Anionic ring-opening polymerization of silacyclobutane derivatives

Anionic polymerizations of 1,1-dimethylsilacyclobutane, 1,1-diethylsilacyclobutane and 1-methyl-1-phenylsilacyclobutane were investigated. Addition of 5 mol % of butyllithium to a solution of 1,1-dimethylsilacyclobutane in THF-hexane (1 : 1) at −48°C provided poly(1,1-dimethylsilabutane) in 99% yield. M_n and M_w/M_n of the obtained polymer were 2400 and 1.10. This polymerization proceeded with a living nature. M_n increased in proportion as the yield of polymer increased. Addition of the second fresh feed of the monomer to the reaction mixture restarted polymerization of the second monomer at the same rate as in the initial stage. Addition of styrene to the living poly(1,1-dimethylsilabutane) provided a poly(1,1-dimethylsilabutane-b-styrene) block copolymer. It was also found that a polymerization of 1,1-diethylsilacyclobutane in THF-hexane at −48°C showed a living nature. In contrast, a polymerization of 1-methyl-1-phenylsilacyclobutane in THF at −78°C did not show a living nature. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 3207–3216, 1997     

A novel synthesis of polyethers with pendant hydroxyl groups by polyaddition of bis(oxetane)s with bis(phenol)s

The polyaddition of 1,4-bis[(3-ethyl-3-oxetanyl)methoxymethyl]benzene (BEOB) with 3,3′,5,5′-tetrachlorobisphenol A (TCBPA) was examined with or without catalysts. High molecular weight polymer (polymers 1) (M_n = 13,600) with pendant primary hydroxyl groups was obtained in a 99% yield without any gel products when the reaction was performed with 5 mol % of tetraphenylphosphonium bromide as a catalyst in NMP at 160°C for 96 h. However, when the reaction was carried out without a catalyst under the same conditions, a low molecular weight polymer (M_n = 3200) was obtained in a 51% yield. The structure of the resulting polymer was confirmed by IR, ¹H-NMR, and ¹³C-NMR spectra. In this reaction system, it was also found that tetraphenylphosphonium iodide and crown ether complexes such as 18-crown-6 (18-C-6)/KBr and 18-C-6/KI have high catalytic activity. Polyadditions of 1,4-bis[(3-methyl-3-oxetanyl)methoxymethyl]benzene with TCBPA and BEOB with 3,3′,5,5′-tetrabromobisphenol-S were also examined, and corresponding polymers (polymers 2 and 3) were obtained in good yields. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 2781–2790, 1999     

Controlled cationic polymerization of cyclopentadiene with B(C6F5)3 as a coinitiator in the presence of water

The controlled cationic polymerization of cyclopentadiene (CPD) at 20 °C using 1‐(4‐methoxyphenyl)ethanol (1)/B(C₆F₅)₃ initiating system in the presence of fairly large amount of water is reported. The number–average molecular weights of the obtained polymers increased in direct proportion to monomer conversion in agreement with calculated values and were inversely proportional to initiator concentration, while the molecular weight distribution slightly broadened during the polymerization (M_w/M_n ～ 1.15–1.60). ¹H NMR analyses confirmed that the polymerization proceeds via reversible activation of the C? OH bond derived from the initiator to generate the growing cationic species, although some loss of hydroxyl functionality happened in the course of the polymerization. It was also shown that the enchainment in cationic polymerization of CPD was affected by the nature of the solvent(s): for instance, polymers with high regioselectivity ([1,4] up to 70%) were obtained in acetonitrile, whereas lower values (around 60%) were found in CH₂Cl₂/CH₃CN mixtures. Aqueous suspension polymerization of CPD using the same initiating system was successfully performed and allowed to synthesize primarily hydroxyl‐terminated oligomers (F_n = 0.8–0.9) with M_n ≤ 1000 g mol^?1 and broad MWD (M_w/M_n ～ 2.2). © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4734–4747, 2008     

Non‐isocyanate synthesis and application of telechelic polyurethanes via polycondensation of diurethanes obtained from ethylene carbonate and diamines

Aliphatic polyurethanes could be obtained in high yield via a non‐isocyanate method based on the self‐polycondensation of dihydroxyurethanes obtained by the reaction of diamines and ethylene carbonate. The polycondensation under a N₂ atmosphere yielded [6,2]polyurethane with a M_n value of 5300 in 87% yield. Two‐step polycondensation, consisting of the polycondensation under a N₂ atmosphere followed by that under reduced pressure, was effective to improve the yield and the molecular weight up to 90% and 10,000, respectively. Although the second polycondensation step at 180 °C was accompanied by formation of urea groups, this side reaction was relatively suppressed at 150 °C. The resulting polyurethane having hydroxyl groups at both of the end groups was converted to polyurethane methacrylate via a reaction with glycidyl methacrylate, and the polyurethane methacrylate served as a crosslinker for radical polymerization of methyl acrylate. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Stereospecific radical polymerization of fluoroalkyl acrylates

The free‐radical polymerization of 2,2,2‐trifluoroethyl acrylate (TFEA), 1,1,1,3,3,3‐hexafluoro‐2‐propyl acrylate (HFiPA) and perfluoro‐tert‐butyl acrylate (PFtBA) was carried out under various conditions and the stereostructure of the obtained polymers was investigated. Most polymerizations of the three monomers afforded polymers rich in diad syndiotacticity (r) in bulk or in solution; the r‐specificity was higher in the HFiPA and PFtBA polymerization than in the TFEA polymerization. Although the tacticity was nearly independent of reaction temperature during the polymerization of TFEA, the r‐specificity increased by lowering the reaction temperature during the polymerization of the other two monomers. The polymerization stereochemistry was also affected by the reaction solvents including toluene, tetrahydrofuran, and fluoroalcohols. It was noted that the stereochemistry of the polymerization of HFiPA and PFtBA also depended on the monomer concentration, and a lower monomer concentration led to a higher r‐specificity. By optimizing the aforementioned reaction conditions, the poly(HFiPA) having r = 81% (polymerization in tetrahydrofuran at −98 °C at [M]_o = 0.2M) and the poly(PFtBA) having r = 77% (polymerization in toluene at −78 °C at [M]_o = 0.2M) were obtained. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1024–1032, 2000     

Synthesis and modification of new biodegradable copolymers: Serine/glycolic acid based copolymers

Serine/glycolic acid-based biodegradable polymers have been prepared by ring-opening homopolymerization of 3-(O-benzyl)-L -serinylmorpholine-2,5-dione, and ring-opening copolymerization of the morpholine-2,5-dione derivative and L -lactide/ϵ-caprolactone. The homopolymerization was carried out in the melt at 165°C for 3 min using stannous octanoate as the initiator and continued at lower reaction temperatures (130–150°C) for 48 h, using a molar ratio of monomer and initiator of 1000 yielded a polymer of M_n = 4000. The polymer prepared by homopolymerization of the morpholine-2,5-dione derivative was composed of alternating protected serine and glycolic acid residues. Random copolymers of serine and glycolic acid and L -lactic acid/ϵ-caprolactone were synthesized by copolymerization reaction of 3-(O-benzyl)-L -serinylmorpholine-2,5-dione and lactide or ϵ-caprolactone in the melt at 165°C for 3 min and further reaction at 130°C using stannous octanoate as an initiator. The polymers were deprotected and functionalized through the side chain hydroxyl group of serine residues with an acrylate moiety for applications in injectable drug delivery, cell encapsulation. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 1901–1907, 1997     

Thermal polycondensation of sugar fluoride to form highly branched polysaccharide

Sugar fluorides were found to undergo powder‐to‐powder polycondensation without any catalyst at 110–160 °C under vacuum, giving highly branched polysaccharides (Conv. = 40–95%, M_w = 1400–20,000). The cross‐polarized optical microscopy at 110 °C disclosed that the crystal shape of α‐glucosyl fluoride ( FGlc ) was unchanged throughout the polymerization in spite of producing the amorphous polymer ( Poly‐FGlc ). The solid‐state post polymerization of Poly‐FGlc (M_w: 2700) at 180 °C increased the higher molecular weight (M_w: 8900). The product polysaccharide was per‐O‐methylated and subjected to structure analyses. Acid‐hydrolysis, which gave a variety of the partially O‐methylated monosaccharides, suggested that the product polysaccharides had a highly branched structure consisting of all of the possible glycosidic linkages. MALDI‐TOF mass analysis revealed that the 1,6‐anhydride terminal unit was formed and participated to the polymerization. Interestingly, α‐maltosyl fluoride hydrate ( FMal·H ₂ O ) was polymerized at the lower temperature (100 °C) than the anhydrate ( FMal ), which required 160 °C for the polymerization. They produced different structure polymers even from the same monomer. The polymer from the former consisted of the disaccharide‐repeating unit, while the repeating unit of the polymer from the latter was the monosaccharide, which was formed by the acetal exchange reaction. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3851–3860, 2007     

Highly reactive polyisobutylenes via AlCl3OBu2‐coinitiated cationic polymerization of isobutylene: Effect of solvent polarity,temperature, and initiator

The cationic polymerization of isobutylene using 2‐phenyl‐2‐propanol (CumOH)/AlCl₃OBu₂ and H₂O/AlCl₃OBu₂ initiating systems in nonpolar solvents (toluene, n‐hexane) at elevated temperatures (?20 to 30 °C) is reported. With CumOH/AlCl₃OBu₂ initiating system, the reaction proceeded by controlled initiation via CumOH, followed by β‐H abstraction and then irreversible termination, thus, affording polymers (M_n = 1000–2000 g mol^?1) with high content of vinylidene end groups (85–91%), although the monomer conversion was low (≤35%) and polymers exhibited relatively broad molecular weight distribution (MWD; M_w/M_n = 2.3–3.5). H₂O/AlCl₃OBu₂ initiating system induced chain‐transfer dominated cationic polymerization of isobutylene via a selective β‐H abstraction by free base (Bu₂O). Under these conditions, polymers with very high content of desired exo‐olefin terminal groups (89–94%) in high yield (>85%) were obtained in 10 min. It was shown that the molecular weight of polyisobutylenes obtained with H₂O/AlCl₃OBu₂ initiating system could be easily controlled in a range 1000–10,000 g mol^?1 by changing the reaction temperature from ?40 to 30 °C. The MWD was rather broad (M_w/M_n = 2.5–3.5) at low reaction temperatures (from ?40 to 10 °C), but became narrower (M_w/M_n ≤ 2.1) at temperatures higher than 10 °C. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis and rheology of biodegradable poly(glycolic acid) prepared by melt ring‐opening polymerization of glycolide

Ring‐opening polymerization (ROP) of glycolide was studied in melt conditions and in the presence of two different initiators: 1‐dodecanol and 1,4‐butanediol and tin(II) 2‐ethylhexanoate as catalyst. Its subsequent polymerization provided poly(glycolic acid) with controlled molar masses ranging from 2000 to 42,000 g/mol with well‐defined structures characterized by NMR. Their thermal properties were evaluated by DSC analysis, and a glass transition temperature at infinite molar mass (T_g∞) of 44.8 °C was thus calculated. From rheological data, the critical molar mass for entanglement, M_c, was estimated to be near 11,000 g/mol. Furthermore, in situ polymerizations were also performed between the plates of the rheometer within a same temperature range from 210 to 235 °C. The variation of the storage and loss moduli during the polymerization step have been monitored by time sweep oscillatory experiments under an angular frequency ω = 10 rad/s. Finally, the development of an inverse rheological method allowed to calculate the bulk polymerization kinetics in the temperature range 200–230 °C. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1440–1449, 2009     

Anionic polymerization of N,N‐dialkyl‐2‐methylenebut‐3‐enamide: Effect of alkyl substituents on polymerization behavior

Anionic polymerizations of three 1,3‐butadiene derivatives containing different N,N‐dialkyl amide functions, N,N‐diisopropylamide (DiPA), piperidineamide (PiA), and cis‐2,6‐dimethylpiperidineamide (DMPA) were performed under various conditions, and their polymerization behavior was compared with that of N,N‐diethylamide analogue (DEA), which was previously reported. When polymerization of DiPA was performed at ?78 °C with potassium counter ion, only trace amounts of oligomers were formed, whereas polymers with a narrow molecular weight distribution were obtained in moderate yield when DiPA was polymerized at 0 °C in the presence of LiCl. Decrease in molecular weight and broadening of molecular weight distribution were observed when polymerization was performed at a higher temperature of 20 °C, presumably because of the effect of ceiling temperature. In the case of DMPA, no polymer was formed at 0 °C and polymers with relatively broad molecular weight distributions (M_w/M_n = 1.2) were obtained at 20 °C. The polymerization rate of PiA was much faster than that of the other monomers, and poly(PiA) was obtained in high yield even at ?78 °C in 24 h. The microstructure of the resulting polymers were exclusively 1,4‐ for poly(DMPA), whereas 20–30% of the 1,2‐structure was contained in poly(DiPA) and poly(PiA). © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3714–3721, 2010     

Cationic polymerization behavior of seven-membered cyclic sulfite

Cationic ring-opening polymerization behavior of a seven-membered cyclic sulfite ( 1 ) was examined. 1 was prepared by the reaction of 1,4-butanediol with SOCl₂ in 58% yield. The cationic polymerization of 1 was carried out at 0, 25, 60, or 100°C with trifluoromethanesulfonic acid (TfOH), methyl trifluoromethanesulfonate (TfOMe), BF₃ · OEt₂, SnCl₄, methyl p-toluenesulfonate (TsOMe), or MeI as an initiator in bulk under a nitrogen atmosphere to afford the polymer with M̄_n 1000–10,400. The order of activities of the initiators for 1 was as follows, TfOH ≅ TfOMe > SnCl₄ > BF₃ · OEt₂ > TsOMe ≅ MeI. The polymerization of 1 with TfOMe afforded a poly(sulfite) below 25°C, but afforded a polymer containing an ether unit at 60°C, which was formed by a desulfoxylation. The higher the activity of the initiator was, the more easily the desulfoxylation occurred. We expected volume expansion on polymerization because cyclic sulfites have large dipole moment values, but it turned out that 1 showed 4.34% shrinkage on polymerization. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 3673–3682, 1997     

Synthesis and characterization of new AB-type poly(etherimide)s containing bisphenol moieties

A series of new AB-type poly(etherimide)s having bisphenol-type moiety was prepared by the one-pot polyimidization using triphenylphosphite(TPP) in N-methyl-2-pyrrolidone(NMP)/pyridine solution at 150°C. Complete cyclodehydration was observed in the polymerizations as well as in model reactions. Polymers were obtained with inherent viscosities in the 0.27–0.49 dL/g range. The M_n and M_w/M_n of poly[4-(1,4-phenyleneoxy-1,4-phenylenehexafluoro-isopropylidene-1,4-phenylene)oxyphthalimide] (4d) with η_inh = 0.49 dL/g were 73,400 g/mol and 1.5, respectively. Most polymers could readily be dissolved in common organic solvents such as DMAc, NMP, and m-cresol. The polymer 4d was soluble even in chloroform. These polymers had glass transition temperatures between 205 and 235°C, and 5% weight loss temperatures in the range of 511–532°C in nitrogen. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 3530–3536, 1999     

Living/controlled cationic cyclopolymerization of divinyl ether with a cyclic acetal moiety: Synthesis of poly(vinyl ether)s with high glass transition temperature based on incorporation of cyclized main chain and cyclic side chains

Cationic cyclopolymerization of 2‐methyl‐5,5‐bis(vinyloxymethyl)‐1,3‐dioxane ( 1 ), a divinyl ether with a cyclic acetal group, was investigated with the HCl/ZnCl₂ initiating system in toluene and methylene chloride at ?30 °C. The reaction proceeded quantitatively to give gel‐free, soluble polymers in organic solvents. The number‐average molecular weight (M_n) of the polymers increased in direct proportion to monomer conversion, and further increased on addition of a fresh monomer feed to the almost completely polymerized reaction mixture, indicating that the polymerization proceeded in living/controlled manner. The contents of the unreacted vinyl groups in the produced soluble polymers were less than ～3 mol %, and therefore, the degree of cyclization was determined to be ～97%. In contrast, the pendant cyclic acetal groups remained intact in the polymers under the present cationic polymerization conditions. These facts show that cyclopolymerization of 1 almost exclusively occurred and the poly(vinyl ether)s with the cyclized repeating units and cyclic pendant acetal rings were obtained. Glass transition temperature (T_g) and thermal decomposition temperature (T_d) of poly( 1 ) (M_n = 7870, M_w/M_n = 1.57) were found to be 166 and 338 °C, respectively, indicating that poly( 1 ) had high T_g and high thermal stability. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 952–958, 2010     

Polymerization of 1,3‐dienes with functional groups. II. Free‐radical polymerization of N‐(2‐methylene‐3‐butenoyl)piperidine

The free‐radical homopolymerization and copolymerization behavior of N‐(2‐methylene‐3‐butenoyl)piperidine was investigated. When the monomer was heated in bulk at 60 °C for 25 h without an initiator, about 30% of the monomer was consumed by the thermal polymerization and the Diels–Alder reaction. No such side reaction was observed when the polymerization was carried out in a benzene solution with 1 mol % 2,2′‐azobisisobutylonitrile (AIBN) as an initiator. The polymerization rate equation was found to be R_p ∝ [AIBN]^0.507[M]^1.04, and the overall activation energy of polymerization was calculated to be 89.5 kJ/mol. The microstructure of the resulting polymer was exclusively a 1,4‐structure that included both 1,4‐E and 1,4‐Z configurations. The copolymerizations of this monomer with styrene and/or chloroprene as comonomers were carried out in benzene solutions at 60 °C with AIBN as an initiator. In the copolymerization with styrene, the monomer reactivity ratios were r₁ = 6.10 and r₂ = 0.03, and the Q and e values were calculated to be 10.8 and 0.45, respectively. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1545–1552, 2003     

Selective polymerization of functional monomers with Novozym 435

Two novel monomers, ambrettolide epoxide and isopropyl aleuriteate, encompassing functional groups, were obtained in a single step from commercially available materials. Novozym 435 catalyzed ring opening polymerization of ambrettolide epoxide furnished a polymer of M_n = 9.7 kg/mol and PDI = 1.9 while the epoxide groups remained unaffected during the polymerization. Selective polymerization of the primary hydroxyl groups of isopropyl aleuriteate using Novozym 435 was feasible and a polymer with moderate molecular weight (M_n = 5.6 kg/mol, PDI = 3.2) was isolated in moderate yield (43%). Subsequently, copolymerization of isopropyl aleuriteate with ε‐CL in different ratios was performed, resulting in soluble, hydroxy functional polymers with good molecular weights (M_n = 10.4–27.2 kg/mol) in good yield (71–78%). The secondary hydroxy groups in the polymer reacted easily with hexyl isocyanate, showing the potential of isopropyl aleuriteate as a comonomer for the synthesis of functional polyesters. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5968–5978, 2007     

Effect of isomeric pyridine moieties in ethynylstyrene derivatives on their anionic polymerization

The anionic polymerization behaviors of ethynylstyrene derivatives containing isomeric pyridine moieties, 2‐(2‐(4‐vinylphenyl)ethynyl)pyridine ( A ), 3‐(2‐(4‐vinylphenyl)ethynyl)pyridine ( B ), and 4‐(2‐(4‐vinylphenyl)ethynyl)pyridine ( C ), were investigated in the identical conditions. The anionic polymerization of A – C was performed with (diphenylmethyl)potassium (Ph₂CHK) in tetrahydrofuran (THF) at ?78 °C. The polymerization of A proceeded quantitatively at –78 °C for 4 h, and the resulting poly( A ) possessed predictable molecular weights (M_n = 3300–68,500) and narrow molecular weight distributions (MWDs) (M_w/M_n = 1.04–1.11). In contrast, the anionic polymerization of B was not performed at –78 °C for 4 h due to the occurrence of side reactions. The monomer B was quantitatively recovered after the reaction. In the polymerization of C performed at –78 °C for 6 h, observed M_n values of the resulting poly( C ) were in good agreement with calculated molecular weights based on monomer to initiator ratios, but the MWDs were somewhat broad (M_w/M_n = 1.23–1.31). To estimate the reactivity of A and to characterize its living nature, the block copolymerization of A with 2‐vinylpyridine (2VP) and methyl methacrylate (MMA) was performed. The well‐defined block copolymers, poly(2VP)‐b‐poly( A ) and poly( A )‐b‐poly(MMA), were successfully synthesized without any additives. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Biodegradable polymers based on renewable resources. IX. Synthesis and degradation behavior of polycarbonates based on 1,4:3,6‐dianhydrohexitols and tartaric acid derivatives with pendant functional groups

Novel polycarbonates, with pendant functional groups, based on 1,4:3,6‐dianhydrohexitols and L ‐tartaric acid derivatives were synthesized. Solution polycondensations of 1,4:3,6‐dianhydro‐bis‐O‐(p‐nitrophenoxycarbonyl)hexitols and 2,3‐di‐O‐methyl‐L ‐threitol or 2,3‐O‐isopropylidene‐L ‐threitol afforded polycarbonates having pendant methoxy or isopropylidene groups, respectively, with number average molecular weight (M_n) values up to 3.6₁ × 10⁴. Subsequent acid‐catalyzed deprotection of isopropylidene groups gave well‐defined polycarbonates having pendant hydroxyl groups regularly distributed along the polymer chain. Differential scanning calorimetry (DSC) demonstrated that all the polycarbonates were amorphous with glass transition temperatures ranging from 57 to 98 °C. Degradability of the polycarbonates was assessed by hydrolysis test in phosphate buffer solution at 37 °C and by biochemical oxygen demand (BOD) measurements in an activated sludge at 25 °C. In both tests, the polycarbonates with pendant hydroxyl groups were degraded much faster than the polycarbonates with pendant methoxy and isopropylidene groups. It is noteworthy that degradation of the polycarbonates with pendant hydroxyl groups was remarkably fast. They were completely degraded within only 150 min in a phosphate buffer solution and their BOD‐biodegradability reached nearly 70% in an activated sludge after 28 days. The degradation behavior of the polycarbonates is discussed in terms of their chemical and physical properties. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3909–3919, 2005     

Radical polymerization behavior of trimethoxyvinylsilane

Trimethoxyvinylsilane (TMVS) was quantitatively polymerized at 130 °C in bulk, using dicumyl peroxide (DCPO) as initiator. The polymerization of TMVS with DCPO was kinetically studied in dioxane by Fourier transform near‐infrared spectroscopy. The overall activation energy of the bulk polymerization was estimated to be 112 kJ/mol. The initial polymerization rate (R_p) was expressed by R_p = k[DCPO]^0.6[TMVS]^1.0 at 120 °C, being closely similar to that of the conventional radical polymerization involving bimolecular termination. The polymerization system involved electron spin resonance (ESR) spectroscopically observable polymer radicals under the actual polymerization conditions. ESR‐determined apparent rate constants of propagation and termination were 13 L/mol s and 3.1 × 10⁴ L/mol s at 120 °C, respectively. The molecular weight of the resulting poly(TMVS)s was low (M_n = 2.0–4.4 × 10³), because of the high chain transfer constant (C_mtr = 4.2 × 10^?2 at 120 °C) to the monomer. The bulk copolymerization of TMVS (M₁) and vinyl acetate (M₂) at 120 °C gave the following copolymerization parameters: r_l = 1.4, r₂ = 0.24, Q₁ = 0.084, and e₁ = +0.80. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5864–5871, 2005     

The crystal structure of 1,4-benzenedithiol by rietveld analysis and studies on the mechanism of solid-state addition polymerization of 1,4-benzenedithiol to 1,4-diethynylbenzene

The crystal structure of 1,4-benzenedithiol (BDT) was determined by the Rietveld method based on the calculation of the atomic coordinates of the BDT molecule using the Molecular Mechanics Program (MMP2). The refined crystal structure of BDT was monoclinic P₂₁/c with dimensions, a = 7.795, b = 7.290, c = 5.955 Å, β = 92.16°, z = 2. The R factor of the refined structure was 0.038. Using above results, the mechanism of solid-state addition polymerization of BDT to 1,4-diethynylbenzene (DEB) was studied. Sublimed BDT piles up onto glass plate substrate and forms the layer structure along with the a axis. An inclination angle of the piled BDT column was 60° toward the substrate surface. DEB crystal structure was also monoclinic P₂₁/c with a = 4.007, b = 6.018; c = 15.340 Å, β = 91.42°, z = 2. Sublimation of equimolar mixture of BDT and DEB gave a crystal having 1 : 1 composition, in which DEB column is situated between the columns of BDT. Relative arrangement of both monomers was suitable for the addition of  SH and  CCH groups, since the distance between the two groups is 3.3 Å by CERIUS II calculation. Therefore, the addition polymerization of BDT to DEB easily proceeded by UV irradiation and the resulting polymer had a highly layer structure along with the a axis of BDT crystal. Tentatively estimated crystal structure of polymer obtained is monoclinic with a = 7.73, b = 7.30, c = 5.95 Å, β = 92.16°. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 1621–1625, 1997     

(Diisopropylamido) bis (methylcyclopentadienyl) lanthanides as single-component initiators for polymerization of methyl methacrylate

It was first found that (diisopropylamido)bis(methylcyclopentadienyl)lanthanides (MeC₅H₄)₂LnN(i-Pr)₂(THF) (Ln = Yb ( 1 ), Er ( 2 ), Y ( 3 )) exhibit extremely high catalytic activity in the polymerization of methyl methacrylate. The reactions can be carried out over a quite broad range of polymerization temperatures from -78 to 40°C. The catalytic activity of the complexes increases with an increase of ionic radii of the metal elements, i.e. Y > Er > Yb. The results of GPC (gel permeation chromatography) indicate that the number-average molecular weights (M_n) of polymers obtained exceed 100 × 10³ and the molecular weight distribution (M_w/M_n) becomes broad with the increase of temperature. Furthermore highly syndiotactic PMMA (87.7%) can be obtained by lowering the reaction temperature to −78°C. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1593–1597, 1998