Preparation and characterization of a polyimide nanofoam through grafting of labile poly(propylene glycol) oligomer

Preparation of a polyimide nanofoam (PI‐F) for microelectronic applications was carried out using a polyimide precursor synthesized from poly[(amic acid)‐co‐(amic ester)] and grafted with a labile poly(propylene glycol) (PPG) oligomer. Polyimide precursor was synthesized by partial esterification of poly(amic acid) (PAA) derived from pyromellitic dianhydride (PMDA) and 4,4′‐oxydianiline (ODA). The precursor was then grafted with bromide‐terminated poly(propylene glycol) in the presence of K₂CO₃ in hexamethylphosphoramide and N‐methylpyrrolidone, imidized at 200°C in nitrogen and the product was subsequently decomposed in air at 300°C to eliminate the labile PPG oligomer to produce PMDA/ODA polyimide nanofoam. Nuclear magnetic resonance spectroscopy (¹H‐NMR) and Fourier transform infrared spectroscopy (FT‐IR) techniques were used to characterize the formation of polyimide precursor and extent of grafting of PPG with polyimide. The results of thermogravimetric analysis (TGA) showed three step decomposition of nanofoam with the removal of PPG at 350°C and decomposition of polyimide at around 600°C. The polyimide nanofoams were also characterized by small angle X‐ray scattering (SAXS), field‐emission scanning electron microscopy (FE‐SEM) and transmission electron microscopy (TEM). The morphology showed nanophase‐separated structures with uniformly distributed and non‐interconnected pores of 20–40 nm in size. Dynamic mechanical analysis (DMA) indicated higher storage modulus for the foamed structure compared to the pure PI with reduction in loss tangent for the former system. Copyright © 2004 John Wiley & Sons, Ltd.     

Polyimide containing internal acetylene units linked para to the aromatic ring

4,4′-Diaminodiphenylacetylene (p-intA) was reacted with 3,3′,4,4′-biphenyltetracarboxylic dianhydride (BPDA), 3,3′,4,4′-benzophenonetetracarboxylic dianhydride (BTDA) and pyromellitic dianhydride (PMDA) in N-methyl-2-pyrrolidone (NMP) to give poly(amic acid) solution of moderate to high viscosity. Thermal imidization gave polyimide having acetylene units that are linked para to the aromatic connecting unit. Polyimide having acetylene units that are linked meta to the aromatic connecting unit also was prepared utilizing 3,3′-diaminodiphenylacetylene (m-intA) for comparison. The crosslinking behavior of the acetylene units was observed with DSC. Exotherm due to the crosslinking of the para-linked acetylene units appeared at ca. 340 to 380°C depending on the structure of polyimide, whereas meta-linked acetylene units appeared at lower temperature as 340–350°C. After thermal treatment at high temperature such as 350 or 400°C, the amount of the exotherm became smaller and finally disappeared on DSC, confirming the progress of crosslinking. Dynamic mechanical properties of the polyimide films show that glass transition temperature increased with higher heat treatment, also confirming the progress of crosslinking. Tensile properties of the polyimide films showed that rigid polyimide films consisting of p-intA with BPDA or PMDA have considerably higher modulus than those consisting of m-intA. Cold-drawing of the poly(amic acid) followed by imidization gave much higher modulus in the case of rigid polyimide. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 2395–2402, 1997     

Novel method for the preparation of poly(urethane–imide)s and their properties

A polymer blend consisting of polyimide (PI) and polyurethane (PU) was prepared by means of a novel approach. PU prepolymer was prepared by the reaction of polyester polyol and 2,4-tolylenediisocyanate (2,4-TDI) and then end-capped with phenol. Poly(amide acid) was prepared from pyromellitic dianhydride (PMDA) and oxydianiline (ODA). A series of oligo(amide acid)s were also prepared by controlling the molar ratio of PMDA and ODA. The PU prepolymer and poly(amide acid) or oligo(amide acid) solution were blended at room temperature in various weight ratios. The cast films were obtained from the blend solution and treated at various temperatures. With the increase of polyurethane component, the films changed from plastic to brittle and then to elastic. The poly(urethane–imide) elastomers showed excellent mechanical properties and moderate thermal stability. The elongation of films with elasticity was more than 300%. The elongation set after the breaking of films was small. From the dynamic mechanical analysis, all the samples showed a glass transition temperature (T_g) at ca. −15°C, corresponding to T_g of the urethane component, suggesting that phase separation occurred between the two polymer components, irrespective of polyimide content. TGA and DSC studies indicated that the thermal degradation of poly(urethane–imide) was in the temperature range 250–270°C. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 3745–3753, 1997     

Preparation of novel,high‐modulus,swollen‐ or jungle‐gym‐type polyimide gels end‐crosslinked with 1,3,5‐tris(4‐aminophenyl)benzene

A novel preparation approach for high‐performance polyimide gels that are swollen or have a jungle‐gym‐type structure is proposed. A new rigid and symmetric trifunctional amine, 1,3,5‐tris(4‐aminophenyl)benzene (TAPB), was synthesized as a crosslinker. Three different kinds of amic acid oligomers derived from pyromellitic dianhydride (PMDA), 4,4′‐oxydiphthalic anhydride (ODPA), p‐phenylenediamine (PDA), and 4,4′‐oxydianiline (ODA) were end‐crosslinked with TAPB at a high temperature to make polyimide networks with different structures. Transparent polyimide gels were obtained from the ODPA–ODA/TAPB series with high compression moduli of about 1 MPa at their equilibrium swollen states in N‐methylpyrrolidone. Microscopic phase separation occurred during the gelation–imidization process when polyimide networks were generated from PMDA–PDA/TAPB and PMDA–ODA/TAPB. After these opaque polyimide networks were dried, a jungle‐gym‐like structure was obtained for the PMDA–PDA/TAPB and PMDA–ODA/TAPB series; that is, there was a high void content inside the networks (up to 70%) and little volume shrinkage. These polyimide networks did not expand but absorbed the solvent and showed moduli as high as those of solids. Therefore, using the highly rigid crosslinker TAPB combined with the flexible monomers ODPA and ODA and the rigid monomers PMDA and PDA, we prepared swollen, high‐performance polyimide gels and jungle‐gym‐type polyimide networks, respectively. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2501–2512, 2002     

Photoconductivity of a polyimide with an alicyclic diamine: Charge carrier photogeneration in the mixed layer packing arrangement

Photoconduction mechanism of a polyimide with an alicyclic diamine, PI(PMDA/DCHM), prepared from pyromellitic dianhydride (PMDA) and 4,4′-diaminodicyclohexylmethane (DCHM) was investigated. Its UV absorption spectra, fluorescence spectra, photoconductivity, and annealing effects on the photocurrent generation were measured and compared to those of CPD, N,N′-dicyclohexylpyromellitic diimide, and PI(PMDA/DMDHM) prepared from PMDA and 3,3′-dimethyl-4,4′-diaminodicyclohexylmethane (DMDHM). Photoconductivity of PI(PMDA/DCHM) depends upon the degree of molecular packing between polymer backbones. PI(PMDA/DMDHM) has no photoconductivity, probably due to a barrier to their intermolecular packing by the existence of two methyl substituents. Photoconductivity of PI(PMDA/DCHM) would be the result of the weak intermolecular interaction formed by mixed layer packing arrangement between pyromellitic moiety of one polymer backbone and N-cyclohexyl ring of another one in the ground state. Radiation absorption of this weak intermolecular interaction immediately forms a charge–transfer complex in the excited state and produces radical cation and anion charge carriers, which lead to the photoconductivity in the bulk polyimide film of PI(PMDA/DCHM). © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 1433–1442, 1998     

Dielectric properties of oxydianiline‐based polyimide thin films according to the water uptake

For polyimide thin films, the dielectric properties were investigated with the capacitance and optical methods. The dielectric constants of the 4,4′‐oxydianiline (ODA)‐based polyimide thin films varied from 2.49 to 3.10 and were in the following decreasing order: 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (BPDA)–ODA > 1,2,4,5‐benzenetetracarboxylic dianhydride (PMDA)–ODA > 4,4′‐hexafluoroisopropylidene diphthalic dianhydride (6FDA)–ODA. According to the absorption of water, the diffusion coefficients in the films varied from 4.8 × 10^?10 to 7.2 × 10^?10 cm²/s and were in the following increasing order: BPDA–ODA < PMDA–ODA < 6FDA–ODA. The dielectric constants and diffusion coefficients of the polyimides were affected by the morphological structures, including the molecular packing order. However, because of the water uptake, the changes in the dielectric constants in the polyimide thin films varied from 0.49 to 1.01 and were in the following increasing order: BPDA–ODA < 6FDA–ODA < PMDA–ODA. Surprisingly, 6FDA–ODA with bulky hexafluoroisopropylidene groups showed less of a change in its dielectric constant than PMDA–ODA. The total water uptake for the polyimide thin films varied from 1.43 to 3.19 wt % and was in the following increasing order: BPDA–ODA < 6FDA–ODA < PMDA–ODA. This means that the changes in the dielectric constants in the polyimide thin films were significantly related to the morphological structure and hydrophobicity of hexafluoroisopropylidene groups. Therefore, the morphological structure and chemical affinity in the polyimide thin films were important factors in controlling the dielectric properties. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2190–2198, 2002     

Crystalline structure and morphology of microphases in compatible mixtures of poly(tetrahydrofuran‐methyl methacrylate) diblock copolymer and polytetrahydrofuran

The crystalline structure and morphology of compatible mixtures of poly(tetrahydrofuran‐methyl methacrylate) diblock copolymers (PTHF‐b‐PMMA) with a polytetrahydrofuran homopolymer (PTHF) were studied with synchrotron X‐rays. Wide‐angle diffraction was used to study the crystalline structures in a confined lamellar region with a PTHF thickness ranging from 12.2 to 19.5 nm, and in a PTHF matrix with an interface distance between the PMMA cylinders ranging from 17 to 22 nm. As the above thickness values are around the long period (ca. 17 nm) of PTHF homopolymer under the crystallization condition used, the crystalline structure has been found to be very sensitive to the average thickness of the PTHF phase. The changes in the diffraction patterns with changing PTHF homopolymer content suggested a chain folding model in confined PTHF lamellae with the PTHF fiber axes being perpendicular to the thick PTHF lamella. In the case of hexagonally packed cylindrical PMMA microdomains with an interface distance ranging from 12 to 16 nm, the effects of PMMA cylinders on the crystallization morphology of PTHF in the PTHF matrix, and the effects of the PTHF crystallization on the hexagonally packed structure of PMMA cylinders were also studied. It is shown that only when the interdistance of two neighboring PMMA cylinders is comparable with the long period of the pure PTHF homopolymer, ordered PTHF stacks can be formed in the PTHF matrix. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 779–792, 1999     

Water sorption and activation energy in polyimide thin films

The water sorption behavior and the activation energy were investigated for various chemical structure polyimide thin films; BPDA‐PDA, BPDA‐ODA, PMDA‐ODA, and 6FDA‐ODA. The activation energy for the water diffusion varied in the range of 5.53 to 9.27kcal/mol, and was in the increasing order: BPDA‐PDA < BPDA‐ODA < PMDA‐ODA < 6FDA‐ODA. BPDA‐PDA and BPDA‐ODA polyimide films showed relatively well‐ordered morphological structure, which results in relatively low diffusion coefficient and high activation energy. It was found that the diffusion coefficient and the activation energy are significantly related to the in‐plane orientation, crystallinity, and packing order in the polyimide thin films. The morphological structure was predominant factors for the water diffusion coefficient and activation energy in the polyimide thin films. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2714–2720, 2000     

Dynamic mechanical and solid-state NMR determination of molecular-scale heterogeneity in a raw elastomer,a microcrystalline polymer,and their blend

Dynamic mechanical and solid-state ¹³C nuclear magnetic resonance (NMR) analyses have been used to assess a molecular-scale heterogeneity in a raw elastomer (butadiene-acrylonitrile copolymer elastomer, NBR), a microcrystalline polymer (poly(vinyl chloride), PVC), and their 50/50 blend. The presence of the microcrystalline heterogeneity in PVC and in the blend was characterized by the temperature dependence of the frequency-swept dynamic mechanical behavior. The NMR T_1ρ relaxation experiments with cross-polarization (CP) and magic-angle spinning (MAS) revealed that (1) NBR contained a substantial fraction (ca. 27%) of a molecular-scale heterogeneity identified as butadiene blocks, (2) the fraction of microcrystallites in PVC was ca. 14%, (3) pure phases of both component polymers were present in the blend, dispersed in the mixed matrix, (4) the upper limit of the heterogeneous domains was estimated to be ca. 2.4 nm, and (5) fractions of heterogeneity tend to increase upon blending, indicating that the solubility of the butadiene block and syndiotactic PVC block decreases in the blend. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys, 35: 709–716, 1997     

Small‐angle X‐ray scattering investigation of carbon nanotube‐reinforced polyacrylonitrile fibers during deformation

Structural changes during deformation in solution‐ and gel‐spun polyacrylonitrile (PAN) fibers with multi‐ and single‐wall carbon nanotubes (CNTs), and vapor‐grown carbon nanofibers were investigated using synchrotron X‐ray scattering. Previously published wide‐angle X‐ray scattering (WAXS) results showed that CNTs deform under load, alter the response of the PAN matrix to stress, and thus enhance the performance of the composite. In this article, we find that the elongated scattering entities that give rise to the small‐angle X‐ray scattering (SAXS) in solution‐spun fibers are the diffuse matrix‐void interfaces that follow the Porod's law, and in gel‐spun fibers these are similar to fractals. The observed smaller fraction of voids in the gel‐spun fibers accounts for the significant increase in the strength of this fiber. The degree of orientation of the surfaces of the voids is in complete agreement with those of the crystalline domains observed in WAXS, and increases reversibly upon stretching in the same way as those of the crystalline domains indicating that the voids are integral parts of the polymer matrix and are surrounded by the crystalline domains in the fibrils. The solution‐spun composite fibers have a larger fraction of the smaller (<10 nm) voids than the corresponding control PAN fibers. Furthermore, the size distribution of the voids during elongation changes greatly in the solution spun PAN fiber, but not so in its composites. The scattered intensity, and therefore the volume fraction of the voids, decreases considerably above the glass transition temperature (T_g) of polymer. Implications of these observations on the interactions between the nanotubes and the polymer are discussed. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 2394–2409, 2009     

Multiblock copolymers of ε–caprolactone and ethylene glycol containing periodic side‐chain carboxyl groups: Synthesis,characterization, and nanoparticle preparation

Multiblock copolymers containing periodically spaced side‐chain carboxyl groups were obtained by a two‐step synthesis involving the preparation of ABA triblock prepolymers of ε‐caprolactone (A blocks) and ethylene glycol (B block) followed by chain extension to ABA_n multiblock copolymers by reaction with pyromellitic dianhydride (PMDA). NMR analysis demonstrated the incorporation of PMDA in polymer chain and revealed the possibility of PMDA units to exist in two isomers, cisoid and transoid forms. Chain extension resulted in the incorporation of free carboxylic groups in polymer backbone and in an almost twofold increase of molecular weight. Thermal analysis indicated that the presence of PMDA residues interferes with the formation of crystalline phases by the chain‐extended polymers. The polymers were found to slowly degrade in buffer solution at 37 °C. Further, the carboxylated polymers can be processed into nanoparticulates by nanoprecipitation. Depending on the selected organic solvent, the particulate was constituted by either a monodispersed nanoparticles with average size of 150 nm or a bimodal distribution centered at about 100 nm and 7 μm. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 3800–3809     

Synthesis of a hexafluoropropylidene-bis(phthalic anhydride)-based polyimide and its conducting polymer composites with polypyrrole

A new electrically conducting composite film from polypyrrole and 4,4′-(hexafluoroisopropylidene)-bis(phthalic anhydride)-based polyimide was prepared. Pyrrole and the dopant ion can easily penetrate through the polyimide substrate and electropolymerize on the platinum (Pt) electrode due to the swelling of the polyimide on the metal electrode. The electrochemical properties of polypyrrole-polyimide (PPy/PI) composite films have been investigated by using cyclic voltammetry. The PPy/PI composite film is suitable for use as the electroactive material owing to its stable and controllable electrochemical properties. The electrical conductivity of composites falls in the range 0.0035–15 S/cm. Scanning electron micrograph, FTIR, and thermal studies indicate that PPy and PI form a homogeneous material rather than a simple mixture. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 3009–3016, 1997     

Stress behaviors and thermal properties of polyimide thin films depending on the different curing process

The effect of high boiling point solvent on the residual stress behaviors of semiflexible structure poly(4,4′‐oxydiphenylene pyromellitimide) (PMDA‐ODA) and pseudo‐rodlike poly(p‐phenylene biphenyltetracarboximide) (BPDA‐PDA) polyimide was investigated. As a solvent, a mixed solution of 20 wt % cyclohexyl‐2‐pyrrolidone (CHP; bp = 307 °C) and 80 wt % n‐methyl‐2‐pyrrolidone (NMP; bp = 202 °C) was used. The effects of solvent system and imidizing history on the morphological structure, as well as residual stress, were significantly high in the BPDA‐PDA having high chain rigidity, but relatively low in the semiflexible PMDA‐ODA with low chain rigidity. In addition, rapidly cured films prepared from PAA (NMP/CHP) showed higher residual stress and a lower degree of molecular anisotropy than slowly cured film imidized from PAA (NMP). This was induced by high chain mobility in polyimide thin films prepared from PAA (NMP/CHP) during the thermal cure process. Therefore, molecular anisotropy, depending on the solvent system and imidizing history, might be one of the important factors leading to low residual stress in polyimide thin films. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2879–2890, 2000     

Unique fluorescence behavior of perylenetetracarboxydiimides in polyimide systems

Perylenetetracarboxydiimide (PEDI) molecularly dispersed in polyamic acid (PAA) and polyimide (PI) films has unique fluorescence properties. An originally strong fluorescence of PEDI is efficiently quenched in the PAA films. The systematic variation of the chain structure of the PAA matrices revealed that the aromatic amide groups in the PAA chains function as a quencher. When a PAA derived from 3,4,3′4′-biphenyltetracarboxylic dianhydride (BPDA) and p-phenylenediamine (PDA), BPDA/PDA, was used as a matrix polymer, the fluorescence of the dye dispersed in the film increased abruptly as imidization of the matrix proceeds. But annealing at temperatures higher than 320°C in the step-heating process caused a gradual decrease in the fluorescence intensity. The decreased intensity results from the dye–PDA units interactions intensified by the denser molecular packing of the matrix polymer chains. PEDI shows significant dependence of the fluorescence intensity on the chain structure of the PI matrices. In the various PI films containing a fixed diamine component, the dye fluorescence intensity reduces linearly with an increase in the intramolecular charge transfer ability of the PI matrices. From the result, we propose a fluorescence quenching mechanism through multistep electron transfer processes. The BPDA/PDA polyimide matrix leads to a strong PEDI fluorescence whereas the pyromellitic dianhydride (PMDA)-based PI matrices do not. For the blends composed of these PIs, the fluorescence of PEDI bound into the main chains provides a valuable indicator of the miscibility on the molecular level. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 827–840, 1998     

Synthesis and properties of fluorinated polyimides. 1. Derived from novel 4,4″‐bis(aminophenoxy)‐3,3″‐trifluoromethyl terphenyl

A new diamine monomer, 4,4″‐bis(aminophenoxy)‐3,3″‐trifluoromethyl terphenyl (ATFT) was synthesized that led to a number of novel fluorinated polyimides by solution as well as thermal imidization routes when reacted with different commercially available dianhydrides like pyromellatic dianhydride (PMDA), benzophenone tetracarboxylic acid dianhydride (BTDA), or 2,2‐bis(3,4‐dicarboxyphenyl) hexafluoropropane (6FDA). The polyimides ATFT/BTDA and ATFT/6FDA derived from both routes were soluble in several organic solvents such as N,N‐dimethylformamide, N,N‐dimethylacetamide, and dimethyl sulfoxide. The polyimide ATFT/PMDA was only soluble in N‐methylpyrollidone. The polyimide films had low water absorption of 0.3–0.7%, low dielectric constants of 2.72–3.3 at 1 Hz, refractive indices of 1.594–1.647 at 589.3 nm, and optical transparency >85%. These polyimides showed very high thermal stability with decomposition temperatures (5% weight loss) up to 532 °C in air and good isothermal stability; only 7% weight loss occurred at 400 °C after 7 h, and less than 0.6% weight loss was observed at 315 °C for 5 h. Transparent thin films of these polyimides exhibited tensile strengths up to 112 MPa, a modulus of elasticity up to 3.05 GPa, and elongation at break up to 21% depending on the repeating unit structure. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1016–1027, 2002     

Preparation and adhesion of ultrathin polyimide films on polycrystalline silver

4.4-oxydianiline (ODA) and 1,2,3,5-benzenetetracarboxylic anhydride (PMDA) were deposited from the vapor phase onto a polycrystalline silver substrate and polymerization of the two components to form ultrathin polyimide films (d≈ 11 Å) was followed by X-ray photoelectron spectroscopy. Both PMDA and ODA chemisorb on the clean surface under partial fragmentation. Co-deposition of ODA and PMDA followed by heating of the substrate led to formation of thermally stable (T<450°C) polyimide films. Our data indicate that adhesion of the polyimide film to the surface involves chemical bonding to fragmented PMDA and/or ODA chemisorbed on the substrate. Our experiments show that polyimide films can be prepared sufficiently thin to allow the application of surface sensitive techniques to probe the substrate-polymer interface and to study the basic physics and chemistry of adhesion.     

Carbon nanocones/discs – a new type of filler to improve the thermal and mechanical properties of polymer films

The mechanical characteristics and thermal properties of composite films based on the thermally stable aromatic polyimide (PI) (PMDA‐ODA) and carbon nanocones/discs (CNC) were studied. The introduction of CNC to PMDA‐ODA leads to the substantial increase of film stiffness. The Young's modulus values of the composite films are somewhat higher than those of the previously characterized composite films of this PI filled with nanoclay, carbon nanofibers, and asbestos‐like hydrosilicate nanotubes. The introduction of CNC into PMDA‐ODA (concentrations of CNC were up to 15 vol%) does not cause any marked aggregation of nanoparticles. The presence of CNC in the PI matrix does not affect the glass transition temperature of the polymer but hinders chain mobility at temperatures above T_g. This behavior makes it possible to increase the working temperature range of the composite films containing more than 5 vol% of CNCs, up to the temperature of thermal decomposition. The introduction of CNC into PMDA‐ODA leads to dramatic (～12 orders of magnitude) increase of active electrical conductivity of the material. Copyright © 2011 John Wiley & Sons, Ltd.     

Preparation and morphological,electrical, and mechanical properties of polyimide‐grafted MWCNT/polyimide composite

Precursor of polyimide, polyamic acid has been prepared sucessfully. Acid‐modified carbon nanotube (MWCNT) was grafted with soluble polyimide then was added to the polyamic acid and heated to 300 °C to form polyimide/carbon nanotube composite via imidation. Morphology, mechanical properties and electrical resistivity of the MWCNT/polyimide composites have been studied. Transmission electron microscope microphotographs show that the diameter of soluble polyimide‐grafted MWCNT was increased from 30–60 nm to 200 nm, that is a thickness of 70–85 nm of the soluble polyimide was grafted on the MWCNT surface. PI‐g‐MWCNT was well dispersed in the polymer matrix. Percolation threshold of MWCNT/polyimide composites has been investigated. PI‐g‐MWCNT/PI composites exhibit lower electrical resistivity than that of the acid‐modified MWCNT/PI composites. The surface resistivity of 5.0 phr MWCNT/polyimide composites was 2.82 × 10⁸ Ω/cm² (PI‐g‐MWCNT) and 2.53 × 10⁹ Ω/cm² (acid‐modified MWCNT). The volume resistivity of 5.0 phr MWCNT/polyimide composites was 8.77 × 10⁶ Ω cm (PI‐g‐MWCNT) and 1.33 × 10¹³ Ω cm (acid‐modified MWCNT).Tensile strength and Young's modulus increased significantly with the increase of MWCNT content. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3349–3358, 2007     

Electron microscopy investigations of the morphology of a polyester-polyurethane

In the current paper the morphology of a slightly crosslinked polyester-polyurethane (hard-segment content ca. 33 wt.-%) is studied by means of transmission electron microscopy (TEM). A new staining technique based on ruthenium tetroxide was applied. This new technique allows the unambiguous visualization of the typical microdomain structure of the polyurethane and also of a wide size spectrum of globular hard-segment-rich domains which result from phase separation in the early stage of preparation. The hard-segment-rich microdomains have a size between 1.5 and 10 nm while the globular domains span a size spectrum from 10 to 2000 nm.     

Imidization and interdiffusion of poly(amic ethyl ester) precursors of PMDA/3,4′-ODA

Para-, meta-, and mixed isomeric poly(amic ethyl ester) precursors of the polyimide based on pyromellitic dianhydride (PMDA) and 3,4′-oxydianiline (3,4′-ODA) were synthesized. The intrinsic viscosity of each of the isomers was measured in an NMP solution and found to be less than corresponding isomers derived from PMDA and 4,4′-oxydianiline (4,4′-ODA) precursors with comparable molecular weight. The imidization and solvent retention were measured as a function of imidization temperatures, T_i using forward recoil spectrometry (FRES). For samples cast from a single solvent, either N-methyl pyrrolidone (NMP) or dimethyl sulfoxide (DMSO), no difference was observed in the temperature-dependent imidization behavior between the isomers. In all cases the imide fraction f increased as T_i increased, and reached a value of unity, i.e., full conversion at 400°C. At the same T_i, samples cast from DMSO showed a slightly higher f than samples cast from NMP. FRES and time of flight FRES (TOF-FRES) were used to measure the interdiffusion distance, w, of deuterium-labeled tracers into nondeuterated base layers of the polyimide of PMDA/3,4′-ODA treated at various T_i. The primary determinant of w for all isomers was T_i, and the particular isomer used as either the base or the tracer molecule did not seem to affect w. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 2247–2258, 1998