Supramolecular structure and properties of high strength regenerated cellulose films

Water-swollen cellulose films prepared from LiOH/urea solution were uniaxially drawn to investigate the effect of orientation on their supramolecular structure and properties. Their structures and properties were investigated with X-ray diffraction, atomic force microscopy and tensile testing. The results revealed that the drawing process led to substantial reorientation of the cellulose molecular chains, resulting in a significant improvement of their mechanical properties and water-resistance. With an increase of the drawn ratios from 1 to 1.22, the tensile strength of the films at dry and wet states increased from 89 to 213 MPa and 2.9 to 33.9 MPa, respectively. Furthermore, the drawn cellulose films also exhibited good biocompatibility with the capability of supporting cell adhesion and proliferation.     

Structure and properties of regenerated cellulose/tourmaline nanocrystal composite films

Nanocomposite films were successfully prepared from cellulose and tourmaline nanocrystals with mean diameters of 70 nm in a 1.5 M NaOH/0.65 M thiourea aqueous solution by coagulation with 5 wt % CaCl₂ and then a 3 wt % HCl aqueous solution for 2 min. The structure and properties of the composite films were characterized by X‐ray diffraction, scanning electron microscopy, transmission electron microscopy, dynamic mechanical analysis (DMA), differential scanning calorimetry (DSC), and tensile testing. The results indicated that the tourmaline nanocrystals were dispersed in a cellulose matrix, maintaining the original structure of the nanocrystals in the composite films. The loss peaks (tan δ) in the DMA spectra and the decomposition temperatures in the DSC curves of the composite films were significantly shifted toward low temperatures, suggesting that the nanocrystals broke the partial intermolecular hydrogen bonds of cellulose, and this led to a reduction in the thermal stability. However, the nanocomposite films exhibited a homogeneous structure and dispersion of the nanocrystals. When the tourmaline content was in the range of 4–8 wt %, the composite films possessed good tensile strength (92–107 MPa) and exhibited obvious antibacterial action against Staphylococcus aureus. This work provides a potential way of preparing functional composite films or fibers from cellulose and nanoinorganic particles with NaOH/thiourea aqueous solutions. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 367–373, 2004     

Optical and mechanical properties of polyurethane/surface-modified nanocrystalline cellulose composites

in order to improve the optical and mechanical performances of waterborne polyurethane （WPU）, nanocrystalline cellulose （NCC）/WPU composites were synthesized in this study. NCC （prepared by acid hydrolysis of cotton fiber） was modified by （3-aminopropyl）triethoxysilane （APTES） to enhance its compatibility with WPU, and the surface-modified NCC was characterized by grafting ratio, crystallinity and contact angle （CA）. NCC/WPU composites were examined by scanning electron microscopy （SEM）, X-ray powder diffraction （XRD） and thermogravimetric analysis （TG）. The anti-yellowing property, specular gloss, pencil hardness, and abrasion resistance of NCC/WPU composites were investigated by the methods of Chinese National Standards GB/T 23999-2009, GB/T 9754-2007, GB/T 6739-2006 and GB/T 1768-2006, respectively. The results showed that the grafting ratio of NCC modified by 6% APTES was 36.01% and the crystallinity of modified NCC was decreased with the enhancement of APTES. CA of the modified NCC was decreased by 28.8% and the nanoparticles were homogeneously dispersed in the WPU matrix. The XRD patterns of the NCC/WPU composites were relatively steady, while the thermal stability of the composites was enhanced by 6.7% with 1.0 wt% modified NCC. Modified NCC affected the specular gloss of NCC/WPU composites more obviously than the anti-yellowing property. The pencil hardness of NCC/WPU composites was increased from 2H to 4H by addition of NCC and the abrasion resistance of the composites was enhanced significantly. In general, NCC/WPU composites showed significant improvements in the optical and mechanical performances.     

Effects of molecular weight of nitrocellulose on structure and properties of polyurethane/nitrocellulose IPNs

Semi‐interpenetrating polymer network (semi‐IPN) coatings were prepared by using castor oil‐based polyurethane (PU) and nitrocellulose (NC) with various viscosity‐average molecular weights (M_η) from 6 × 10⁴ to 42 × 10⁴, and coated on a regenerated cellulose (RC) film to obtain water‐resistant film. The PU/NC coatings and coated films, which were cured at 80°C for 5 min and 2 min, respectively, were investigated by infrared (IR) and ultraviolet (UV) spectroscopy, X‐ray diffraction, swelling test, strength test, dynamic mechanical thermal analysis (DMTA), differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA). The results show that the crosslink densities of the PU/NC semi‐IPNs were smaller than that of pure PU, and decreased with the decrease of M_η of nitrocellulose (NC M_η), indicating NC molecules cohered intimately with PU, and hindered the PU network formation. The physical and mechanical properties of the films coated with PU/NC coatings were significantly improved. With the increase of NC M_η, the strength and thermal stability of the coated films increased, but the pliability, water resistivity, and optical transmission decreased slowly. The PU/NC coating with low NC M_η more readily penetrated into the RC film, and reacted with cellulose, resulting in a strong interfacial bonding and dense surface caused by intimate blend of PU/NC in the coated films. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1623–1631, 1999     

Controlled loading and release of methylene blue from LbL polyurethane/poly(acrylic acid) film

The layer‐by‐layer (LbL) assembled multilayer films are widely used in the biomedical field for the controlled drug delivery. Here, multilayer films were assembled by LbL technique through alternating deposition of cationic polyurethane (PU) and poly(acrylic acid) (PAA) on glass slides. Methylene blue (MB) was used as a model drug to investigate the loading and release ability of the prepared multilayer film. The results showed that the loading rate and loading amount of MB were greatly influenced by pH value of the dye solution, and the release rate of MB was controlled both by ionic strength and pH value of immersing solution. The result also indicated that the film had a good reversibility of drug loading and release. It suggested that the PU/PAA multilayer film had potential applications in drug delivery and controlled release. Copyright © 2011 John Wiley & Sons, Ltd.     

Bionanocomposite based on cellulose nanowhisker from oil palm biomass-filled poly(lactic acid)

Cellulose nanowhiskers (CNW) extracted from plant fibers exhibit remarkable properties that make them suitable for use in the development of bionanocomposites. CNW have demonstrated the capability to enhance the properties of a polymer matrix at low filler loading. In this study, poly (lactic acid) (PLA) bionanocomposites were prepared using the solution casting technique, by incorporating the PLA with the CNW obtained from an oil palm empty fruit bunch (OPEFB). Fourier transform infrared spectroscopy showed no significant changes in the PLA peak positions, which indicates that incorporating the CNW into the PLA did not result in any significant changes in the chemical structure of the PLA. Thermogravimetric analysis, on the other hand, revealed that the bionanocomposites (PLA-CNW) had better thermal stability than the pure PLA. The tensile strength of PLA-CNW increased by 84% with the addition of 3 parts of CNW per hundred resins (phr), and decreased thereafter. Moreover, a linear relationship was observed between the Young's modulus and CNW loading. Elongation at break, however, decreased with the addition of 1-phr CNW, and remained constant with further addition. Transmission electron microscopy revealed that agglomeration of CNW occurred at 5-phr loading, consistent with the tensile strength results. Overall, the CNW obtained from OPEFB can enhance the tensile and the thermal properties of bionanocomposites.     

Hydrogen bonding,mechanical properties,and surface morphology of clay/waterborne polyurethane nanocomposites

A novel clay/waterborne polyurethane (WPU) nanocomposite was synthesized from polyurethane and saponite organoclay. The clay was organically modified with various swelling agents, the effect of which has been investigated. Hydrogen bonding between organic and inorganic materials was characterized with Fourier transform infrared (FTIR) spectroscopy. The results implied that hydrogen bonding increased when organoclay was added. Mechanical and wear property studies revealed that introducing clay into waterborne polyurethane will enhance the Young's modulus (from 56 to 126 MPa), the maximum stress (from 3.9 to 7.6 MPa), and the elongation at break (from 27.7 to 58.7%) of the nanocomposite by a factor of two, whereas the wear loss will be only one third of the neat waterborne polyurethane. Atomic force microscopy (AFM) was used to analyze the surface morphology of the nanocomposite. An AFM microphotograph showed that the surface of the clay/waterborne polyurethane nanocomposite was smoother when clay was added in waterborne polyurethane. The average roughness (R_a) decreased from 1.00 to 0.12. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1–12, 2005     

Molecular and crystal structure of cellulose acetate dipropanoate (CADP, 6-O-acetyl-2,3-di-O-propanoyl cellulose)

The molecular and crystal structure of cellulose acetate dipropanoate (CADP, 6-O-acetyl-2,3-di O-propanoyl cellulose) has been determined by using a constrained linked-atom least-squares refinement method, combined with X-ray and electron diffractograms and stereochemical refinement. The diffraction analysis indicated that CADP crystallized in a P2 ₁ monoclinic space group with unit cell parameters:a =1.088 nm,b (unique axis)=1.593 nm,c (fibre axis)=1.509 nm and =94.1°. The best model derived from combining the stereochemical refinement with the diffraction intensities gave R=0.217 (R=0.195) for the three-dimensional information from the X-ray fibre diagram and R=0.198 for the base plane data resulting from electron diffraction analysis. In the model, the crystal structure of CADP consisted of a system of right-handed threefold helices packed in an antiparallel fashion, with two molecules passing through the unit cell.     

Analysis and evaluation of biobased polyester of PTT/PBAT blend: thermal,dynamic mechanical,interfacial bonding,and morphological properties

Novel blends were prepared from biobased poly(trimethylene terephthalate) (PTT) and poly(butylene adipate‐co‐terephthalate) (PBAT) using a twin screw extrusion process as a function of different weight ratios. Thermal stability, mechanical, and interfacial properties of PTT/PBAT blends were investigated using a thermogravimetric analyzer and mechanical analyzer. Phase behavior and surface morphology of the blends were characterized using scanning electron microscopy. Interfacial bonding value of the PTT/PBAT blend was evaluated from the Pukanszky empirical relationship. Viscoelastic properties of PTT/PBAT blends were investigated using the dynamic mechanical analyzer. PTT/PBAT blend exhibited higher thermal stability than the neat PTT matrix. The entire blend showed better interfacial adhesion between the matrixes. Storage and loss modulus of the PTT/PBAT blend reduces with increasing PBAT content. PTT/PBAT blend exhibited higher impact energy than the neat PTT matrix, because of its flexible and amorphous nature of PBAT polymer and increasing toughness. Copyright © 2016 John Wiley & Sons, Ltd.     

Molecular and crystal structure of cellulose propanoate diacetate (CPDA, 2,3-di-O-acetyl-6-O-propanoyl cellulose)

The molecular and crystal structure of cellulose propanoate diacetate (CPDA, 2,3-di-O-acetyl-6-O-propanoyl cellulose) has been determined through combined X-ray fibre diagrams and electron diffraction patterns of single crystal analysis, aided by stereochemical restraints by using a constrained linked-atom least-squares refinement. The unit cell of CPDA is orthorhombic with space group P2 ₁2₁2₁ and parameters:a =1.239 nm,b =2.498 nm and c (fibre axis)=1.044 nm. Based on these data, coupled with the observed density of the crystals, there are four chains per unit cell, distributed in two antiparallel pairs of parallel chains, and the independent repeat is the disaccharide unit in each chain. A preliminary CPDA disaccharide unit was derived based on the centre residue of cellotriose undeca-acetate, and this model was refined through a conformational analysis. The best model obtained by combining the stereochemical refinement with the diffraction intensities gave R=0.272 (R=0.259) for the three-dimensional information from the X-ray fibre diagram and R=0.248 (R=0.246) for the base plane data resulting from electron diffraction analysis.     

Preparation and characterization of cellulose and konjac glucomannan blend film from ionic liquid

Blend films from cellulose and konjac glucomannan (KGM) in room temperature ionic liquid 1‐allyl‐3‐methylimidazolium chloride were satisfactorily prepared by coagulating with water. The composition of the blend films was gravimetrically analyzed, and the compatibility of the two natural polymers was characterized by Fourier transform infrared spectroscopy and wide‐angle X‐ray diffraction. The results indicate good compatibility and strong interactions between cellulose and KGM, resulting in almost no loss of the water‐soluble KGM from the blend films even after the water coagulating and washing. However, microstructure analyses portrayed phase separations in the blend films, namely, egg‐like new phase particles were embedded in a continuous matrix base (MB). Phase diagram analysis and differential scanning calorimetry of the phase inversion coagulation process suggest that relative low molecular mass part of both cellulose and KGM formed the continuous MB, whereas the egg‐like new phase particles were super patterns of relative high molecular mass of both polymers, which played an important role in strengthening the blend material. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1686–1694, 2009     

Separation and enzymatic degradation of blend films of poly(L-lactic acid) and cellulose

Blend films of poly(L -lactic acid) (PLLA) and cellulose with various composition was prepared by casting from trifluoroacetic acid solution. One hydroxyl group per each glucose unit was esterified by trifluoroacetic acid. The trifluoroacetyl group was hydrolyzed completely during the degradation. Weight losses for 90/10 and 75/25 PLLA/cellulose blends by proteinaze K were greatly increased compared with pure PLLA sample due to the large depression of the crystallinity of PLLA component, while cellulase was effective only for the degradation of pure cellulose film. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1861–1864, 1998     

Fluorescence staining and confocal laser scanning microscopy study of hydrogen-bonded poly(vinylpyrrolidone)/poly(acrylic acid) film

Poly(vinylpyrrolidone) (PVPON) and poly(acrylic acid) (PAA) were layer-by-layer (LBL) assembled to prepare the thin films based on hydrogen-bonding complexation. The hydrogen-bonded PVPON/PAA films were incubated in acidic, neutral and basic vapors separately. To study the morphologies after incubation, the films were stained by pH-sensitive fluorescent dyes using chemical and physical ways, and investigated with confocal laser scanning microscope (CLSM). The chemical way (labeling) was covalently linking fluoresceinamine (FAM) to some monomer units of PAA while the physical way was adsorbing rhodamine B (RB) molecules from dilute solution. Atomic force microscope (AFM) was combined with CLSM to find that after incubation in neutral or basic vapor the hydrogen-bonded PVPON/PAA films form porous structure and the pores are through the whole film.     

Hydrogen‐bonding,crystallinity, and morphological properties of poly(silicic acid)/waterborne polyurethane nanocomposites

Unique nanocomposites consisting of poly(silicic acid) nanoparticles (PNs) and waterborne polyurethane (WPU) were prepared. The aliphatic WPU prepared in this study was end‐capped with a silanol group, which could react with PNs via a sol–gel process. PNs were modified with phenyltrimethoxysilane (PTMS) and 3‐(trimethoxysilyl)propyl ester (TMPE) and then blended with WPU. The structure–property relationships were examined. Solid‐state ²⁹Si NMR spectra of WPU showed that structures T₁, T₂, and T₃ of WPU decreased and structures Q₃ and Q₄ of PN/WPU nanocomposites increased gradually. When the PN concentration increased to 10 wt %, PN/WPU nanocomposites exhibited the maximum fraction of hydrogen‐bonded carbonyl groups. In the PTMS–PN and TMPE–PN systems, the fraction of hydrogen‐bonded carbonyl groups fluctuated stably when the concentrations of PTMS–PN and TMPS–PN exceeded 5 wt %. The X‐ray diffraction results revealed that α‐form, γ‐form, or triclinic crystallization could be found in the WPU matrix. A differential scanning calorimetry spectrum showed that the crystalline structure of the hard segment of WPU was influenced by the nanoparticle concentration. The degrees of crystallinity were 88% for the PN/WPU nanocomposites, 41% for the PTMS–PN/WPU nanocomposites, and 54% for the TMPE–PN/WPU nanocomposites when the PN, PTMS–PN, and TMPE–PN concentrations were 5 wt %. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1076–1089, 2005     

Morphological characteristics of the lyotropic and gel phases in the cellulose/NH3/NH4SCN system

Solutions of cellulose in the ammonia/ammonium thiocyanate (24.5/75.5 w/w) solvent form several stable phases. Of particular interest in this work are the temperature-dependent liquid crystalline and gel phases which are stable at cellulose concentrations above 6% w/v. While the temperature-composition conditions yielding these phases are reasonably well established, very little is currently known about the morphological characteristics of lyotropic and gelled cellulose. Polarized light microscopy is employed here to demonstrate that solutions at temperatures above the gel melting point are birefringent, composed of liquid crystals. Field-emission scanning electron microscopy has been used to (i) examine the three-dimensional network in cellulose gels, and (ii) correlate network morphology with cellulose molecular weight and solution concentration. Results obtained from two complementary sample preparation techniques (i.e., critical point drying and freeze drying) are compared to identify and minimize artifacts, and reveal that gel formation occurs as the solutions phase-separate into polymer-rich anisotropic and solvent-rich isotropic phases. The polymer-rich phase is highly interconnected and forms a fibrillar network, with fibrils measuring 20–70 nm in diameter. © 1996 John Wiley & Sons, Inc.     

Synthesis of block copolymers based on poly(2,3-epithiopropylmethacrylate) via RAFT polymerization and preliminary investigations on thin film formation

New block copolymers with narrow molecular weight distribution based on (2,3-epithiopropylmethacrylate) (ETMA), methylmethacrylate (MMA) and n-butylmethacrylate (nBMA) have been successfully synthesized via reversible addition-fragmentation transfer (RAFT) polymerization. First, RAFT homopolymerization of ETMA and MMA was carried out using 2-(2-cyanopropyl) dithiobenzoate (CPDB) as the chain transfer agent (CTA) and 2,2-azobisisobutyronitrile (AIBN) as the initiator. PETMA-b-P(nBMA) copolymers were synthesized using PETMA homopolymers as the macro-chain transfer agent (MCTA), while PMMA-b-PETMA diblock copolymers were synthesized using PMMA as the MCTA. The evolution of the molecular weight and molecular weight distribution of the homo- and co-polymers were compatible with the RAFT polymerization features. Thin films from the block copolymers were prepared by spin coating a 1 wt% polymer solution from toluene, chloroform or THF. After the preparation, the films were annealed under 80% vapor pressure of chloroform for 1, 2 and 4 h and investigated with scanning electron microscopy (SEM). The most interesting results were found in the films prepared using PETMA-b-P(nBMA) copolymers (). The observed images suggested the formation of hybrid lamellar structures, ascribed to the combination of its higher molecular weight and solvents viscosity.     

Semi-interpenetrating polymer networks of polyurethane and poly(vinyl chloride)

Summary A series of semi-interpenetrating polymer networks (semi-IPN) of polyurethane (PU) and poly(vinyl chloride) (PVC) has been obtained by prepolymer method and characterised by FTIR; morphological features were examined by SEM-EDS. It has been found that PVC spherical aggregates are dispersed in the PU matrix, but Cl atoms location indicates partial miscibility of both polymers at the interphase which is probably due to hydrogen bonding and/or dipole-dipole interactions. The PVC component influences the phase behaviour of PUs hard segments, as evidenced by DSC results. Thermogravimetric analysis (TG) reveals a complex, multi-step decomposition process with the main mass loss at 503-693 K, while the DTG maxima are located between 540 and 602 K.     

Structure and properties of cellulose/poly(N‐isopropylacrylamide) hydrogels prepared by IPN strategy

Interpenetrating polymer network (IPN) strategy was developed to fabricate novel hydrogels composed of cellulose and poly(N‐isopropylacrylamide) (PNIPAAm) with high mechanical strength and adjustable thermosensitivity. Cellulose hydrogels were prepared by chemically cross‐linking cellulose in NaOH/urea aqueous solution, which were employed as the first network. The second network was subsequently obtained by in situ polymerization/cross‐linking of N‐isopropylacrylamide in the cellulose hydrogels. The results from FTIR and solid ¹³C NMR indicated that the two networks co‐existed in the IPN hydrogels, which exhibited uniform porous structure, as a result of good compatibility. The mechanical and swelling properties of IPN hydrogels were strongly dependent on the weight ratio of two networks. Their temperature‐sensitive behaviors and deswelling kinetics were also discussed. This work created double network hydrogels, which combined the advantages of natural polymer and synthesized PNIPAAm collectively in one system, leading to the controllable temperature response and improvement in the physical properties. Copyright © 2009 John Wiley & Sons, Ltd.     

Physical properties and structure of a poly(styrene-co-butadiene) rubber/poly(acrylonitrile-co-butadiene) rubber latex mixture film

The physical properties and the structure of a poly(styrene-co-butadiene) rubber (SBR) and poly(acrylonitrile-co-butadiene) rubber (NBR) latex mixture film are studied in relation to the composition of SBR/NBR for optimization as the precursor of a polymer electrolyte. The composition of SBR50/NBR50 is most suitable in terms of mechanical strength and ionic conductivity. The relationship between the mechanical strength and the structure is analyzed using a simple equivalent mechanical model modified from the Takayanagi model. Our model gives better agreement with experimental results and extends the range of validity of the model to the cocontinuous phase type morphologies. It is possible to estimate the mechanical strength from the continuity of the mechanical supporting phase, calculated from the mechanical model. The tensile properties are found to be strongly affected by the fragile component. © 1998 John Wiley & Sons, Inc. J. Polym. Sci. A Polym. Chem. 36: 2493–2501, 1998     

Effect of the diisocyanate on the structure and properties of polyurethane acrylate prepolymers

In this study, we investigated the role of diisocyanate on the properties of polyurethane acrylate (PUA) prepolymers based on polypropylene oxide (M̄_n = 2000 g · mol⁻¹). The diisocyanates studied were isophorone diisocyanate, 4‐4′dicyclohexylmethane diisocyanate, and toluene diisocyanate (pure 2,4‐TDI, pure 2,6‐TDI, and a TDI mixture, TDI_tech). The molecular structure of the diisocyanate had a major role on the course of the polycondensation and, more precisely, on the sequence length distribution of the final prepolymer. Moreover, the structural organization of the prepolymer also strongly depended on the nature of the diisocyanate. Two types of behaviors were particularly emphasized. On the one hand, the PUA synthesized from 2,4‐TDI displayed an enhanced intermixing between soft polyether segments and hard urethane groups, as revealed by the analysis of hydrogen bonding in Fourier transform infrared. Consecutively, the glass transition shifted to higher temperatures for these polymers. On the other hand, strong hard–hard inter‐urethane associations were observed in 2,6‐TDI‐based prepolymers; these led to microphase segregation between polyether chains and urethane groups, as revealed by optical microscopy. This inhomogeneous structure was thought to be responsible for the unusual rheological behavior of these PUA prepolymers. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2750–2768, 2000