Synthesis and polymerization of (E)‐p‐[(p‐methoxyphenyl)‐2‐ethenyl]phenylacetylene with Ziegler–Natta,rhodium, and palladium complexes

The synthesis and polymerization of (E)‐p‐[(p‐methoxyphenyl)‐2‐ethenyl]phenylacetylene was carried out with a homogeneous vanadium acetylacetonate/aluminum triethyl catalyst system, a bis(rhodium chloride cycloocta‐1,5‐diene) complex, and a palladium/trimethylsilyl complex. In all cases, the main fraction was a polymer with a stereoregular structure. The polymerization with the vanadium catalyst gave a polymer fraction in a low yield. The polymerization of (E)‐p‐[(p‐methoxyphenyl)‐2‐ethenyl]phenylacetylene with the soluble rhodium complex gave a polymer in a high yield. The soluble palladium/chlorotrimethylsilane complex gave a polymer in a good yield. On the basis of the spectroscopic data, the poly{(E)‐p‐[(p‐methoxyphenyl)‐2‐ethenyl]phenylacetylene)} obtained, in all cases, showed a cis–transoidal stereoregular structure. The molecular mass of poly{(E)‐p‐[(p‐methoxyphenyl)‐2‐ethenyl]phenylacetylene)} was determined by the matrix‐assisted laser desorption/ionization time‐of‐flight technique. The kinetics of the reaction were analyzed. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 6438–6444, 2005     

Nanoscopic confinement effects on ethylene polymerization by intercalated silicate with metallocene catalyst

In this article we report a study of in situ polymerization of ethylene by intercalated montmorillonite (MMT) with metallocene, allowing an investigation of the nanoscopic confinement effect of olefin polymerization and of the structure of polymer prepared in situ. Ethylene polymerization by intercalated MMT with metallocene and the varied aggregation morphology of the resulting polymer during polymerization were studied by X‐ray diffraction (XRD), differential scanning calorimetry (DSC), and gel permeation chromatography (GPC). The polymerization kinetics and the resulting polymer before and after destruction of the silicate registry were different. The laminated structure of silicate lowered the all‐reaction rate, including the propagation, chain transfer, and termination reactions, producing polymer of a high molecular weight. Moreover, the melting point of the polymer gradually increased during the in situ polymerization, indicating that nanoscopic confinement between solid surfaces affects the crystallization behavior of polyethylene via in situ polymerization. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 38–43, 2004     

Ring‐opening polymerization of lipoic acid and characterization of the polymer

Thermal polymerization of DL ‐α‐lipoic acid (LPA) in bulk without any initiator proceeded easily above the melting point of LPA. The molecular weight polymer determined by GPC was high. From the ¹H NMR spectra of polymers, poly(LPA) obtained from polymerization of high purity LPA was to consist of cyclic structures, which was confirmed by ESI‐MS. Interlocked polymer consisting of poly(LPA) and dibenzo‐30‐crown‐10 entangled with each other was synthesized by the polymerization of LPA in the presence of dibenzo‐30‐crown‐10. From the DSC analysis of the polymers, glass transition temperature was estimated to be about ?11 °C, but melting point was not observed, indicating that poly(LPA) is an amorphous polymer. By photodecomposition of poly(LPA), M_n was rapidly decreased at the early stage of the decomposition. After that, the M_n of the polymer kept and then was almost constant even for a prolonged reaction time. On the basis of the results, it would be presumed that poly (LPA) obtained form polymerization of high purity LPA includes an interlocked structure. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Dual bimodal polyethylene prepared by intercalated silicate with nickel diimine complex

The ethylene polymerization was catalyzed by the intercalated montmorillonite with the nickel complex, [ArN?C(Me)? C(Me)?NAr]NiBr₂ (Ar = 2,6‐C₆H₃ (i‐Pr)₂). Polymer with low melting point and high molecular weight was produced at the early stage of polymerization followed by formation of polymer with high melting point and low molecular weight. It is proposed that the gallery of silicate lowers the propagation rate of polymerization and frequency of “chain walking” process of nickel complex anchored inside the gallery, which produces polymer with low molecular weight and low branching, whereas the nickel complex immobilized on the surface of silicate generates polymer with high molecular weight and high branching. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5506–5511, 2005     

Coupling polymerization of monofunctional allene derivatives with malonates bearing aryl halides moieties via π-allylpalladium complex

A novel polymerization method of allene derivatives with nucleophiles bearing aryl halide moieties (A-B type) is described. By the polymerization of hexylallene with malonates bearing an aryl iodide part, polymers consisting both of internal and exomethylene (exo) double bonds were obtained by mean of the coupling reaction of three different components in high yields. On the other hand, a polymer obtained from phenylallene was selectively composed of internal double bonds (E and Z). By the reaction of hexylallene with a malonate bearing two aryl halide moieties (A-B₂ type), a multibranched polymer was also obtained. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 2097–2103, 1997     

Polymer‐supported half‐titanocene catalysts for the syndiospecific polymerization of styrene

Monocyclopendienyltitanium trichloride (CpTiCl₃) was supported on polymer carriers with different hydroxyl contents, and the supported catalysts were used for styrene polymerization. The supported catalysts exhibited high activity even at low Al/Ti ratios and increased the molecular weight of the products, indicating that polymer carriers could stabilize the active sites. The polymers prepared with unsupported and supported catalysts were extracted with boiling n‐butanone and characterized by carbon nuclear magnetic resonance (¹³C NMR) and differential scanning calorimetry. The polymers obtained by supported catalysts had a high fraction of boiling n‐butanone‐insoluble part and high melting temperatures, but ¹³C NMR results showed that syndiotacticity decreased compared with that of polymers prepared with an unsupported catalyst. ESR study on the supported catalysts confirmed that the active sites supported on the carrier dropped into the solution and formed active sites the same as those in the unsupported system when they reacted with methylaluminoxane. ¹³C NMR analysis showed that the polymerization mechanism of the supported active sites was an active‐site controlled mechanism instead of a chain‐end controlled mechanism of the unsupported active sites. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 127–135, 2000     

Preparation of functional polymers by living anionic polymerization: Polymerization of allyl methacrylate

The anionic polymerization of allyl methacrylate was carried out in tetrahydrofuran, both in the presence and in the absence of LiCl, with a variety of initiators, at various temperatures. It was found that (1,1-diphenylhexyl)lithium and the living oligomers of methyl methacrylate and tert-butyl methacrylate are suitable initiators for the anionic polymerization of this monomer. The temperature should be below −30°C, even in the presence of LiCl, for the living polymerization to occur. When the polymerization proceeded at −60°C, in the presence of LiCl, with (1,1-diphenylhexyl)-lithium as initiator, the number-average molecular weight of the polymer was directly proportional to the monomer conversion and monodisperse poly(allyl methacrylate)s with high molecular weights were obtained. ¹H-NMR and FT-IR indicated that the α CC double bond of the monomer was selectively polymerized and that the allyl group remained unreacted. The prepared poly(allyl methacrylate) is a functional polymer since it contains a reactive CC double bond on each repeating unit. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 2901–2906, 1997     

Oxidative polymerization of p-alkylphenols catalyzed by horseradish peroxidase

Enzymatic oxidative polymerization of p-alkylphenols using horseradish peroxidase as catalyst has been carried out in two polymerization solvent systems: a mixture of phosphate buffer (pH 7) and 1,4-dioxane, and a reverse micellar solution, yielding powdery polymeric materials. The polymer yield was much dependent upon the type of alkyl group in the monomer as well as the solvent type. In case of the polymerization of umbranched alkylphenols in the aqueous 1,4-dioxane, the polymer yield increased with increasing chain length of the alkyl group from 1 to 5, and the yield of the polymer from hexyl or heptylphenol was almost the same as that of the pentyl derivative. The relationship between the type of substituent and the polymer yield in the reverse micellar system was different from that in the aqueous 1,4-dioxane; the highest yield was achieved from ethylphenol. The resulting polymers had molecular weight of several thousands. The polymer was estimated to be composed from a mixture of phenylene and oxyphenylene units from IR analyses. TG measurement exhibited that the polymer had relatively high thermal stability. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 1453–1459, 1997     

Thermal polycondensation of sugar fluoride to form highly branched polysaccharide

Sugar fluorides were found to undergo powder‐to‐powder polycondensation without any catalyst at 110–160 °C under vacuum, giving highly branched polysaccharides (Conv. = 40–95%, M_w = 1400–20,000). The cross‐polarized optical microscopy at 110 °C disclosed that the crystal shape of α‐glucosyl fluoride ( FGlc ) was unchanged throughout the polymerization in spite of producing the amorphous polymer ( Poly‐FGlc ). The solid‐state post polymerization of Poly‐FGlc (M_w: 2700) at 180 °C increased the higher molecular weight (M_w: 8900). The product polysaccharide was per‐O‐methylated and subjected to structure analyses. Acid‐hydrolysis, which gave a variety of the partially O‐methylated monosaccharides, suggested that the product polysaccharides had a highly branched structure consisting of all of the possible glycosidic linkages. MALDI‐TOF mass analysis revealed that the 1,6‐anhydride terminal unit was formed and participated to the polymerization. Interestingly, α‐maltosyl fluoride hydrate ( FMal·H ₂ O ) was polymerized at the lower temperature (100 °C) than the anhydrate ( FMal ), which required 160 °C for the polymerization. They produced different structure polymers even from the same monomer. The polymer from the former consisted of the disaccharide‐repeating unit, while the repeating unit of the polymer from the latter was the monosaccharide, which was formed by the acetal exchange reaction. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3851–3860, 2007     

Crystallization and thermal properties of PLLA comb polymer

Poly(L ‐lactide) (PLLA) on poly(2‐hydroxyethyl methacrylate) (PHEMA) backbone was prepared by a combination of atom transfer radical polymerization (ATRP) and ring‐opening polymerization (ROP). The structure of the comb polymer was analyzed by wide angle X‐ray diffraction (WAXD), small angle X‐ray scattering (SAXS), and differential scanning calorimetry (DSC). WAXD result indicates that the comb polymer has α crystalline modification with a 10₃ helical conformation. Lamellar parameters of the crystalline structure were obtained by one‐dimension correlation function (1DCF) calculated from SAXS results. The calculations show that the thickness of crystalline layer is controlled by annealing temperature and comb structure. DSC was applied to study kinetics of the crystallization and melting behavior. Two melting peaks on melting curves of the comb polymer at different crystallization temperature were detected, and the peak at higher temperature is attributed to the melt‐recrystallization. The equilibrium melting temperature is found to be influenced by the comb structure. In this article the effects of the comb structure on Avrami exponent, equilibrium melting point and melting peak of the comb polymer were discussed. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 589–598, 2008     

A kind of novel nonmetallocene catalysts for ethylene polymerization

A kind of novel bridged nonmetallocene catalysts was synthesized by the treatment of N,N‐imidazole and N,N‐phenylimidazole with n‐BuLi, and MCl₄ (M = Ti, Zr) in THF. Those catalysts were performed for ethylene polymerization after activated by methylaluminoxane (MAO). The effects of polymerization temperature, Al/M ratio, pressure of monomer, and concentration of catalysts on ethylene polymerization behaviors were investigated in detail. Those results revealed that the catalyst system was favorable for ethylene polymerization with high catalytic activity. The polymer was characterized by ¹³C NMR, WAXD, GPC, and DSC. The result confirmed that the obtained polyethylene featured broad molecular weight distribution around 20, linear structure, and relative low melting temperature. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 33–37, 2008     

Dispersion copolymerization of poly(oxyethylene) macromonomers and styrene

The kinetics of dispersion copolymerization of methacryloyl-terminated poly(oxyethylene) (PEO-MA) and p-vinylbenzyl-terminated (PEO-St) polyoxyethylene macromonomers and styrene (St), initiated by a water- and/or oil-soluble initiator, was investigated using conventional gravimetric and NMR methods at 60°C. The batch copolymerizations in the water/ethanol continuous phase were conducted to high conversion. The rate of polymerization was described by the curve with a maximum at very low conversion. The initial rate of polymerization and the number-average molecular weight were found to decrease with increasing [PEO-MA], and the decrease was more pronounced in the range of a high macromonomer concentration. The rate per particle (at ca. 20% conversion) was found to be proportional to the −1.55th, the particle size to the −0.92nd, and the number of particles (at final conversion) to the 3.2nd power of [PEO-MA], respectively. At the beginning of polymerization the continuous phase is the main reaction locus. As the polymerization advances, the reaction locus is shifted from the continuous phase to the polymer particles. The transform of the reaction loci from the continuous phase to the polymer particles increases the rate of polymerization and the polymer molecular weights. The increase of the weight ratio PEO-MA/St favors the formation of monodisperse polymer particles, the colloidal stability of dispersion, and the formation of a larger number of polymer particles. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 3131–3139, 1997     

Organic–inorganic copolymers with double‐decker silsesquioxane in the main chains by polymerization via click chemistry

A series of novel organic–inorganic copolymers with polyhedral oligomeric silsesquioxane (POSS) in the main chains were synthesized via the copper‐catalyzed Huisgen 1,3‐dipolar cycloaddition polymerization approach. Toward this end, we synthesized 3,13‐azidopropyloctaphenyl double‐decked silsesquioxane (DDSQ). This difunctional POSS macromer was used to copolymerize with α,ω‐dialkynyl‐terminated oligoethylenes with variable number of ethylene units. The organic–inorganic copolymers were obtained with the mass fraction of POSS up to 79%. Gel permeation chromatography showed that the high‐molecular‐weight copolymers were successfully obtained in all the cases. Differential scanning calorimetry showed that the amplitude of glass transitions for these copolymers was very feeble, suggesting that the segmental motions responsible for the glass transitions was highly restricted with DDSQ cages in the main chains. Thermogravimetric analysis showed that the organic–inorganic hybrid copolymers displayed extremely high thermal stability. Contact angle measurements showed that these organic–inorganic copolymers are highly hydrophobic and possessed very low surface energy. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4221–4232     

Studies on metathetical and thermal polymerization of 5-norbornene 2,3-dicarboximide end-capped resins Pt-II

The article deals with synthesis, characterization, and polymerization of 5-norbornene-2,3-dicarboximide end-capped resins (bisnadimides) based on 4,4′-diaminodiphenylether, 1,4/1,3-bis(4′-aminophenoxy) benzene, 2,2′-bis[4-(4′-aminophenoxy)phenyl]propane, and bis[4-(4′-aminophenoxy)phenyl]sulphone. Both exo and endo bisnadimides were prepared by reacting the aromatic diamines with exo or endo nadic anhydride in glacial acetic acid at 120°C. The exo or endo bisnadimides could be distinguished on the basis of differences observed in IR or ¹H-NMR spectra. Both thermal (in solid state) and metathetical polymerization (using WCl₆/tetramethyltin catalyst and chlorobenzene solvent) of bisnadimides was carried out. Only exo bisnadimides could be polymerized using metathesis reaction whereas thermal polymerization of both endo and exo bisnadimide could be successfully carried out at 300°C in static air atmosphere. The polymers were highly crosslinked and insoluble in common organic solvents. The polymers obtained by metathesis polymerization were light brown in color whereas those obtained by thermal polymerization were dark brown in color. Thermal stability of the thermally polymerized exo or endo bisnadimides was comparable. These polymers were stable up to 400°C and decomposed in a single step above this temperature. The char yield at 800°C depended on the structure of the polymer and was in the 39–56% range. The polymers formed by metathesis polymerization showed a 1–3% weight loss in the temperature range 226–371°C and decomposed in a single step above 440°C. The char yields were higher in these polymers (53–71%) compared to those obtained by thermal polymerization. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 2323–2331, 1997     

Higher aliphatic aldehyde polymers. VI. Poly(n-nonaldehyde)

Crystalline poly(n-nonaldehyde) (PNA) was prepared by anionic polymerization of n-nonaldehyde (NA) in methylcyclohexane (MCH) with lithium tertiary butoxide (LTB) as the initiator. Normal low-temperature conditions did not give polymer reprodusibly; however, when the polymerization was carried out with a gradual temperature decrease to ?60°C holding at this temperature followed by completion at ?78°C, a moderate yield of PNA was obtained. The polymer was acetate capped and characterized. Infrared and PMR spectroscopy, as well as degradation of the polymer in the presence of 2,4-dinitrophenylhydrazine to the hydrazone, conclusively proved the chemical structure of the polymer. VPO measurements and measurement of the inherent viscosity showed the polymer to be of moderate molecular weight. PNA is highly crystalline and shows two transition regions, one corresponding to the melting of the main chain at temperatures above 120°C and one region between 50 and 80°C, which is related to the crystallization of the aliphatic side chains. PNA, although inherently brittle, can be extruded through an orifice at a temperature near the side-chain melting temperature to give an extrudate whose x-ray patterns show the characteristics of a fiber diagram. It is suggested that the crystal structure of the PNA is similar to that of poly(n-heptaldehyde) but with a larger a spacing, which is expected from a longer aliphatic side chain.     

Synthesis of degradable crosslinked polymers based on 1,5-dioxepan-2-one and crosslinker of bis-ϵ-caprolactone type

Poly(lactones) may be crosslinked by ring-opening polymerization of the corresponding cyclic esters in the presence of tetrafunctional bis(ϵ-caprolactone). The homopolymer of 1.5-dioxepan-2-one (DXO) has poor mechanical properties but also some very good properties, such as biocompatibility and degradability. Crosslinking of degradable polymer based on the poly(ether-ester) DXO was performed with crosslinkers having the same reactivity as the monomer. 2,2-Bis(ϵ-caprolactone-4-yl)propane (BCP) and bis(ϵ-caprolactone-4-yl) (BCY) with tetrafunctionalities were synthesized from the corresponding diols and then used as comonomers during the polymerization of DXO. The comonomers showed the same reactivity to the initiator, stanneous 2-ethylhexanoic acid, as DXO and perfectly random crosslinked films were obtained. The crosslinked films showed a high degree of swelling already at 2–3 mol % BCP or BCY. The BCP crosslinker was somewhat less soluble in DXO at lower temperatures, but all BCP was soluble at 180°C. These polymeric films were elastic with no crystallinity and the T_g values increased from −39°C for pure DXO to −35°C for BCP crosslinked films and −21°C for BCY crosslinked ones. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 1635–1649, 1997     

Stereoselective polymerization of rac‐lactide with a bulky aluminum/Schiff base complex

An aluminum/Schiff base complex {[2,2-dimethyl-1,3-propylenebis(3,5-di-tert-butylsalicylideneiminato)](isopropanolato)aluminum(III) ( 2 )} based on a bulky ligand and aluminum isopropoxide was prepared and employed for the stereoselective ring-opening polymerization (ROP) of rac-lactide (rac-LA). The initiator was characterized with nuclear magnetic resonance (NMR), crystal structure measurements, and elemental analysis. It contained a five-coordinate aluminum atom that was trigonal bipyramidal in the solid state according to the crystal structure measurements. The two conformational stereoisomers of 2 exchanged quickly on the NMR scale. Compound 2 polymerized rac-LA into a crystalline polymer that was characterized with ¹H NMR, wide-angle X-ray diffraction, electrospray ionization mass spectrometry, and gel permeation chromatography. The kinetics of the polymerization were first-order in both the monomer and initiator, and there was a linear relationship between the rac-LA conversion and the number-average molecular weight of poly(rac-LA) with a narrow molecular distribution (1.04–1.08). These features showed that the polymerization was well controlled. The high melting temperature (196–201 °C) and isotacticity of poly(rac-LA) indicated that complex 2 was a highly stereoselective initiator for the ROP of rac-LA. The stereoselectivity was as high as 90%, and the stereoblocks of poly(rac-LA) by complex 2 contained an average of 20 units (average block length = 20) of enantiomerically pure lactic acid. The activation energy (23.6 kJ mol⁻¹) was obtained according to an Arrhenius equation. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5974–5982, 2004     

Construction of reversible hydration–dehydration system by a model compound and a novel polymer bearing vicinal tricarbonyl structure

A novel polymer bearing acyclic vicinal tricarbonyl moieties in the side chains was synthesized by (1) radical polymerization of a styrene derivative with a 1,3‐diketone structure and (2) successive treatment of the resulting polystyrene derivative by N‐bromosuccinimide to convert its 1,3‐diketone moiety in the side chains into the corresponding vicinal tricarbonyl moiety. The tricarbonyl moiety was highly reactive with water to permit its rapid conversion into a geminal diol structure in water‐containing acetone. On the other hand, heating the resulting polymer bearing the geminal diol structure under vacuum enabled successful recovery of the vicinal tricarbonyl moiety to demonstrate the reversible nature of this system, which allowed us to repeat the hydration–dehydration cycle without deteriorating the polymer structure. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis of polycarbonates by a silicon-assisted alkoxy/carbonylimidazolide coupling reaction

The investigation of a silicon-mediated coupling reaction between hydroxyl and carbonylimidazolide functional groups in the preparation of carbonate linkages is described. Application of this reaction to the formation of aliphatic polycarbonates was accomplished by the polymerization of an AB monomer unit, which was composed of 1,4-cyclohexanediol, where one of the hydroxyl groups was protected as a dimethylphenylsilyl ether and the other carried the carbonylimidazolide functionality. Reaction of this monomer with cesium fluoride removed the silicon protecting group and the resulting alkoxy anion promoted polymerization. Poly(1,4-cyclohexanecarbonate)s with typical molecular weights of M_w = 20,000 and M_n = 7300 a.m.u. (from GPC based upon polystyrene standards) were prepared in ca. 65% yield. The polymer showed a glass transition temperature at 138°C by DSC. TGA gave 85% mass loss between 275 and 350°C. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 1133–1137, 1997.