Evidences of phase separation in moisture‐cured poly(urethane urea)s by means of temperature modulated differential scanning calorimetry

The degree of phase separation in several moisture‐cured poly(urethane urea)s (PUUs) was studied by FTIR spectroscopy, wide angle X‐ray diffraction (WAXD), and temperature‐modulated differential scanning calorimetry (TMDSC). This latter technique was shown to be particularly useful in analysing the degree of phase separation in PUU polymers. Both phase mixing and phase segregation coexisted in the PUUs and the degree of phase separation increased as the urea hard segment (HS) content in the PUU increased. The maximum solubility of urea HSs into the polyol soft segments (SSs) was achieved for 50 wt % urea HS content in diol‐based PUUs, whereas for triol‐based PUUs the highest solubility between HS and SS was reached for lower urea HS amount. Finally, the higher the urea HS content the higher the extent of phase separation in the PUU. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 3034–3045, 2007     

FTIR快速跟踪聚氨酯脲的反应注射成型研究

ＦＴＩＲ快速跟踪聚氨酯脲的反应注射成型研究罗宁，潘肇琦，王得宁，应圣康（华东理工大学材料科学研究所，上海，２００２３７）关键词聚氨酯脲，红外光谱，反应注射成型，动力学，相分离反应注射成型（ＲＩＭ）是生产聚氨酯制品的重要技术。以二醇扩链的聚氨酯的ＲＩＭ...     

Preparation and characterization of waterborne poly(urethane urea) with well‐defined hard segments

A series of polyester‐based poly(urethane urea) (PUU) aqueous dispersions with well‐defined hard segments were prepared from polyester polyol, 4,4′‐diphenylmethane diisocyanate, dimethylolpropionic acid, 1,4‐butanediol, isophorone diisocyanate, and ethylenediamine. These anionic‐type aqueous dispersions had good dispersity in water and were stable at the ambient temperature for more than 1 year. For these aqueous dispersions, the particle size decreased as the hard‐segment content increased, and the polydispersity index was very narrow (<1.10). Films prepared with the PUU aqueous dispersions exhibited excellent waterproof performance: the amount of water absorption was as low as 5.0 wt %, and the contact angle of water on the surface of this kind of film was as high as 103° (this led to a hydrophobic surface). The water‐resistant property of these waterborne PUU films could be well correlated with some crystallites and ordered structures of the well‐defined hard segments formed by hydrogen bonding between the urethane/urethane groups and urethane/ester groups, as well as the degree of microphase separation between the hard and soft segments in the PUU systems. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2606–2614, 2005     

Effect of the crosslink density on the morphology and properties of reaction‐injection‐molding poly(urethane urea) elastomers

The effect of the crosslink density on the morphology and properties of reaction‐injection‐molding poly(urethane urea) (PUU) elastomers was investigated. Fourier transform infrared spectroscopy data showed that the linear and crosslinked PUU had entirely different hard‐domain sizes and hard‐segment ordering. A study of the morphology indicated that an increase in the crosslink density increased microphase mixing. Differential scanning calorimetry studies indicated that the hard‐segment initial glass‐transition temperature was independent of the crosslink density. The glass‐transition temperature of the soft segment was highest when the network was perfect. The tensile‐strength behavior showed that the mechanical properties of PUU reached a maximum when the network was perfect. The increase in the resilience of the crosslinked PUU elastomer was higher than that of the linear PUU elastomer with an increase in temperature, and the reduction of the hardness of the former was also higher than that of the latter. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1126–1131, 2004     

Morphology,electrical resistance,electromagnetic interference shielding and mechanical properties of functionalized MWNT and poly(urea urethane) nanocomposites

The functionalized multi‐walled carbon nanotubes (MWNT) had been prepared by free radical reaction with vinyltriethoxysilane. Polydimethylsiloxane (PDMS)‐based poly(urea urethane) (PUU) was also synthesized. PUU was further end‐capped with aminopropyltriethoxysilane (A‐silane), or with phenyltrimethoxysilane (P‐silane). Fourier transform infrared (FTIR), Raman spectra and thermogravimetric analysis (TGA) confirmed the functionalization of MWNT. The M_n and M_w of PUU were 85,123 and 235,876 g/mol, respectively. Both A‐silane end‐capped PUU and P‐silane end‐capped PUU showed improved dispersion of MWNT compared with that of PUU and MWNT. Moreover, the reduced discrepancy of surface electrical resistance of the two sides of the MWNT/PUU nanocomposite film was found due to the homogeneous dispersion of MWNT. The microwave absorption and tensile strength of MWNT/PUU were also improved by the well dispersion of MWNT in PUU matrix. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1096–1105, 2006     

Synthesis and characterization of poly(dimethylsiloxane‐urethane) elastomers: Effect of hard segments of polyurethane on morphological and mechanical properties

A series of poly(dimethylsiloxane‐urethane) elastomers based on hexamethylenediisocyanate, toluenediisocyanate, or 4,4′‐methylenediphenyldiisocyanate hard segment and polydimethylsiloxane (PDMS) soft segment were synthesized. In this study, a new type of soft‐segmented PDMS crosslinker was synthesized by hydrosilylation reaction of 2‐allyloxyethanol with polyhydromethylsiloxane, using Karstedt's catalyst. The synthesized soft‐segmented crosslinker was characterized by FT‐IR, ¹H, and ¹³C NMR spectroscopic techniques. The mechanical and thermal properties of elastomers were characterized using tensile testing, thermogravimetric analysis, differential scanning calorimetry (DSC), and dynamical mechanical analysis measurements. The molecular structure of poly(dimethylsiloxane‐urethane) membranes was characterized by ATR‐FTIR spectroscopic techniques. Infrared spectra indicated the formation of urethane/urea aggregates and hydrogen bonding between the hard and soft domains. Better mechanical and thermal properties of the elastomers were observed. The restriction of chain mobility has been shown by the formation of hydrogen bonding in the soft and hard segment domains, resulting in the increase in the glass‐transition temperature of soft segments. DSC analysis indicates the phase separation of the hard and soft domains. The storage modulus (E′) of the elastomers was increasing with increase in the number of urethane connections between the hard and soft segments. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2980–2989, 2006     

Synthesis of poly(urethane urea) by in situ polymerization inside stone

The first synthesis of poly(urethane urea) by in situ polymerization inside stone was successfully carried out. Poly(propylene glycol), isophorondiisocyanate, and a catalyst [tin(II) ethyl hexanoate, aluminum acetylacetonate, or zirconium acetylacetonate] were mixed with acetone in petri dishes, and tuff samples were placed in the dishes at room temperature. The effects of the comonomer ratio, catalyst, and catalyst concentration on the chemical structure of the synthesized poly(urethane urea) were investigated. The poly(urethane urea) distribution inside the tuff and the related morphology were also analyzed, as well as the reversibility of the performed treatments. Finally, the effects of the in situ polymerization polymer on the properties of the stone, such as water capillary absorption and permeability to water vapor, were assessed. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 542–552, 2005     

Octa(maleimido phenyl) silsesquioxane copolymers

Octa(maleimido phenyl) silsesquioxane (OMPS) was prepared from octa(aminophenyl) silsesquioxane (OAPS) and maleic anhydride. Initially, octaphenyl silsesquioxane was prepared, and it was nitrated to obtain octa(nitrophenyl) silsesquioxane; subsequently, reduction was carried out to obtain OAPS. These compounds were characterized with Fourier transform infrared, NMR, gel permeation chromatography, and wide‐angle X‐ray diffraction. Differential scanning calorimetry scans of OMPS showed an exotherm above 100 °C, and it was attributed to the curing. The peak maximum temperature depended on the heating rate. Both Ozawa's and Kissinger's methods were used to determine the activation energy for the curing reaction, which was approximately 29 kcal/mol. OMPS was copolymerized with various molar percentages of (1) N,N′‐p‐phenylenedimaleimide (PPMI) and (2) urethane methacrylate (UMA) by thermal and free‐radical polymerization, respectively. The copolymers were characterized with differential scanning calorimetry, dielectric analysis, thermogravimetric analysis, and wide‐angle X‐ray diffraction. In the PPMI and UMA copolymer series, the glass‐transition temperature increased with an increase in the OMPS concentration. The permittivity of the UMA copolymers decreased and tan δ increased with an increase in the OMPS concentration. In air and nitrogen atmospheres, the thermal stability of the PPMI and UMA copolymers increased with an increase in the OMPS concentration. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2483–2494, 2005     

Molecular mobility of free‐radical‐functionalized carbon‐nanotube/siloxane/poly(urea urethane) nanocomposites

Multiwalled carbon nanotubes (MWNTs) were functionalized by a free‐radical reaction of vinyltriethoxysilane and were blended with poly(urea urethane) (PUU) containing poly(dimethylsiloxane) as a soft segment. PUU was end‐capped with aminopropyltriethoxysilane (A‐silane) or phenyltriethoxysilane (P‐silane).A‐silane‐end‐capped PUU was covalently bonded to functionalized MWNTs, whereas P‐silane‐end‐capped PUU was noncovalently bonded to pristine MWNTs by a π–π interaction. Fourier transform infrared, Raman spectra, and thermogravimetric analysis confirmed the functionalization of MWNTs. The results showed that the optimal reaction time of the functionalization of MWNT was 8 h, and the organic content of the modified carbon nanotubes reached 35.22%. Solid‐state nuclear magnetic resonance and dynamic mechanical analysis were used to investigate the molecular structure and molecular mobility of the carbon‐nanotube/PUU nanocomposites. A‐silane PUU covalently bonded to MWNTs showed a considerable reduction in the molecular motion of the soft segment, which led to the glass‐transition temperature decreasing from ?117 to ?127 °C as MWNTs were incorporated. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 6084–6094, 2005     

Synthesis and characterization of semicrystalline cycloaliphatic polyester/poly(dimethylsiloxane) segmented copolymers

High molecular weight poly(dimethylsiloxane)/semicrystalline cycloaliphatic polyester segmented copolymers based on dimethyl-1,4-cyclohexane dicarboxylate were prepared and characterized. The copolymers were synthesized using a high trans content isomer that afforded semicrystalline morphologies. Aminopropyl-terminated poly(dimethylsiloxane) (PDMS) oligomers of controlled molecular weight were synthesized, end capped with excess diester to form a diester-terminated oligomer, and incorporated via melt transesterification step reaction copolymerization. The molecular weight of the polysiloxane and chemical composition of the copolymer were systematically varied. The polysiloxane segment was efficiently incorporated into the copolymers via an amide link and its structure was unaffected by low concentrations of titanate transesterification catalyst, as shown by control melt experiments. The homopolymer and copolymers were characterized by solution, thermal, mechanical, and surface techniques. The segmented copolymers were microphase separated as determined by differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), and by transmission electron microscopy (TEM). It was demonstrated that relatively short poly(dimethylsiloxane) segment lengths and compositions were required to maintain single phase melt polymerization conditions. This was, in fact, the key to the successful preparation of these materials. The copolymers derived from short poly(dimethylsiloxane) segments demonstrated good mechanical properties, melt viscosities representative of single phase polymer melts, and were easily compression molded into films. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 3495–3506, 1997     

Preparation and electromagnetic interference shielding characteristics of novel carbon‐nanotube/siloxane/poly‐(urea urethane) nanocomposites

Poly(urea urethane) (PUU) with a poly(dimethylsiloxane) soft segment was synthesized. Different types of conductive fillers—carbon nanotube (CNT), silver‐coated carbon nanotube (CNT–Ag), and nickel‐coated carbon nanotube (CNT–Ni)—were blended with PUU to form partially conductive polymer composites. The results showed that highly conductive metals could improve the conductivity of CNTs significantly. When the filler contents were 3, 4, and 5 parts per hundred parts of resin (phr), the PUU/CNT composites possessed electromagnetic interference shielding effectiveness (SE) at 8.5, 28.4, and 26.0 dB as the electromagnetic wave frequencies were 12.3, 16.2, and 15.9 GHz, respectively. SE of the composites that contained CNT–Ni and CNT–Ag increased with the filler loading. At the same modified‐CNT loading, the CNT–Ni‐filled composites had a higher SE than those filled with CNT–Ag. Tensile stresses ranged from 5.7 to 15.6 MPa (a 177.3% increase) when the CNT concentration reached 8 phr. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 345–358, 2005     

Star-graft copolymers. Synthesis of amphiphilic graft copolymers with star-branched poly(oxyethylene) side chains

The synthesis of novel amphiphilic star-graft (SG) copolymers containing hydrophilic poly(oxyethylene) (PEO) side chains attached to a hydrophobic backbone by multifunctional entity is reported. In a first step poly(phthalimidoacrylate-co-styrene) was converted into polymers containing different number of multifunctional branching cites distributed along the main chain by partial aminolysis of the phthalimidoacrylate units with tris(hydroxymethyl)aminomethane. In the second step, these reactive copolymers yielded SG copolymers with different number of star-shaped PEO side groups by reaction with isocyanato terminated methoxy–PEO. The copolymers were characterized by size-exclusion chromatography, IR-, and NMR-spectroscopy. Their thermal properties were examined by thermal gravimetric analysis and differential scanning calorimetry. The studies indicate that the grafting degree and hydrogen bonding determine to a great extent the behavior of the SG copolymers in solid state and in solution. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 673–679, 1997     

Design,synthesis and characterization of novel poly(urethane-urea) based on a macrodiol from poly(lactic acid) and poly(p-dioxanone)

A series of novel poly(urethane-urea)(PUU) was synthesized from poly(lactide-co-p-dioxanone) macrodiol(HO-P(LA-co-PDO)-OH), hexamethylene diisocyanate(HDI) and butanediamine(BDA).The obtained PUU,which is recorded as P(LA-co-PDO)-PUU here,may demonstrate enhanced phase separation and thus improved shape memory property.FTIR was employed to characterize the copolymers,and the effects of NCO/OH molar ratios on T_g of PUU was investigated by means of differential scanning calorimetry (DSC).The results revealed the successful synthesis of P(LA-co-PDO)-PUU.In addition,the T_g of P(LA-co-PDO)-PUU increased from 37.9℃to 44.2℃with the increase NCO/OH ratios from 1.1 to 1.2.The P(LA-co-PDO)-PUU with T_g close to body temperature will have potential applications as shape memory polymers in biomedical fields,especially in minimally invasive surgery.     

Coupling of α,ω-dichloropoly(methylphenylsilane) and living poly(styryllithium). Study of the coupling reaction

Both di- and triblock copolymers consisting of polystyrene (PS) in conjunction with poly(methylphenylsilane) (PMPS) have been successfully prepared by coupling of α,ω-dichloro-PMPS with poly(styryllithium). The study of this reaction has shown a sudden limitation of the coupling yield, which however depends on the PS block length. Both the polymer concentration and the solvent have also an effect on the coupling reaction. Morphology of the PS-PMPS block copolymers has been observed by transmission electron microscopy. Very complex morphologies have been reported more likely as the result of the competition between the phase separation induced by PS and PMPS immiscibility and the tendency of PMPS to form ordered structures. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 1939–1948, 1997     

Easily grafted polyurethanes with reactive main chain functional groups. Synthesis,characterization, and antithrombogenicity of poly(ethylene glycol)-grafted poly(urethanes)

A novel synthesis of poly(ethylene glycol) (PEG)-grafted poly(urethanes) (PURs) is described based on a precursor PUR containing free amino groups in the main chain. Three different poly(urethane) backbones were prepared: a homopoly(urethane) comprised of N-Bocdiethanolamine (BDA) and 4,4′-methylenebis(phenyl isocyanate) (MDI), a copoly(urethane) (COPUR) consisting of BDA, N-benzyldiethanolamine and MDI, and a poly(urethane urea) (PUU) that was prepared from BDA, MDI, and ethylenediamine as the chain extender. The M_n of these poly(urethanes) ranged from 32,000 to 72,000 g/mol. PEG (750, 1,900, and 5,000 g/mol) was grafted onto the boc-deprotected poly(urethanes) via the chloroformate. Films of the polymers were spin cast from dilute solutions, annealed, and the surfaces analyzed by goniometry. Water contact angle data indicates increasing PEG surface coverage of the poly(urethanes) with increasing PEG molecular weight. Reorientation of the polymer films is evidenced by contact angle hysteresis. Polymer thrombogenicity, which was studied using blood perfusion experiments, shows that COPUR-g-PEG5000 and PUU-g-PEG5000 exhibit very little platelet adhesion. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 3441–3448, 1999     

二胺扩链剂对RIM聚氨酯－脲弹性体的结构与性能的影响

采用实验室小型ＲＩＭ机制备了一组不同芳香二胺扩链的嵌段聚氨酯－脲（ＰＵＵ）弹性体，借助于ＩＲ、ＤＳＣ、ＤＭＴＡ、ＳＥＭ以及拉伸试验等测试手段对其结构与性能进行了研究。     

Novel method for the preparation of poly(urethane–imide)s and their properties

A polymer blend consisting of polyimide (PI) and polyurethane (PU) was prepared by means of a novel approach. PU prepolymer was prepared by the reaction of polyester polyol and 2,4-tolylenediisocyanate (2,4-TDI) and then end-capped with phenol. Poly(amide acid) was prepared from pyromellitic dianhydride (PMDA) and oxydianiline (ODA). A series of oligo(amide acid)s were also prepared by controlling the molar ratio of PMDA and ODA. The PU prepolymer and poly(amide acid) or oligo(amide acid) solution were blended at room temperature in various weight ratios. The cast films were obtained from the blend solution and treated at various temperatures. With the increase of polyurethane component, the films changed from plastic to brittle and then to elastic. The poly(urethane–imide) elastomers showed excellent mechanical properties and moderate thermal stability. The elongation of films with elasticity was more than 300%. The elongation set after the breaking of films was small. From the dynamic mechanical analysis, all the samples showed a glass transition temperature (T_g) at ca. −15°C, corresponding to T_g of the urethane component, suggesting that phase separation occurred between the two polymer components, irrespective of polyimide content. TGA and DSC studies indicated that the thermal degradation of poly(urethane–imide) was in the temperature range 250–270°C. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 3745–3753, 1997     

Use of blowing catalysts for integral skin polyurethane applications in a controlled molecular architectural environment: Synthesis and impact on ultimate physical properties

Polyurethane elastomers of a controlled molecular architecture were synthesized using a two‐step polymerization technique. The building blocks of the elastomeric materials included urea–urethane prepolymers end‐capped with diisocyanate groups and had an exact number of urea groups at both ends. Two‐dimensional bifurcated hydrogen‐bonding networks incorporating the urea groups were, with differential scanning calorimetric and dynamic mechanical thermal analyzer techniques, responsible for the increase in the glass‐transition temperature (T_g) of the hard block and sharp interface morphology between the pure “hard” domains and pure “soft” domains. The higher extent of the phase separation between the two phases contributed to higher elastic moduli for the hard blocks and higher tensile strength for the elastomeric samples. Higher elongation values were attributed to the liberation of the elastomeric chain ends that otherwise would have been constrained in the interface region. The higher T_g values of the hard blocks corresponded to an increase in the hardness values and a decrease in the tear‐strength values. The increase in the amount of urea groups within the hard segments, as a result of the increased amount of water and blowing catalyst, resulted in elastomeric foams with higher open‐cell content. This resulted in lower resilience values as measured using the pendulum rebound test and was attributed to the ability of the open cells to absorb and dissipate energy. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2526–2536, 2002     

13C-NMR spectroscopy study of polyurethane obtained from azide hydroxyl-terminated polymer cured with isophorone diisocyanate (IPDI)

Chemical structure investigations of polyurethane binders based on difunctional linear glycidyl azide polymer (GAP) cured with isophorone diisocyanate (IPDI) were performed using ¹³C-NMR spectroscopy in solution. Chemical functions such as urethane, urea, allophanate, and biuret were all expected to be detected in these polymeric binders. ¹³C-NMR assignment of the C O urethane and urea functions were found in these polymers as determined by using model compounds of IPDI. The ¹³C-NMR data gathered in this article can be considered as basic parameters for further characterization of polyurethane structure based on IPDI. Also, ¹³C CP MAS NMR spectra of GAP-IPDI-based polymers were carried out to identify the various chemical functions present in solid polyurethane elastomer. In addition, the curing evolution of a GAP-IPDI-based polymer at 50 and 80°C in bulk was monitored, and the reaction path of the binder was readily determined. Some conclusions on the effects of the cure catalyst and the curing temperature were also drawn. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 2991–2998, 1997     

Polyisobutylene‐based polyurethanes. IX. synthesis,characterization, and properties of polyisobutylene‐based poly(urethane‐ureas)

Polyisobutylene (PIB)‐based polyurethanes (PUs) exhibit unparalleled hydrolytic‐oxidative‐biologic stability and are melt processible, however, their mechanical (strength) properties are modest mainly due to insufficient H bonds. We posited and demonstrate that the ultimate properties of PIB‐PUs are enhanced, while their melt processibility is maintained, by the judicious introduction of urea linkages, i.e., strong bifurcated H bonds, in the chain. The incorporation of bifurcated H bonds in PIB‐PUs was achieved by using the conventional butane diol chain extender (CE) in combination with controlled amounts of amino alcohol as co‐chain extender (co‐CE). Polyurethanes containing both urethane and urea linkages are polyurethane‐ureas (PUU). Specifically, PIB‐PUUs prepared with PIB‐diol/MDI together with 80/20 mole % butane diol/amino butanol exhibited ～30 MPa tensile strength, ～550% elongation, ～80 Shore A hardness, and ～137 °C flow temperature. Other amino alcohols, i.e., amino ethanol, ‐propanol, and ‐hexanol, were less effective co‐CEs. ¹H‐NMR and FT‐IR spectroscopies indicate the presence of bifurcated H bonds in PIB‐PUUs prepared with CE/co‐CE combinations. Characterization by differential scanning calorimetry, thermogravimetric analysis, dynamic mechanical thermal analysis, and creep experiments also suggest bifurcated H bonds in PIB‐PUU. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2361–2369