Acrylonitrile–maleic anhydride copolymer membrane (II): effects of post‐treatment1

The effects of post‐treatment (including thermal treatment and base treatment) on the structure and performance of acrylonitrile–maleic anhydride (AN‐MA) copolymer membrane were investigated. The water flux decreased gradually (except the deviations when the temperature of thermal treatment was 50 °C or the time of thermal treatment was 50 min but rejection of bovine serum albumin increased slowly with increasing temperature or prolonging the time of thermal treatment. “The swelling effect of water in network” was proposed to explain the deviations. AN‐MA copolymer membrane is not resistant to a base. However, the performance of the membrane can be adjusted by treatment with a dilute base solution. Copyright © 2000 John Wiley & Sons, Ltd.     

Monoesterification of styrene–maleic anhydride copolymers with alcohols in ethyl benzene: Catalysis and kinetics

A kinetic investigation on the monoesterification reaction of the maleic anhydride residue (MA) in styrene-maleic anhydride copolymers with aliphatic alcohols was carried out in ethyl benzene solution. By comparison to classic catalysts such as tributylamine (TBA) and pyridine, 4-dimethylaminopyridine (4DMAP) is by far the most effective catalyst for this reaction. While both general base and nucleophilic mechanisms contribute to the reaction catalyzed by TBA or pyridine, a nucleophilic mechanism prevails with 4DMAP. This reaction is reversible, and its chemical equilibrium constant decreases significantly with increasing temperature. Both kinetic and thermodynamic results showed that in the presence of 4DMAP, the forward and reverse reactions are second and first order, respectively. The existence of side reactions, reactivity of two styrene-maleic anhydride copolymers of different MA contents as well as two aliphatic alcohols of different lengths are also addressed. © 1993 John Wiley & Sons, Inc.     

Acrylonitrile–maleic anhydride copolymer membrane (I): effects of casting conditions

The effects of casting conditions, including casting solution (composition and temperature) and coagulation conditions (pre‐evaporation time, temperature and concentration of coagulation bath) on the structure and performance of acrylonitrile–maleic anhydride copolymer membrane have been investigated. The results showed that the water flux decreased gradually while the rejection of bovine serum albumin (BSA) decreased as the concentration of copolymer increased. When the total solid concentration was kept unchanged, the water flux increased with additive polyvinylpyrrolidone (PVP), the rejection did not decrease until the ratio of PVP/copolymer was 60%. When the content of copolymer in the casting solution was kept constant, the water flux decreased rapidly while the rejection increased a little (compared with the case of no additive) as the ratio of PVP/copolymer increased. As to the temperature of casting solution, the water flux had a maximum at 45 °C and the rejection had a maximum and a minimum at 45 and 55 °C, respectively. The water flux had a maximum value when the pre‐evaporation time was 40 sec. The rejection of BSA was almost unchanged when the pre‐evaporation time was less than 40 sec. and then decreased and reached a minimum value at 60 sec. As the temperature of coagulation bath increased, the water flux reached a maximum at 35 °C while the rejection increased uniformly. With increasing the concentration of DMSO in the coagulation bath, the water flux decreased gradually and got to a minimum at 50 wt% as the concentration of dimethylsulfoxide in the coagulation bath increased, but no apparent effect on the rejection was observed. Copyright © 2000 John Wiley & Sons, Ltd.     

热重法测定高马来酸酐含量苯乙烯-马来酸酐共聚物的组成

高马来酸酐含量苯乙烯-马来酸酐共聚物(SMA)是一种具有优良耐热性、刚性和尺寸稳定性的新型高分子材料.由于SMA分子中含有极性很强、反应活性很高的酸酐官能团,所以它被广泛应用于涂料、粘合剂的改性剂、地板抛光的乳化剂、复合材料和颜料的分散剂、水处理剂等领域[1-5].     

Synthesis and micellization of amphiphilic poly(sebacic anhydride)–poly(ethylene glycol)–poly(sebacic anhydride) block copolymers

Amphiphilic biodegradable block copolymers [poly(sebacic anhydride)–poly(ethylene glycol)–poly(sebacic anhydride)] were synthesized by the melt polycondensation of poly(ethylene glycol) and sebacic anhydride prepolymers. The chemical structure, crystalline nature, and phase behavior of the resulting copolymers were characterized with ¹H NMR, Fourier transform infrared, gel permeation chromatography, and differential scanning calorimetry. Microphase separation of the copolymers occurred, and the crystallinity of the poly(sebacic anhydride) (PSA) blocks diminished when the sebacic anhydride unit content in the copolymer was only 21.6%. ¹H NMR spectra carried out in CDCl₃ and D₂O were used to demonstrate the existence of hydrophobic PSA domains as the core of the micelle. In aqueous media, the copolymers formed micelles after precipitation from water‐miscible solvents. The effects on the micelle sizes due to the micelle preparation conditions, such as the organic phase, dropping rate of the polymer organic solution into the aqueous phase, and copolymer concentrations in the organic phase, were studied. There was an increase in the micelle size as the molecular weight of the PSA block was increased. The diameters of the copolymer micelles were also found to increase as the concentration of the copolymer dissolved in the organic phase was increased, and the dependence of the micelle diameters on the concentration of the copolymer varied with the copolymer composition. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1271–1278, 2006     

Surface modification of fine colloidal silica with copolymer silane-coupling agents composed of maleic anhydride

The reactivity of copolymer silane composed of maleic anhydride in the modification of fine colloidal silica was studied. The reaction of colloidal silica of 10 and 45-nm diameter with trimethoxysilyl-terminated poly(maleic anhydride-co-styrene) [P(MA-ST)] and poly(MA-co-methyl methacrylate) in tetrahydrofuran resulted in effective surface modification without particle aggregation. From the results that the reaction using the polystyrene silane of low molecular weight led to partial aggregation, it was suggested that the steric interaction between relatively rigid copolymer chains having a maleic anhydride moiety adsorbed on the silica prevented the aggregation in the reaction. The ²⁹Si cross-polarization magic-angle-spinning NMR spectra of P(MA-ST)-modified silica showed that the polymer silane was bound to the silica surface by the direct reaction with silica hydroxyl groups and via the polymerization. Received: 27 June 2001 Accepted: 6 September 2001     

Monitoring polyolefin modification along the axis of a twin‐screw extruder. II. Maleic anhydride grafting

The physico‐chemical phenomena developing along the screw axis of a twin‐screw extruder during the grafting of maleic anhydride (MA) onto polyolefins [polyethylene (PE), ethylene–propylene rubber (EPM), and polypropylene (PP)] were investigated. For this purpose, sampling devices located along the extruder barrel were used to collect polymer samples that were subsequently characterized to follow the degrees of grafting and crosslinking or degradation. A similar evolution of MA grafting was observed regardless of the polyolefin type or MA and peroxide concentration when grafting was performed under identical conditions, that is, the same peroxide type and set temperature. A correlation between the MA grafting and the calculated peroxide decomposition was established. Chemical reactions occurred along the extruder axis until the peroxide was fully converted. More detailed quantitative measurements of the peroxide decomposition and MA grafting would allow the development of accurate process models. The final MA content depended on the polyolefin composition (PE > EPM ≫ PP). As expected for PE, crosslinking occurred in addition to grafting, but after a certain residence time, the PE network degraded. The PP viscosity reduction after MA grafting was due to the conversion of tertiary PP radicals into primary PP radicals after grafting. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3919–3932, 2000     

Controlled radical copolymerization of styrene and maleic anhydride and the synthesis of novel polyolefin‐based block copolymers by reversible addition–fragmentation chain‐transfer (RAFT) polymerization

Reversible addition–fragmentation chain transfer (RAFT) was applied to the copolymerization of styrene and maleic anhydride. The product had a low polydispersity and a predetermined molar mass. Novel, well‐defined polyolefin‐based block copolymers were prepared with a macromolecular RAFT agent prepared from a commercially available polyolefin (Kraton L‐1203). The second block consisted of either polystyrene or poly(styrene‐co‐maleic anhydride). Furthermore, the colored, labile dithioester moiety in the product of the RAFT polymerizations could be removed from the polymer chain by UV irradiation. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3596–3603, 2000     

RAFT radical copolymerization of beta‐pinene with maleic anhydride and aggregation behaviors of their copolymer in aqueous solution

RAFT copolymerization of beta‐pinene and maleic anhydride was successfully achieved for the first time, using 1‐phenylethyl dithiobenzoate as chain transfer agent in a mixed solvent of tetrehydrofuran and 1.4‐dioxane (1:9, v/v) at a feed molar ratio of beta‐pinene to maleic anhydride as 3:7, and the alternating copolymer was prepared with predetermined molecular weight and narrow molecular weight distribution. Furthermore, using former alternating copolymer as a macro‐RAFT agent, block copolymer poly(beta‐pinene‐alt‐maleic anhydride)‐b‐polystyrene was synthesized in a chain extending with styrene. Hydrolysis of this block copolymer under acidic conditions formed a new amphiphilic block copolymers poly(beta‐pinene‐alt‐maleic acid)‐b‐polystyrene whose self‐assembly behaviors in aqueous solution at different pH were investigated through SEM and DLS. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1422–1429     

Radiation-induced graft polymerization of maleic acid and maleic anhydride onto ultra-fine powdered styrene–butadiene rubber (UFSBR)

The functionalization of ultra-fine powdered styrene–butadiene rubber (UFSBR) was carried out using gamma radiation-induced graft polymerization of maleic acid (MA) and maleic anhydride (MAH), respectively. It was found that the graft yield of MA onto UFSBR increased rapidly up to the peak and then decreased with increasing MA content. Moreover, the peak shifted to the direction of lower MA content with increasing absorbed dose. Similarly, there was the peak of graft yield with increasing MAH content for grafting of MAH onto UFSBR, whereas the peak of graft yield was achieved at 10 wt% MAH content at different absorbed doses. On the other hand, increasing absorbed dose and decreasing monomer contents are useful to improve the graft efficiency of MA and MAH. At high dose and low monomer content, the graft yield of MAH onto UFSBR is higher than that of MA. FTIR spectra confirmed that both MA and MAH can be grafted successfully onto the UFSBR under gamma irradiation, respectively. Comparing with maleation of rubber by melt grafting, the graft yield of MAH on UFSBR is higher, which can be attributed to the network structure and nanometer size of UFSBR as well as high energy provided by radiation.     

A study on melt grafting of maleic anhydride onto low‐density polyethylene and its blend with polyamide 6

Graft copolymerization of low‐density polyethylene (LDPE) with a maleic anhydride (MAH) was performed using intermeshing corotating twin‐screw extruder in the presence of benzoyl peroxide (BPO). The LDPE/polyamide 6 (PA6) and LDPE‐g‐MAH/PA6 blends were prepared in a corotating twin‐screw extruder. The melt viscosity of the grafted LDPE was measured by a capillary rheometer. The grafted copolymer was characterized by Fourier transform infrared spectroscopy (FTIR) and scanning electron microcopy (SEM). The influence of the variation in temperature, BPO and MAH concentration, and temperature on the grafting degree and on the melt viscosity was studied. The grafting degree increased appreciably up to about 0.45 phr and then decreased continuously with an increasing BPO concentration. According to the FTIR analysis, it was found that the amount of grafted MAH on the LDPE chains was ～5.1%. Thermal analysis showed that melting temperature of the graft copolymers decreases with increasing grafting degree. In addition to this, loss modulus (E″) of the copolymers first increased little with increasing grafting and then obviously decreased with increasing grafting degree. Furthermore, the results revealed that the tensile strength of the blends increased linearly with increasing PA6 content. The results of SEM and mechanical test showed that the blends have good interfacial adhesion and good stability of the phase structure, which is reflected in the mechanical properties. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 267–275, 2010     

1H NMR assignment of oligomeric grafts of maleic anhydride‐grafted polyolefin

The ¹ H NMR assignment of oligomeric grafts of maleic anhydride (MA)‐grafted polyolefin (PO), MA‐g‐PO hereafter, was experimentally demonstrated for the first time using NMR spectroscopy. ¹³ C DEPT, ¹ H‐¹ H DQF‐COSY, and ¹ H T₂‐edited spectroscopy of MA‐g‐PO proved that peaks of the intermediate methine protons of succinic anhydride oligomeric grafts, which are nearly tetrameric, are observed at 2.5–3.5 ppm and show broadening. Copyright © 2012 John Wiley & Sons, Ltd.     

Melt modification of poly(styrene‐co‐maleic anhydride) with alcohols in the presence of 1,3‐oxazolines

Various copolyesteramides were prepared by melt compounding at 220 °C involving reaction of poly(styrene‐co‐maleic anhydride), SMA, with 6, 17, and 28 wt % maleic anhydride content, and 1‐dodecanol, C12OH, in the presence of 2‐undecyl‐1,3‐oxazoline, C11OXA. Copolymer architectures were examined by means of ¹H NMR, FTIR, DSC, and TGA using model compounds prepared via solution reactions. While conversion of anhydride with alcohol was poor due to the thermodynamically favored anhydride ring formation, very high conversions were achieved when stoichiometric amounts of C11OXA were added. According to spectroscopic studies esteramide groups resulted from reaction of oxazoline with carboxylic acid intermediate. In the absence of alcohol, C11OXA reacted with anhydride to produce esterimides. Effective attachment of flexible n‐alkyl side chains via simultaneous reaction of C12OH and C11OXA resulted in lower glass‐transition temperatures of copolyesteramides. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1222–1231, 2000     

Synthesis,characterization and cytotoxicity of polyethylene glycol coupled zinc oxide–chemically converted graphene nanocomposite on human OAW42 ovarian cancer cells

Present work reports for the first time on successful synthesis of polyethylene glycol (PEG) coupled ZnO–chemically converted graphene (CCG) nanocomposites (ZGP) as well as pristine nano ZnO (ZO), ZnO–CCG (ZG) and ZnO–PEG (ZP) by adopting facile solvothermal method using zinc acetate dihydrate, graphene oxide and PEG as precursor materials. X‐ray diffraction measurement of samples showed nanocrystalline hexagonal ZnO. Agglomeration of ZnO nanoparticles formed microspheres in ZG, and the agglomeration was found to be decreased in ZGP as revealed from field emission scanning and transmission electron microscopes. Raman and FTIR spectral studies evidenced the presence of chemically interacted CCG and polyethylene glycol in the nanocomposites. Content of the organics in ZGP was determined by thermogravimetric analysis. A mechanism was proposed on the formation of ZGP nanocomposite. From the measurement of in vitro cytotoxicity, quantitative cell viability (CV) of human ovarian cancer cell line, OAW42, was obtained from control to a maximum of 200 µg/ml of sample concentrations. An excellent CV of the cancer cells was observed (nearly ~80% of viable cells at 50 µg/ml dose with respect to the control) for ZGP compared to ZO, ZG and ZP samples. The effective role of CCG and PEG in ZGP nanocomposite for enhancing the cell viability was explained. This simple strategy could be beneficial for synthesis of other metal oxide towards biomedical applications. Copyright © 2015 John Wiley & Sons, Ltd.     

Effect of mixing conditions on the morphology and properties of polystyrene/polyethylene blends compatibilized with styrene–butadiene block copolymers

The effect of mixing conditions on the morphology, molten‐state viscoelastic properties, and tensile impact strength of polystyrene/polyethylene (80/20) blends compatibilized with styrene–butadiene block copolymers containing various numbers and lengths of blocks was studied. Under all mixing conditions, an admixture of a styrene–butadiene block copolymer led to a finer phase structure and to an increase in the dynamic viscosity, storage modulus, and tensile impact strength. The effects were stronger for S–B diblock with a short styrene block than for S–B–S–B–S pentablock with long styrene blocks (where S represents styrene and B represents butadiene). For all blends mixed longer than 2 min, the mixing time had only a small effect on their morphology and properties. Surprisingly, the localization of S–B diblock copolymers was strongly dependent on the rate of mixing. The mixing rate had a nonnegligible effect on the viscoelastic properties of the compatibilized blends. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 609–622, 2003     

Amphiphilic graft copolymers based on ultrahigh molecular weight poly(styrene-alt-maleic anhydride) with poly(ethylene glycol) side chains for surface modification of polyethersulfone membranes

Amphiphilic graft copolymers having ultrahigh molecular weight poly(styrene-alt-maleic anhydride) (SMA) backbones and methoxyl poly(ethylene glycol) (MPEG) grafts were synthesized via the esterification between anhydride groups with hydroxyl groups. The synthesized graft copolymers, SMA-g-MPEGs, were used as additives in the preparation of polyethersulfone (PES) membranes via phase inversion process. X-ray photoelectron spectroscopy (XPS) analysis showed the comb-like graft copolymers spontaneously segregated to membrane surface during membrane formation. Water contact angle measurements and water absorbance experiments indicated the PES/SMA-g-MPEG blend membranes were much more hydrophilic than pure PES membrane. The blend membranes had stronger protein adsorption resistance than pure PES membrane did. After washed using de-ionized water for 25 days, the blend membranes exhibited higher hydrophilicity and stronger protein adsorption resistance. This phenomenon was attributed to the further accumulation of SMA-g-MPEG additives on membrane surface in aqueous conditions. SMA-g-MPEGs can be well preserved in membrane near-surface and not lost during membrane washing due to their high molecular weight and comb-like architecture.     

Surface charge modulation of poly(ethylene glycol)–poly( , -lactide) block copolymer micelles: conjugation of charged peptides

Block copolymer micelles with aldehyde functionality were prepared in aqueous medium by dialyzing the N,N-dimethylacetamide solution of α-acetoxy-poly(ethylene glycol)-poly( , -lactide) block copolymer (acetal-PEG–PDLLA) against water, followed by mild acid treatment to convert the acetal moiety of the micelle to the aldehyde group. Peptidyl ligands (phenylalanine (Phe) and tyrosyl–glutamic acid (Tyr–Glu)) were then chemically conjugated to the micelle through Schiff base formation and successive reductive amination using NaBH₃CN. Micelles with peptidyl ligands thus prepared have a size of approximately 40 nm with extremely narrow distribution (μ₂/ ²<0.1) based on cumulant analysis of dynamic light scattering. A maximum 53% of the PEG-chain end of the micelle could be converted into peptidyl groups. Zeta potential values of Tyr–Glu derivatized micelles were well correlated with the amount of conjugated ligands, controllable over the range of 0 to−9 mV in sodium phosphate buffer (pH 7.4, 10 mM). These micelles with peptidyl ligands may have a utility for exploring the effect of the surface charge on the pharmacokinetic behavior of particulate systems as well as for modulated drug delivery where cellular peptidyl receptors play a substantial role.     

Kinetics and mechanistic investigation of epoxy–anhydride compositions cured with quaternary phosphonium salts as accelerators

Mechanism and curing kinetics of bisphenol A epoxy resin–iso‐methyltetrahydrophthalic anhydride compositions using quaternary phosphonium salts as accelerators were investigated by differential scanning calorimetry (DSC) and electrospray mass‐spectrometry (ESI‐MS). The DSC method was applied to investigate curing kinetics and apparent activation energy values for the overall curing process. The DSC results showed that some of the phosphonium salts lead to a lower activation energy, that means they are more effective accelerators for the curing of epoxy–anhydride systems. The mechanism of curing was studied by ESI‐MS using the model reaction of epichlorohydrin (E) with phthalic anhydride (PA) in the presence of phosphonium salts or 2‐methylimidazole. Products containing the alkyl moiety of the phosphonium salt in form of alkyl esters could be identified. This suggests that the phosphonium salts activate the anhydride by electrophilic attack. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 1088–1097     

Hydrolytic degradation of polyester–polyether block copolymer based on polycaprolactone/poly(ethylene glycol)/polylactide

Polyester–polyether block copolymers based on polycaprolactone/poly(ethylene glycol)/polylactide (PCEL) with various compositions were synthesized by direct copolymerization of ϵ‐caprolactone, L ‐lactide and PEG (6000) in the presence of stannous octoate at 130 °C for 56 hr. The degradation behavior of the copolymers was investigated in a pH 7.4 phosphate buffer solution at 37 ±1 °C. Various techniques such as weight, gel permeation chromatography, ¹H nuclear magnetic resonance, differential scanning calorimetry and X‐ray diffractometry were used to monitor the changes in water absorption, weight loss, molar mass, molar mass distribution, thermal properties and compositions. The results show that the hydrophilicity of copolymer was enhanced with increasing poly(ethylene oxide) content, which led to the PEG sequences fast release and an increase in weight loss of the copolymer. Bimodal chromatograms were detected in the degradation, which were attributed to the degradation mechanism of the partial crystalline polymer proceeding predominantly in amorphous zones. Copyright © 2000 John Wiley & Sons, Ltd.