Synthesis and properties of polyimide–clay hybrid

A polyimide hybrid with montmorillonite clay mineral has been synthesized from a dimethylacetamide (DMAC) solution of poly(amic acid) and a DMAC dispersion of montmorillonite intercalated with an ammonium salt of dodecylamine. Montmorillonite consists of stacked silicate sheets about 2000 Å in length, 10 Å in thickness. In this hybrid, montmorillonite is dispersed homogeneously into the polyimide matrix and oriented parallel to the film surface. Thanks to this special structure, this hybrid showed excellent gas barrier properties. Only 2 wt % addition of montmorillonite brought permeability coefficients of various gases to values less than half of those of ordinary polyimide. Furthermore, this hybrid had low thermal expansion coefficient. © 1993 John Wiley & Sons, Inc.     

Structural characteristics and moisture sorption behavior of nylon‐6/clay hybrid films

The structure of nylon‐6 hybrids with synthetic or natural clays was investigated for melt‐pressed films with Fourier transform infrared spectroscopy, wide‐angle X‐ray diffraction, and differential scanning calorimetry in comparison with the nylon‐6 homopolymer. In contrast to the development of familiar α‐form crystals in plain nylon‐6 film, the hybrid films produced γ‐form crystals when nylon‐6 was conjugated with synthetic mica, whereas the hybridization with natural montmorillonite gave rise to both α‐ and γ‐crystalline modifications. The degree of crystallinity of the nylon‐6 hybrid with synthetic mica was the highest of the three series. Moisture sorption isotherms obtained for these nylon‐6‐based films were all typically sigmoid‐shaped, although the prevalence of a higher crystallinity in the hybrid samples lowered the degree of moisture regain. The sorption behavior was analyzed well in terms of the parameters of a Brunauer–Emmett–Teller multiplayer adsorption model and a Flory–Huggins treatment. It was also observed that the cluster formation of the water adsorbed into the nylon‐6 matrix tended to be restricted by the hybridization with clay. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 479–487, 2002; DOI 10.1002/polb.10106     

Synthesis and characterization of organosoluble,thermoplastic elastomer/clay nanocomposites

We synthesized organosoluble, thermoplastic elastomer/clay nanocomposites by making a jelly like solution of ethylene vinyl acetate containing 28% vinyl acetate (EVA‐28) and blending it with organomodified montmorillonite. Sodium montmorillonite (Na⁺‐MMT) was made organophilic by the intercalation of dodecyl ammonium ions. X‐ray diffraction patterns of Na⁺‐MMT and its corresponding organomodified dodecyl ammonium ion intercalated montmorillonite (12Me‐MMT) showed an increase in the interlayer spacing from 11.94 to 15.78 Å. However, X‐ray diffraction patterns of the thermoplastic elastomer and its hybrids with organomodified clay contents up to 6 wt % exhibited the disappearance of basal reflection peaks within an angle range of 3–10°, supporting the formation of a delaminated configuration. A hybrid containing 8 wt % 12Me‐MMT revealed a small hump within an angle range of 5–6° because of the aggregation of silicate layers in the EVA‐28 matrix. A transmission electron microscopy image of the same hybrid showed 3–5‐nm 12Me‐MMT particles dispersed in the thermoplastic elastomer matrix; that is, it led to the formation of nanocomposites or molecular‐level composites with a delaminated configuration. The formation of nanocomposites was reflected through the unexpected improvement of thermal and mechanical properties; for example, the tensile strength of a nanocomposite containing only 4 wt % organophilic clay was doubled in comparison with that of pure EVA‐28, and the thermal stability of the same nanocomposite was higher by about 34 °C. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2065–2072, 2002     

Poly(lactic acid) nanocomposites with various organoclays. I. Thermomechanical properties,morphology, and gas permeability

The thermomechanical properties, morphology, and gas permeability of hybrids prepared with three types of organoclays were compared in detail. Hexadecylamine–montmorillonite (C₁₆–MMT), dodecyltrimethyl ammonium bromide–montmorillonite (DTA‐MMT), and Cloisite 25A were used as organoclays in the preparation of nanocomposites. From morphological studies using transmission electron microscopy, most clay layers were found to be dispersed homogeneously in the matrix polymer, although some clusters or agglomerated particles were also detected. The initial degradation temperature (at a 2% weight loss) of the poly(lactic acid) (PLA) hybrid films with C₁₆–MMT and Cloisite 25A decreased linearly with an increasing amount of organoclay. For hybrid films, the tensile properties initially increased but then decreased with the introduction of more of the inorganic phase. The O₂ permeability values for all the hybrids for clay loadings up to 10 wt % were less than half the corresponding values for pure PLA, regardless of the organoclay. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 94–103, 2003     

层柱人工水热合成皂石的制备与表征(英)

利用具有理想皂石结构的人工水热合成蒙皂石为层原料，通过与羟基聚合铝离子（[Al₁₃O₄(OH)₂₄(H₂O)₁₂]⁷⁺）交换反应合成得到了一种层柱粘土。实验对于该铝柱皂石进行了粉末XRD，FT-IR和TG-DTA表征。氮气吸附实验说明其高温活化（773K，2 h）产物具有很高的BET比表面（360 m²·g^-1）。相对于层柱蒙脱土，层柱皂石显示了更高的催化裂解性能和热稳定性。层柱皂石的异丙苯裂解转化率达到了65%；而层柱蒙脱土的转化率只有4%。这说明层材料的四面体取代对于层柱粘土Br?nsted酸位的形成具有重要的决定作用。氨程序升温脱附实验发现铝柱皂石在350～650 ℃区间具有较强的氨脱附量，表明层柱皂石具有层柱蒙脱土所没有的强酸中心。     

One-pot synthesis of nylon 6–clay hybrid

Nylon 6–clay hybrid is a molecular composite of nylon 6 and uniformly dispersed silicate layers of montmorillonite. One-pot synthesis of the hybrid was carried out by the following procedures. Montmorillonite was dispersed in water, and then ε-caprolactam, acid (phosphoric acid, hydrochloric acid, benzenesulfonic acid, isophthalic acid, trichloroacetic acid, or acetic acid), and 6-aminocaproic acid were added to the dispersion. The mixtures were reacted at 260°C for 6 h, yielding the nylon 6–clay hybrids (1potNCHs). X-ray diffraction revealed that the silicate layers of 1potNCH by phosphoric acid were uniformly dispersed in the nylon 6 matrix. The 1potNCH had excellent mechanical properties. The strength and the modulus of the hybrid increased compared with previously reported nylon 6–clay hybrid (NCH) synthesized by montmorillonite intercalated with 12-aminolauric acid. The heat distortion temperature (HDT) of the 1potNCH was 160°C, which was 8°C higher than that of NCH. In other 1potNCHs, montmorillonite had a smaller effect on the increase of those properties, and interlayer spacing of montmorillonite was observed at ca. 20 Å. © 1993 John Wiley & Sons, Inc.     

Nanocomposites of polyurethane with various organoclays: Thermomechanical properties,morphology, and gas permeability*

The properties of polyurethane (PU) nanocomposites with three different organoclays were compared in terms of their thermal stabilities, mechanical properties, morphologies, and gas permeabilities. Hexadecylamine–montmorillonite, dodecyltrimethyl ammonium–montmorillonite, and Cloisite 25A were used as organoclays for making PU hybrid films. The properties were examined as a function of the organoclay content in a matrix polymer. Transmission electron microscopy photographs showed that most clay layers were dispersed homogeneously into the matrix polymer on the nanoscale, although some particles of clay were agglomerated. Moreover, the addition of only a small amount of organoclay was enough to improve the thermal stabilities and mechanical properties of PU hybrid films, whereas gas permeability was reduced. Even polymers with low organoclay contents (3–4 wt %) showed much higher strength and modulus values than pure PU. Gas permeability was reduced linearly with an increasing amount of organoclay in the PU matrix. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 670–677, 2002; DOI 10.1002/polb.10124     

Nanocomposites of NLO chromophore‐modified layered silicates and polypropylene

Intercalation of guest species into layered inorganic solids is a method of producing ordered inorganic–organic assemblies with unique microstructures controlled by host–guest and guest–guest interactions. Smectite clay minerals, such as montmorillonite, having appropriate functional molecules in between the silicate layers are supposed to exhibit a wide range of novel characteristics. Nanocomposite material based on maleic anhydride‐grafted polypropylene and dye‐modified layered silicate was developed. Characteristics of organo‐modified montmorillonite particles and polymer/clay hybrids have been investigated through FTIR, SAXS, DSC, UV measurements, and transmission electron microscopy. The results of the intercalation process, structural characterization, and thermal properties will be discussed in comparison with the intercalation and nanocomposite preparation results. The intercalation was successfully conducted by the ion‐exchange method. It was shown that intercalated dibenzilidene acetone type chromophores exist in the clay galleries in an aggregated form, probably as J‐aggregates. This feature strongly effects on optical and nonlinear optical properties of nanocomposites. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2493–2502, 2005     

Montmorillonite‐based nanocomposites of polybenzoxazole: Synthesis and characterization (I)

Poly(amic acid) was synthesized by means of low‐temperature‐solution polymerization of 3,3′‐dihydroxybenzidine and pyromellitic dianhydride in N,N‐dimethylacetamide. The precursor polymer was heat‐treated at different temperatures to create a polybenzoxazole (PBO) through a polyimide (PI). PI containing the hydroxyl group was rearranged by decarboxylation with heat treatment, resulting in a fully aromatic PBO. Hexadecylamine was used as an organophilic alkylamine in organo‐clay. We have tried to clarify the intercalation of heterocyclic polymer chains to hexadecylamine–montmorillonite (C₁₆‐MMT) and improve tensile properties. It was found that the addition of only a small amount of organo‐clay was enough to improve the mechanical properties of PBO. Maximum enhancement in the ultimate tensile strength for PBO hybrids was observed for the blends containing 4% C₁₆‐MMT. The initial modulus monotonically increased with further increases in the C₁₆‐MMT content. © 2001 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 471–476, 2001     

Synthesis and characterization of polyethylene/clay–silica nanocomposites: A montmorillonite/silica‐hybrid‐supported catalyst and in situ polymerization

A novel approach to the preparation of polyethylene (PE) nanocomposites, with montmorillonite/silica hybrid (MT‐Si) supported catalyst, was developed. MT‐Si was prepared by depositing silica nanoparticles between galleries of the MT. A common zirconocene catalyst [bis(cyclopentadienyl)zirconium dichloride/methylaluminoxane] was fixed on the MT‐Si surface by a simple method. After ethylene polymerization, two classes of nanofillers (clay layers and silica nanoparticles) were dispersed concurrently in the PE matrix and PE/clay–silica nanocomposites were obtained. Exfoliation of the clay layers and dispersion of the silica nanoparticles were examined with transmission electron microscopy. Physical properties of the nanocomposites were characterized by tensile tests, dynamic mechanical analysis, and DSC. The nanocomposites with a low nanofiller loading (<10 wt %) exhibited good mechanical properties. The nanocomposite powder produced with the supported catalyst had a granular morphology and a high bulk density, typical of a heterogeneous catalyst system. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 941–949, 2004     

Nanocomposites of poly(ethylene terephthalate‐co‐ethylene naphthalate) with organoclay

Poly(ethylene terephthalate‐co‐ethylene naphthalate) (PETN)/organoclay was synthesized with the solution intercalation method. Hexadecylamine was used as an organophilic alkylamine in organoclay. Our aim was to clarify the intercalation of PETN chains to hexadecylamine–montmorillonite (C₁₆–MMT) and to improve both the thermal stability and tensile property. We found that the addition of only a small amount of organoclay was enough to improve the thermal stabilities and mechanical properties of PETN/C₁₆–MMT hybrid films. Maximum enhancement in both the ultimate tensile strength and initial modulus for the hybrids was observed in blends containing 4 wt % C₁₆–MMT. Below a 4 wt % clay loading, the clay particles could be highly dispersed in the polymer matrix without a large agglomeration of particles. However, an agglomerated structure did form in the polymer matrix at a 6 wt % clay content. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2581–2588, 2001     

Preparation of the polymer–clay nanocomposites in exfoliated state by interface stabilization

To suppress the repulsive interfacial energy between hydrophilic clay and a hydrophobic polymer matrix for polymer–clay nanocomposites, a third component of amphiphilic nature such as poly(?‐caprolactone) (PCL) was introduced into the styrene–acrylonitrile copolymers (SAN)/Na‐montmorillonite system. Once ?‐caprolactone was polymerized in the presence of Na‐montmorillonite, the successful ring‐opening polymerization of ?‐caprolactone and the well‐developed exfoliated structure of PCL/Na‐montmorillonite mixture were confirmed. Thereafter, SAN was melt‐mixed with PCL/Na‐montmorillonite nanocomposite, and the SAN matrix and PCL fraction were completely miscible to form a homogeneous mixture with retention of the exfoliated state of Na‐montmorillonite, exhibiting that PCL effectively stabilizes the repulsive polymer–clay interface and contributes to the improvement of the mechanical properties of nanocomposites. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 246–252, 2004     

Gas barrier of polystyrene montmorillonite clay nanocomposites: Effect of mineral layer aggregation

Three polystyrene (PS)/clay hybrid systems have been prepared via in situ polymerization of styrene in the presence of unmodified sodium montmorillonite (Na‐MMT) clay, MMT modified with zwitterionic cationic surfactant octadecyldimethyl betaine (C18DMB) and MMT modified with polymerizable cationic surfactant vinylbenzyldimethyldodecylammonium chloride (VDAC). X‐ray diffraction and TEM were used to probe mineral layer organization and to expose the morphology of these systems. The PS/Na‐MMT composite was found to exhibit a conventional composite structure consisting of unintercalated micro and nanoclay particles homogeneously dispersed in the PS matrix. The PS/C18DMB‐MMT system exhibited an intercalated layered silicate nanocomposite structure consisting of intercalated tactoids dispersed in the PS matrix. Finally, the PS/VDAC‐MMT system exhibited features of both intercalated and exfoliated nanocomposites. Systematic statistical analysis of aggregate orientation, characteristic width, length, aspect ratio, and number of layers using multiple TEM micrographs enabled the development of representative morphological models for each of the nanocomposite structures. Oxygen barrier properties of all three PS/clay hybrid systems were measured as a function of mineral composition and analyzed in terms of traditional Nielsen and Cussler approaches. A modification of the Nielsen model has been proposed, which considers the effect of layer aggregation (layer stacking) on gas barrier. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1733–1753, 2007     

Confinement and controlled release of quinine on chitosan–montmorillonite bionanocomposites

To accomplish the controlled‐release systems based on layered clay minerals, one of the best ways is to intercalate organic molecules into the interlayer gallery of clay minerals. Into a series of chitosan (CS) intercalated montmorillonite (MMT) nanocomposites, prepared via ion‐exchange route, antimalarial drug [quinine (QUI)] was loaded to act as effective drug delivery systems. Among the CS–MMT nanocomposites, higher drug adsorption with decreasing CS concentration was observed. CS–MMT and CS–MMT/QUI intercalated compounds were characterized by powder X‐ray diffraction, Fourier transform infrared spectroscopy, and thermal analysis. The synthesized nanocomposites, filled in the gelatin capsules followed by coating of Eudragit® L 100, were tested for in vitro drug release performance in the sequential buffer environments at 37 ± 0.5 °C. As no drug release (0%) was observed in the gastric fluid, the coating of Eudragit® L 100 to the capsules is highly adequate. However, the drug release rate was comparatively faster from the CS intercalated clay with compare with pure clay. The drug release kinetic data revealed that the release of QUI from the nanocomposites can be explained by modified Freundlich model. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Novel synthesis of polyimide–polyhybridsiloxane block copolymers via polyhydrosilylation: Characterization and physical properties

The insertion of soft polysiloxane segments into a polyimide backbone introduces changes in its properties (processability, low surface tension, gas permeability, and lower dielectric constant). Generally, these polyimide–polysiloxane copolymers are synthesized by the condensation of a dianhydride with an aromatic diamine and an amine telechelic polysiloxane, or by transimidization between an aminopyridine‐terminated oligoimide and an amine end‐capped oligosiloxane. This study investigated another route to obtain perfectly alternating polyimide–polyhybridsiloxane (PI–PHSX) block copolymers. The hydrosilylation, widely studied previously, was performed to elaborate copolymers from an allyl telechelic polyimide and a hydrosilane telechelic polyhybridsiloxane. The use of a telechelic polyhybridsiloxane as a soft segment brought better thermostability and better chemical resistance in comparison with an oligosiloxane based on ? Si(CH₃)₂? O? units. Using the same allyl telechelic polyimide moiety but varying the size of the hybrid siloxane part, we obtained different PI–PHSX block copolymers, leading to thermoplastic elastomers (TPE). We investigated the effect of the soft‐segment length on the thermal resistance, activation energy of thermal degradation, mechanical behavior, and surface properties of a series three PI–PHSX block copolymers containing 36, 54, and 75 wt % polyimide. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2414–2425, 2001     

Morphology and gas barrier properties of polyethylene‐based nanocomposites

Nanocomposites were processed by melt blending two reference matrices, a metallocene polyethylene and a low density maleic anhydride‐grafted polyethylene with an organo‐modified montmorillonite. It was shown that the introduction of a maleated polyethylene compatibilizer was required to improve the clay nanoplatelet dispersion in the metallocene polyethylene‐based nanocomposites. Increasing the montmorillonite content led to a significant increase of the barrier properties. Interfacial agents such as oxidized paraffins were shown to be more effective to reduce the gas permeability than maleated polyethylene and the dependence of the gas transport properties was discussed not only as a function of the clay dispersion but also as a function of the clay/compatibilizer and compatibilizer/matrix interactions. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 431–440, 2006     

New poly(butylene succinate)/layered silicate nanocomposites. II. Effect of organically modified layered silicates on structure,properties, melt rheology,and biodegradability

A series of new poly(butylene succinate) (PBS)/layered silicate nanocomposites were prepared successfully by simple melt extrusion of PBS and organically modified layered silicates (OMLS). Three different types of OMLS were used for the preparation of nanocomposites: two functionalized ammonium salts modified montmorillonite and a phosphonium salt modified saponite. The structure of the nanocomposites in the nanometer scale was characterized with wide-angle X-ray diffraction and transmission electron microscopic observations. With three different types of layered silicates modified with three different types of surfactants, the effect of OMLS in nanocomposites was investigated by focusing on four major aspects: structural analysis, materials properties, melt rheological behavior, and biodegradability. Interestingly, all these nanocomposites exhibited concurrent improvements of material properties when compared with pure PBS. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 3160–3172, 2003     

Phase behavior of modified montmorillonite– poly(ϵ‐caprolactone) nanocomposites

The thermal behavior and overall isothermal crystallization kinetics of a series of organophilic modified montmorillonite–poly(?‐caprolactone) nanocomposites were investigated. In general, the thermal behavior was influenced more by the type of dispersion than by the clay content. For nanocomposites in which silicate platelets were predominantly dispersed in the polymer matrix to give exfoliated structures, the thermal properties were improved with respect to those of neat poly(?‐caprolactone), whereas in those cases in which simply intercalated structures were attained, the thermal properties regularly decayed as the clay content increased. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1321–1332, 2004     

Synthesis of a hexafluoropropylidene-bis(phthalic anhydride)-based polyimide and its conducting polymer composites with polypyrrole

A new electrically conducting composite film from polypyrrole and 4,4′-(hexafluoroisopropylidene)-bis(phthalic anhydride)-based polyimide was prepared. Pyrrole and the dopant ion can easily penetrate through the polyimide substrate and electropolymerize on the platinum (Pt) electrode due to the swelling of the polyimide on the metal electrode. The electrochemical properties of polypyrrole-polyimide (PPy/PI) composite films have been investigated by using cyclic voltammetry. The PPy/PI composite film is suitable for use as the electroactive material owing to its stable and controllable electrochemical properties. The electrical conductivity of composites falls in the range 0.0035–15 S/cm. Scanning electron micrograph, FTIR, and thermal studies indicate that PPy and PI form a homogeneous material rather than a simple mixture. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 3009–3016, 1997     

Preparation and properties of nanocomposites based on acrylonitrile–butadiene rubber,styrene–butadiene rubber,and polybutadiene rubber

Nanocomposites were prepared with different grades of nitrile rubber with acrylonitrile contents of 19, 34, and 50%, with styrene–butadiene rubber (23% styrene content), and with polybutadiene rubber with Na‐montmorillonite clay. The clay was modified with stearyl amine and was characterized by X‐ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, and transmission electron microscopy (TEM). The XRD studies showed an increase in the gallery gap upon the modification of the filler by stearyl amine. The intercalation of the amine chains into the clay gallery gap was confirmed by the presence of some extra peaks (2928, 2846, and 1553 cm^?1) in the FTIR spectra. The clay–rubber nanocomposites were characterized by TEM and XRD. The mechanical properties were studied for all the compositions. An improvement in the mechanical properties with the degree of filler loading up to a certain level was observed. The changes in the mechanical properties, with changes in the nature and polarity of the rubbers, were explained with the help of XRD and TEM results. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1573–1585, 2004