Preparation and thermal properties of asymmetrically substituted poly(silylenemethylene)s

Poly(silylenemethylene)s of the types [SiMeRCH₂]_n and [SiHRCH₂]_n were prepared by the ring-opening polymerization (ROP) of 1,3-disilacyclobutanes (DSCBs) containing n-alkyl substituents, such as C₂H₅, n-C₃H₇, n-C₄H₉, n-C₅H₁₁, and n-C₆H₁₃, or a phenyl group on the Si. These new polymers include a monosilicon analog of poly(styrene), [SiHPhCH₂]_n. Improved synthesis routes to the DSCB monomers were developed which proceed through Grignard ring closure reactions on alkoxy-substituted chlorocarbosilanes. All of these asymmetrically substituted polymers were obtained in high molecular weight form, except for [SiHPhCH₂]_n. The configurations of all of the polymers were found to be atactic. The aryl-substituted polymers have higher glass transition temperatures (T_gs) and thermal stability than those of the alkyl-substituted poly(silylenemethylene)s. Unlike the polyolefins of the type [C(H)(R)CH₂]_n, where T_g drops continuously from R = Me to n-Hex, the T_gs of the n-C_nH_2n+1 (n = 2–6)-substituted [SiMeRCH₂]_n PSM's appear to reach a maximum (at −61°C) for the R = n-Pr-substituted polymer. Moreover, where it was possible to make direct comparisons among similarly substituted atactic polymers, all of the poly(silylenemethylene)s were found to have lower T_gs than their all-carbon analogs. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 3193–3205, 1997     

Molecular motion in nanocomposites of poly(ethylene oxide) and montmorillonite

Motion of chains of poly(ethylene oxide) within the interlayer spacing of 2:1 phyllosilicate/montmorillonite was studied with ¹H and ¹³C NMR spectroscopy. Measurements of the ¹H NMR line widths and relaxation times across a large temperature range were used to determine the effect of bulk thermal transitions on polymer chain motion within the nanocomposites. The results were consistent with previous reports of low apparent activation energies of motion. Details of the frequency and geometry of motion were obtained from a comparison of the ¹³C cross‐polarity/magic‐angle spinning spectra and relaxation times of the nanocomposite with those of the pure polymer. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1678–1685, 2001     

Structure and compatibility of poly(vinyl alcohol)-silk fibroin (PVA/SA) blend films

The structure and compatibility of poly(vinyl alcohol)-silk fibroin (PVA/SF) blend films were analyzed by differential scanning calorimetry (DSC), thermomechanical (TMA) and thermogravimetric (TGA) analysis, x-ray diffractometry, and scanning (SEM) and transmission (TEM) electron microscopy. DSC curves of PVA/SF blend films showed a major endothermic peak at 220°C, along with a peak at 280°C. These endotherms were assigned to the thermal decomposition of the ordered PVA elements and to the thermal degradation of silk fibroin, respectively. The PVA/SF blends behaved in a manner intermediate to the pure components, as suggested by both contraction expansion and sample weight retention properties recorded by TMA and TGA measurements. The IR absorption spectra of the blends were identified as purely a composite of the absorption bands characteristic of both PVA and SF pure polymers. The X-ray diffraction patterns of PVA/SF blends showed overlapping spacing due to PVA and SF. A dispersed phase formed by spherical particles of 3–7 μm diameter was observed by SEM and TEM. All these findings suggest that PVA and SF are incompatible. © 1994 John Wiley & Sons, Inc.     

Fully biodegradable blends of poly(butylene succinate) and poly(butylene carbonate): Miscibility, thermal properties, crystallization behavior and mechanical properties

Fully biodegradable poly(butylene succinate) (PBS) and poly(butylene carbonate) (PBC) blends were prepared by melt blending. Miscibility, thermal properties, crystallization behavior and mechanical properties of PBS/PBC blends were investigated by scanning electron microscopy (SEM), phase contrast optical microscopy (PCOM), differential scanning calorimetry (DSC), wide angle X-ray diffraction (WAXD) and mechanical properties tests. The SEM and PCOM results indicated that PBS was immiscible with PBC. The WAXD results showed that the crystal structures of both PBS and PBC were not changed by blending and the two components crystallized separately in the blends. The isothermal crystallization data showed that the crystallization rate of PBS increased with the increase of PBC content in the blends. The impact strength of PBS was improved significantly by blending with PBC. When the PBC content was 40%, the impact strength of PBS was increased by nearly 9 times.     

Surface Structure and Stereocomplex Formation of Enantiomeric Polylactide Blends Using Poly(dimethyl siloxane) as a Probe Polymer

In the stereocomplex between enantiomeric poly(l-lactide) (l-PLA) and poly(d-lactide), crystallites formed as a result of stereocomplexation, equimolar l- and d-lactide unit sequences are packed side by side. The stereocomplex exhibits a melting temperature higher by about 50 °C than that of each homopolymer. In this study, we attempt to obtain further insight into the stereocomplex-induced surface structure of enantiomeric PLA blend films. The design of the blend systems is based on principles of surface segregation of multicomponent polymeric systems with a low surface energy, triblock copolymer (l-PLA-b-PDMS-b-l-PLA) of l-PLA and poly-(dimethyl siloxane). (l-PLA-b-PDMS-b-l-PLA/l-PLA) blend films showed the surface segregation of PDMS, regardless of blend composition while the surface composition of PDMS in the (l-PLA-b-PDMS-b-l-PLA/d-PLA) blend films was strongly depended on blend composition or a degree of complexation. These results are likely due to strong interaction between d- and l-lactide unit sequences, which prevents the surface segregation of PDMS.     

弹性体偶联剂结构对PVC/PPC性能的影响

NBR－PPC弹性体偶联剂能促进PPC（聚丙撑碳酸酯）与PVC（聚氯乙烯）之间的相容性，改善共混物的力学性能，并在共混体系中产生轻度交联。偶联剂组成在NBR／PPC比例为70／30，NBR（丁腈橡胶）含腈量为34％，BPO过氧化苯甲酸用量为2．5份时，共混物的综合力学性能最佳，但偶联剂预先硫化时间不宜过长．     

Miscibility and properties of poly(l-lactic acid)/poly(butylene terephthalate) blends

Binary blends of poly(l-lactide) (PLLA) and poly(butylene terephthalate) (PBT) containing PLLA as major component were prepared by melt mixing. The two polymers are immiscible, but display compatibility, probably due to the establishment of interactions between the functional groups of the two polyesters upon melt mixing. Electron microscopy analysis revealed that in the blends containing up to 20% of poly(butylene terephthalate), PBT particles are finely dispersed within the PLLA matrix, with a good adhesion between the phases. The PLLA/PBT 60/40 blend presents a co-continuous multi-level morphology, where PLLA domains, containing dispersed PBT units, are embedded in a PBT matrix. The varied morphology affects the mechanical properties of the material, as the 60/40 blend displays a largely enhanced resistance to elongation, compared to the blends with lower PBT content.     

Water resistance, mechanical properties and biodegradability of methylated-cornstarch/poly(vinyl alcohol) blend film

The main shortcomings of biodegradable starch/poly(vinyl alcohol) (PVA) film are hydrophilicity and poor mechanical properties. With an aim to overcome these disadvantages, cornstarch was methylated and blend films were prepared by mixing methylated-cornstarch (MCS) with PVA. The mechanical properties, water resistance and biodegradability of the MCS/PVA film were investigated. It was found that MCS/PVA film had higher water resistance than the native starch/PVA film. However, the water resistance of MCS/PVA films did not have significant difference with the increase in the degree of substitution (DS) of the methylated starch from 0.096 to 0.864. Enzymatic, microbiological and soil burial biodegradation results indicated that the biodegradability of the MCS/PVA film strongly depended on the starch proportion in the film matrix. The degradation rate of starch in the starch/PVA film was hindered by blending starch with PVA. Both tensile strength and percent elongation at break of the MCS/PVA film were improved as DS of the methylated starch increased. Conversely, increasing the methylated starch proportion in film matrix deteriorated both tensile strength and percent elongation at break of the film.     

Thermal and mechanical properties of mandelic acid‐copolymerized poly(butylene succinate) and poly(ethylene adipate)

Phenyl side chains were introduced to poly(butylene succinate) and poly(ethylene adipate) by the polymerization of the respective monomers in the presence of mandelic acid. The increasing content of the phenyl side chains decreased the melting temperature and the crystallinity but increased the glass‐transition temperature of the aliphatic polyesters. The phenyl side branches reduced the crystallinity of poly(butylene succinate) more significantly than the ethyl or n‐octyl side branches did. The tensile strength, elongation, and tear strength of poly(ethylene adipate) decreased with an increase in the content of mandelic acid units. However, the increasing content of mandelic acid units enhanced the elongation and tear strength of poly(butylene succinate) considerably without a notable deterioration of tensile strength. The biodegradability of the copolyesters was increased as a result of the introduction of more mandelic acid units due to the decrease in the crystallinity. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1504–1511, 2000     

Mechanical and thermal properties of polypeptide modified hydroxyapatite/poly(L-lactide) nanocomposites

A new type of polypeptide(poly(-benzyl-L-glutamate)(PBLG))modified hydroxyapatite(HA)/poly(L-lactide)(PLLA)nanocomposites(PBLG-g-HA/PLLA)were prepared by the solvent-mixing method,and their mechanical and thermal properties were investigated.The tensile test showed that the mechanical properties of PBLG-g-HA/PLLA nanocomposites were better than that of PLLA,even a 0.3 wt%content of PBLG-g-HA in the nanocomposites could make the tensile strength 12%higher than that of the neat PLLA sample,and the tensile mod...     

Compatibilization of polypropylene/poly(glycolic acid) blend with maleated poe/attapulgite hybrid compatibilizer: Evaluation of mechanical,thermal, rheological,and morphological characteristics

In this work, the compatibilization effects of hybrid maleated POE/attapulgite hybrid compatibilizer (M-POE/ATP) on the immiscible polypropylene/poly(glycolic acid) (PP/PGA) blends was investigated. The hybrid compatibilizer integrating strengthening, toughening and compatibilization functions was prepared via one-step reactive extrusion using peroxidated ATP as the initiator. Then, the effects of compatibilizer dosage on the mechanical, thermal, rheological and morphological characteristics of blends were evaluated in detail. It was found that the hybrid compatibilizer resulted in the significantly enhanced compatibility and mechanical performance. Increased amount of compatibilizer content fractionated and almost wholly suppressed the crystallization process of PGA. The compatibilized blends showed higher thermal stability than pure PGA, and lower storage modulus and complex viscosity at higher shearing frequency. PGA in the blends presented a much lower degradation rate, which lead to the higher strength retention of 81% for the blend with 4 wt% of compatibilizer in buffer solution after 35 days.     

Compatibility and thermal properties of poly(3‐hydroxybutyrate)/poly(glycidyl methacrylate) blends

Poly(3‐hydroxybutyrate) (PHB)/poly(glycidyl methacrylate) (PGMA) blends were prepared by a solution‐precipitation procedure. The compatibility and thermal decomposition behavior of the PHB/PGMA blends was studied with differential scanning calorimetry, thermogravimetric analysis, and differential thermal analysis (DTA). The blends were immiscible in the as‐blended state, but for the blends with PGMA contents of 50 wt % or more, the compatibility was dramatically changed after 1 min of annealing at 200 °C. In addition, PHB/PGMA blends showed higher thermal stability, as measured by maximum decomposition temperatures and residual weight during thermal degradation. This was probably due to crosslinking reactions of the epoxide groups in the PGMA component with the carboxyl chain ends of PHB fragments during the degradation process, and the occurrence of such reactions can be assigned to the exothermic peaks in the DTA thermograms. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 351–358, 2002     

Structures and thermal properties of chitosan-modified poly(methyl methacrylate)

The emulsion polymerization of methyl methacrylate in the presence of chitosan with potassium persulfate (KPS) as an initiator was examined in a previous article. The free radicals that dissociated from KPS not only initiated the polymerization but also degraded the chitosan molecules. Therefore, in addition to its role as a cationic surfactant, chitosan also participated in the polymerization reaction. When the polymerization was complete, the latex polymer consisted of poly(methyl methacrylate) (PMMA) homopolymer and chitosan–PMMA copolymer. In this article, the structures and thermal properties of latex polymers are examined. Gel permeation chromatography was used to measure the molecular weight of the PMMA homopolymer, with the copolymer composition determined by an elemental analyzer. Scanning and transmission electronic microscopes were used to measure the size of latex particles from different reaction systems. The surface charges of latex particles at several different pH values were determined by the measurement of the ζ potential. All results agreed with the reaction mechanism proposed in the previous article. Finally, the presence of rigid chitosan increased the glass-transition temperature of the final latex polymers. Thermogravimetric analysis showed that the degradation behavior of latex polymers was similar to the unzipping mechanism of PMMA, yet the presence of chitosan units hindered the unzipping of the main chains in chitosan–PMMA copolymers. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 1646–1655, 2001     

Effects of organoclays on morphology and thermal and rheological properties of polystyrene and poly(methyl methacrylate) blends

Morphology, thermal and rheological properties of polymer‐organoclay composites prepared by melt‐blending of polystyrene (PS), poly(methyl methacrylate) (PMMA), and PS/PMMA blends with Cloisite® organoclays were examined by transmission electron microscopy, small‐angle X‐ray scattering, secondary ion mass spectroscopy, differential scanning calorimetry, and rheological techniques. Organoclay particles were finely dispersed and predominantly delaminated in PMMA‐clay composites, whereas organoclays formed micrometer‐sized aggregates in PS‐clay composites. In PS/PMMA blends, the majority of clay particles was concentrated in the PMMA phase and in the interfacial region between PS and PMMA. Although incompatible PS/PMMA blends remained phase‐separated after being melt‐blended with organoclays, the addition of organoclays resulted in a drastic reduction in the average microdomain sizes (from 1–1.5 μm to ca. 300–500 nm), indicating that organoclays partially compatibilized the immiscible PS/PMMA blends. The effect of surfactant (di‐methyl di‐octadecyl‐ammonia chloride), used in the preparation of organoclays, on the PS/PMMA miscibility was also investigated. The free surfactant was more compatible with PMMA than with PS; the surfactant was concentrated in PMMA and in the interfacial region of the blends. The microdomain size reduction resulting from the addition of organoclays was definitely more significant than that caused by adding the same amount of free surfactant without clay. The effect of organoclays on the rheological properties was insignificant in all tested systems, suggesting weak interactions between the clay particles and the polymer matrix. In the PS system, PMMA, and organoclay the extent of clay exfoliation and the resultant properties are controlled by the compatibility between the polymer matrix and the surfactant rather than by interactions between the polymer and the clay surface. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 44–54, 2003     

Structure and pH‐sensitive properties of poly (vinylidene fluoride) membrane changed by blending poly (acrylic acid) microgels

pH‐sensitive poly (vinylidene fluoride) (PVDF)/poly (acrylic acid) (PAA) microgels membranes are prepared by phase inversion of the N, N‐dimethylformamide solution containing PAA microgels and PVDF in aqueous solution. The composition and structure of the blend membrane are investigated by Fourier transform infrared spectra, X‐ray photoelectron spectroscopy measurements, thermo gravimetric analysis, field‐emission scanning electron microscope and atomic force microscope. The results indicate the surface and cross section of the blend membranes have a porous structure with PAA microgels immobilized inside the pore and on the membrane surface. The blend PVDF membranes exhibit pH‐sensitive water flux, with the most drastic change in permeability observed between pH 3.7 and 6.3. The blend membranes are fouled by bovine serum albumin, and their antifouling property is enhanced by increasing PAA microgels, mainly derived from the improved hydrophilic property. Copyright © 2013 John Wiley & Sons, Ltd.     

Effect of poly(vinyl acetate) (PVAc) on thermal behavior and mechanical properties of poly(3-hydroxybutyrate)/poly(propylene carbonate) (PHB/PPC) blends

To assess the compatibility of blends of synthetic poly(propylene carbonate) (PPC), with a natural bacterial poly(3-hydroxybutyrate) (PHB), a simple casting procedure of blend was used. poly(3-hydroxybutyrate)/poly(propylene carbonate) blends are found to be incompatible according to DSC and DMA analysis. In order to improve the compatibility and mechanical properties of PHB/PPC blends, poly(vinyl acetate) (PVAc) was added as a compatibilizer. The effects of PVAc on the thermal behavior, morphology, and mechanical properties of 70PHB/30PPC blend were investigated. The results show that the melting point and the crystallization temperature of PHB in blends decrease with the increase of PVAc content in blends, the loss factor changes from two separate peaks of 70PHB/30PPC blend to one peak of 70PHB/30PPC/12PVAc blend. It is also found that adding PVAc into 70PHB/30PPC blend can decrease the size of dispersed phase from morphology analysis. The result of tensile properties shows that PVAc can increase the tensile strength and Young’s modulus of 70PHB/30PPC blend, and both the elongation at break and the tensile toughness increase significantly with PVAc added into 70PHB/30PPC.     

Improvement of compatibility,mechanical, thermal and dielectric properties of poly(lactic acid) and poly(butylene adipate-co-terephthalate) blends and their composites with porous clay heterostructures from mixed surfactant systems

In this study, nanocomposite poly(lactic acid) and poly(butylene adipate-co-terephthalate) (PLA/PBAT) blends were prepared through polymer blending in the presence of multi-functional epoxy as a compatibilizer that could react with epoxy group and terminated end group of two phases to increase interfacial adhesion between PLA and PBAT and improve the toughness of PLA. The effects of porous clay heterostructure from mixed CTAB:CTAC surfactant in the mole ratio of 1:2 (B1C2-PCH) were also investigated. The elongation at break of the blends reached 38%, which was eight times that of neat PLA. The cryo-fractured surface demonstrated the interfacial adhesion caused by the interaction of the epoxy group of the reactive compatibilizer with the terminal carboxyl and hydroxyl groups of PLA and PBAT. Moreover, PBAT reduced the crystallization rate and percent crystallinity of the PLA matrix and further decreased when compatibilizer was used. Alternatively, B1C2-PCH accelerated the heterogeneous nucleation and crystallization of the nanocomposite films. After adding small amount of B1C2-PCH, the nanocomposite films demonstrated excellent dielectric properties. Therefore, the improvement of PLA/PBAT nanocomposite blends are capable to be further developed as polymeric capacitor films.     

Structure and mechanical properties of poly(L‐lactic acid) crystals and fibers

The elastic constants of poly(L ‐lactic acid) (PLLA) crystals are reported on the basis of a commercial software package and the published crystal structure of the α form. A chain modulus of 36 GPa and a shear modulus of 3 GPa have been obtained for cylindrically symmetric aggregates of perfectly oriented crystals. The helical conformation of the PLLA molecule reduces the stiffness in the chain axis direction because bond rotation plays a significant role in the deformation. X‐ray crystal strain measurements suggest that shear of the α crystal parallel to the helix axis is the easiest mode of deformation, in agreement with the expectations obtained from the low shear modulus of 3 GPa obtained from the theoretical calculations. A combination of small‐ and wide‐angle X‐ray scattering, differential scanning calorimetry, dynamic mechanical thermal analysis, and shrinkage measurements has been used to characterize the structure that develops and the crystal transformation that occurs during fiber processing. The structure that develops during processing very much depends on the crystal transformation, and a structural model is proposed for fibers at different degrees of plastic deformation. The transformation of the α crystal into the β form and vice versa is governed primarily by shear along the helix axis because the chains must shear past each other during the crystal transformation, disrupting the lamellar packing. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 892–902, 2007