Effect of annealing on natural calcitic crystals—A thermostimulated luminescence (TSL) study

The quality crystals (Calcitic limestone) were selected using the UV–visible methylene blue adsorption method. The thermostimulated luminescence (TSL) glow curve characteristics of six well crystallized limestone samples were analyzed. The glow curves of unannealed sample show only one peak in the range 320–330 °C. The sample irradiated with a gamma dose of 100 Gy shows two additional peaks in the range of 113–125 °C and 242–260 °C when recorded with linear heating rate of 10 °C/s. The annealed sample also shows the same trend as that of irradiated sample. Annealing treatment above 250 °C increases the sensitivity of all TSL peaks except 320 °C. On the other hand, annealing at 750 °C caused a collapse in the TSL sensitivity. The enhancement in TSL sensitivity was found to depend on the annealing temperature and time. Annealing treatment at 650 °C for 4 h followed by quenching in air is the optimum condition for TSL sensitization. The response to gamma irradiation is linear in the range from 0.5 Gy to 10⁴ Gy. The emission spectra of all the samples show an emission at around 610 nm but with different intensities for each TSL peak. With reference to earlier work, it may be assumed that the recombination site always involves Mn²⁺ ions. The observation made through infra-red (IR) and X-ray diffraction (XRD) studies with thermal treatment shows the structural changes of calcite from D_3h to C_s symmetry at 750 °C. The Thermogravimetric-Differential Thermal Analysis (TG-DTA) analysis shows the calcite gets disordered at 760 °C. Hence, the collapse in the TSL sensitivity at 750 °C is due to structural change or structural disorderedness.     

Radioluminescence of synthetic quartz related to alkali ions

The radioluminescence (RL) of synthetic quartzes (GEMMA Quartz & Crystal Company) has been measured at room temperature. Some samples were treated by electrodiffusion (“sweeping”) in order to change the concentrations of alkali ions, mainly Li⁺ and Na⁺, which in quartz are known to be linked to Al ions, substitutional for Si ions.The RL emission spectra show evidence of a role of alkali ions in affecting some specific emissions. All the spectra could be analysed as composed of four bands in the blue and UV region. Specifically, the well known blue emission at around 470 nm was seen to be composed by two bands at 430 nm (2.86 eV) and at 485 nm (2.53 eV). Effects of irradiation, during the RL measurements, were clearly seen only in the “Li swept in” sample, namely an increase in the 485 nm band intensity and a decrease in the 430 nm band one. The previously reported UV emission was detected at 355 nm (3.44 eV) in all the samples, being the most intense band in the “swept out” sample. A further UV emission was detected at 315 nm (3.94 eV), more intense in untreated samples.Possible assignments of the detected emission bands are discussed in relation to the defects of quartz, specifically focusing on the Al centres that are most affected by sweeping procedures.     

The unusual variations of photoluminescence and afterglow properties in monoclinic ZrO2 by annealing

The raw ZrO₂ is annealed at 600–1550 °C for 6 h. It is found that the emission at 492 nm increases greatly when the annealing temperature is higher than 1200 °C and its afterglow shows a small improvement at 1200–1450 °C and a large enhancement after annealing at 1550 °C. The results that are obtained indicate that the impurity Ti⁴⁺ in ZrO₂ is efficiently reduced to Ti³⁺ when the temperature is higher than 1200 °C, and the increase of Ti³⁺ centers contributes to the large improvement of emission at 492 nm. The thermoluminescence shows that at least two types of traps with different depths (0.65 eV and 1.46 eV) corresponding to oxygen vacancies exist in monoclinic ZrO₂. After annealing at 1200–1450 °C, some new trap clusters related to oxygen vacancies and Ti³⁺ form and causes the small improvement of afterglow at 1200–1450 °C. The large improvement of afterglow after annealing at 1550 °C originates from the sharp increase of proper shallow traps (0.65 eV) in ZrO₂. Accordingly, we present the feasible interpretations and luminescence mechanisms of monoclinic ZrO₂ for our observations.     

Effect of Eu and Pb doping on the dosimetric properties of LiCAF

LiCaAlF₆ (LiCAF) crystals doped with two different ions (europium and lead) have been investigated as potential new dosimetric materials. The stability of thermally stimulated luminescence (TSL) glow peaks in LiCAF:Eu was evaluated by means of the initial rise technique. The decay times at room temperature of the traps related to the dosimetric glow peaks were found to range between 40 and 2 × 10⁴ years confirming the good dosimetric characteristics of this crystal. The glow curve of LiCAF:Pb is dominated by a peak at approximately 300 °C emitting in the UV region (³P_0,1–¹S₀ transition of Pb²⁺) superimposed to a very broad structure at lower temperature (20–200 °C) featuring recombination at an intrinsic defect centre. The anomalous behavior of the low temperature structure during thermal cleaning procedures prevented any reliable numerical analysis of the TSL glow peak at 300 °C.     

Growth-morphology-luminescence correlation in ZnO-containing nanostructures synthesized in different media

Zinc hydroxide particles were prepared by a two-step process employing zinc nitrate hexahydrate, urea, ethylene glycol, water and p-toluene-sulfonic acid monohydrate (p-TSA). We used different concentrations of the reactants as well as different volume ratios of the solvents. ZnO particles were obtained by thermal treatment of the reaction products at two different temperatures: 350 °C and 500 °C. The samples were characterized by scanning field emission electron microscopy (SEM), X-ray diffraction (XRD) spectroscopy, BET analysis, thermogravimetry (TG) analysis and photoluminescence (PL) spectroscopy. It was found that after the thermal treatment particles become smaller, with the p-TSA concentration strongly affecting the morphology of the particles. Luminescence properties of the samples probed by PL at 8 K and room temperature exhibited a remarkable correlation with specimens′ nanomorphology. Luminescent features at ～2.0–2.2 eV, ～2.4–2.5 eV, ～2.65 eV, ～2.9 eV, ～3.0–3.1 eV and ～3.3 eV were observed in most specimens, although their relative intensity and temperature dependence were specific to an individual group of samples vis-à-vis their growth history and morphology.     

Synthesis and photoluminescence properties of silver nanowires

Silver nanowires of 50–190 nm in diameters along with silver nanoparticles in the size range of 60–200 nm in prismatic and hexagonal shapes are synthesized through chemical process. The lengths of the silver nanowires lie between 40 and 1000 μm. The characterizations of the synthesized samples are done by X-ray diffraction (XRD), scanning electron microscopy (SEM) and UV–visible absorption spectroscopy. The syntheses have been done by using two processes. In the first process, relatively thicker and longer silver nanowires are synthesized by a soft template liquid phase method at a reaction temperature of 70 °C with methanol as solvent. In the second process, thinner silver nanowires along with silver nanoparticles are prepared through a polymer mediated polyol process at a reaction temperature of 210 °C with ethylene glycol as solvent. The variations of photoluminescence (PL) emission from the silver nanocluster dispersed in methanol as well as in ethylene glycol are recorded at room temperature under excitation wavelengths lying in between 300 and 414 nm. The blue–green PL emission is observed from the prepared samples and these emissions are assigned to radiative recombination of Fermi level electrons and sp- or d-band holes.     

High c-axis preferred orientation ZnO thin films prepared by oxidation of metallic zinc

Thin films of zinc oxide were grown on glass substrates by thermal oxidation. The metallic zinc films were thermally oxidized at different temperatures ranging from 300 to 600 °C to yield ZnO thin films. The structural property of the thin films was characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The X-ray diffraction measurements showed that the films oxidized at 300 °C were not oxidized entirely, and the films deposited at 600 °C had better crystalline quality than the rest. When the oxidation temperature increased above 400 °C, the films exhibited preferred orientation along (002) and high transmittance ranging from 85% to 98% in vis–near-infrared band. Meanwhile, the films showed a UV emission at about 377 nm and green emission. With the increasing of oxidation temperature, the intensity of green emission peak was enhanced, and then decreased, disappearing at 600 °C, and the case of UV emission increased. Furthermore, a strong green emission was observed in the film sintered in pure oxygen atmosphere.     

A facile thermal evaporation route for large-area synthesis of tin oxide nanowires: Characterizations and their use for liquid petroleum gas sensor

In this paper, a very simple procedure was presented for the reproducible synthesis of large-area SnO₂ nanowires (NWs) on a silicon substrate by evaporating Sn powders at temperatures of 700, 750, and 800 °C. As-obtained SnO₂ NWs were characterized by field emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), and Raman spectroscopy. They revealed that the morphology of the NWs is affected by growth temperature and the SnO₂ NWs are single-crystalline tetragonal. The band gap of the NWs is in the range of 4.2–4.3 eV as determined from UV/visible absorption. The NWs show stable photoluminescence with an emission peak centered at around 620 nm at room-temperature. The sensors fabricated from the SnO₂ NWs synthesized at 700 °C exhibited good response to LPG (liquefied petroleum gas) at an operating temperature of 400 °C.     

Photoluminescence studies of ZnO thin films on R-plane sapphire substrates grown by sol–gel method

Zinc oxide (ZnO) thin films on R-plane sapphire substrates were grown by the sol–gel spin-coating method. The optical properties of the ZnO thin films were investigated using photoluminescence. In the UV range, the asymmetric near-band-edge emission was observed at 300 K, which consisted of two emissions at 3.338 and 3.279 eV. Eight peaks at 3.418, 3.402, 3.360, 3.288, 3.216, 3.145, 3.074, and 3.004 eV, which respectively correspond to the free exciton (FX), bound exciton, transverse optical (TO) phonon replica of FX recombination, and first-order longitudinal optical phonon replica of FX and the TO (1LO+TO), 2LO+TO, 3LO+TO, 4LO+TO, and 5LO+TO, were obtained at 12 K. From the temperature-dependent PL, it was found that the emission peaks at 3.338 and 3.279 eV corresponded to the FX and TO, respectively. The activation energy of the FX and TO emission peaks was found to be about 39.3 and 28.9 meV, respectively. The values of the fitting parameters of Varshni's empirical equation were α=4×10^?3 eV/K and β=4.9×10³ K, and the S factor of the ZnO thin films was 0.658. With increasing temperature, the exciton radiative lifetime of the FX and TO emissions increased. The temperature-dependent variation of the exciton radiative lifetime for the TO emission was slightly higher than that for the FX emission.     

Influence of rapid thermal annealing on electrical and structural properties of double metal structure Au/Ni/n-InP (1 1 1) diodes

The effect of rapid thermal annealing on the electrical and structural properties of Ni/Au Schottky contacts on n-InP have been investigated by current–voltage (I–V), capacitance–voltage (C–V), auger electron spectroscopy (AES) and X-ray diffraction (XRD) techniques. The Au/Ni/n-InP Schottky contacts are rapid thermally annealed in the temperature range of 200–500 °C for a duration of 1 min. The Schottky barrier height of as-deposited Ni/Au Schottky contact has been found to be 0.50 eV (I–V) and 0.86 eV (C–V), respectively. It has been found that the Schottky barrier height decreased with increasing annealing temperature as compared to as-deposited sample. The barrier height values obtained are 0.43 eV (I–V), 0.72 eV (C–V) for the samples annealed at 200 °C, 0.45 eV (I–V) and 0.73 eV (C–V) for those at 400 °C. Further increase in annealing temperature to 500 °C the barrier height slightly increased to 0.46 eV (I–V) and 0.78 eV (C–V) compared to the values obtained for the samples annealed at 200 °C and 400 °C. AES and XRD studies showed the formation of indium phases at the Ni/Au and InP interface and may be the reason for the increase in barrier height. The AFM results showed that there is no significant degradation in the surface morphology (rms roughness of 1.56 nm) of the contact even after annealing at 500 °C.     

Effect of reaction temperature on the size and morphology of scorodite synthesized using ultrasound irradiation

Synthesis of scorodite (FeAsO₄·2H₂O) using dynamic action agglomeration and the oxidation effect from ultrasound irradiation was investigated. The effect of different reaction temperatures (90, 70, 50, and 30 °C) on the size and morphology of scorodite particles synthesized under O₂ gas flow and ultrasound irradiation was explored because the generation of fine bubbles depends on the solution temperature. At 90 °C, the size of scorodite particles was non-homogeneous (from fine particles (<1 μm) to large particles (>10 μm)). The oxidation–reduction potential (ORP) and yield at 90 °C showed lower values than those at 70 °C. The scorodite particles, including fine and non-homogeneous particles, were generated by a decrease in the oxidation of Fe(II) to Fe(III) and promotion of dissolution caused by the generation of radicals and jet flow from ultrasound irradiation. Using ultrasound irradiation in the synthesis of scorodite at low temperature (30 °C) resulted in the appearance of scorodite peaks in the X-ray diffraction (XRD) pattern after a reaction time of 3 h. The peaks became more intense with a reaction temperature of 50 °C and crystalline scorodite was obtained. Therefore, ultrasound irradiation can enable the synthesis of scorodite at 30 °C as well as the synthesis of large particles (>10 μm) at higher temperature. Oxide radicals and jet flow generated by ultrasound irradiation contributed significantly to the synthesis and crystal growth of scorodite.     

Densification and microstructure of lead zirconate titanate ceramics fabricated from a triol sol–gel powder

Lead zirconate titanate (PZT) nano-powder was prepared by a triol sol–gel process. X-ray diffraction and transmission electron microscopy results showed that as-synthesized amorphous powder started to crystallize at the calcination temperature above 500 °C. The crystalline powder was formed into pellets and sintered at temperatures between 900 and 1300 °C. Co-existence of tetragonal and rhombohedral phase was observed in all ceramics. Microstructural investigation of PZT ceramics showed that uniform grain size distribution with average grain size of ∼0.8–2.5 μm were received with sintering temperature up to 1200 °C. Further increasing the temperature caused abnormal grain growth with the grain as large as 13.5 μm. An attempt to optimize densification with uniform grain size distribution was also performed by varying heating rate and holding time during sintering. It was found that dense (∼97%) sol–gel derived PZT ceramic with uniform microstructure was achieved at 1100 °C with a heating rate of 5 °C min⁻¹ and 6 h dwell time.     

Effect on thermoluminescence parameters of biotite mineral due to thermal quenching

The Thermally Stimulated Luminescence (TSL) at room temperature X-ray irradiated natural biotite in form of micro-grain powder was studied under various heating rates. TSL peaks showed at temperatures 393 K, 399.6 K, 403.5 K, 404.5 K, 406.9 K at their respective heating rates 2 K/s, 4 K/s, 6 K/s, 8 K/s and 10 K/s. The effect of thermal quenching on thermoluminescence parameters such as peak maximum temperature, peak area, FWHM, geometrical symmetry factor, the activation energy were investigated. From the symmetry factor it is clear that the TL glow curve follows the first order kinetics for the lowest heating rate, but as the heating rate increases it defers from the first order. The activation energies for each heating rates were calculated by using Chen peak shape methods for general order kinetics and found to be decreased for higher heating rates. When activation energy is calculated by variable heating rate method it is observed that the method overestimated the value of activation energy and pre-exponential frequency factor significantly due to thermal quenching.     

Cathodoluminescence studies of un-doped and (Cu,Fe, and Co)-doped tin dioxide films deposited by spray pyrolysis

Un-doped and (Cu, Fe, and Co)-doped SnO₂ were studied using films deposited by spray pyrolysis. Room temperature cathodoluminescence (CL) was measured. Differences in CL spectra were observed as a function of deposition parameters (T_sub-350–550 °C), the nature and concentration of dopants (0–16 at.%), and the resulting high annealing temperature (T_an = 700–950 °C). A possible luminescence mechanism has been discussed. It was established that changes taking place in CL spectra were caused by the change of both the grain size and crystallinity (stoichiometry) of the surface layer. It was concluded that radiative recombination occurs through shallow donor levels associated with O-vacancies and trapped centers. It was assumed that in SnO₂ there are apparently three types of defects forming deep levels located at 0.8–0.9, 1.3–1.4, and ∼1.6 eV from the top of the valence band.     

Synthesis of nanocrystalline ZnO nanobelts via pyrolytic decomposition of zinc acetate nanobelts and their gas sensing behavior

The pyrolytic decomposition of layered basic zinc acetate (LBZA) nanobelts (NBs) into nanocrystalline ZnO NBs is investigated using scanning electron microscopy (SEM), atomic force microscopy (AFM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and photoluminescence (PL). We also report on the gas sensing response of the resulting ZnO nanomaterial to CO. The LBZA NBs are grown at 65 °C in an aqueous solution of zinc acetate dihydrate. AFM and SEM results show as-grown products possess the characteristic layered structure of the LBZA crystals. XRD and XPS results show that annealing as-grown products at 210 °C in air causes a transformation from zinc acetate to nanocrystalline ZnO NBs via thermal decomposition. The ZnO crystalline domain size increases with temperature from 9.2 nm at 200 °C to 94 nm at 1000 °C, as measured from XRD. SEM shows evidence of sintering at 600 °C. The thickness of the NBs, determined via AFM, ranges from 10 to 50 nm and remains approximately constant with annealing temperature. XPS confirmed the chemical transformation from zinc acetate to ZnO and showed a significant remaining zinc hydroxide component for the ZnO NBs consistent with published results. PL measurements at room temperature show a blue shift in peak emission as the nanobelts change from LBZA to ZnO at 200 °C. Above this transition temperature, the ZnO nanobelts possess strong band edge emission at 390 nm and little broad band emission in the visible region. The AFM and SEM images reveal that the crystallites within the nanobelts orientate in rows along the long axis during annealing. This structure provides a high surface area to volume ratio of aligned nanoparticles which is beneficial for gas sensing applications. Gas sensors fabricated from 400 °C annealed nanobelts showed a response of 1.62 when exposed to 200 ppm of CO in dry air at 400 °C, as defined by the ratio of resistance before and during exposure. This indicates that ZnO nanostructures obtained by thermal decomposition of LBZA NBs could provide a cost effective route to high sensitivity gas sensors.     

Photoluminescence of chemical solution-derived amorphous ZnO layers prepared by low-temperature process

Growth characteristic and optical properties of the amorphous ZnO thin films prepared on soda-lime–silica glass substrates by chemical solution process at 100 and 200 °C were investigated by using X-ray diffraction analysis, scanning probe microscope, ultraviolet spectrophotometer, and photoluminescence. The films exhibited an amorphous pattern even when finally heat treated at 100–200 °C for 60 min. The photoluminescence spectrum of amorphous ZnO films shows a strong near-band-edge emission, while the visible emission is nearly quenched.     

A spectroscopic ellipsometry study of TiO2 thin films prepared by ion-assisted electron-beam evaporation

Film characterization based on variable-angle spectroscopic ellipsometry (VASE) is desirable in order to understand physical and optical characteristics of thin films. A number of TiO₂ film samples were prepared by ion-assisted electron-beam evaporation with 200-nm nominal thickness, 2.0 Å/s deposition rate and 8 sccm oxygen flow rate. The samples were maintained at 250 °C during the deposition, and annealed in air atmosphere afterwards. As-deposited and annealed films were analyzed by VASE, spectrophotoscopy and X-ray diffractometry. From ellipsometry modeling process, the triple-layer physical model and the Cody–Lorentz dispersion model offer the best results. The as-deposited films are inhomogeneous, with luminous transmittance and band gap of 62.37% and 2.95 eV. The 300 °C and 500 °C are transition temperatures toward anatase and rutile phases, respectively. Increasing temperature results in an increase of refractive index, transmittance percentage and band gap energy. At 500 °C, the highest refractive index and band gap energy are obtained at 2.62 and 3.26 eV, respectively. The developed VASE-modeling process should be able to characterize other TiO₂ films, using similar physical and optical modeling considerations.     

Green and red photoluminescence from ZnAl2O4:Mn phosphors prepared by sol–gel method

Luminescence investigations of Mn-activated ZnAl₂O₄ phosphors prepared by using sol–gel method were described. The phosphor was characterized by X-ray diffraction (XRD) and electronic paramagnetic resonance (EPR). The EPR spectra of the samples suggested that Mn ions possessed homogeneous distribution in ZnAl₂O₄ phosphors. Photoluminescence studies of the prepared phosphors showed green and red emissions. The red emission became weaker, and vanished at last with sintering temperature increasing from 600 to 900 °C in reducing atmosphere, while the intensity of green emission peak increased. Furthermore, when the phosphor was sintered at 900 °C in air, the intensity of red and green emissions decreased, but the value of intensity ratio increased. It suggested that the green emission resulted from Mn²⁺ and the red emission resulted from Mn⁴⁺.     

Structural evolution,growth mechanism and photoluminescence properties of CuWO4 nanocrystals

Copper tungstate (CuWO₄) crystals were synthesized by the sonochemistry (SC) method, and then, heat treated in a conventional furnace at different temperatures for 1 h. The structural evolution, growth mechanism and photoluminescence (PL) properties of these crystals were thoroughly investigated. X-ray diffraction patterns, micro-Raman spectra and Fourier transformed infrared spectra indicated that crystals heat treated and 100 °C and 200 °C have water molecules in their lattice (copper tungstate dihydrate (CuWO₄·2H₂O) with monoclinic structure), when the crystals are calcinated at 300 °C have the presence of two phase (CuWO₄·2H₂O and CuWO₄), while the others heat treated at 400 °C and 500 °C have a single CuWO₄ triclinic structure. Field emission scanning electron microscopy revealed a change in the morphological features of these crystals with the increase of the heat treatment temperature. Transmission electron microscopy (TEM), high resolution-TEM images and selected area electron diffraction were employed to examine the shape, size and structure of these crystals. Ultraviolet–Visible spectra evidenced a decrease of band gap values with the increase of the temperature, which were correlated with the reduction of intermediary energy levels within the band gap. The intense photoluminescence (PL) emission was detected for the sample heat treat at 300 °C for 1 h, which have a mixture of CuWO₄·2H₂O and CuWO₄ phases. Therefore, there is a synergic effect between the intermediary energy levels arising from these two phases during the electronic transitions responsible for PL emissions.     

Temperature dependent structural and optical properties of tin oxide nanoparticles

Nanocrystalline tin oxide (SnO₂) powders were synthesized through wet chemical route using tin metal as precursor. The morphology and optical properties, as well as the effect of sintering on the structural attributes of SnO₂ particles were analyzed using Transmission electron microscopy (TEM), UV–visible spectrophotometry (UV–vis) and X-ray diffraction (XRD), respectively. The data revealed that the lattice strain plays a significant role in determining the structural properties of sintered nanoparticles. The particle size was found to be 5.8 nm, 19.1 nm and 21.7 nm for samples sintered at 300 °C, 500 °C, and 700 °C, respectively. Also, the band gaps were substantially reduced from 4.1 eV to 3.8 eV with increasing sintering temperatures. The results elucidated that the structural and optical properties of the SnO₂ nanoparticles can be easily modulated by altering sintering temperature during de novo synthesis.