An optically stimulated luminescence study of porcelain related to radiation dosimetry

This article describes the essential features regarding the photo-stimulated luminescence of porcelain: both the main ceramic and glazing materials are studied. In each case, radiation dose dependent signals are observed, superimposed on dose independent luminescence transitions that are both Stokes and anti-Stokes shifted in energy. Glazing is shown in some cases to be considerably more sensitive as a radiation dosemeter than the main porcelain ceramic. By comparison with the properties of artificial phosphors, the principal luminescent matrix is identified as being Al₂O₃, and the recombination centres in one glazing type are shown to be F-centres, Cr³⁺ and Dy³⁺.     

An optically stimulated luminescence study of flint related to radiation dosimetry

This article describes the essential features of photo-stimulated luminescence in flint. The emission is shown to be complex, arising from a number of different aspectsof the material. Under constant illumination, dose-dependent time-decaying anti-Stokes signals are superimposed on dose-independent, time-stable emission that is both Stokes and anti-Stokes shifted in energy. It is argued that the dose-dependent signals arise from the crystalline quartz phase of the material, whereas the dose independent signals originate from an amorphous-like phase of SiO₂. The microcrystallinity of the material leads to contrasting behaviour when compared with bulk crystalline quartz.     

Thermally and optically stimulated luminescence of glass mosaic tesserae

A series of experiments on the luminescence signals from the glassy matrix of mosaic tesserae has been conducted. The results presented show the relationship between the 280–390 °C thermoluminescence (TL) peak and the optically stimulated luminescence (OSL) emitted under illumination by 450 nm light. We have proposed an appropriate laboratory protocol with repeated irradiations and illuminations of the same aliquot of the sample that allowed for establishing a correlation between TSL and OSL emissions, both very likely associated to the same trap. PACS 78.66.Jg; 87.66.Sq; 78.60.Kn     

Thermo-optical properties of optically stimulated luminescence in feldspars

Optically stimulated luminescence processes in feldspars are subject to competing thermal enhancement and quenching processes: this article describes the thermal enhancement effects for orthoclase, albite and plagioclase feldspars. It is demonstrated that certain lattice vibrational modes can be selectively probed at specific optical excitation energies. The results are described in terms of the Bohr hydrogen model of the OSL donor defects.     

A study on the real-time radiation dosimetry measurement system based on optically stimulated luminescence

The optically stimulated luminescent (OSL) radiation dosimeter technically surveys a wide dynamic measurement range and a high sensitivity.Optical fiber dosimeters provide capability for remote monitoring of the radiation in the locations which are difficult-to-acoess and hazardous.In addition.optical fiber dosimeters are immune to electrical and radio-frequency interference.In this paper,a novel remote optical fiber radiation dosimeter is described.The optical fiber dosimeter takes advantage of the charge trapping materials CaS:Ce, Sm that exhibit OSL.The measuring range of the dosimeter is from 0.1 to 100 Gy.The equipment is relatively simple and small in size,and has low power consumption.This device is suitable for measuring the space radiation dose and also can be used in high radiation dose condition and other dangerous radiation occasions.     

On some fundamental features of optically stimulated luminescence measurements

The influence of electron–phonon interaction on the shape of the optically stimulated luminescence decay curve has been examined. The formula describing the dependence of optical cross-section on stimulation energy and temperature has been applied in a computer simulation of optically stimulated luminescence process. Computer simulations have been carried out for different temperatures using both one-trap and two-trap models. The ideas of an OSL measurement with continuously increasing energy of stimulation have been tested via computer simulations. The outcomes of this technique have been presented for a wide range of material parameters.     

α-Al2O3:C晶体的热释光和光释光特性

以高纯α-Al2O3和石墨为原料,采用温梯法生长了α-Al2O3:C晶体,使用Ris TL/OSL-DA-15型热释光和光释光仪研究了其热释光和光释光特性.α-Al2O3:C晶体在462 K附近有单一热释光峰,发射波长位于410 nm.随着辐照剂量的增加,热释光强度逐渐增强,462 K的热释光特征峰位置保持不变.α-Al2O3:C晶体的光释光衰减曲线由快衰减和慢衰减两个部分组成,随着辐照剂量的增加,快衰减部分衰减速率变化不大,而慢衰减部分衰减速率加快.在5×10-6-10 Gy剂量范围内,α-Al2O3:C晶体的热释光剂量响应呈现良好的线性关系,30 Gy时达到饱和;光释光剂量响应在5×10-6-60 Gy剂量范围内呈现良好的线性关系,100 Gy时达到饱和.与热释光相比,光释光剂量响应具有更高的灵敏度和更宽的线性剂量响应范围.     

Dose-dependent optically stimulated luminescence of synthetic quartz at room temperature

Physical conditions such as annealing temperature, duration of annealing, ionizing radiation, etc., play a significant role in the applications of optically stimulated luminescence (OSL) dating as well as OSL dosimetry. Many efforts are made to understand the effect of these physical parameters on quartz specimens owing to its use in such applications. Such factors induce changes in OSL decay pattern. The definite correlation between color centers and luminescence sensitivity can be established on account of such pre-treatments to the specimen.The purpose of present investigations is to study the effect of ionizing radiation under identical physical conditions on OSL properties measured at room temperature. The shapes of decay curve and dose-response data are considered for this purpose. This study can reveal the changes in color centers in response to the pre-conditions to the specimen. It was found that the OSL decay remains slow and OSL properties change systematically with the rise in beta dose up to a critical dose; however, it changes the pattern when the beta exposure to the specimen was increased higher than the critical dose. This critical dose was found to be different for different temperature of annealing. The shape of decay curve up to the critical dose was also studied by considering the difference of OSL intensities between two successive durations from the observed OSL decay data. The results are explained based on the changes in available shallow traps during OSL measurement at room temperature with changes in pre-conditions to the specimens. The results also have been confirmed with the corresponding changes in ESR signals.     

Cross-talk during single grain optically stimulated luminescence measurements of quartz and feldspar

Focussed laser systems designed to measure the optically stimulated luminescence (OSL) signals from individual sand sized mineral grains are now widely used. One system that is commonly used can hold up to 100 grains on a 9.8 mm diameter aluminium disc, and can use either a green or infrared (IR) laser for optical stimulation. The grains are held in holes drilled into the disc surface, and the spacing between the edges of adjacent holes is only 300 μm. Focussing of the laser is essential to prevent inadvertent optical stimulation of adjacent grains, but no measurements have previously been made to determine the extent of cross-talk. Measurements on two systems show that the maximum cross-talk for an adjacent position is 0.22%, but typically the value is 0.04% for the green laser and 0.08% for the IR laser. This magnitude of cross-talk is unlikely to have a significant impact on continuous wave OSL measurements where the period of optical stimulation tends to be short, but may be important in linearly modulated OSL measurements where long periods of stimulation are sometimes used to characterise slow components of the OSL signal.     

Luminescence properties of BeO optically stimulated luminescence (OSL) detectors

The objective of this work is to investigate basic luminescence properties of BeO optically stimulated luminescence (OSL) detectors, including the OSL emission and stimulation spectrum, the lifetime of the luminescence centers contributing to the OSL signal, and the temperature dependence of the luminescence lifetime and of the luminescence efficiency. The OSL stimulation spectrum shows a continuous increase in OSL intensity with decreasing stimulation wavelength. The emission spectrum indicates two OSL emission bands at ～310 nm and ～370 nm, the latter being the dominant OSL emission band. We also observed that the luminescence centers associated with the OSL signal are strongly quenched above room temperature, resulting in a reduction in luminescence lifetime from ～27 μs at room temperature down to ～800 ns at 140 °C. The activation energy for non-radiative decay of the luminescence center was determined to be E = (0.568 ± 0.023) eV. The ～27 μs luminescence lifetime observed for BeO indicate that POSL technique may be used to improve the signal-to-noise ratio using stimulation pulses of the order of microseconds. The information obtained in this study may help further optimize the BeO dosimetry systems and provide guidance on the timing parameters to be used for POSL measurements of this material.     

Dose dependence of thermally transferred optically stimulated luminescence signals in quartz

The thermally transferred optically stimulated luminescence (TT-OSL) responses of chemically purified fine-grained quartz from seven loess-like samples from Korea are presented. In particular, the experimental procedures used to separate the dose-dependent (recuperated OSL, ReOSL) and dose-independent parts of the signal were explored. The OSL signals used to monitor the sensitivity changes that take place during the measurement sequences used to determine the equivalent dose were investigated. A single aliquot procedure was used for the TT-OSL measurements and resulted in linear growth of the ReOSL with dose up to at least 2 kGy. For this suite of samples, a standardised growth curve (SGC) was constructed for the ReOSL, tested with dose recovery experiments, and was used to obtain D_e values for the seven samples.     

Development of a new curve deconvolution algorithm for optically stimulated luminescence

A new computerized glow curve deconvolution (CGCD) algorithm for thermoluminescence(TL) and optically stimulated luminescence (OSL) is presented. The proposed approach can be adopted in a numerical curve fitting for obtaining the relevant trapping parameters of a set of glow data taken with both thermal and optical stimulation. This method is based on the one trap one recombination center (OTOR) model with minimal simplifying assumptions. To demonstrate the ability of the method, a new computer program has been developed and tested with some synthetic OSL data.     

Radiation dose response correlation between thermoluminescence and optically stimulated luminescence in quartz

The fast, linearly modulated optically stimulated luminescence (LM-OSL) component in quartz is the main dosimetric signal used for the dating applications of this material. Since the blue light stimulation (470 nm, 40 mW cm ${}^{?2}$) time needed to obtain the fast LM-OSL component is less than 50 s the electron trapping levels responsible for it are still highly populated. In this way an active radiation history is created which could play an important role in the dosimetric characteristics of the fast OSL signal. In the present work the dose response behavior of the fast OSL signal is investigated in quartz samples with an annealed radiation history and quartz samples possessing an artificial radiation history. A computerized curve de-convolution analysis of the LM-OSL curves for 50 s stimulation time showed that it consists of three individual OSL components. The faster component C₁ with peak maximum time around 5 s has a linear dose response in virgin samples, which turns to a slight superlinearity as a function of the artificial radiation history. On the other hand the component C₂ with peak maximum time at 12 s is slightly superlinear which turns into strong superlinearity as a function of artificial radiation history. Finally, component C₃ with peak maximum time at about 45 s is strongly superlinear for both virgin samples and as a function of artificial radiation history. The implications to practical application are discussed.     

Modelling the thermal quenching mechanism in quartz based on time-resolved optically stimulated luminescence

This paper presents a new numerical model for thermal quenching in quartz, based on the previously suggested Mott-Seitz mechanism. In the model electrons from a dosimetric trap are raised by optical or thermal stimulation into the conduction band, followed by an electronic transition from the conduction band into an excited state of the recombination center. Subsequently electrons in this excited state undergo either a direct radiative transition into a recombination center, or a competing thermally assisted non-radiative process into the ground state of the recombination center. As the temperature of the sample is increased, more electrons are removed from the excited state via the non-radiative pathway. This reduction in the number of available electrons leads to both a decrease of the intensity of the luminescence signal and to a simultaneous decrease of the luminescence lifetime. Several simulations are carried out of time-resolved optically stimulated luminescence (TR-OSL) experiments, in which the temperature dependence of luminescence lifetimes in quartz is studied as a function of the stimulation temperature. Good quantitative agreement is found between the simulation results and new experimental data obtained using a single-aliquot procedure on a sedimentary quartz sample.     

A time-correlated photon counting system for measurement of pulsed optically stimulated luminescence

A versatile light-emitting-diode system for measurement of time-resolved luminescence spectra is described. The instrument is an improvement on a previously reported version [1] also based on pulsed light-emitting diodes. The present configuration offers substantially improved performance in measurement of time-resolved optically stimulated luminescence spectra and records the luminescence with better dynamic throughput. Measurements made on sedimentary quartz annealed at 800 °C as an exemplar show that the luminescence obtained after the light pulse as a proportion of the total measured signal falls within the usable dynamic range of 0.1-98% for pulse-widths between 3 and , a range of pulse-widths and so luminescence yield that is sufficient for most contemporary applications of time-resolved optically stimulated luminescence.     

Al2O3:C optically stimulated luminescence droplets: Characterization and applications in medical beams

Optically stimulated luminescence (OSL) detectors, which are widely used in radiation protection, offer a number of potential advantages for radiotherapy dosimetry. In this study we characterized 1-μl of OSL droplets consisting of a mixture of Al₂O₃:C powder and a photo-curable polymer, in addition to results described in a previous work (Nascimento et al., 2013). The concentration test showed that droplets have a higher spatial resolution than other commonly used Al₂O₃:C-based detectors. Our results from the dose response, reproducibility and dependence with accumulative dose were obtained for droplets with a powder/polymer concentration that showed a high Signal to Noise Ratio (SNR) without compromising the droplet malleability. Additional test results show the response of such droplets in percentage depth dose curves and dose profiles of clinical beams.     

Comparison of the properties of various optically stimulated luminescence signals from potassium feldspar

Various optically stimulated luminescence signals from K-feldspar have been used to determine the equivalent doses of sediment samples. Understanding the properties of these optical signals is critical to evaluate their applicability and limitations to optical dating. In this paper, some properties of IRSL, post-IR OSL and post-IR IRSL signals (detected in the UV region using U-340 filters) from a museum sample of K-feldspar were investigated by analyzing the relationships between optical and TL signals, and the effect of optical bleaching and heating on optical signals. The trap parameters of the different optical signals were calculated using the pulse annealing method. The results show that this sample exhibits two regenerated TL peaks at ～140 and ～330 °C. Corresponding to the low temperature TL peak, the OSL and post-IR OSL signals appear to be more associated with lower temperature TL than the IRSL signal measured at 50 °C. Corresponding to the high temperature TL peak, the post-IR IRSL signals mainly originate from the more thermally stable traps associated with the high temperature TL, compared with the IRSL and post-IR OSL signals. However, the post-IR IRSL_225 °C signal is shown to be hard to be bleached by blue light and simulated sunlight, compared with the IRSL_50 °C and low temperature post-IR IRSL signals. The implication for optical dating is that the elevated temperature post-IR IRSL signals can be preferentially applied over other signals from K-feldspar, but it is desirable that the effectiveness of the pre-depositional zeroing of these signals is assessed.     

Review of optically stimulated luminescence (OSL) instrumental developments for retrospective dosimetry

This review describes 40 years of experience gained at Risø National Laboratory in the development of facilities for irradiation, thermal/optical stimulation and luminescence signal detection. These facilities have mainly been used in luminescence dating and nuclear accident dosimetry. We focus especially on methods for light stimulation and irradiation, and developments of new portable TL/OSL readers for determining doses directly in the field on both Earth and the planet Mars.     

Application of the optically stimulated luminescence (OSL) technique in space dosimetry

This paper reviews the state of the optically stimulated luminescence (OSL) technique for space dosimetry applications, focusing on the properties of carbon-doped aluminum oxide (Al₂O₃:C). New data presented include the most complete and recent values for the relative efficiency η_HCP,γ for heavy charged particles as a function of the incident radiation's linear energy transfer (LET), obtained through ground-based experiments at heavy ion accelerators. We also discuss the factors influencing the OSL efficiencies, the LET-dependent properties of Al₂O₃:C, and the experience gained from past space experiments using Al₂O₃:C. The characterization of the OSL efficiency values as a function of LET allows the use of the OSL of Al₂O₃:C in combination with plastic nuclear track detectors for personal dosimetry of astronauts, as proposed by the NCRP Report 142.