Preparation of conductive,flexible and transparent films by in situ deposition of polypyrrole nanoparticles on polyethylene terephthalate

In this study polypyrrole (PPy) nanoparticles were deposited as a thin film on the modified surface of polyethyleneterephthalate (PET) by in situ chemical polymerization in the presence of sodium dodecylsulfate (SDS), sodium dodecylbenzenesulfonate (DBSNa) and mixture of them as the surfactant. The surface of PET was modified by KOH before deposition and was investigated for conductivity and adhesion of PPy nanoparticles to PET. Resulting conductive flexible films were characterized by UV–Vis spectroscopy, fieldemission scanning electron microscopy, contact angle measurements and four-point-probe technique for conductivity. Direct morphological observation (FESEM) and electrical measurements indicated that the morphology, conductivity and the nature of deposited PPy films depend on surfactant, surface modification of PET and monomer concentration. In optimized process condition, uniform conductive films of PPy were obtained with good adhesion to PET.     

Novel UV‐induced photografting process for preparing poly(tetrafluoroethylene)‐based proton‐conducting membranes

A novel process comprising the UV‐induced photografting of styrene into poly(tetrafluoroethylene) (PTFE) films and subsequent sulfonation has been developed for preparing proton‐conducting membranes. Although under UV irradiation the initial radicals were mainly generated on the surface of the PTFE films by the action of photosensitizers such as xanthone and benzoyl peroxide, the graft chains were readily propagated into the PTFE films. The sulfonation of the grafted films was performed in a chlorosulfonic acid solution. Fourier transform infrared and scanning electron microscopy were used to characterize the grafted and sulfonated membranes. With a view to use in fuel cells, the proton conductivity, water uptake, and mechanical properties of the prepared membranes were measured. Even through the degree of grafting was lower than 10%, the proton conductivity in the thickness direction of the newly prepared membranes could reach a value similar to that of a Nafion membrane. In comparison with γ‐ray radiation grafting, UV‐induced photografting is very simple and safe and is less damaging to the membranes because significant degradation of the PTFE main chains can be avoided. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2624–2637, 2007     

Gas transport in surface grafted polypropylene films with poly(acrylic acid) chains

This work describes the grafting reaction of poly(acrylic acid) (PA) onto the surface of polypropylene (PP) films carried out with ultraviolet radiation, using benzophenone as photoinitiator and water as solvent. By increasing the reaction time, graft percentages of 3.5, 6.5, 12.9, 19.8, 29.4, and 36.0% were obtained. Micrographs of the modified films show that grafting exclusively occurs on the PP films surface. The values of the permeability coefficient of oxygen, nitrogen, carbon dioxide, carbon monoxide, argon, methane, ethane, ethylene, and propane across the grafted films undergo a sharp drop. The interpretation of the permeation results suggest that radicals created in the tertiary carbons of the grafted chains by effect of UV light or by chain transfer reactions may highly crosslink the PA grafted layer. A rigid layer involving both strong hydrogen bonding and chains crosslinking is formed at grafting percentages of 3.5% that strongly hinders gas permeation across that layer. Destruction of hydrogen bonding by partially replacing protons of acrylic acid residues by sodium/silver cations increases the permeability of the surface grafted films. Finally, the films permselectivity is hardly affected by the grafted layer. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2421–2431, 2007     

Surface modification of poly(tetrafluoroethylene) films by plasma polymerization of glycidyl methacrylate and its relevance to the electroless deposition of copper

Surface modification of poly(tetrafluoroethylene) films by plasma polymerization and deposition of glycidyl methacrylate (GMA) was carried out. The effects of glow‐discharge conditions on the chemical structure and composition of the deposited GMA polymer were analyzed by X‐ray photoelectron spectroscopy (XPS) and Fourier transform infrared (FTIR) spectroscopy. XPS and FTIR results revealed that the epoxide groups in the plasma‐polymerized GMA (pp‐GMA) layer had been preserved to various extents, depending on the plasma deposition conditions. The morphology of the modified PTFE surface was investigated by atomic force microscopy (AFM). The pp‐GMA film with well‐preserved epoxide groups was used as an adhesion promotion layer to enhance the adhesion of the electrolessly deposited copper on the PTFE film. The T‐peel adhesion test results showed that the adhesion strength between the electrolessly deposited copper and the pp‐GMA‐modified PTFE (pp‐GMA‐PTFE) film was much higher than that between the electrolessly deposited copper and the pristine or the Ar plasma‐treated PTFE film. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3498–3509, 2000     

Reactive adsorption of aminosilane onto the glycidyl methacrylate graft‐copolymerized poly(tetrafluoroethylene) film surface for adhesion enhancement with evaporated copper

Surface modification of argon‐plasma‐pretreated poly(tetrafluoroethylene) (PTFE) film via UV‐induced graft copolymerization with glycidyl methacrylate (GMA) was carried out first. Reactive adsorption of γ‐aminopropyltriethoxysilane (APS) onto the GMA graft‐copolymerized PTFE (GMA‐g‐PTFE) film surface was performed by the simple immersion of the film in the APS solution. The adsorption process was studied as a function of the APS concentration, the immersion time of the graft‐modified PTFE film in the APS solution, and the washing protocol. The chemical composition and morphology of the silane‐modified surfaces were characterized by X‐ray photoelectron spectroscopy and atomic force microscopy, respectively. The performance of the silane‐modified PTFE surface in adhesion promotion was investigated. The T‐peel adhesion strength of the evaporated Cu on the PTFE film with the reactively adsorbed organosilane increased significantly to about 12.5 N/cm. This adhesion strength was more than twice that of the assembly involving evaporated Cu on the GMA‐g‐PTFE film and about 10 times that of the assembly involving evaporated Cu on the Ar‐plasma‐treated PTFE film. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 80–89, 2000     

Surface modification of poly(tetrafluoroethylene) by a low-temperature cascade arc torch and radio-frequency plasmas

Poly(tetrafluoroethylene) (PTFE) films were treated with a low-temperature cascade arc torch (LTCAT) and radio-frequency (RF) plasmas of argon and hydrogen. The plasma-treatment effect on the PTFE surface was studied with contact-angle measurement and scanning electron spectroscopy (SEM). LTCAT argon plasma, which is recognized as a beam of excited argon neutrals, was very efficient at improving the surface hydrophilicity of PTFE. For both the LTCAT and RF operation, argon plasma was more effective at modifying the surface wettability of PTFE films than hydrogen plasma was. Furthermore, the sample positions (inside or beyond the glow region) had a strong impact on the efficiency of the plasma treatment. SEM surface images indicated that no significant morphology change was induced on the PTFE films exposed to a LTCAT and RF argon plasmas. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 4432–4441, 1999     

Enhanced photoinduced super-hydrophilicity in sol–gel TiO2 thin films with co-doped Sn/Nb

In this work, Sn and Nb co-doped TiO₂ were coated on glazed porcelain substrates via sol–gel dip coating method. Field emission-scanning electron microscopy, transmission electron microscopy, and UV–vis spectrophotometer were used to evaluate thickness and optical properties of the thin films. Surface chemical state of thin films was examined by atomic X-ray photoelectron spectroscopy. Water contact angle on the film surfaces was measured by a contact angle analyzer under solar light irradiation. The optical results indicated that Sn/Nb dopant in TiO₂ thin film changed the absorption edge from ultraviolet to visible light and exhibited excellent photo-catalytic ability for degradation of methylene blue solution under solar irradiation. Wettability results indicated that Sn and Nb dopant ions had significant effect on the hydrophilicity property of thin films.     

Surface‐initiated atom transfer radical polymerization from porous poly(tetrafluoroethylene) membranes using the C?F groups as initiators

This work reports the surface‐initiated atom transfer radical polymerization (ATRP) from hydrogen plasma‐treated porous poly(tetrafluoroethylene) (PTFE) membranes using the C? F groups as initiators. Hydrogen plasma treatment on PTFE membrane surfaces changes their chemical environment through defluorination and hydrogenation reactions. With the hydrogen plasma treatment, the C? F groups of the modified PTFE membrane surface become effective initiators of ATRP. Surface‐initiated ATRP of poly(ethylene glycol) methacrylate (PEGMA) is carried out to graft PPEGMA chains to PTFE membrane surfaces. The chain lengths of poly(PEGMA) (PPEGMA) grafted on PTFE surfaces increase with increasing the reaction time of ATRP. Furthermore, the chain ends of PPEGMA grown on PTFE membrane surfaces then serve as macroinitiators for the ATRP of N‐isopropylacrylamide (NIPAAm) to build up the PPEGMA‐b‐PNIPAAm block copolymer chains on the PTFE membrane surfaces. The chemical structures of the modified PTFE membranes are characterized using X‐ray photoelectron spectroscopy. The modification increases the surface hydrophilicity of the PTFE membranes with reductions in their water‐contact angles from 120° to 60°. The modified PTFE membranes also show temperature‐responsive properties and protein repulsion features owing to the presence of PNIPAAM and PPEGMA chains. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2076–2083, 2010     

Direct-current discharge treatment of polytetrafluoroethylene films

The effect of treatment in a low-pressure dc discharge on the surface properties of polytetrafluoroethylene (PTFE) films modified at the anode and cathode was examined. It was found that the anode treatment of the films considerably improves the adhesive properties of the polymer and makes it possible to obtain substantially lower values of the contact angle and higher values of the work of adhesion and surface energy than in the case of other PTFE surface modification techniques. By means of IR and X-ray photoelectron spectroscopy, it was shown that discharge treatment at the anode and cathode noticeably increases the amount of oxygen-containing groups on the surface of the films.     

聚氨酯微球的接枝改性及温敏特性

以N-异丙基丙烯酰胺(NIPAAm)为单体, 二苯甲酮(BP)为光敏剂, 过硫酸胺(APS)为自由基引发剂, 采用溶液中光接枝方法制备了具有温度敏感特性的聚氨酯微球(PUS). 傅里叶变换红外光谱(FTIR)和扫描电子显微镜(SEM)结果表明, 在聚氨酯微球表面形成了聚异丙基丙烯酰胺(PNIPAAm)接枝聚合物层. 在接枝过程中, 延长反应时间与增加引发剂浓度均有利于提高接枝率. 常温下, 接枝率随反应时间延长呈线性增长, 当反应时间超过40 min后, 接枝率基本保持稳定; 而引发剂浓度对接枝率的影响存在最佳优化值, 即其浓度为单体质量分数的3%. 采用差示扫描量热法(DSC)对接枝改性前后聚氨酯微球的温敏特性进行分析表征, 证实改性后的微球在35 ℃左右出现低临界互溶温度(LCST), 在此温度附近表现出对温度敏感特性. 接触角测试与溶胀测试结果表明, 在低临界互熔温度以下, 接枝改性的聚氨酯微球具有良好的亲水性.     

Functionalization and patterning of reactive polymer brushes based on surface reversible addition and fragmentation chain transfer polymerization

We present the synthesis of reactive polymer brushes prepared by surface reversible addition–fragmentation chain transfer polymerization of pentafluorophenyl acrylate. The reactive ester moieties can be used to functionalize the polymer brush film with virtually any functionality by simple post‐polymerization modification with amines. Dithiobenzoic acid benzyl‐(4‐ethyltrimethoxylsilyl) ester was used as the surface chain transfer agent (S‐CTA) and the anchoring group onto the silicon substrates. Reactive polymer brushes with adjustable molecular weight, high grafting density, and conformal coverage through the grafting‐from approach were obtained. Subsequently, the reactive polymer brushes were converted with amino‐spiropyrans resulting in reversible light‐responsive polymer brush films. The wetting behavior could be altered by irradiation with ultraviolet (UV) or visible light. Furthermore, a patterned surface of polymer brushes was obtained using a lithography technique. UV irradiation of the S‐CTA‐modified substrates leads to a selective degradation of S‐CTA in the exposed areas and gives patterned activated polymer brushes after a subsequent RAFT polymerization step. Conversion of the patterned polymer brushes with 5‐((2‐aminoethyl)amino)naphthalene‐1‐sulfonic acid resulted in patterned fluorescent polymer brush films. The utilization of reactive polymer brushes offers an easy approach in the fabrication of highly functional brushes, even for functionalities whose introduction is limited by other strategies. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

采用层层自组装与光化学修饰法在聚氨酯表面固定生物多糖衍生物

采用层层自组装技术与光化学修饰方法相结合在聚氨酯材料表面固定生物多糖衍生物,首先合成具有光反应活性的叠氮壳聚糖,再在聚氨酯基材表面进行叠氮壳聚糖与香菇多糖硫酸酯的层层自组装,然后通过光化学反应对自组装多层膜修饰层进行交联,制备得到生物多糖衍生物层层自组装与光化学表面修饰的聚氨酯材料.通过红外光谱、X射线光电子能谱、水接触角测量仪、抗菌活性测试、溶血试验和血小板黏附测试等方法对被修饰聚氨酯材料的表面性能和生物性能进行了分析,测试结果表明修饰后的聚氨酯材料表面的亲水性和血液相容性得到改善,并且被修饰材料对大肠杆菌具有良好的抑制效果.     

Surface modification of polytetrafluoroethylene films via graft copolymerization for auto-adhesion

The surfaces of Ar plasma-pretreated polytetrafluoroethylene (PTFE) films are further functionalized via UV-induced graft copolymerization with amphoteric N,N′-dimethyl(methacryloylethyl)ammonium propansulfonate (DMAPS) either in Ar atmosphere, or under atmospheric conditions and in the absence of a polymerization initiator. The so-modified PTFE films from either process are capable of exhibiting adhesive-free adhesion or auto-adhesion with one another when brought into intimate contact in the presence of a small quantity of water. The lap shear adhesion strength increases with increasing graft concentration and can readily exceed the yield strength of the PTFE substrate. Two plasma-pretreated PTFE films also readily undergo thermal graft copolymerization with concurrent lamination when lapped together in the presence of a small quantity of the DMAPS monomer solution at elevated temperature in the atmosphere. The surface compositions of the graft-copolymerized PTFE films and the delaminated surfaces were characterized by X-ray photoelectron spectroscopy (XPS). In most cases, adhesional failure occurred near the graft-substrate interphase. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 3107–3114, 1998     

Random photografting of polymers to nanoparticles for well-dispersed nanocomposites

A simple method to achieve dispersion of nanoparticles (NPs) within polymer matrices by solution-state photografting of benzophenone (BP)-containing random copolymers is presented. A benzyl ether ligand that stabilizes NPs in solution while possessing selectivity toward hydrogen abstraction and subsequent coupling with BP was designed. This method for introducing grafts by ultraviolet (UV) light exposure affords control over the dispersion state in the resulting polymer films, as revealed by transmission electron microscopy and UV–visible spectroscopy. The evolution of the hydrodynamic sizes of particles as a function of UV dose suggests that the polymers “wrap” particles by forming multiple attachment points per chain because of the relatively rapid kinetics for the formation of subsequent attachments following the first grafting event for a given chain. In addition, the presence of unreacted BP groups allows for photolithographic patterning of well-dispersed nanocomposite films. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016, 54, 152–158     

Photochemical modification of diamond films: introduction of perfluorooctyl functional groups on their surface

Photolysis of perfluoroazooctane with diamond films led the chemical modification of the surface to introduce perfluorooctyl functional groups, confirmed by means of Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy (XPS), Raman spectroscopy, and time-of-flight secondary ion mass spectrometry measurements. Diamond films modified with fluorine moieties showed improved frictional property and reduction of surface energy, as evaluated by contact angle to water, compared with a pristine diamond film. The contact angle and friction coefficient of chemically modified diamond film are 118 degrees and 0.1, respectively. The results of the value of the contact angle depending on irradiation times are consistent with those of the F/C ratio of fluorinated diamond films by monitoring with XPS.     

Photochemical modification of polymer surface by the pendant photobase generator containing oxime‐urethane groups and its application to an image‐recording material

Copolymers containing oxime‐urethane groups were prepared by the copolymerization of methyl methacrylate and benzophenoneoximinocarbonylaminoethyl methacrylate (BCM), and their photochemical properties were examined from the UV and IR absorption spectral changes. The decomposed fraction of oxime‐urethane groups in the copolymer increased with irradiation time, but it decreased with the content of BCM units in the copolymer. Changes of the surface properties of the copolymer film on irradiation were studied by measurements of the contact angle and dyeing with an acid dye. The surface of the copolymer film changed to become more hydrophilic upon irradiation with 254 nm of UV light. After the irradiated copolymer films were treated with HCl or methanol, changes of the contact angle of water on irradiation were compared. The copolymer film was dyed by acid dyes after treatment of the irradiated film with HCl. The degree of dyeing increased with irradiation time and BCM units in the copolymer, but it was unaffected by the film thickness. Various colors were developed on the irradiated area depending on the acid dye as the developer. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1200–1207, 2002     

Enhanced photocatalytic activity of ZnO nanoparticles by surface modification with KF using thermal shock method

ZnO nanoparticles were modified with KF using thermal shock method at various temperatures in order to improve the photocatalytic activity of ZnO under both UVA and visible light irradiation. The influences of KF-modification on the crystal structure, morphology, UV–visible absorption, specific surface area as well as surface structure of ZnO were respectively characterized by XRD, FE-SEM, UV–Visible diffuse reflectance, N₂ adsorption and XPS spectroscopy. The photocatalytic activity was evaluated via the degradation of methylene blue under UVA irradiation. According to the results, the thermal shock process with KF did not modify the structure, the particle size and the optical properties of ZnO nanoparticles but successfully increase their UVA and visible light induced photocatalytic activity. This enhancement of activity may be attributed to the increase of surface hydroxyl groups and zinc vacancies of modified ZnO samples.     

Gas transport in surface‐modified low‐density polyethylene films with acrylic acid as a grafting agent

The modification of polyethylene by the grafting of poly(acrylic acid) onto the surface of one of the faces of low‐density polyethylene films with UV radiation is reported. The transport of oxygen, nitrogen, carbon monoxide, carbon dioxide, methane, ethane, ethylene, propane, and argon across surface‐modified films containing 3.7% poly(acrylic acid) has been investigated at several temperatures. The layer of poly(acrylic acid) grafted onto the surface of one of the faces of the films reduces the permeability coefficient of the gases by a factor of about 1/6. The sharp drop in the gas permeability as a result of the poly(acrylic acid) layer may arise either from the formation of ordered structures of the grafted chains or from the development of highly crosslinked structures. The values of the polymer–gas enthalpic interaction parameter for the modified film are higher than those for the unmodified one. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2828–2840, 2006     

Poly(tetrafluoroethylene) Film Surface Functionalization with 2‐Bromoisobutyryl Bromide as Initiator for Surface‐Initiated Atom‐Transfer Radical Polymerization

A PTFE film surface was modified using a combined plasma/ozone‐activated process. The modified PTFE film was further reacted with 2‐bromoisobutyryl bromide to incorporate ATRP initiators in the film surface. Surface‐initiated ATRP on PTFE films was performed using sodium styrene sulfate as a monomer. The poly(sodium styrene sulfate) chain length grafted onto PTFE film surfaces increased with increasing reaction time. Analysis using X‐ray photoelectron spectroscopy, scanning electron microscopy, atomic force microscopy and a contact angle analyzer gave evidence of the success of the PTFE surface modifications.

     

Stability and ageing of plasma treated poly(tetrafluoroethylene) surfaces

In this study CO₂, H₂/H₂O and H₂O low pressure plasma treatment of poly(tetrafluoroethylene) (PTFE) foils and of thin plasma deposited fluorocarbon polymer (PDFP) films with a structure close to PTFE was investigated. The properties of the plasma were analyzed by mass spectroscopy (MS) and optical emission spectroscopy (OES). The modified fluorocarbon surfaces were characterized by X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM), fourier transform infrared (FTIR) spectroscopy, spectroscopic ellipsometry, electrokinetic measurements and dynamic contact angle measurements in order to find optimized treatment conditions. The results of the surface modification were compared with respect to the efficiency of the plasma treatment and the stability of the modification effect at different ambient conditions. It was shown that the H₂O plasma treatment is the most effective process for the intended modification. The hydrophobic PTFE surface was converted into a more hydrophilic one. The introduced radicals after the H₂O plasma treatment can be utilized subsequently for post plasma reactions such as grafting processes.