p-Nitroacetanilide in the presence of triethylamine as a photoinitiator system for vinyl polymerization

The polymerization rate of methyl methacrylate photosensitized by p-nitroacetanilide in the presence of triethylamine was measured as a function of the amine and monomer concentrations. The polymerization proceeds readily in high-polarity media (acetonitrile/monomer) but is negligible in nonpolar media. The polymerization rate increases with the amine concentration up to 0.15M. Further increase in amine concentration does not change the polymerization rate. A similar behavior was observed for the photobleaching of the nitro compound. ESR studies show the formation of a nitro and an amine free radical, the latter free radical being the active species that adds to the monomer. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 3095–3100, 1997     

Photoinitiated,inverse emulsion polymerization of acrylamide: Some mechanistic and kinetic aspects

The kinetics of photoinitiated, inverse emulsion polymerization of acrylamide with 2,2‐dimethoxy‐2‐phenylacetophenone (DMPA) as a photoinitiator was investigated under three different cases. First, in a quartz reactor transparent to full UV light, the polymerization rate (R_p) increased and then decreased with the change of initiator order from 0.27 to a negative value when the DMPA concentration was increased, and it was particularly unusual that monomer orders at different DMPA concentrations were lower than the first. Second, for polymerization without DMPA in a quartz reactor, the dependence of R_p on monomer concentration was similar to that of R_p on initiator concentration in the aforementioned case. Third, when polymerization was carried out in a Pyrex reactor where the far UV light was filtered, a peak rate was also observed, and initiator orders varied from 0.24 to a negative value; however, under this case monomer orders at different initiator concentrations were greater than the first. These results indicated that the effect of absorbance often observed in bulk or solution photopolymerization also existed in this system, and the self‐initiation of monomer had some influence on polymerization, and the role of primary radical termination could not be neglected, as evidenced by kinetic analysis. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 846–852, 2004     

Kinetic study of free‐radical polymerization photoinitiated by cyanine‐borate salts. II.

A series of cyanine butyltriphenylborate salts were prepared and tested as initiators of free‐radical polymerization photoinitiated via a photoinduced electron‐transfer process. For the majority of the tested series, the highest rate of photoinitiated free‐radical polymerization was observed when sec‐butyl radicals were formed. Essentially, there was no influence of the quantum yield of the free‐radical formation on the rate of the free‐radical polymerization initiated by the cyanine‐borate salts. The experimental data revealed that the relationship between the rate of polymerization and the free energy change for the electron transfer displayed typical Marcus region kinetic behavior. The photoreduction of the cyanine butyltriphenylborate salts produced colorless products. The efficiency of the bleached‐dye formation had no effect on the overall efficiency of photoinitiated polymerization. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2365–2374, 2000     

Photoinitiated polymerization of methacrylic monomers in a polystyrene matrix: Kinetic,mechanistic, and structural aspects

The kinetics and mechanism of the photoinitiated polymerization of tetrafunctional and difunctional methacrylic monomers [1,6‐hexanediol dimethacrylate (HDDMA) and 2‐ethylhexyl methacrylate (EHMA)] in a polystyrene (PS) matrix were studied. The aggregation state, vitreous or rubbery, of the monomer/matrix system and the intermolecular strength of attraction in the monomer/matrix and growing macroradical/matrix systems are the principal factors influencing the kinetics and mechanism. For the PS/HDDMA system, where a relatively high intermolecular force of attraction between monomer and matrix and between growing macroradical and matrix occurs, a reaction‐diffusion mechanism takes place at low monomer concentrations (<30–40%) from the beginning of the polymerization. For the PS/EHMA system, which presents low intermolecular attraction between monomer and matrix and between growing macroradical and matrix, the reaction‐diffusion termination is not clear, and a combination of reaction‐diffusion and diffusion‐controlled mechanisms explains better the polymerization for monomer concentrations below 30–40%. For both systems, for which a change from a vitreous state to a rubbery state occurs when the monomer concentration changes from 10 to 20%, the intrinsic reactivity and k_p/k_t^1/2 ratio (where k_p is the propagation kinetic constant and k_t is the termination kinetic constant) increase as a result of a greater mobility of the monomer in the matrix (a greater k_p value). The PS matrix participates in the polymerization process through the formation of benzylic radical, which is bonded to some extent by radical–radical coupling with the growing methacrylic radica, producing grafting on the PS matrix. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2049–2057, 2001     

Novel pyridinium salts as cationic thermal and photoinitiators and their photosensitization properties

Novel pyridinium salts [N‐(α‐phenylbenzyl)‐, N‐(1‐naphthylmethyl)‐, or N‐cinnamyl p‐ or o‐cyanopyridinium hexafluoroantimonates] were synthesized by the reaction of p‐ or o‐cyanopyridine and the corresponding bromides followed by anion exchange with KSbF₆. These pyridinium salts polymerized epoxy monomers at lower temperatures than previously reported for N‐benzyl‐2‐cyanopyridinium hexafluoroantimonate. The o‐substituted pyridinium salts showed higher activity than the p‐substituted ones, and the crosslinked epoxy polymers cured with these initiators showed higher glass‐transition temperatures. These pyridinium salts photoinitiated radical polymerization as well as cationic polymerization. The photopolymerization was accelerated by the addition of aromatic ketones as photosensitizers. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1037–1046, 2002     

Kinetic study of azidopentaammine cobalt(III) complex as photoinitiator and termination agent of N‐vinylpyrrolidone radical polymerization

N‐Vinylpyrrolidone polymerization photoinitiated at 365 and 546 nm by azidopentaammine cobalt(III) {[Co(NH₃)₅N₃]²⁺} was investigated at room temperature in an argon atmosphere. By excitation into the ligand to metal charge transfer (LMCT), the cobalt complex showed an efficient photoredox process leading to the formation of a cobalt(II) and an azide radical (N, Φ_photoredox = 0.24). The same process was found to occur by excitation into the ligand field band with a low but not negligible quantum yield (Φ_photoredox = 0.016). Two different domains were clearly present when the plot of the rate of polymerization as a function of the cobalt(III) complex was studied; for [Co(III)] < 2.0 × 10⁻⁴ M, the termination step mainly involved a mutual annihilation of growing radicals whereas an oxidative termination was present in the range of 2.0 × 10⁻⁴ M < [Co(III)] < 1.0 × 10⁻³ M. Within the former domain the rate of polymerization (R_p ) varied with the first power of the monomer concentration and with the square root of the absorbed light intensity while for the latter domain the R_p was proportional to the monomer concentration and absorbed light intensity. Further investigations using the viscosity‐average molecular weight data allowed us to corroborate the proposed polymerization mechanism. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3997–4005, 2000     

Tuning the sugar‐response of boronic acid block copolymers

A detailed study of the pH‐ and sugar‐responsive behavior of poly(3‐acrylamidophenylboronic acid pinacol ester)‐b‐poly(N,N‐dimethylacrylamide) (PAPBAE‐b‐PDMA) block copolymers is presented. Reversible addition‐fragmentation chain transfer (RAFT) polymerization of the pinacol ester of 3‐acrylamidophenylboronic acid resulted in homopolymers with molecular weights between 12,000 and 37,000 g/mol. The resulting homopolymers were employed as macro‐chain transfer agents during the polymerization of N,N‐dimethylacrylamide (DMA). Successful chain extension and removal of the pinacol protecting groups to yield poly(3‐acrylamidophenylboronic acid)‐b‐PDMA (PAPBA‐b‐PDMA) with free boronic acid moieties resulted in pH‐ and sugar‐responsive block copolymers that were subsequently investigated for their behavior in aqueous solution. The PAPBA‐b‐PDMA block copolymers were capable of solution self‐assembly due to the PAPBA block being water‐insoluble below its pK_a. The resulting aggregates were demonstrated to solubilize and release model hydrophobic compounds, as demonstrated by fluorescence studies. Dissociation of the aggregates was induced by raising the pH above the pK_a of the boronic acid residues or by adding sugars capable of forming boronate esters. Aggregate size, dissociation kinetics, and the effect of various sugars were considered. The critical sugar concentration needed to induce aggregate dissociation was tuned by incorporation of hydrophilic DMA units within the PAPBA responsive segment to yield PDMA‐b‐poly(3‐acrylamidophenylboronic acid‐co‐DMA) block copolymers. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Polymerization of vinyl monomers photoinitiated by p‐nitroaniline: Photoinitiation mechanism

The polymerization rate of methyl methacrylate photoinitiated by p‐nitroacetanilide in the presence of triethylamine was measured as a function of the amine concentration in different media. The polymerization is more efficient in nonpolar medium (benzene/monomer). ESR studies show the formation of a nitro and an amino free radical, which are formed by photoinduced proton transfer from the amine to the nitro group. The amine radical is the active species that adds to the monomer. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2269–2273, 2000     

Polyacrylamide cryogels by photoinitiated free radical polymerization

A novel method for the preparation of poly(acrylamide) cryogels by photoinitiated polymerization of monomeric precursors was described. A series of poly(acrylamide) cryogels were easily prepared by irradiating aqueous solutions containing acrylamide and N,N′‐methylene(bis)acrylamide as monomer and cross‐linker, respectively, in the presence of 1‐[4‐(2‐hydroxyethoxy)phenyl]‐2‐hydroxy‐2‐methyl‐1‐propane‐1‐one (Irgacure 2959) as water‐soluble photoinitiator with the help of freezing–thawing procedures. Photolysis was conducted at ?13 °C isothermally through specially designed cryostat‐integrated Rayonet merry‐go‐round photoreactor. On comparing the described photochemical method with the conventional redox counter part, the polymerization is initiated, and gelation proceeds only on external stimulation by light. This way, concomitant hydrogel formation usually observed with the redox process as a result of premature polymerization during the cooling process was prevented. The obtained cryogels exhibited superfast swelling behavior. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Sulfobetaine‐containing diblock and triblock copolymers via reversible addition‐fragmentation chain transfer polymerization in aqueous media

A novel bifunctional acrylamido‐based reversible addition–fragmentation chain transfer (RAFT) chain‐transfer agent (CTA), N,N′‐ethylenebis[2‐(thiobenzoylthio)propionamide] (CTA2), has been synthesized and used for the controlled free‐radical polymerization of N,N‐dimethylacrylamide (DMA). A comparative study of CTA2 and the monofunctional CTA N,N‐dimethyl‐s‐thiobenzoylthiopropionamide (CTA1) has been conducted. Polymerizations mediated by CTA1 result in poly(N,N‐dimethylacrylamide) (PDMA) homopolymers with unimodal molecular weight distributions, whereas CTA2 yields unimodal, bimodal, and trimodal distributions according to the extent of conversion. The multimodal nature of the PDMAs has been attributed to termination events and/or chains initiated by primary radicals. The RAFT polymerization of DMA with CTA2 also results in a prolonged induction period that may be attributed to the higher local concentration of dithioester functionalities early in the polymerization. A series of ω‐ and α,ω‐dithioester‐capped PDMAs have been prepared in organic media and subsequently employed as macro‐CTAs for the synthesis of diblock and triblock copolymers in aqueous media with the zwitterionic monomer 3‐[2‐(N‐methylacrylamido)‐ethyldimethylammonio] propane sulfonate (MAEDAPS). Additionally, an ω‐dithioester‐capped MAEDAPS homopolymer has been used as a macro‐CTA for the block polymerization of DMA. To our knowledge, this is the first example of a near‐monodisperse, sulfobetaine‐containing block copolymer prepared entirely in aqueous media. The diblock and triblock copolymers form aggregates in pure water that can be dissociated by the addition of salt, as determined by ¹H NMR spectroscopy and dynamic light scattering. In pure water, highly uniform, micellelike aggregates with hydrodynamic diameters of 71–93 nm are formed. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1262–1281, 2003     

Synergistic interaction of epoxides and N‐vinylcarbazole during photoinitiated cationic polymerization

A kinetic study was conducted of the independent photoinitiated cationic polymerization of a number of epoxide monomers and mixtures of these monomers with N‐vinylcarbazole. The results show that these two different classes of monomers undergo complex synergistic interactions with one another during polymerization. It was demonstrated that N‐vinylcarbazole as well as other carbazoles are efficient photosensitizers for the photolysis of both diaryliodonium and triarylsulfonium salt photoinitiators. In the presence of large amounts of N‐vinylcarbazole, the rates of the cationic ring‐opening photopolymerization of epoxides are markedly accelerated. This effect has been ascribed to a photoinitiated free‐radical chain reaction that results in the oxidation of monomeric and polymeric N‐vinylcarbazole radicals by the onium salt photoinitiators to generate cations. These cations can initiate the ring‐opening polymerization of the epoxides, leading to the production of copolymers. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3697–3709, 2000     

Photoinitiated dispersion polymerization of methyl methacrylate: A quick approach to prepare polymer microspheres with narrow size distribution

Photoinitiated dispersion polymerization of methyl methacrylate was carried out in a mixture of ethanol and water as dispersion medium in the presence of poly(N‐vinylpyrrolidone) (PVP) as the steric stabilizer and Darocur 1173 as photoinitiator. 93.7% of conversion was achieved within 30 min of UV irradiation at room temperature, and microspheres with 0.94 μm number–average diameter and 1.04 polydispersity index (PDI) were obtained. X‐ray photoelectron spectroscope (XPS) analysis revealed that only parts of surface of the microspheres were covered by PVP. The particle size decreased from 2.34 to 0.98 μm as the concentration of PVP stabilizer increased from 2 to 15%. Extra stabilizer (higher than 15%) has no effect on the particle size and distribution. Increasing medium polarity or decreasing monomer and photoinitiator concentration resulted in a decrease in the particle size. Solvency of reaction medium toward stabilizer, which affects the adsorption of stabilizer on the particle surface, was shown to be crucial for controlling particle size and uniformity because of the high reaction rate in photoinitiated dispersion polymerization. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1329–1338, 2008     

Reversible addition–fragmentation chain transfer polymerization of 2‐naphthyl acrylate with 2‐cyanoprop‐2‐yl 1‐dithionaphthalate as a chain‐transfer agent

The reversible addition–fragmentation chain transfer (RAFT) polymerizations of 2‐naphthyl acrylate (2NA) initiated by 2,2′‐azobisisobutyronitrile were investigated with 2‐cyanoprop‐2‐yl 1‐dithionaphthalate (CPDN) as a RAFT agent at various temperatures in a benzene solution. The results of the polymerizations showed that 2NA could be polymerized in a controlled way by RAFT polymerization with CPDN as a RAFT agent; the polymerization rate was first‐order with respect to the monomer concentration, and the molecular weight increased linearly with the monomer conversion. The polydispersities of the polymer were relatively low up to high conversions in all cases. The chain‐extension reactions of poly(2‐naphthyl acrylate) (P2NA) with methyl methacrylate and styrene successfully yielded poly(2‐naphthyl acrylate)‐b‐poly(methyl methacrylate) and poly(2‐naphthyl acrylate)‐b‐polystyrene block polymers, respectively, with narrow polydispersities. The P2NA obtained by RAFT polymerization had a strong ultraviolet absorption at 270 nm, and the molecular weights had no apparent effect on the ultraviolet absorption intensities; however, the fluorescence intensity of P2NA increased as the molecular weight increased and was higher than that of 2NA. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2632–2642, 2005     

Photoinitiated polymerization of methacrylic monomers in a polybutadiene matrix (PB): Kinetic,mechanistic, and structural aspects

The kinetics and mechanism of the photoinitiated polymerization of tetrafunctional and difunctional methacrylic monomers [1,6‐hexanediol dimethacylate (HDDMA) and 2‐ethylhexyl methacrylate (EHMA)] in a polybutadiene matrix (PB) have been studied. The maximum double‐bond conversion, the maximum polymerization rate, the intrinsic reactivity, and the kinetic constants for propagation and termination have been calculated. Unlike the behavior followed by the SBS‐HDDMA and PS‐HDDMA systems, where a reaction‐diffusion mechanism occurs from the start of the polymerization at low monomer concentrations (<30–40%), in the PB‐HDDMA system the reaction diffusion controls the termination process only after approximately 10% conversion is reached, as for the bulk polymerization of polyfunctional methacrylic monomers. Before reaching 10% conversion the behavior observed can be better explained by a combination of segmental diffusion‐controlled (autoaccelerated) and reaction‐diffusion mechanisms. This is probably a consequence of the lower force of attraction between the monomer and the matrix and between the growing macroradical and the matrix than those corresponding to the other systems mentioned. For the PB‐EHMA system, the termination mechanism is principally diffusion‐controlled from the beginning of the polymerization for monomer concentrations below 30–40%, and for higher monomer concentrations, a standard termination mechanism takes place (k_t ≈ 10⁶) at low double‐bond conversions, which is diffusion‐controlled for high conversions (>40%). For PB‐HDDMA and PB‐EHMA systems, crosslinked polymerized products are obtained as a result of the participation of the double bonds of the matrix in the polymerization process. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2444–2453, 2001     

Room‐temperature RAFT copolymerization of 2‐chloroallyl azide with methyl acrylate and versatile applications of the azide copolymers

A new vinyl azide monomer, 2‐chlorallyl azide (CAA), has been synthesized from commercially available reagent in one step. The reversible addition fragmentation chain transfer (RAFT) copolymerization of CAA with methyl acrylate (MA) was carried out at room temperature using a redox initiator, benzoyl peroxide (BPO)/N,N‐dimethylaniline (DMA), in the presence of benzyl 1H‐imidazole‐1‐carbodithioate (BICDT). The polymerization results showed that the process bears the characteristics of controlled/living radical polymerizations, such as the molecular weight increasing linearly with the monomer conversion, the molecular weight distribution being narrow, and a linear relationship existing between ln([M]₀/[M]) and the polymerization time. Chain extension polymerization was performed successfully to prepare block copolymer. Furthermore, the azide copolymers were functionalized by Cu^I‐catalyzed “click” reaction with alkyne‐containing poly(ethylene glycol) (PEG) to yield graft copolymers with hydrophilic PEG side chains. Surface modification of the glass sheet was successfully achieved via the crosslinking reaction of the azide copolymer under UV irradiation at ambient temperature. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1348–1356, 2010     

High solids TEMPO‐mediated radical semibatch emulsion polymerization of styrene

A bicomponent initiation system consisting of 2,2,6,6‐tetramethylpiperidine‐N‐oxyl (TEMPO) and the water soluble initiator potassium persulfate (KPS) was used to develop a robust and versatile semibatch emulsion polymerization process to obtain polystyrene (PS) latexes with solids contents of 5–40 wt %. A window of operating conditions was found that yielded high conversion (>95%) stable latexes and well controlled polymers, overcoming limitations found in previous attempts at developing similar processes using TEMPO. The critical parameters studied were surfactant concentration, monomer concentration in the nucleation step and the monomer feed rate in the semibatch step. Methyl acrylate (MA) was used in the nucleation step to improve the nitroxide efficiency (N_Eff). Latexes having molecular weight distribution (MWD) with dispersity (?) lower than 1.5, average particle size (D_p) from ≈32 to ≈500 nm, nitroxide efficiencies N_Eff up to ≈1.0 and monomer conversions >90% were obtained in less than 12 h with solids contents up to 40 wt %. These results constitute a significant advance over prior efforts in TEMPO‐mediated polymerization in aqueous dispersions. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 49–62     

Synthesis of polymers by template polymerization. I. Template polymerization of poly(methacrylic acid) with β‐cyclodextrin

A novel template monomer with multiple methacryloyl groups was synthesized with β‐cyclodextrin by the acetylation of primary hydroxyl groups and the esterification of secondary hydroxyl groups with methacrylic acid anhydride. The average number of methacryloyl groups in the monomer was 11. The radical polymerization of the monomer was carried out with the following initiators: α,α′‐azobisisobutylonitrile, H₂O₂? Fe²⁺ redox initiator, p‐xylyl‐N,N‐dimethyldithiocarbamate (XDC), and α‐bromo‐p‐xylyl‐N,N‐dimethyldithiocarbamate (BXDC). When the concentration of the monomer was less than 4.12 × 10^?3 M, polymerization was limited inside the molecule, and gelation of the system was hindered. For controlled radical photopolymerization with XDC and BXDC, the methacryloyl groups of the monomer were homogeneously polymerized, and poly(methacrylic acid) with a narrow molecular weight distribution was obtained by the hydrolysis of the polymerized products. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3539–3546, 2001     

Tetraalkylammonium salt as photoinitiator of vinyl polymerization in organic and aqueous media: A mechanistic and laser flash photolysis study

N‐Dimethyl‐N‐[2‐(N,N‐dimethylamino)ethyl]‐N‐(1‐methylnaphthyl)ammonium tetrafluoroborate ( I ) was synthesized with the aim of obtaining a versatile photoinitiator for vinyl polymerization in organic solvents and water. Salt I was able to trigger the polymerization of acrylamide, 2‐hydroxyethylmethacrylate and styrene even at very low concentrations of the salt (～1.0 × 10^?5 M). Using laser flash photolysis and fluorescence techniques and analyzing the photoproduct distribution, we were able to postulate a mechanism for the photodecomposition of the salt. With irradiation, I undergoes an intramolecular electron‐transfer reaction to form a radical ion pair (RIP). The RIP intermediate decomposes into free radicals. The RIP and the free radicals are active species for initiating the polymerization. Depending on the concentration of the vinyl monomers studied, the initiation mechanism of the polymerization reaction changes. At large monomer concentrations, the RIP state is postulated to trigger the reaction by generating the anion radical of the olefin substrate. At a low monomer concentration, the free radicals produced by the decomposition of I are believed to start the chain reaction. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 901–913, 2002; DOI 10.1002/pola.10166     

Effects of the reaction parameters on the properties of thermosensitive poly(N‐isopropylacrylamide) microspheres prepared by precipitation and dispersion polymerization

Poly(N‐isopropylacrylamide) (PNIPAAm)‐based microspheres were prepared by precipitation and dispersion polymerization. The effects of several reaction parameters, such as the type and concentration of the crosslinker (N,N′‐methylenebisacrylamide or ethylene dimethacrylate), medium polarity, concentration of the monomer and initiator, and polymerization temperature, on the properties were examined. The hydrogel microspheres were characterized in terms of their chemical structure, size and size distribution, and morphological and temperature‐induced swelling properties. A decrease in the particle size was observed with increasing polarity of the reaction medium or increasing concentration of poly(N‐vinylpyrrolidone) as a stabilizer in the dispersion polymerization. The higher the content was of the crosslinking agent, the lower the swelling ratio was. Too much crosslinker gave unstable dispersions. Although the solvency of the precipitation polymerization mixture controlled the PNIPAAm microsphere size in the range of 0.2–1 μm, a micrometer range was obtained in the Shellvis 50 and Kraton G 1650 stabilized dispersion polymerizations of N‐isopropylacrylamide in toluene/heptane. Typically, the particles had fairly narrow size distributions. Copolymerization with the functional glycidyl methacrylate monomer afforded microspheres with reactive oxirane groups. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 968–982, 2006