Substrate dependent structure and in-plane dielectric properties of Ba(Sn0.15Ti0.85)O3 thin films

The structure, microstructure and in-plane dielectric properties of Barium tin titanate Ba(Sn_0.15Ti_0.85)O₃ (BTS) thin films grown on (100) LaAlO₃ (LAO) and (100) MgO single crystal substrates through sol–gel process were investigated. The films deposited on (100) LAO substrate exhibited a strong (100) preferred orientation while the film deposited on (100) MgO substrate showed polycrystalline structure. The in-plane ɛ–T measurements reveal that the films grown on (100) LAO substrate exhibited an obvious room-temperature ferroelectric state, while the film grown on MgO substrate showed paraelectric state in the temperature range of 10–130 °C. A high tunability of 52.11% was observed for the BTS films deposited on (100) LAO substrate at the frequency of 1 MHz with an applied electric field of 80 kV/cm, which is about two times larger than that of the BTS films deposited on (100) MgO substrate. The obvious differences in the dielectric properties could be attributed to the stress in the films, which come from lattice mismatch and difference in the thermal expansion coefficients between the film and substrates. This work clearly reveals the highly promising potential of BTS films for application in tunable devices.     

Electrochemical fabrication of novel fluorescent polymeric film: Poly(pyrrole–pyrene)

We describe herein the electrochemical characterization and polymerization of 4-pyren-1-yl-butyric acid 11-pyrrol-1-yl-decyl ester (pyrrole–pyrene) in CH₃CN. The electrochemical oxidation of the pyrrole group at 0.77 V vs Ag/Ag + 10 mM in CH₃CN led to the first example of a fluorescent polypyrrole film. The mechanism of deposition on platinum electrode was studied by voltammetry and chronoamperometry. The optical properties of the polymeric films electrogenerated on ITO electrodes were examined by UV–visible spectroscopy and fluorescence microscopy indicating an increase in fluorescence properties by increased polymer thickness. The electrochemical oxidation of pyrenyl group linked to the polypyrrole backbone was carried out at 1.2 V. This additional polymerization was demonstrated by UV–visible spectroscopy and induced the loss of the fluorescence properties of the resulting polymeric film.     

The synthesis of free-standing films of polymer/nanocarbon composites using the carbon nanopowder's buoyancy

In this work we report the synthesis of free-standing films of polymer/nanocarbon composites. The method consists in forming a thin film of carbon nanoparticles onto the water's surface. Through the free infiltration of the polymer between the nanoparticles which form the film, after the polymer is cured, we obtain free-standing films of polymer/nanocarbon composites. The composite films are homogeneous; they have 5 wt.% carbon nanoparticles within the polymer matrix and are a few micrometers in thickness.     

Layer-by-layer assembled protein/polymer hybrid films: nanoconstruction via specific recognition

In the present study it is shown that streptavidin-containing multilayer films with varying numbers of polyelectrolyte spacer layers can be fabricated reproducibly using optimized deposition conditions. Direct alternation of streptavidin and PLB leads to multilayer systems with an average streptavidin thickness of 5.3 nm which is in good agreement with the dimensions of the protein. When the streptavidin layers are spacered by more polyelectrolyte layers the distance between the protein sheets is increased up to e.g. 6.5 nm in the case of (PLB/PSS/PAH/PSS/PLB) as spacer layer. X-ray reflectivity reveals that streptavidin increases the surface roughness of the films probably due to the rigid three-dimensional structure of the protein. The control of surface roughness seems to be essential for a successful multilayer build-up. The property of PLB to provide for multilayer construction by two different interactions (electrostatic and specific) allowed to probe the interpenetration depth of adjacent layers. For the [PLB/(PSS/PL)₂/streptavidin] system an interpenetration depth of about 4 polymer layers corresponding to approximately 3.4 nm has been derived. These data are in agreement with a model for pure polyelectrolyte films obtained from neutron and X-ray reflectivity data.     

Molecular patterning with a two-dimensional network polymer LB film 2: Drawing patterns by an electron beam

Electron beam lithography was investigated using a cross-linkable polymer Langmuir–Blodgett (LB) film. Cross-linking reaction occurs in the LB film with electron beam irradiation as well as UV light irradiation and the irradiated LB film becomes insoluble in the organic solvents to form a two-dimensional network in the LB film. The sensitivity and contrast of the cross-linkable polymer LB film are 3 μC cm^-2 and 0.64, respectively. The limiting resolution of patterning is 0.2 μm line-and-space. The electron beam lithography using the cross-linkable polymer LB film is applicable to the future nanotechnology.     

Synthesis and properties of polyfluorene copolymers bearing thiophene and porphyrin

To search for more wider absorption and higher charge carriers mobilities materials of polymer solar cell, a series of soluble alternating polyfluorene copolymers were synthesized by palladium-catalyzed Suzuki coupling reaction. Their structures were determined by 1H NMR, IR and UV-vis. And their UV-vis absorption spectra indicated that they had strong absorption over 600 nm spectral range and nearly cover 400-700 nm visible region. The band gaps of copolymers calculated according to cyclic voltammetry （CV） were between 1.96 and 2.03 eV. Polymer：TiO2 bulk-heterojunction films were made from mixtures of polymer and titanium isopropoxide, a precursor for TiO2, via hydrolysis in air overnight. The photoluminescence at 380-800 nm of the blend film of PT-TPP20 （5 mg/mL）：Ti（OC3H7）4 （80 μL/mL） （20% volume fraction） was significantly quenched in the 50% Ti（OC3H7）4 blend film, indicating that rapid and efficient separation of photoinduced electron-hole pairs.     

Investigation of immiscible alloy system of Al–Sn thin films as anodes for lithium ion batteries

The Al–Sn, which is immiscible alloy, film was prepared by e-beam deposition to explore the possibility as anode material for lithium ion batteries for the first time. The film has a complex structure with tiny Sn particles dispersed homogeneously in the Al active matrix. The diffusion coefficients of Li⁺ in these Al–Sn alloy films were determined to be 2.1–3.2 × 10⁻⁸ cm²/s by linear sweep voltammetry. The film electrode with high Al content (Al–33wt%Sn) delivered a high initial discharge capacity of 972.8 mA h g⁻¹, while the film electrode with high Sn content (Al–64wt%Sn) with an initial discharge capacity of 552 mA h g⁻¹ showed good cycle performance indicated by retaining a capacity of about 381 mA h g⁻¹ after 60 cycles. Our preliminary results demonstrate that Al–Sn immiscible alloy is a potential candidate for anodic material of lithium ion batteries.     

Thick lanthanum zirconate buffer layers from water-based precursor solutions on Ni-5%W substrates

In this work, water-based precursor solutions suitable for dip-coating of thick La₂Zr₂O₇ (LZO) buffer layers for coated conductors on Ni-5%W substrates were developed. The solutions were prepared based on chelate chemistry using water as the main solvent. The effect of polymer addition on the maximum crack-free thickness of the deposited films was investigated. This novel solution preparation method revealed the possibility to grow single, crack-free layers with thicknesses ranging 100–280 nm with good crystallinity and an in-plane grain misalignment with average FWHM of 6.55°. TEM studies illustrated the presence of nanovoids, typical for CSD–LZO films annealed under Ar-5%H₂ gas flow. The appropriate buffer layer action of the film in preventing the Ni diffusion was studied using XPS. It was found that the Ni diffusion was restricted to the first 30 nm of a 140 nm thick film. The surface texture of the film was improved using a seed layer.     

Structural and electrical characterization of boron-containing diamond-like carbon films deposited by femtosecond pulsed laser ablation

The present study investigates the influence of the incorporation of boron in Diamond-Like Carbon (DLC) films deposited by femtosecond laser ablation, on the structure and electrical properties of the coatings within the temperature range 70–300 K. Doping with boron has been performed by ablating alternatively graphite and boron targets. The film structure and composition have been highlighted by coupling Atomic Force Microscopy (AFM), Scanning Electron Microscopy equipped with a field emission gun (SEM-FEG) and High Resolution Transmission Electron Microscopy (HRTEM). Boron dilution ranges between 2 and 8% and appears as nanometer size clusters embedded in the DLC matrix. Typical resistivity values are 100 W cm for pure a-C films, down to few W cm for a-C:B films at room temperature. The resistance decreases exponentially when the temperature increases in the range 70–300 K. The results are discussed considering the classical model of hopping conduction in thin films. Some coatings show temperature coefficients of resistance (TCR) as high as 3.85%. TCRs decrease when the doping increases. Such high values of TCR may have interests in the use of these films as thermometer elements in micro and nanodevices.     

Scanning angle Raman spectroscopy measurements of thin polymer films for thickness and composition analyses

Scanning angle (SA) Raman spectroscopy was used to measure the thickness and composition of polystyrene films. A sapphire prism was optically coupled to a sapphire substrate on which 6–12% (w/v) polystyrene in toluene was spin coated. Raman spectra were collected as the incident angle of the p-polarized, 785-nm excitation laser was varied from 56 to 70°. These angles span above and below the critical angle for a sapphire/polystyrene interface. The thickness of the polystyrene film was determined using a calibration curve constructed by calculating the integrated optical energy density distribution as a function of incident angle, distance from the prism interface and polymer thickness. The calculations were used to determine the incident angle where waveguide modes are excited within the polymer film, which is the angle with the highest integrated optical energy density. The film thicknesses measured by SA Raman spectroscopy ranged from less than 400 nm to 1.8 μm. The average percent uncertainty in the SA Raman determinations for all films was 4%, and the measurements agreed with those obtained from optical interferometery within the experimental uncertainty for all but two films. For the 1270-nm and 580-nm polystyrene films, the SA Raman measurements overestimated the film thickness by 5 and 18%, respectively. The dependence of the calibration curve on excitation polarization and composition of the polymer and bulk layers was evaluated. This preliminary investigation demonstrates that scanning angle Raman spectroscopy is a versatile method applicable whenever the chemical composition and thickness of interfacial polymer layers needs to be measured.     

Anti-biofouling properties of amphiphilic phosphorylcholine polymer films

Surfaces of amphiphilic phosphorylcholine polymer (PC1036) prepared by spin-coating were characterized by spectroscopic ellipsometry, water contact angle and atomic force microscopy. The antifouling properties of the PC1036 films to marine benthic diatom Nitzschia closterium MMDL533 were also investigated. The results showed that the dry PC1036 film promoted the adhesion of N. closterium MMDL533 because the hydrophobic lauryl groups were present in the film surface. The 2 h-swelled PC1036 films had excellent anti-fouling properties with extremely low attachment densities and retention densities no matter what the annealing temperature was. The thickness of the coated films lower than 147 Å had a profound effect on the film anti-fouling properties. Otherwise, when the film thickness was higher than that value, there was no more improvement of diatom cell reduction observed. The annealing temperature had only a little effect on the film resistant to diatom adhesion, which might be attributed to two factors including the PC group packing densities in the outer PC layer and the equilibrated water volume fraction in the 2 h-swelled PC1036 films.     

Preparation of poly(ether ether ketone)-based polymer electrolytes for fuel cell membranes using grafting technique

Poly(ether ether ketone) (PEEK)-based polymer electrolyte membranes (PEMs) was successfully prepared by radiation grafting of a styrene monomer into PEEK films and the consequent selective sulfonation of the grafting chains in the film state. Using milder sulfonation, the sulfonation reactions proceeded at the grafted chains in preference to the phenylene rings of PEEK main chains; as a result, the grafted films could successfully transform to a PEM with conductivity of more than 0.1 S/cm. The ion exchange capacity (IEC) and conductivity of the grafted PEEK electrolyte membranes were controlled to the ranges of 1.2–2.9 mmol/g and 0.03–0.18 S/cm by changing the grafting degree. It should be noted that this is the first example of directly transforming super-engineering plastic films into a PEM using radiation grafting.     

The influence of local structure of nanocrystalline Ni films on the catalytic activity

The aim of our investigation was to study the influence of the nanoparticles size (the local structure) in sputter deposited Ni films on hydrogen evolution kinetics. The grain size of Ni-particles (11–100 nm) was controlled by the substrate temperature (from 35 °C to 300 °C). The dependence of the kinetic parameters on the temperature at which the films were deposited was measured in alkaline solution by electrochemical impedance spectroscopy (EIS). It correlates well with the change of the ratio between the nanocrystalline and non-homogenous disordered fraction of the nc-Ni film observable by Grazing incidence small angle X-ray scattering (GISAXS) analysis and ascribed to the intercrystalline matter. The catalytic activity of nanocrystalline nickel (nc-Ni) on the hydrogen evolution reaction (h.e.r.) is markedly greater at larger fraction of the spherical inhomogeneities inside the film. This effect is especially strongly pronounced for the nc-Ni films prepared on the substrates at lower temperatures.     

Enhancement in as-grown CuInSe2 film microstructure by a three potential pulsed electrodeposition method

P-type copper indium diselenide (CuInSe₂) films have been prepared onto ITO substrates by an electrodeposition method, that sequentially applies potential pulses at the deposition potential of each element Cu, Se and In, and then step it back in cyclically to induce the solid state reaction between the elements. Two electrolyte concentrations as well as three different pulse durations were assessed. The resulting films were compared with those deposited at fixed electrode potentials. As-grown films are nanocrystalline and have an E_g ～ 0.95 eV. Raman spectroscopy shows that Se and Cu–Se contents decrease while pulse duration increases and electrolyte concentration decreases. Cu–Se phases are even absent for films grown at the low electrolyte concentration. These results represent a great improvement in the film phase purity reducing the need of post-deposition treatments.     

Thickness dependent physical properties of close space evaporated In2S3 films

In recent years, In₂S₃ is considered as a promising buffer layer in the fabrication of heterojunction solar cells. Film thickness is one of the important parameters that alters the physical characteristics of the grown layers significantly. The effect of film thickness on the structural, morphological, optical and electrical properties of close space evaporated In₂S₃ layers has been studied. In₂S₃ thin films with different thicknesses in the range, 100–700 nm were deposited on Corning glass substrates at a constant substrate temperature of 300 °C. The films were polycrystalline exhibiting strong crystallographic orientation along the (103) plane. The deposited films showed mixed phases of both cubic and tetragonal structures up to a thickness of 300 nm. On further increasing the film thickness, the layers showed only tetragonal phase. With increase of film thickness, both the crystallite size and surface roughness in the films were found to be increased. The optical constants such as refractive index and extinction coefficient of the as-grown layers have been calculated from the optical transmittance data in the wavelength range, 300–2500 nm. The optical transmittance of the films was decreased from 82% to 64% and the band gap varied in the range, 2.65–2.31 eV with increase of film thickness. The electrical resistivity as well as the activation energy was evaluated and found to decrease with film thickness. The detailed study of these results was presented and discussed.     

Evaluation of an indigenously manufactured Garfilm-EM—250 μm thick polyester film as a dosimeter for high-dose applications

Dosimetric characteristics of indigenously manufactured ‘Garfilm-EM’—a 250 μm thick polyester film—were evaluated spectrophotometrically for its possible application as a routine film dosimeter in gamma radiation processing. Available commercially in large batches, this film is cheap, has a good clarity, consistent thickness, is scratch resistant and is easy to handle. Radiation-induced changes in the absorption spectra of Garfilm were analysed and based on the results obtained, 340 nm was chosen as the wavelength of absorption measurements. The reproducibility of the response of these films for cobalt-60 gamma rays was found to be within ±2.7% (1σ). In the present study, influence of environmental conditions during irradiation like irradiation temperature, relative humidity, oxygen content and dose rate on dose response of Garfilm were also investigated systematically. From the studies carried out, Garfilm-EM has been found to have a good potential for its use as a dosimeter in the absorbed dose range 20–220 kGy due to its linear dose–response relationship, good pre- and post-irradiation stability and reproducibility.     

Electrochemical modification of poly-aniline films in the presence of guaiacol–sulfonic acid

Poly-aniline (PANI) films when subjected to cyclic voltammetry in the presence of guaiacol–sulfonic acid (GSA) undergo a modification which alters their red–ox activity and extends electroactivity to neutral pH. A plausible mechanism of the modification reaction is discussed. The PANI–GSA film modified electrodes electrocatalyze the oxidation of ascorbic acid (AA) in neutral phosphate buffer (pH 7.4) with ca. 250 mV reduction of the oxidation peak potential.     

Surface characterization and in vitro biocompatibility assessment of photosensitive polyimide films

Polyimide (PI) is a commonly used polymer in microelectronics. Recently, numerous PI-based flexible neural interfaces have been developed for reducing mechanical mismatch between rigid implant and soft neural tissue. Most approaches employ non-photosensitive PI, which has been proven earlier to be biocompatible. However, photosensitive polyimide (PSPI) would simplify device fabrication remarkably, but its biocompatibility has been only sparsely reported. In this study, cytotoxicity of spin-coated PSPI (HD Microsystems PI-2771) and conventional PI (HD Microsystems PI-2525) films were evaluated in vitro using BHK-21 fibroblasts according to the ISO-10993-5 standard. PSPIs were tested as cured at a temperature of 200 °C (PI-2771-200) and 350 °C (PI-2771-350). The PI film surfaces were characterized in terms of their roughness, energy and zeta potential which are hypothesized to affect cell–material interactions. The values of the total surface free energy (SFE), and its polar and dispersive component, were significantly (p < 0.001) greater for the PI-2525 film (SFE: 47.3 mJ/m²) than for the PI-2771-200 (25.6 mJ/m²) or PI-2771-350 films (26.2 mJ/m²). The curing temperature of the PI-2771 had a significant effect on the zeta potential values (p < 0.001), but not on surface energy (p = 0.091) or roughness (p = 0.717). The results from the MTS proliferation assays and live/dead staining revealed that PSPI is almost as non-cytotoxic as conventional PI and polyethylene (negative control). The morphology and spreading of BHK-21 cells were similar on all the PI materials tested. In conclusion, PSPI seems to be a promising biocompatible material, while further studies in vitro and in vivo are needed to clarify the long-term effects.     

Phase behaviour of the ternary system {poly(ε-caprolactone) + carbon dioxide + dichloromethane}

Recently, production of biocompatible and biodegradable polymer microparticles has been a matter of growing interest in pharmaceutical and food areas such as drug or active compounds delivery. To conduct production of microparticles, polymeric particle coating, impregnation of active compounds in polymeric films, the knowledge of phase behaviour involving the biodegradable polymer in supercritical carbon dioxide in the presence of a modifier may be needed to allow developing new industrial applications. In this sense, the aim of this work was to investigate the phase behaviour of the ternary system formed by the biodegradable polymer poly(ε-caprolactone) in (carbon dioxide + dichloromethane). Experimental phase transition (bubble and cloud point) values were obtained by applying the static-synthetic method using a variable-volume view cell over the temperature range of (303 to 343) K and pressures up to 21 MPa, in the CO₂ overall composition range of (25–46) wt%, while polymer concentrations studied were (1, 3, 5, and 7) wt%. For the system investigated, depending on the polymer concentration, vapour–liquid, liquid–liquid, and vapour–liquid–liquid phase transitions were verified.     

Visible light active hydrogen modified (HM)-n-TiO2 thin films for photoelectrochemical splitting of water

Visible light active hydrogen modified n-type titanium oxide (HM-n-TiO₂) thin films were synthesized by thermal oxidation of Ti metal sheet (Alfa Co. 0.25 mm thick) in an electric oven followed by incorporation of hydrogen electrochemically under cathodic polarization at ?1.6 V vs Pt. The photoresponse of the HM-n-TiO₂ was evaluated by measuring the rate of water splitting reaction to hydrogen and oxygen in terms of photocurrent density, J_p. The optimized electric oven-made n-TiO₂ and HM-n-TiO₂ photoelectrodes showed photocurrent densities of 0.2 mA cm^?2 and 1.60 mA cm^?2, respectively, at a measured potential of ?0.4 V vs Pt at illumination intensity of 100 mW cm^?2 from a 150 W xenon lamp. This indicated an eightfold increase in photocurrent density for HM-n-TiO₂ compared to oven-made n-TiO₂ at the same measured electrode potential. The band-gap energy of HM-n-TiO₂ was found to be 2.7 eV compared to 2.82 eV for electric oven-made n-TiO₂ and a mid-gap band at 1.67 eV above the valence band was also observed. The HM-n-TiO₂ thin film photoelectrodes were characterized using photocurrent density under monochromatic light illumination and UV–Vis spectral measurements.