Adsorption of chlorhexidine onto cellulosic fibers

Comparative investigations of adsorption properties of chlorhexidine (CHX) on two cellulose fibers, bleached cotton and viscose, were studied in order to obtain dry gauzes covered with known amount of this antiseptic. Adsorption isotherm results carried out at 293 and 323 K can be described by Langmuir isotherm model, nevertheless, at high concentration correlation is better to Freundlich isotherm. Electrokinetic potential evolution with CHX concentration, shows that initial negative zeta potential of cotton and viscose diminish its absolute value as the concentration of the treatment increases; both fibers present an isoelectric point at high concentration of CHX that is 0.3 mM for viscose and 0.8 mM for cotton. Electrostatic interactions between cationic groups of CHX and carboxylic acid groups of the fibers could explain adsorption at low concentration, but when it is higher than these values, possible hydrogen bonding between the amine groups of CHX and hydroxyl groups of cellulose could explain increasing adsorption when it is hindered by electrostatic repulsion as it is predicted by Freundlich model, that describes heterogeneous surface and multilayer adsorption. Adsorption kinetics isotherms reveal that the process is quick with t _1/2 values of 5.4 min for cotton and 2.8 min for viscose. Differences in adsorption behaviour between the two fibers could be attributed to structural differences as we have observed from estimation of CI index based on FTIR spectra. Values obtained 1.6 for viscose and 2.2 for cotton could explain that the amount of CHX adsorbed on viscose is higher than it is on cotton. Finally desorption experiments performed with 0.01 M of NaCl solution at room temperature and pH 6 reveals the possibility of therapeutical application of these fibers although further investigations must be done to optimize the process.     

Adsorption of organic compounds onto polyelectrolyte immobilized-surfactant aggregates on cellulosic fibers

The adsorption of anionic surfactants with different hydrophobic chain lengths onto cellulose fibers pretreated with a cationic polyelectrolyte has been investigated. Five steps are involved in the adsorption process, which was ascribed to the formation of monolayer and bilayer surfactant aggregates. Electrostatic interaction between the residual surface charges followed by hydrophobic interaction among the alkyl chains are considered the main factors in the adsorption process. The adsorption of the anionic surfactant was found to greatly enhance the retention of organic compounds onto the polyelectrolyte-treated cellulose. The coadsorption phenomenon, which was dependent on the saturation level of the adsorbed surfactant, has been explained in terms of the accumulation of the organic solute on the hydrophobic core generated by the adsorbed layer.     

The adsorption behavior of cationic surfactant onto human hair fibers

Quaternary ammonium surfactants are important ingredients that are frequently formulated into hair care products to modify the properties of hair surface. The adsorption kinetics, isotherms and association structures of cationic surfactants on hair surface, however, are not fully understood due to the heterogeneous nature of human hair fibers. In this work, a quaternary ammonium of surfactant, dimethylpabamidopropyl laurdimonium tosylate (DDABDT) was chosen as a probe to investigate the adsorption behavior of cationic surfactant on cuticles of scalp hair. The results reveal that the adsorption kinetics fit to a pseudo-second-order kinetic model and the adsorption isotherms fit to the Freundlich adsorption model. With the increase of DDABDT adsorption, the wettability of hair fibers changes from hydrophobic to hydrophilic. The association structure could be monolayer or bilayer depending on the initial concentration of the surfactant. In the monolayer structure, the ‘anchor’ surfactant molecules are believed to adsorb vertically on the surface of hair fibers through electrostatic interaction. In the bilayer structure, the second layer molecules may then pile up on top of the first layer with charged groups orienting outward. The thickness of DDABDT film on hair fibers treated with 5 × 10^?4 mol/l DDABDT solution is measured to be 5.42 nm on average with a force–distance method. This figure is very close to the two times of the theoretical molecular size of the DDABDT molecule.     

Adsorption of a new amphoteric cellulosic copolymer onto bentonite

The adsorption of a new amphoteric cellulosic copolymer onto bentonite from aqueous solutions was studied at different salt concentrations and temperatures. The adsorption kinetics included a fast step and a slow step. The rate of initial rapid adsorption was reduced by the addition of NaCl. An increase in the concentration of added NaCl or increasing temperature decreased the amounts adsorbed. The influence of sodium dodecylsulfate and hexadecyl trimethylammonium chloride was also studied. Received: 14 December 1998 Accepted in revised form: 3 February 1999     

Diffusion of cationic polyelectrolytes into cellulosic fibers

The penetration of cationic polyelectrolytes into anionic cellulosic fibers was evaluated with fluorescent imaging techniques in order to clarify the mechanism and time scales for the diffusion process. The bulk charge of the cellulosic fibers indirectly creates a driving force for diffusion into the porous fiber wall, which is entropic in nature due to a release of counterions as the polyelectrolyte adsorbs. The individual bulk charges in the fiber cell wall also interact with the diffusing polyelectrolyte, such that the polyelectrolyte diffuses to the first available charge and consequently adsorbs and remains fixed. Thus, subsequent polyelectrolyte chains must first diffuse through the adsorbed polyelectrolyte layer before adsorbing to the next available bulk charges. This behavior differs from earlier suggested diffusion mechanisms, by which polyelectrolytes were assumed to first adsorb to the outermost surface and then reptate into the pore structure. The time scales for polyelectrolyte diffusion were highly dependent on the flexibility of the chain, which was estimated from calculations of the persistence length. The persistence length ultimately depended on the charge density and electrolyte concentration. The charge density of the polyelectrolyte had a greater influence on the time scales for diffusion. High charge density polyelectrolytes were observed to diffuse on a time scale of months, whereas the diffusion of low charge density polyelectrolytes was measured on the order of hours. An influence of the chain length, that is, steric interactions due the persistence length of the polyelectrolyte and to the tortuosity of the porous structure of the fiber wall, could only be noted for low charge density polyelectrolytes. Increasing the electrolyte concentration increased the chain flexibility by screening the electrostatic contribution to the persistence length, in turn inducing a faster diffusion process. However, a significant change in the diffusion behavior was observed at high electrolyte concentrations, at which the interaction between the polyelectrolyte charges and the fiber charges was almost completely screened.     

Adsorption of cationic surfactants and subsequent adsolubilization of organic compounds onto cellulose fibers

Cationic surfactants with different hydrophobic chain length were adsorbed onto cellulose fibers in an aqueous medium. The adsorption isotherms exhibited three characteristic regions which were interpreted in terms of the mode of aggregation of the surfactant molecules at the solid–liquid interface. The hydrophobic layers were used as a reservoir to trap various slightly water soluble organic molecules. A quantitative study of these phenomena suggested typical partition behavior of the organic solutes between the aqueous phase and the surfactant layer. The surfactant chain length (from C12 to C18) was shown to play an important role in terms of the capacity to retain the organic solute and the capacity increased with the number of carbon atoms.     

Adsorption of a cationic porphyrin onto mesoporous silicas

The adsorption of a cationic porphyrin, tetrakis-(N-methyl-4-pyridiniumyl)porphine, into mesoporous silicas from solution of tetrakis-(N-methyl-4-pyridiniumyl)porphine p-toluene sulfonate was investigated. Irrespective of the pore size (2.4, 3.5 and 4.2 nm), the cationic porphyrin was adsorbed effectively onto mesoporous silicas to give brown-colored powders. Depending on the amounts adsorbed, which correlate with the average intermolecular distance, the porphines tend to aggregate (dimer).     

Adsorption of cationic cellulose derivative/anionic surfactant complexes onto solid surfaces. II. Hydrophobized silica surfaces

The effect of the anionic surfactant SDS (sodium dodecyl sulfate) on the adsorption behavior of cationic hydroxyethyl cellulose (Polymer JR-400) and hydrophobically modified cationic cellulose (Quatrisoft LM-200) at hydrophobized silica has been investigated by null ellipsometry and compared with the previous data for adsorption onto hydrophilic silica surfaces. The adsorbed amount of LM-200 is found to be considerably larger than the adsorbed amount of JR-400 at both surfaces. Both polymers had higher affinity toward hydrophobized silica than to silica. The effect of SDS on polymer adsorption was studied under two different conditions: adsorption of polymer/SDS complexes from premixed solutions and addition of SDS to preadsorbed polymer layers. Association of the surfactant to the polymer seems to control the interfacial behavior, which depends on the surfactant concentration. For the JR-400/SDS complex, the adsorbed amount on hydrophobized silica started to increase progressively from much lower SDS concentrations, while the adsorbed amount on silica increased sharply only slightly below the phase separation region. For the LM-200/SDS complex, the adsorbed amounts increased progressively from very low SDS concentrations at both surfaces, and no large difference in the adsorption behavior was observed between two surfaces below the phase separation region. The complex desorbed from the surface at high SDS concentrations above the critical micelle concentration. The reversibility of the adsorption of polymer/SDS complexes upon rinsing was also investigated. When the premixed polymer/SDS solutions at high SDS concentrations (>5 mM) were diluted by adding water, the adsorbed amount increased due to the precipitation of the complex. The effect of the rinsing process on the adsorbed layer was determined by the hydrophobicity of the polymer and the surface.     

Grafting of acrylamide onto cellulosic fibers via dielectric-barrier discharge

Fully bleached kraft pulp (BKP) and thermomechanical pulp (TMP) fibers were grafted with acrylamide via dielectric-barrier discharge treatment at various treatment dosages. The results indicate that increased dielectric-barrier discharge treatment leads to the increased polymerization and incorporation of acrylamide onto fiber surfaces. Greater incorporation of poly(acrylamide) occurs on the BKP fibers than the TMP at the same treatment conditions. Time-of-flight secondary ion mass spectrometry (ToF-SIMS) and scanning electron microscopy (SEM) indicate that dielectric-barrier discharge initiated modifications to fiber surface topo-chemistry occur across the fiber such that the sheet is randomly peppered with modified areas; however, it occurs in patches on individual fibers as opposed to occurring as an evenly distributed thin film. SEM and elemental analysis also showed that the incorporation of acrylamide onto the fiber surface increases with increased treatment dosages.     

Surface complexation of DNA with a cationic surfactant

We have studied the surface complexation of DNA with a cationic surfactant (DTAB) using a combination of methods: dynamic surface tension, ellipsometry and Brewster angle microscopy. Below the surfactant critical aggregation concentration (cac), complexation occurs only at the surface, and the results are consistent with neutralization of the surfactant charges by the free polymer ions. Above the cac, surfactant starts to bind cooperatively to DNA in the bulk, and adsorption of the preformed hydrophobic surfactant DNA aggregate is now possible, leading to thick surface layers. At still higher concentrations of surfactant (still below saturation of binding in the bulk), there is decrease in adsorption due to competition with bulk aggregates. Finally, as surfactant concentration is increased still further, bulk aggregates become less soluble and large amounts are adsorbed, forming a surface layer, which is solid-like and brittle.     

Analysis of CMC attachment onto cellulosic fibers by infrared spectroscopy

Infrared spectroscopy has been used to measure the amount of carboxymethyl cellulose (CMC) attached to cellulosic fibers. CMC was attached to an unbleached kraft pulp in aqueous conditions. Isotropic handsheets were then prepared and ATR spectroscopy was used to measure the intensity of the carboxyl vibration, which correlates to the amount of attached CMC that was determined using a wet chemical approach. The ATR method is rather time consuming as several measurement points on the sample have to be averaged, although it is still much faster than the wet chemical approach. Infrared reflection absorption spectroscopy (IRRAS) using polarized light was further used to measure the amount of attached CMC. In this method the intensity of an electromagnetic wave confined to the thin layer is used to correlate the spectroscopy to the amount of CMC on the fiber surface in the paper sample. The measurement time is shorter than with the ATR method. The proposed IRRAS method could be employed as a fast and reliable way to quantify adsorption of chemicals on pulp fibers.     

Adsorption of octadecyltrimethylammonium chloride and adsolubilization on to cellulosic fibers

The coadsorption of different organic solutes on cellulosic fibers treated with octadecyltrimethylammonium chloride (ODTMA) has been studied. In the absence of ODTMA cellulosic fibers had little tendency to retain organic compounds. The enhanced solute incorporation was ascribed to the adsolubilization of these compounds on the aggregated domains of the adsorbed surfactant molecules at the solid/liquid interface. The specific shape of solute coadsorption isotherms indicated that the adsolubilization process may be regarded as a partition phenomenon between the aqueous bulk phase and the adsorbed surfactant aggregates. The decrease in solute uptake at the cellulose/water interface above the CMC of ODTMA was ascribed to micelle formation in the bulk solution and to the ensuing micellar solubilization of organic solutes. Preliminary experiments performed using vertical fixed bed columns showed that modified cellulosic fibers can be conveniently used as substrate for treating organic pollutants.     

Birefringence of native cellulosic fibers. I. Untreated cotton and ramie

The Rayleigh-Gans theory of light scattering by a homogeneous cylinder has been applied to the case of scattering by a pad of fibers immersed in a liquid. The theory enables one to locate precisely the matching wavelength at which the mean refractive index of a sample of optically heterogeneous fibers coincides with that of an immersion medium. Thereby it offers a method of determining the mean refractive index. Besides, it facilitates a quantitative estimation of the variability of refractive index. The new technique has been used to study the birefringence of untreated cotton and ramie. The results are presented and discussed.     

烟酸在铁钝化膜层表面的吸附机理

循环伏安法结合原位拉曼光谱的表征结果表明,烟酸在铁钝化膜层表面的吸附行为归因于其具有形成稳定膜层复合物的性能,烟酸将间隙离子FeⅡ转化为稳定的晶格离子FeⅢ,从而降低铁钝化膜的溶解性.旋转电极电化学晶体微天平的分析结果表明烟酸在活化态和钝化态铁表面的吸附行为遵循LangmuirFreundlich热力学规律,并由此计算出过程中的吸附常数、标准自由能和非均质分布常数.研究认为有机分子在钝化膜表面为化学型吸附,可导致钝化膜破坏的间隙离子被烟酸固定在八面体空位晶格中形成稳定晶型结构,并通过扫描电镜(SEM)和衰减全反射红外光谱(ATR FTIR)分析对结论进行了再次验证.     

尿素在ZnO(1010)表面的吸附

运用VASP(Vienna ab-initio simulation package),采用基于密度泛函理论(DFT)的第一原理计算,研究了尿素在ZnO(101軈0)表面的吸附行为.计算结果表明:尿素分子在ZnO(101軈0)表面主要发生分子吸附,稳定的吸附产物通过尿素分子中的氮原子或氧原子与表面锌原子之间的键合作用而形成,吸附能分别为-1.48和-1.41eV;表面吸附的尿素分子也可以发生解离,生成表面吸附的异氰酸根、氨气和一个表面羟基,吸附能为-1.66eV.     

Adsorption of phenol and benzyl alcohol onto surfactant modified silica

The adsorption of the surfactant, dodecyltrimethylammonium bromide, DTAB, and the co-adsorption of the additives phenol and benzyl alcohol, onto silica from aqueous solutions are investigated. The adsorption of DTAB is found to increase with increasing alcohol concentration in solutions where the DTAB concentration is below the cmc. Moreover, the corresponding adsorption of DTAB decreases when the DTAB concentration is above the cmc. The co-adsorption of the alcohol is found to increase with increasing alcohol concentration, and benzyl alcohol co-adsorbs more strongly than phenol. The surfactant modified silica shows a very high ability to incorporate phenol and benzyl alcohol. The results are discussed in relation to solubilization site and surfactant aggregate shape.     

蛋白质在羟基磷灰石界面吸附的研究

考察了酪蛋白酸钠(sodium caseinate,SC)和乳清分离蛋白(whey protein isolate,WPI)在表面性质不同的3种羟基磷灰石(hydroxyapatite,HA)颗粒上的界面吸附,分析了蛋白质的分子构型和HA颗粒的表面性质等因素对蛋白质在HA界面吸附的影响,重点讨论了SC和WPI肽链上磷酸化丝氨酸基团(phosphorylated serine residues,Ser-P)的数量和分布对吸附差异的影响.通过傅里叶变换红外光谱和表面电位分析发现SC和WPI无法被比表面积较小的HA颗粒有效吸附,但是在有效吸附面积较高的球状纳米HA和棒状微米HA上能够被吸附.Ser-P的存在使得SC在HA界面的吸附量更高、吸附能力更强.Ser-P数量和分布的不同则导致了SC中不同的蛋白组分在HA界面的竞争性吸附:β-酪蛋白在2μmHA界面始终存在优先吸附性;当纳米HA的浓度低于15 mg/mL时,纳米HA界面会优先吸附αs-酪蛋白.     

Surface properties of mixed anionic/cationic surfactant solutions

Summary Published experimental surface pressures for mixtures of anionic and cationic surfactants are compared to what can be predicted from the surface behaviour of the separate constituents. Simple theory correctly predicts, for soluble surfactants, a large increase of surface pressure upon mixing an anionic and a cationic solution having the same surface pressure, and, for insoluble surfactants, a decrease of surface pressure upon mixing at a given area per long chain ion. These effects are due to the different adsorption characteristics of the four electroneutral combinations involved, and will occur even in the absence of specific surface interactions.

---

Zusammenfassung Es wurden bekannte Oberflächendrucke für Mischfilme von Aniontensiden und Kationtensiden mit theoretischen Voraussagen, begründet auf dem Grenzflächenverhalten der einzelnen Komponenten, verglichen. Die einfache Theorie sagt richtig voraus, daß die Mischung zweier wäßriger Lösungen von Aniontensid bzw. Kationtensid mit gleichem Oberflächendruck, eine starke Erhöhung des Oberflächendruckes zur Folge haben muß, während die Mischung zweier unlöslicher Filme bei gegebener Tensidadsorption den Oberflächendruck herabsetzt. Dieses Verhalten wird aufgrund der verschiedenen Adsorptionseigenschaften der vier betreffenden Salze gedeutet, und ist von spezifischen Oberflächenwechselwirkungen unabhängig.

     

Adsorption of cationic polyelectrolyte onto a model carboxylic latex and the influence of adsorbed polycation on the charge regulation at the latex surface

 Adsorption of a well-characterized cationic polyacrylamide (CPAM) onto the surface of a model colloid (monodisperse polystyrene latex with carboxylic functional groups) was studied over a wide range of pH (4–9) and KCl concentration (c _s =10^-3–0.3 M). The surface charge density of the latex particles with and without adsorbed CPAM was also measured over the same range of electrolyte compositions. The adsorbed amount of CPAM increases with increase in c _s and pH. The polyelectrolyte adsorption alters substantially the surface charge density of the latex particles as compared to the polymer-free case. A large overcompensation of the surface charge by the adsorbed polyelectrolyte is established at high c _s and low pH. A qualitative explanation of the observed features is put forward. Received: 3 December 1996 Accepted: 20 January 1997     

Spontaneous aggregate transition in mixtures of a cationic gemini surfactant with a double-chain cationic surfactant

Controllable aggregate transitions were realized by mixing two kinds of cationic surfactants, hexylene-1,6-bis(dodecyldimethylammonium bromide) (C(12)C(6)C(12)Br(2)) and didodecyldimethylammonium bromide (DDAB). It was found that two parameters are the main factors determining the aggregation behavior of the mixed system, the total concentration of DDAB and C(12)C(6)C(12)Br(2) (C(T)), and the mole fraction of DDAB in the mixtures of DDAB and C(12)C(6)C(12)Br(2) (X(DDAB)). How these two parameters act on the aggregate transitions was studied in detail by various measurements including surface tension, turbidity, electrical conductivity, ζ potential, isothermal titration microcalorimetry, dynamic light scattering, cryogenic transmission electron microscopy, and (1)H NMR. When C(T) was constant, spontaneous vesicle-to-micelle transitions were found with decreasing X(DDAB) at high C(T). When X(DDAB) was constant, aggregate transitions were generated by gradually increasing C(T), depending on different X(DDAB) ranges. At X(DDAB) < 0.6, small spherical aggregates formed first and then transferred to vesicles, and finally the vesicles transitioned to micelles. At X(DDAB) ≥ 0.6, the progressive increase in C(T) led to aggregate transitions on the order of the arising of vesicles, the continuous growth of vesicles, the disruption of vesicles into micelles, and the final coexistence of vesicles and micelles. The hydrophobic interaction and electrostatic repulsion between DDAB and C(12)C(6)C(12)Br(2) together with the related degree of ionization and hydration of the surfactants were gradually adjusted by changing the ratio and the total concentration of these two surfactants, which should be responsible for the complicated aggregation behavior.