger complex formation constant with EDTA, Ni²⁺ exchanged with Cu²⁺ selectively. The resulting sorbent containing Cu²⁺ was transferred to catalyze the 3,3′,5,5′-tetramethylbenzidine oxidation reaction, since Cu²⁺ could be released by the sorbent effectively and has high catalytic ability for the reaction. Blue light emitted from the oxidation product was measured by ultraviolet–visible spectrophotometry for the determination of Cu²⁺. The extraction temperature, extraction time, and catalysis time were optimized. The results showed that this method provided a low limit of detection of 10 nM, a wide linear range (0.05–100 μM) and good linearity (r² = 0.9977). The optimized conditions were applied to environmental water samples. Using Cu²⁺ as an example, this work provided a new and interesting approach for the convenient and efficient detection of metal cations in aqueous samples.     

Aptamer-targeted magnetic nanospheres as a solid-phase extraction sorbent for determination of ochratoxin A in food samples

A sorbent based on the aptamer for ochratoxin A was immobilized onto magnetic nanospheres (MNS) and used to develop a magnetic solid-phase extraction procedure to clean up food samples in conjunction with high-performance liquid chromatography separation and fluorescence detection. Specific retention of ochratoxin A by the sorbent was demonstrated, and the capacity of the MNS-aptamer sorbent was determined. The efficacy of this new approach was successfully evaluated through comparison with solid-phase extraction on commercial C18 cartridge. Several different food samples fortified in the range of with 2.5-50 μg/kg yielded mean recoveries from 67% to 90%, respectively. Finally, this oligosorbent was applied to the selective extraction of ochratoxin A from unfortified food samples.     

Preparation and evaluation of an ion imprinted sol–gel material for selective solid-phase extraction of Ni(II)

An ion imprinted silica sorbent was prepared using a sol–gel process for selective extraction of Ni(II) ions from water samples. Bis(dibenzoylmethanto)nickel(II) complex was used as template; phenyltrimethoxysilane and 3-aminopropyltriethoxysilane as functional monomers and tetraethylorthosilicate as reticulating agent. The material was packed in solid-phase extraction (SPE) column. The effect of sampling volume, elution conditions, sample pH and sample flow rate on the extraction of Ni ions from water samples were studied. The relative selectivity coefficients of imprinted sorbent for Ni(II)/Co(II), Ni(II)/Cu(II) and Ni(II)/Cd(II) were 23.7, 30.3 and 24.4, times greater than non-imprinted sorbent, respectively. The relative standard deviation of the eight replicate determinations of Ni(II) was 4.2%. The detection limit was 0.9 µg L^?1 using flame atomic absorption spectrometry. The developed method was successfully applied to the determination of trace nickel in water samples.