Hydrophilic segmented block copolymers based on poly(ethylene oxide) and monodisperse amide segments

Segmented block copolymers based on poly(ethylene oxide) (PEO) flexible segments and monodisperse crystallizable bisester tetra‐amide segments were made via a polycondensation reaction. The molecular weight of the PEO segments varied from 600 to 4600 g/mol and a bisester tetra‐amide segment (T6T6T) based on dimethyl terephthalate (T) and hexamethylenediamine (6) was used. The resulting copolymers were melt‐processable and transparent. The crystallinity of the copolymers was investigated by differential scanning calorimetry (DSC) and Fourier Transform infrared (FTIR). The thermal properties were studied by DSC, temperature modulated synchrotron small angle X‐ray scattering (SAXS), and dynamic mechanical analysis (DMA). The elastic properties were evaluated by compression set (CS) test. The crystallinity of the T6T6T segments in the copolymers was high (>84%) and the crystallization fast due to the use of monodisperse tetra‐amide segments. DMA experiments showed that the materials had a low T_g, a broad and almost temperature independent rubbery plateau and a sharp flow temperature. With increasing PEO length both the PEO melting temperature and the PEO crystallinity increased. When the PEO segment length was longer than 2000 g/mol the PEO melting temperature was above room temperature and this resulted in a higher modulus and in higher compression set values at room temperature. The properties of PEO‐T6T6T copolymers were compared with similar poly(propylene oxide) and poly(tetramethylene oxide) copolymers. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4522–4535, 2007     

Regularity modes in Raman spectra of polyolefins: Part II. Polyethylene and ethylene copolymers

In this work, the thermal behavior of the regularity modes in Raman spectra of polyethylene with different densities and random ethylene/1-hexene copolymers with varying content of comonomer are studied. We demonstrate especially that the vibrational modes at 1062 and 2850 cm^↙1 are related to a critical sequence length of trans-conformers of 6⬜8 CH₂ groups, while the modes at 1130, 1170, 1295, and 2883 cm^↙1 indicate a critical sequence length of trans-conformers of 18 CH₂ groups. Upon increasing the 1-hexene content in the ethylene/1-hexene copolymers, the evolution of the intensities of the Raman modes at 1062, 1130, 1170, 1295, and 1417 cm^↙1, normalized to the intensity of the band at 2850 cm^↙1, is similar to the evolution of the intensities of the same modes in the Raman spectra of low density polyethylene at increasing temperature. This observation however contrasts with that in the Raman spectra of polyethylenes with middle and high densities. We suppose that these results can be explained by similarities in the structure of non-crystalline areas of low density polyethylene and the ethylene/1-hexene copolymers, which contain significant amounts of short sequences of trans-conformers.     

The effect of residual acetate groups on the structure and properties of vinyl alcohol–ethylene copolymers

Vinyl alcohol–ethylene (VAE) copolymers, commercially manufactured by hydrolysis of the corresponding vinyl acetate–ethylene copolymers, can contain small amounts of unhydrolyzed vinyl acetate. This article shows the influence of these residual groups on the structure of the resulting copolymers, studied by nuclear magnetic resonance and wide‐angle X‐ray scattering. Thermal and mechanical properties of these materials were investigated by differential scanning calorimetry, thermogravimetry, drawing behavior, birefringence measurements, and dynamic mechanical analysis. The structure of the copolymers is considerably affected by the volume of the residual acetate groups, bigger than that of the hydroxyl ones, which hinders the crystallization process. In relation to the thermal and mechanical properties, the temperature and enthalpy of melting as well as the Young's modulus and yield stress, decrease as vinyl acetate molar fraction increases. Moreover, the α and β relaxations are shifted to lower temperatures as residual content in the copolymer is raised. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 573–583, 2000     

Modeling molecular weight distribution of comb-branched graft copolymers

Grafting one type polymer onto a different polymer type may yield a comb-branched copolymer. The branching density has a significant effect on its overall molecular weight distribution. A general model is derived to describe the bivariate distribution of molecular weight and branching density for such comb copolymers. The model is applicable for various grafting mechanisms provided the side chains are randomly grafted onto the backbone. The determining parameters are the molecular weight distributions of backbone and side chains, and the branching density. Analytical expressions are obtained for the cases of the side chains having uniform and Schulz–Zimm distributions. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 705–714, 1998     

Segmented block copolymers of poly(ethylene glycol) and poly(ethylene terephthalate)

A new series of segmented copolymers were synthesized from poly(ethylene terephthalate) (PET) oligomers and poly(ethylene glycol) (PEG) by a two‐step solution polymerization reaction. PET oligomers were obtained by glycolysis depolymerization. Structural features were defined by infrared and nuclear magnetic resonance (NMR) spectroscopy. The copolymer composition was calculated via ¹H NMR spectroscopy. The content of soft PEG segments was higher than that of hard PET segments. A single glass‐transition temperature was detected for all the synthesized segmented copolymers. This observation was found to be independent of the initial PET‐to‐PEG molar ratio. The molar masses of the copolymers were determined by gel permeation chromatography (GPC). © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4448–4457, 2004     

星形聚氧乙烯及星形杂臂氧化乙烯-苯乙烯共聚物的合成

以原子转移自由基偶联法合成了多臂星形聚合物S-PEO和星形杂臂共聚物PEO-PS。以傅立叶红外光谱(FT-IR)和核磁共振(1H NMR)分析方法确定了产物的结构。以GPC分析测试了产物的分子量和分子量分布。GPC分析结果表明所得聚合物分子量增大,分子量分布窄,偶联反应效率可高达99%以上。     

The effect of annealing on the structure and relaxation processes of vinyl alcohol–ethylene copolymers

An annealing process has been applied to three samples of vinyl alcohol–ethylene (VAE) copolymers, richer in the former comonomer. The effect of such a process on the structure and on the relaxation mechanisms is studied. The structure of the three VAE copolymers has changed slightly. Nevertheless, the viscoelastic relaxation processes have been significantly affected for the thermal treatment. Two additional relaxations have appeared: one of them at temperatures above the relaxation associated to the glass transition, and the other at temperatures below the β mechanism of these copolymers. The temperature location, intensity, and apparent activation energy of the distinct relaxations found are discussed and compared with those in the original copolymers and the homopolymers, poly(vinyl alcohol) and polyethylene. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 1–12, 2001     

Synthesis and study of water-soluble chitosan-O-poly(ethylene glycol) graft copolymers

Novel chitosan-O-poly(ethylene glycol) graft copolymers were synthesized. Etherification of N-phthaloyl chitosan by poly(ethylene glycol) monomethyl ether (MPEG) iodide was carried out in dimethylformamide in the presence of silver oxide. Varying the ratio of MPEG iodide to chitosan, different degree of O-substitution of MPEG to monosaccharide residue of chitosan (5-197%) was obtained. Chemical structure of the new chitosan derivatives was confirmed using FTIR spectroscopy and analysis of functional groups. O-PEGylated chitosans are soluble in water and aqueous solutions of wide pH range. Reduced viscosity of aqueous solutions of the graft copolymers is extremely low and similar to that of MPEG-2000.     

Gamma irradiation effect upon positron annihilation in ultra high molecular weight poly(ethylene oxide)

Positron annihilation technique was used to reveal the evolution of small pore structure of semi-crystalline ultra high molecular weight poly(ethylene oxide) under γ-irradiation. It has been established that the structure of poly(ethylene oxide) is improved under low dose irradiation (<20 kGy), while the concentration of free-volume holes in amorphous regions increases at higher doses. The results were compared with those from small angle X-ray scattering and wide angle X-ray scattering measurements of the same samples.     

Influence of crystallite structure of nanometer TiO_2 catalysts on photocatalyst reaction

25 samples of nanometer TiO2 were prepared through modifying the preparation conditions including the concentrations of Ti(SO4)2 and NH4HCO3, the pH value at the end of precipitation operation, and sintering temperature and time by methods of orthogonal design. The relationships between their catalytic activities of photocatalytic degradation of sodium dodecyl benzene sulfonate (SDBS) and the normal crystallite size, lattice-strain and X-ray diffraction intensity of 10 crystal faces were analyzed. It was discovered that the photocatalytic degradation reaction of SDBS follows first-order kinetics. Crystal faces of catalysts' (101) have greater influence than other crystal faces on the reaction. The photocatalytic reaction needs more perfect (101) crystal faces with less lattice-strain. Smaller normal crystallite size and greater specific surface area of (101) crystal face are better for increasing reaction rate. The photocatalytic reaction is mainly proceeded on the (101) crystal face, comparatively, amor     

Synthesis and characterization of anionic graft copolymers containing poly(ethylene oxide) grafts

Anionic graft copolymers were synthesized through grafting of poly(ethylene glycol) monomethyl ether (MPEG) onto terpolymers containing succicinic anhydride groups. The backbone polymers were prepared through radical terpolymerization of maleic anhydride, styrene, and one of the following monomers: methyl methacrylate, ethylhexyl methacrylate, and diethyl fumarate. MPEG of different molecular weights were grafted onto the backbone through reactions with the cyclic anhydride groups. In this reaction one carboxylic acid group is formed together with each ester bond. The molecular weights of MPEG were found to influence the rate of the grafting reaction and the final degree of conversion. The graft copolymers were characterized by IR, GPC, and ¹H-NMR. Thermal properties were examined by DSC. Graft copolymers containing 50% w/w of MPEG 2000 grafts were found to be almost completely amorphous, presumably because of crosslinking, and hydrogen bonding between carboxylic acid groups in the backbone and the ether oxygens in MPEG grafts. © 1995 John Wiley & Sons, Inc.     

Chitosan-N-poly(ethylene glycol) brush copolymers: Synthesis and adsorption on silica surface

Chitosan-N-poly(ethylene glycol) brush copolymers with different degree of substitution (DS) were synthesized via reductive amination of chitosan by methoxy poly(ethylene glycol) (MPEG) aldehyde. Chitosan-N-MPEG copolymers were high-molecular-weight products with desirable DS; solubility and solution viscosity of those copolymers depended on the method of the synthesis of MPEG aldehyde and on DS. Synthesis of MPEG aldehyde by the use of TEMPO radical/BAIB was not suitable because of partial oxidation of methoxy groups of MPEG resulting in bifunctional PEG derivatives leading to cross-linking. Adsorption studies of chitosan-N-MPEG graft copolymers on silica surface show that these polymers adsorb in highly hydrated layers.     

Influence of molecular weight on the microhardness of poly(ethylene terephthalate)

 Poly(ethylene terephthalate) (PET) was annealed in vacuum at different temperatures (190–260 °C) for different times (10 min–24 h) in order to examine the mechanical properties (microhardness) of PET samples with a wide range of molecular weights (10 000–120 000). Short annealing times result in a twofold decrease in mol. wt. due to hydrolytic decomposition. However, long annealing times give rise to a substantial molecular weight increase. It is found that microhardness (H) rises linearly with the degree of crystallinity obtained during up-grading of mol. wt. and its extrapolation leads to H-values of completely crystalline PET, H ^PET _c=405 MPa for samples with conventional mol. wt. and of 426 MPa for samples with mol. wt. higher than 30 000. It is shown that the increase of mol. wt. for each set of samples with a given range of degree of crystallinity also causes a slight increase of H. The influence of mol. wt. upon hardness is discussed in the light of the changes in the physical structure (crystallinity, crystal thickness) which is formed at given heat treatment conditions. Received: 29 April 1997 Accepted: 23 September 1997     

Discrimination of ethylene/vinyl acetate copolymers with different composition and prediction of the content of vinyl acetate in the copolymers and their melting points by near-infrared spectroscopy and chemometrics

Near-infrared (NIR) diffuse reflectance spectra have been measured by use of a rotating drawer for pellets of 12 kinds of ethylene/vinyl acetate (EVA) copolymers with vinyl acetate (VA, the comonomer) varying in the 7–44 wt % range. They are unambiguously discriminated from one another by a score plot of the principal component analysis (PCA) Factor 1 and 2, based upon the NIR spectra pretreated by multiplicative scatter correction (MSC). Principal component (PC) weight loadings for Factor 1 show that the discrimination relies largely upon bands due to the overtone and combination modes arising from the VA unit. We have found one “outlier” in the score plot and elucidated its spectral characteristics based upon PC weight loadings for Factor 2. Partial least-squares (PLS) regression has been applied to propose calibration models which predict the VA content in EVA. The models have been prepared for three kinds of pretreatment, the first derivative, the second derivative, and MSC; and four kinds of wavelength regions. The NIR spectra in the 1100–2200 nm region after the MSC treatment has given the best correlation coefficient and standard error of prediction (SEP) of 0.998 and 0.70%, respectively. The calibration models, prepared by NIR diffuse reflectance spectroscopy for the pellet samples, are compared with previously reported models by NIR transmission spectroscopy for the flowing molten samples, and with those by Raman spectroscopy for the pellet samples. PLS regression has also allowed us to predict melting points of the copolymers with the correlation coefficient and SEP of 0.997 and 0.78°C, respectively. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 1529–1537, 1998     

Synthesis of AB(BA), ABA and BAB block copolymers of tert-butyl methacrylate (A) and ethylene oxide (B)

Well-defined AB(BA), ABA, and BAB block copolymers of tert-butyl methacrylate (tBMA) (A) and ethylene oxide (EO) (B) have been prepared by sequential living anionic polymerization of the two comonomers, irrespective of their addition order. Diphenyl methyl potassium and naphthalene potassium have been successfully used as mono- and difunctional initiators, respectively. In all cases, molecular weight and composition of the block copolymers can be predicted on the basis of the monomer over initiator molar ratio, and the molecular weight distribution is relatively narrow. Size exclusion chromatography, selective extractions of homopolymers, and ¹H- and ¹³C-NMR spectroscopy support that block copolymerization proceeds without homopolymer formation nor side reactions, e.g., transesterification reactions. The PtBMA blocks have been quantitatively hydrolyzed into polyacid ones with formation of polyacid-b-polyether block copolymers as supported by titration, ¹H-NMR, and IR analysis. © 1992 John Wiley & Sons, Inc.     

Self-diffusion study of poly (ethylene oxide)-poly (propylene oxide)-poly (ethylene oxide) block copolymers in aqueous solution

The self-diffusion of poly (ethylene oxide)-poly (propylene oxide)-poly (ethylene oxide) block copolymers dissolved in deuterated water was investigated by means of pulsed field gradient NMR (PFG-NMR). The polymer forms micelles in the solution and, with increasing temperature, clouding and phase demixing occurs. The self-diffusion coefficient indicates the association of the polymer molecules in the vicinity of the cloud point because of its maximum with increasing temperature. Above the cloud point, two kinds of diffusing species are observed due to phase separation. The faster diffusing species is attributed to the polymer-poor phase. The self-diffusion coefficient of the polymer-rich phase species decreases with increasing temperature above the cloud point due to further association and dehydration. The correlation length of the diffusing associates, calculated from the self-diffusion coefficient and the viscosity by means of the Stokes-Einstein equation is nearly independent of temperature and concentration up to 30 wt-% polymer concentration. The correlation length is about 1.4 nm. It shows a slight maximum at the cloud point.     

Influence of crystallite structure of nanometer TiO2 catalysts on photocatalyst reaction

25 samples of nanometer TiO₂ were prepared through modifying the preparation conditions including the concentrations of Ti(SO₄)₂ and NH₄HCO₃, the pH value at the end of precipitation operation, and sintering temperature and time by methods of orthogonal design. The relationships between their catalytic activities of photocatalytic degradation of sodium dodecyl benzene sulfonate (SDBS) and the normal crystallite size, lattice-strain and X-ray diffraction intensity of 10 crystal faces were analyzed. It was discovered that the photocatalytic degradation reaction of SDBS follows first-order kinetics. Crystal faces of catalysts’ (101) have greater influence than other crystal faces on the reaction. The photocatalytic reaction needs more perfect (101) crystal faces with less lattice-strain. Smaller normal crystallite size and greater specific surface area of (101) crystal face are better for increasing reaction rate. The photocatalytic reaction is mainly proceeded on the (101) crystal face, comparatively, amorphous TiO₂ has lower catalytic activity.     

CO2 permeation properties of poly(ethylene oxide)-based segmented block copolymers

This paper discusses the gas permeation properties of poly(ethylene oxide) (PEO)-based segmented block copolymers containing monodisperse amide segments. These monodisperse segments give rise to a well phase-separated morphology, comprising a continuous PEO phase with dispersed crystallised amide segments. The influence of the polyether phase composition and of the temperature on the permeation properties of various gases (i.e., CO₂, N₂, He, CH₄, O₂ and H₂) as well as on the pure gas selectivities were studied in the temperature range of −5 °C to 75 °C. The CO₂ permeability increased strongly with PEO concentration, and this effect could partly be explained by the dispersed hard segment concentration and partly by the changing chain flexibility. By decreasing the PEO melting temperature the low temperature permeabilities were improved. The gas transport values were dependant on both the dispersed hard segment concentration and the polyether segment length (length between crosslinks). The gas selectivities were dependant on the polyether segment length and thus the chain flexibility.     

Diblock copolymers as emulsifying agents in polymer blends: Influence of molecular weight,architecture, and chemical composition

Interfacial agents used in the compatibilization of immiscible polymer blends often consist of block copolymers containing at least one segment compatible with each of the two phases of the blend. This work examines the influence of the molecular weight, architecture, and chemical composition of the interfacial agent on its ability to emulsify a polymer blend. The system chosen is a blend containing 80% polystyrene and 20% ethylene-propylene rubber, compatibilized by diblock copolymers of poly(styrene-hydrogenated butadiene). The emulsification curve, which relates the dispersed phase particle size to the concentration of interfacial agent added to the system, was used as a tool to characterize the efficacy of the different interfacial agents. The observed behavior is similar to that of classical emulsions: a rapid drop in phase size at low concentrations of interfacial modifier, followed by a levelling off to an equilibrium diameter value once a “critical” concentration has been reached. For systems compatibilized by symmetrical diblocks (i.e., containing approximately 50% styrene by weight), the volume average particle diameter decreased from 2.7 μm for the unmodified system to about 0.4 μm once interfacial saturation is reached. The critical concentration for emulsification decreased with increasing interfacial agent molecular weight, due to the higher interfacial area occupied by longer molecules; however, this parameter did not affect the equilibrium particle diameter. The asymmetrical diblock copolymer (30% styrene) was found to be less effective than the symmetrical ones over the entire range of concentrations studied (5 to 35% modifier, based on the volume of the minor phase). Asymmetrical diblock copolymers would tend to form micelles, whereas symmetrical copolymers are less constrained at the interface. No significant difference was observed between the emulsifying capability of tapered and pure diblocks of similar composition and molecular weight. © 1996 John Wiley & Sons, Inc.     

Thermoreversible gelation of poly(ethylene oxide) biodegradable polyester block copolymers. II

Poly(ethylene oxide)-b-poly(L-lactic acid) (PEO-PLLA) diblock copolymers were synthesized via a ring opening polymerization from poly(ethylene oxide) and l -lactide. Stannous octoate was used as a catalyst in a solution polymerization with toluene as the solvent. Their physicochemical properties were investigated by using infrared spectroscopy, ¹H-NMR spectroscopy, gel permeation chromatography, and differential scanning calorimetry, as well as the observational data of gel-sol transitions in aqueous solutions. Aqueous solutions of PEO-PLLA diblock copolymers changed from a gel phase to a sol phase with increasing temperature when their polymer concentrations are above a critical gel concentration. As the PLLA block length increased, the gel-sol transition temperature increased. For comparison, diblock copolymers of poly(ethylene oxide)-b-poly(l -lactic acid-co-glycolic acid) [PEO-P(LLA/GA)] and poly(ethylene oxide)-b-poly(dl -lactic acid-co-glycolic acid) [PEO-P(DLLA/GA)] were synthesized by the same methods, and their gel-sol transition behaviors were also investigated. The gel-sol transition properties of these diblock copolymers are influenced by the hydrophilic/hydrophobic balance of the copolymer, block length, hydrophobicity, and stereoregularity of the hydrophobic block of the copolymer. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 2207–2218, 1999