Enhanced ionic conductivity in PEO/PMMA glassy miscible blends: Role of nano‐confinement of minority component chains

AC impedance spectroscopy was used to investigate the ionic conductivity of solution cast poly(ethylene oxide) (PEO)/poly(methyl methacrylate) (PMMA) blends doped with lithium perchlorate. At low PEO contents (below overlap weight fraction w^*), ionic conductivities are almost low. This could be due to nearly distant PEO chains in blend, which means ion transportation cannot be performed adequately. However, at weight fractions well above w^*, a significant increase in ionic conductivity was observed. This enhanced ionic conductivity mimics the PEO segmental relaxation in rigid PMMA matrix, which can be attributed to the accelerated motions of confined PEO chains in PMMA matrix. At PEO content higher than 20 wt % the conductivity measured at room temperature drops due to crystallization of PEO. However by increasing temperature to temperatures well above the melting point of PEO, a sudden increase of conductivity was observed which was attributed to phase transition from crystalline to amorphous state. The results indicate that some PEO/PMMA blends with well enough PEO content, which are structurally solid, can be considered as an interesting candidate for usage as solid‐state electrolytes in Lithium batteries. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 2065–2071, 2010     

Molecular mobility of substituted poly(p-phenylenes) characterized by a range of polymer relaxation techniques

The free volume and related mobility properties of substituted poly(p-phenylene) polymers are examined. The techniques used range from positron annihilation, dielectric relaxation, and dynamic mechanical spectroscopy to thermally stimulated currents. Fractional free volume is determined for the samples with different substituted side groups and related to the glass transition temperature. Bulkier groups lead to a greater fractional free volume and lower glass transition temperatures. Comparison of molecular relaxation times using the different characterization techniques demonstrates that there is strong coupling between motion of the main chain and the side groups, on which the dipoles reside. Intermolecular coupling between the main chains at the primary relaxation is shown in this work to be related to the nature of the side chains and resultant free volume, as are the temperature locations of local, secondary relaxations. A qualitative model describing the effect of regiochemistry on the motions and packing of these materials is also proposed. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 1465–1481, 1998     

Thermosetting polymer blends of unsaturated polyester resin and poly(ethylene oxide). I. Miscibility and thermal properties

The miscibility and thermal properties of polyethylene oxide(PEO)/oligoester resin (OER) blends and PEO/crosslinked polyester (PER) blends were studied by differential scanning calorimetry (DSC). The effect of quenching process on the crystallization behavior of PEO for these two systems were investigated and discussed in details. It has been found that a single, composition dependent glass transition temperature (T_g) was observed for all the blends, indicating that the two systems are miscible in the amorphous state at overall compositions. From the melting point depression of PEO, the interaction parameter χ₁₂ for PEO/OER blends and that for PEO/PER blends were found to be −1.29 and −2.01, respectively. The negative values of χ₁₂ confirmed that both PEO/OER blends and PEO/PER blends are miscible in the molten state. Quenching process has a greater hindrance on the crystallization of PEO/OER blends than on that of PEO/PER blends. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 3161–3168, 1997     

Investigating the effect of nanolayered silicates on blend segmental dynamics and minor component relaxation behavior in poly(ethylene oxide)/poly(methyl methacrylate) miscible blends

Polymer–silicate nanocomposites based on poly (ethylene oxide), PEO, poly(methyl methacrylate), PMMA, and sodium montmorillonite clay were fabricated and characterized to investigate the effect of nanolayered silicates on segmental dynamics of PEO/PMMA blends. X‐ray results indicate the formation of an exfoliated morphology in the nanocomposites. At low silicate contents, an enhancement in segmental dynamics of blend nanocomposites and also PEO, minor component in blend, is observed at temperature region below blend glass transition. This result can be attributed to the improvement of the confinement effect of rigid PMMA matrix on the PEO chains by introducing a low amount of layered silicates. On the other hand, at high silicate contents, an enhancement in segmental dynamics of blend nanocomposites and PEO is observed at temperature region above blend glass transition. This behavior could be interpreted based on the reduction of monomeric friction between two polymer components, which can facilitate segmental motions of blend components in nanocomposite systems. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

A DSC study of miscibility and phase separation in crystalline polymer blends of phenolphthalein poly(ether ether sulfone) and poly(ethylene oxide)

The miscibility of blends of phenolphthalein poly(ether ether sulfone) (PES-C) and poly(ethylene oxide) (PEO) was established on the basis of the thermal analysis results. Differential scanning calorimetry (DSC) studies showed that the PES-C/PEO blends prepared by casting from N,N-dimethylformamide (DMF) possessed a single, composition-dependent glass transition temperature (T_g), and thus that PES-C and PEO are miscible in the amorphous state at all compositions at lower temperature. At higher temperature, the blends underwent phase separation, and the PES-C/PEO blend system was found to display a lower critical solution temperature (LCST) behavior. The phase separation process in the blends has also been investigated by using DSC. Annealed at high temperatures, the PES-C/PEO blends exhibited significant changes of thermal properties, such as the enthalpy of crystallization and fusion, temperatures of crystallization and melting, depending on blend composition when phase separation occurred. These changes reflect different characteristics of phase structure in the blends, and were taken as probes to determine phase boundary. From both the thermal analysis and optical microscopy, the phase diagram of the blend system was established. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35 : 1383–1392, 1997     

Segmental and secondary dynamics in hydrogen‐bonded poly(4‐vinylphenol)/poly(methyl methacrylate) blends

Broadband dielectric spectroscopy was used to study the segmental (α) and secondary (β) relaxations in hydrogen‐bonded poly(4‐vinylphenol)/poly(methyl methacrylate) (PVPh/PMMA) blends with PVPh concentrations of 20–80% and at temperatures from ?30 to approximately glass‐transition temperature (T_g) + 80 °C. Miscible blends were obtained by solution casting from methyl ethyl ketone solution, as confirmed by single differential scanning calorimetry T_g and single segmental relaxation process for each blend. The β relaxation of PMMA maintains similar characteristics in blends with PVPh, compared with neat PMMA. Its relaxation time and activation energy are nearly the same in all blends. Furthermore, the dielectric relaxation strength of PMMA β process in the blends is proportional to the concentration of PMMA, suggesting that blending and intermolecular hydrogen bonding do not modify the local intramolecular motion. The α process, however, represents the segmental motions of both components and becomes slower with increasing PVPh concentration because of the higher T_g. This leads to well‐defined α and β relaxations in the blends above the corresponding T_g, which cannot be reliably resolved in neat PMMA without ambiguous curve deconvolution. The PMMA β process still follows an Arrhenius temperature dependence above T_g, but with an activation energy larger than that observed below T_g because of increased relaxation amplitude. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3405–3415, 2004     

结晶-非晶共混体系的结晶行为研究——PEO/PMMA与PEO/PVA共混物

用DSC和傅里叶红外(FTIR)光谱表征PEO/PMMA和PEO/PVA共混体系的结晶行为。发现PEO/PVA体系的结晶度与其组成的变化是一致的;而PEO/PMMA体系的结晶度随非晶组分增加而下降的速度,从与组成变化一致到比后者快,但又随时间而改变。对此结晶/非晶共混体系的结晶度随组成和时间而变化的现象,可用体系的玻璃化转变温度(T_g)来解释。     

Thermorheological complexity of poly(methyl methacrylate)/poly(vinylidene fluoride) miscible polymer blend: Terminal and segmental levels

Oscillatory shear rheometry data for a miscible blend of 20 wt % poly(vinylidene fluoride) (PVDF) in poly(methyl methacrylate) (PMMA) shows breakdown of time–temperature superposition for this blend. A comparison between glass transition temperature which PMMA chains sense in the blend and effective glass transition temperature of this component indicates that, the Lodge–McLeish model can describe terminal dynamics of PMMA. In addition, terminal dynamics of PVDF chains in the blend is similar to that of its pure state in agreement with the mentioned model. At segmental level, dynamic mechanical thermal analysis of four wholly amorphous blends suggests that cooperativity of molecular motions decreases upon addition of 30 and 40 wt % PVDF to PMMA. This behavior has been confirmed via calculation of degree of fragility which presumably is attributed to strong tendency of PVDF chains to self‐association rather than inter‐association with PMMA chains according to the FTIR results. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2860–2870, 2007     

Two calorimetric glass transitions do not necessarily indicate immiscibility: The case of PEO/PMMA

Differential scanning calorimetry has been used to examine blends of a poly(ethylene oxide) (PEO), M_n = 300 g/mol, and a poly(methylmethacrylate) (PMMA), M_n = 10,000 g/mol, across the complete composition range. The relatively low molar mass of the PEO minimizes interference from crystallization. In the midrange of composition, ～25–70% PEO, two broad, but distinct, glass transitions are resolved. These are interpreted as distinct glass transitions of the two components, as anticipated by the self‐concentration model of Lodge and McLeish. The composition dependence of the observed transitions is well described by the self‐concentration approach, using lengthscales of approximately two‐thirds of the Kuhn length. The results are compared with previous measurements on PEO/PMMA blends and other miscible systems. The principal, general conclusion is that one should actually expect two glass transitions in a miscible polymer blend or polymer solution; the rule of thumb that two transitions indicate immiscibility is incorrect. Furthermore, attempts to rationalize two transitions on the basis of incomplete segmental mixing, or other unspecified “nanoheterogeneity,” may not be justified in many cases. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 756–763, 2006     

Nanoheterogeneity in PEO/PMMA blends probed by 129Xe-NMR

Xenon has been used as a structural probe of solid poly(ethylene oxide)/atactic poly(methyl methacrylate) (PEO/PMMA) blends of concentrations 10/90 to 75/25. ¹²⁹Xe-NMR spectra at 293 K show significant changes in line width and chemical shift as the blend composition is varied. The ¹²⁹Xe spectra are interpreted in terms of exchange between amorphous single-phase PEO and PMMA domains. It is shown that a simple two-site exchange model can be used to calculate spectra which fit the experimental data over the whole concentration range. Xe exchange between blend subregions is demonstrated also by a two-dimensional NMR experiment. The PEO/PMMA results are compared to previously published poly(vinylidene fluoride)/PMMA ¹²⁹Xe spectra. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35: 2681–2688, 1997     

Investigation at the chain segmental level of the miscibility of poly(vinyl chloride)/atactic poly(methyl methacrylate) blends

We employed high‐resolution ¹³C cross‐polarization/magic‐angle‐spinning/dipolar‐decoupling NMR spectroscopy to investigate the miscibility and phase behavior of poly(vinyl chloride) (PVC)/poly(methyl methacrylate) (PMMA) blends. The spin–lattice relaxation times of protons in both the laboratory and rotating frames [T₁(H) and T_1ρ(H), respectively] were indirectly measured through ¹³C resonances. The T₁(H) results indicate that the blends are homogeneous, at least on a scale of 200–300 Å, confirming the miscibility of the system from a differential scanning calorimetry study in terms of the replacement of the glass‐transition‐temperature feature. The single decay and composition‐dependent T_1ρ(H) values for each blend further demonstrate that the spin diffusion among all protons in the blends averages out the whole relaxation process; therefore, the blends are homogeneous on a scale of 18–20 Å. The microcrystallinity of PVC disappears upon blending with PMMA, indicating intimate mixing of the two polymers. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2390–2396, 2001     

Miscibility and crystallization behavior in blends of poly(methyl methacrylate) and poly(vinylidene fluoride): Effect of star‐like topology of poly(methyl methacrylate) chain

A tetraarmed star‐shaped poly(methyl methacrylate) (s‐PMMA) was synthesized via atom transfer radical polymerization with 2‐bromoisobutyryl pentaerythritol as the initiator. For comparison, a linear PMMA with the identical molecular weight (l‐PMMA) was also prepared. The blends of the two PMMA samples with poly (vinylidene fluoride) (PVDF) were prepared to investigate the effect of macromolecular topological structure on miscibility and crystallization behavior of the binary blends. The behavior of single and composition‐dependent glass transition temperatures was found for the blends of s‐PMMA with PVDF, indicating that the s‐PMMA is miscible with PVDF in the amorphous state just like l‐PMMA. The miscibility was further evidenced by the depression of equilibrium melting points. It is found that the blends of s‐PMMA and PVDF displayed the larger k value of Gordon–Taylor equation than the blends of l‐PMMA and PVDF blends. According to the depression of equilibrium melting points, the intermolecular parameters for the two blends were estimated. It is noted that the s‐PMMA/PVDF blends displayed the lower interaction parameter than l‐PMMA/PVDF blends. The isothermal crystallization kinetics shows that the crystallization of PVDF in the blends containing s‐PMMA is faster than that in the blends containing the linear PMMA. The surface‐folding free energy of PVDF chains in the blends containing s‐PMMA is significantly lower than those in the blends containing l‐PMMA. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2580–2593, 2007     

Pressure–volume–temperature properties and free volume parameters of PEO/PMMA blends

Melt-miscible polymer blends of poly(ethylene oxide)/atactic poly(methyl methacrylate (PEO/a-PMMA)) were prepared by melt-mixing and characterized by pressure–volume–temperature (PVT) dilatometry in the pressure and temperature range of 0 to 200 MPa and 20 to 200°C, respectively. The PVT data were analyzed in terms of two equations of state (EOS). The empirical Tait EOS was applied in the glassy, semicrystalline, and equilibrium melt state, and the Simha-Somcynsky EOS theory was applied in the equilibrium melt and glassy state. The Simha-Somcynsky EOS theory contains a free volume function. The temperature, pressure, and composition dependence of the free volume fraction h calculated from the Simha-Somcynsky EOS theory was studied. As a function of blend composition we observe that the free volume fraction, thermal expansivity, and compressibility all deviate mainly positively from linearity while the specific volume deviates mainly negatively from linearity. These findings are reconciled with composition-dependent free volume parameters, the free volume and cell volume as well as with self- and cross-interaction parameters derived from the Simha-Somcynsky EOS theory as applied to polymer mixtures. Moreover, the pressure dependence of glass and melting transitions as well as crystallization kinetics have been investigated. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 1061–1080, 1998     

Thermal and mechanical behavior of amorphous and semi-crystalline poly(vinylidene fluoride)/poly(methyl methacrylate) blends

Various PVDF/PMMA (poly(vinylidene fluoride)/poly(methyl methacrylate)) blends were selected for mechanical testing in compression. At low PVDF content (less than 50/50 w/w), the blends remain amorphous and PVDF and PMMA are fully miscible. In PVDF-richer blends, PVDF crystallizes in part, leading to a PMMA-enriched homogeneous amorphous phase. In this study, the degree of crystallinity was set at equilibrium by appropriate annealing of the samples before testing. Mechanical analysis was focused on the low deformation range, and especially on the yield region. Depending on the test temperature and blend composition, three types of response were identified, depending on whether plastic deformation is influenced: 1) by the PMMA secondary relaxation motions, 2) by the PVDF/PMMA glass transition motions, or 3) by the crystallite-constrained PVDF chains.     

Physical ageing in poly(vinyl acetate) 1. Enthalpy relaxation

The enthalpy changes ΔH_∞ between a poly(vinyl acetate) glass formed by rapid cooling and the corresponding fully relaxed glass have been estimated at four temperatures below the glass transition. The values obtained were different to those expected by extrapolating liquid behavior below the glass transition and were found to agree well with the predictions of a simple expression for the combined main chain conformational and free volume contributions to enthalpy. Conformational contributions from the side chain alone were also considered but were not required to obtain agreement with experiment. It can be concluded that the side chains remained mobile below the glass transition and do not contribute to the heat capacity discontinuity at T_g. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35: 1107–1116, 1997     

PEO／PVP共混体系结晶行为

本文用WAXD、PLM、DSC方法研究了聚氧化乙烯(PEO)/聚乙烯基吡咯烷酮(PVP)共混体系的结晶行为,探索了两组分聚合物间相互作用及体系结晶度与非晶组分含量的关系。DSC研究表明PEO/PVP共混体系具有两个玻璃化转变温度,分别是纯组分的T_g,无相容性。应用Avrami和LH方程对其动力学参数进行了研究。偏光显微镜观察了共混物结构形态。     

Synthesis and characterization of a vinyl‐terminated benzoxazine monomer and its blends with poly(ethylene oxide)

A vinyl‐terminated benzoxazine (VB‐a), which could be polymerized through ring‐opening polymerization, was synthesized through the Mannich condensation of bisphenol A, formaldehyde, and allylamine. This VB‐a monomer was then subjected to blending with poly(ethylene oxide) (PEO), followed by thermal curing, to form poly(VB‐a)/PEO blends. The specific interactions, miscibility, morphology, and thermal properties of these blends were investigated with Fourier transform infrared (FTIR) spectroscopy, differential scanning calorimetry, dynamic mechanical analysis (DMA), and scanning electron microscopy (SEM). Before curing, we found that PEO was miscible with VB‐a, as evidenced by the existence of a single composition‐dependent glass transition temperature (T_g) for each composition. The FTIR spectra revealed the presence of hydrogen‐bonding interactions between the hydroxyl groups of poly(VB‐a) and the ether groups of PEO. Indeed, the ring‐opening reaction and subsequent polymerization of the benzoxazine were facilitated significantly by the presence of PEO. After curing, DMA results indicated that the 50/50 poly(VB‐a)/PEO blend exhibited two values of T_g: one broad peak appeared in the lower temperature region, whereas the other (at ca. 327 °C, in the higher temperature region) was higher than that of pristine poly(VB‐a) (301 °C). The presence of two glass transitions in the blend suggested that this blend system was only partially miscible. Moreover, SEM micrographs indicated that the poly(VB‐a)/PEO blends were heterogeneous. The volume fraction of PEO in the blends had a strong effect on the morphology. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 644–653, 2007     

Molecular weight dependence of phase behavior of PEO/P(EO‐b‐DMS) blends: Application of Sanchez‐Lacombe lattice fluid theory

Molecular weight dependence of phase separation behavior of the Poly (ethylene oxide) (PEO)/Poly(ethylene oxide‐block‐dimethylsiloxane) (P(EO‐b‐DMS)) blends was investigated by both experimental and theoretical methods. The cloud point curves of PEO/P(EO‐b‐DMS) blends were obtained by turbidity method. Based on Sanchez‐Lacombe lattice fluid theory (SLLFT), the adjustable parameter, (quantifying the interaction energy between different components), was evaluated by fitting the experimental data in phase diagrams. To calculate the spinodals, binodals, and the volume changes of mixing for these blends, three modified combining rules of the scaling parameters for the block copolymer were introduced. The calculated binodals with those modified combining rules show good agreement with the experimental data. Furthermore, the calculated volume changes during mixing decrease with increasing molecular weight of PEO, and the relationship between the volume changes and temperature is quite different for the mixtures with different molecular weight of PEO. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 452–459, 2008     

STUDIES OF THE CRYSTALLIZATION BEHAVIOR IN THE CRYSTALLINE/AMORPHOUS POLYMER BLENDS: POLY(ETHYLENE OXIDE)/POLY(METHYL METHACRYLATE) AND POLY(ETHYLENE OXIDE)/POLY(VINYL ACETATE)

The crystallization process of poly(ethylene oxide) (PEO)/poly(methyl methacrylate) (PMMA)and PEO/poly(vinyl acetate) (PVAc) blends has been characterized by Fourier Transform Infrared(FTIR) spectra in conjunction with Differential Scanning Calorimeter (DSC) measurements. Thecrystallinity of PEO varies consistently with PEO content in PEO/PVAc blends and the PEO/PMMAblends containing 50 wt% or less PMMA. For the PEO/PMMA blends containing 60 wt% ormore PMMA, the crystallinity of PEO decreases more than PEO content but develops with crystal-lization time. These results can be explained in terms of difference between the crystallization tem-perature (T_c) and glass transition temperature (T_g) of the blends as a function of content of amorphouscomponent.     

Miscibility and phase structure of binary blends of polylactide and poly(methyl methacrylate)

Blends of amorphous poly(DL‐lactide) (DL‐PLA) and crystalline poly(L‐lactide) (PLLA) with poly(methyl methacrylate) (PMMA) were prepared by both solution/precipitation and solution‐casting film methods. The miscibility, crystallization behavior, and component interaction of these blends were examined by differential scanning calorimetry. Only one glass‐transition temperature (T_g) was found in the DL‐PLA/PMMA solution/precipitation blends, indicating miscibility in this system. Two isolated T_g's appeared in the DL‐PLA/PMMA solution‐casting film blends, suggesting two segregated phases in the blend system, but evidence showed that two components were partially miscible. In the PLLA/PMMA blend, the crystallization of PLLA was greatly restricted by amorphous PMMA. Once the thermal history of the blend was destroyed, PLLA and PMMA were miscible. The T_g composition relationship for both DL‐PLA/PMMA and PLLA/PMMA miscible systems obeyed the Gordon–Taylor equation. Experiment results indicated that there is no more favorable trend of DL‐PLA to form miscible blends with PMMA than PLLA when PLLA is in the amorphous state. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 23–30, 2003