Study of the interference problems of dioxin-like chemicals with the bio-analytical method CALUX

The reporter gene expression method CALUX has proven to be a very valuable screening technique for assessing toxic equivalents of dioxins and dioxin-like compounds, because it detects all AhR ligands in a variety of sample matrices. However, the exact meaning of the CALUX response is difficult to evaluate for complex mixtures mainly since not all AhR ligands are known and since antagonistic or synergistic effects occurs.

In this paper, non-additive effects on the CALUX response of dioxins were investigated for a limited number of dioxin-like compounds in concentration ranges that are 10²–10⁸ times higher than that of 2,3,7,8-TCDD. Antagonistic effects are detected for three Aroclors (1242, 1254, 1260), Halowax 1014 (PCN), HCB and PBB 169. The ratios, Aroclor/dioxin, Halowax/dioxin and HCB/dioxin, needed to observe an antagonistic effect are 10 000, 5000 and 50 000, respectively. No significant deviation from additivity was observed for Aroclor 5442 (PCT) and PBB 77 in the concentration range investigated.

Two clean-up procedures have also been tested: in some cases the non-additive effects disappeared or were strongly reduced. Using only an acidic silica column, the classical dioxin-like compounds investigated here (PCB, PCT, PBB, PCN, HCB) as well as the dioxins are collected and analyzed altogether in one fraction. Consequently, no major alteration of the non-additive effects is expected. An acidic silica column combined with an activated carbon column allows the separation of PCDD/F and dioxin-like PCB in two different fractions, PBB 169 is completely eluted in the dioxin fraction and PBB 77 is distributed between the PCB and dioxin fraction. HCB is completely separated from the PCDD/F fraction.     

High-throughput capillary gas chromatography for the determination of polychlorinated biphenyls and fatty acid methyl esters in food samples

High-throughput capillary gas chromatography (CGC) methods, developed during the Belgian 1999 "dioxin" food crisis, for the determination of the contaminating polychlorinated biphenyls (PCBs) and the fatty acid composition of the lipids are described. For PCB analysis, the fat obtained by ultrasonic extraction is fractionated by matrix solid-phase dispersion, and the PCBs are analyzed by CGC-electron capture detection on a 10-mL x 100-microm-i.d. HP-5MS column. Analytical conditions for the high-speed column are deduced from analyses on conventional CGC columns using the method translation software. The concept of retention time locking is implemented to facilitate the elucidation of the PCB markers. The fatty acid methyl esters (FAMEs) are prepared by the sodium methylate procedure on part of the ultrasonic extract followed by analysis on 10-mL x 100-microm-i.d. HP-WAX or BPX-70 capillary columns. By optimizing both the sample preparation and CGC analysis, the throughput is more than fifty PCB and FAME samples per day with the same robustness as conventional methods.     

Use of Carbon-13 Labelled Dioxins Mixture for Analysis of Polychlorinated Dibenzo-p-Dioxins in Environmental Samples by GC-MS

Abstract

Positive identification and quantitation of polychlorinated dibenzo-p-dioxins (PCDD) in complicated environmental samples is described using a C-13 labelled dioxin mixture as an internal reference standard. Environmental samples are spiked with the C-13 labelled dioxin mixture and monitored for labelled and unlabelled dioxins using GC-MS in the electron impact selected ion monitoring (EISIM) mode. The C-13 labelled dioxin mixture and a municipal solid waste (MSW) incinerator fly ash extract show the same number of isomers in each tetra to octa-chlorodioxin congener groups. Quantitation of the C-13 labelled dioxin mixture was carried out using a reference standard mixture of unlabelled dioxins consisting of at least one isomer for each congener group. The C-13 labelled dioxin standard is highly useful for the determination of retention windows for tetra- to octa-chlorodioxins, identification of dioxins in each congener group, and calculation of the recovery of dioxins in samples that require extensive sample clean-up prior to GC-MS analysis. Its application for retention time window determination and as an internal reference standard for quantitation of dioxins in MSW incinerator fly ash extract and identification of dioxins in a complex sample from a PCB fire is demonstrated.     

Levels of seven PCBs used as markers of dioxin in commercial pork meat in Spain.

The levels of 7 PCBs used as markers of dioxin in 62 pork meat samples (head, loin, and dewlap) were determined by supercritical fluid extraction and gas chromatography with electron capture detection. Analytical limits of detection for the individual congeners ranged from 0.048 to 0.2 ng/g dry wt. PCB congeners 153 and 180 were detected in all samples. Among congeners in general, PCB 52, 101, and 153 were the most abundant. There was a linear relationship with a good correlation between PCB 101 and PCB 52.     

Importance of clean-up for comparison of TEQ-values obtained by CALUX and chemo-analysis

This paper presents Chemically Activated LUciferine gene eXpression (CALUX) TEQ-values obtained for nine plasma samples following two different purification procedures, one of them involving fractionation. CALUX results obtained for the dioxin (DX) and dioxin + PCB (DX + PCB) fractions were then compared to the GC-HRMS TEQ-values calculated for the 17 polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (17 PCDD/F) and 17 PCDD/F + 4 cPCB congeners, respectively. The overestimation of the CALUX (DX fraction) TEQ-values in comparison with the chemo-analyses of the 17 PCDD/F is mainly explained by the presence of other AhR agonists, like brominated compounds. Otherwise, the constancy of the CALUX (DX + PCB fraction) TEQ-value which compares to increasing the GC-HRMS (17 PCDD/F + 4 cPCB) TEQ results raises questions concerning (1) the significance of CALUX results obtained without fractionation as well as (2) the toxicological effect of a cocktail of contaminants on the human health.     

Fast and parallel determination of PCB 77 and PCB 180 in plasma using ultra performance liquid chromatography with diode array detection: A pharmacokinetic study in Swiss albino mouse

A simple, sensitive and reproducible ultra‐performance liquid chromatography (UPLC) method has been developed and validated for simultaneous estimation of polychlorinated biphenyl (PCB) 77 and PCB 180 in mouse plasma. The sample preparation was performed by simple liquid–liquid extraction technique. The analytes were chromatographed on a Waters Acquity H class UPLC system using isocratic mobile phase conditions at a flow rate of 0.3 mL/min and Acquity UPLC BEH shield RP₁₈ column maintained at 35°C. Quantification was performed on a photodiode array detector set at 215 nm and PCB 101 was used as internal standard (IS). PCB 77, PCB 180, and IS retention times were 2.6, 4.7 and 2.8 min, respectively, and the total run time was 6 min. The method was validated for specificity, selectivity, recovery, linearity, accuracy, precision and sample stability. The calibration curve was linear over the concentration range 10–3000 ng/mL for PCB 77 and PCB 180. Intra‐ and inter‐day precisions for PCBs 77 and 180 were found to be good with CV <4.64%, and the accuracy ranged from 98.90 to 102.33% in mouse plasma. The validated UPLC method was successfully applied to the pharmacokinetic study of PCBs 77 and 180 in mouse plasma.     

Quantitative determination of toxic mono- and non-ortho polychlorinated biphenyls in cod liver oil after selective liquid chromatographic separation

Summary By application of chromatographic column filled with Supelclean ENVI-Carb/Celite and elution with three solvents of different polarity three PCB fractions were obtained. Fraction A contained poly-ortho PCBs, Fraction B mono-ortho PCBs, and Fraction C non-ortho PCBs. The Supelclean ENVI-Carb/Celite column was used in combination with a sample preparation procedure for pre-cleaning of acid-stable chlorinated hydrocarbons such as DDT and its metabolites, HCH isomers, and regulation-relevant PCB congeners. The method was optimized using standard solutions of 55 PCB congeners, 8 chlorinated pesticides and contaminated cod liver oil samples. The influence of traces of remaining matrix on the elution profile of the organochlorine compounds on Supelclean ENVI-Carb/Celite was observed. Quantitation was carried out by GC-ECD with fused silica capillary columns of different polarity.     

Importance of REP values when comparing the CALUX bioassay results with chemoanalyses results: Example with spiked vegetable oils

Differences between chemical activated luciferase gene expression (CALUX) bioassay and chemoanalyses results are observed.

This paper shows that calculations of the TEQ values using REP values instead of WHO TEF values give different results. The REP values do affect the results obtained by the CALUX technique. These differences are more marked for the dioxin like PCB compounds (CALUX TEQ values are lower than WHO TEQ values) than for the dioxin compounds (CALUX TEQ values are higher than WHO TEQ values).

The CALUX results were compared with the concentrations of the congeners’ spiked into the oil.     

PCDD, PCDF, AND DL-PCB analysis in food: performance evaluation of the high-resolution gas chromatography/low-resolution tandem mass spectrometry technique using consensus-based samples

Due to safety concerns regarding dietary exposure to POPs, regulatory bodies are issuing detailed guidelines for testing for polychlorodibenzodioxins (PCDDs) and polychlorodibenzofurans (PCDFs) ('dioxins') and dioxin‐like (DL)‐PCBs in foods of animal origin. Determination of the aforesaid chemicals at regulatory levels requires highly selective and sensitive testing techniques. The new generation of low‐resolution mass spectrometers (triple quadrupoles) allows very low levels of quantification to be reached (in the order of tens of femtograms), thus suggesting a potential for their application in food and feed analysis. The performance of the low‐resolution tandem mass spectrometry (LRMS/MS) approach with triple quadrupoles was assessed on a qualified set of food samples from proficiency tests (PTs) and defense analysis. Accuracy was tested comparing the results with data from high‐resolution mass spectrometry (HRMS) and with consensus values from PTs. The cumulative TEQ results were characterized by deviations not exceeding 15% of PCDD + PCDF, DL‐PCB, and PCDD + PCDF + DL‐PCB (TEQ_TOT) reference consensus values (sample TEQ_TOT range, 2.29–25.1 pgWHO‐TEQ₉₇/g fat). Congener analytical variabilities did not influence significantly the WHO‐TEQ₉₇ outcome of the corresponding sample. This preliminary performance evaluation highlights the potential of LRMS/MS as a routine technique for quantitative analysis of PCDDs, PCDFs, and DL‐PCBs in food. Copyright © 2011 John Wiley & Sons, Ltd.     

Enhanced comprehensive two-dimensional gas chromatographic resolution of polychlorinated biphenyls on a non-polar polysiloxane and an ionic liquid column series

A total of 196 out of 209 polychlorobiphenyl (PCB) congeners were resolved using GC×GC-TOFMS with a non-polar/ionic liquid column series consisting of poly(50%-n-octyl-50%-methyl)siloxane and (1,12-di(tripropylphosphonium)dodecane bis(trifluoromethansulfonyl)amide) in the first and second dimension, respectively. It has been found that 13 PCB congeners overlap in five doublets (CB12+CB13, CB62+CB75, CB70+CB76, CB97+CB125 and CB153+CB168) and one triplet (CB90+CB101+CB113). All toxic, "dioxin like" congeners were separated with no interferences from any PCB congener. The 109 PCBs present in Aroclor 1242 and the 82 PCBs present in Aroclor 1260 were resolved GC×GC-TOFMS analysis on this column set.     

Validation of the CALUX bioassay for PCDD/F analyses in human blood plasma and comparison with GC-HRMS

Following the dioxin crisis of 1999, several studies were conducted to assess the impact of this crisis on the dioxin body burden in the Belgian population. The Scientific Institute of Public Health identified a population from whom plasma samples were available and from whom, during the follow up survey, plasma samples were obtained in 2000. In total, 496 samples were collected for GC-HRMS and CALUX analyses to verify statistical assessment conclusions. This study was seen as an opportunity to validate the CALUX bioassay for biological sample analysis and to compare toxic equivalency (TEQ) values obtained by the reference GC-HRMS technique and by the screening method. This article focuses on the validation results of the CALUX bioassay for the analyses of the dioxin fractions of blood plasma. The sample preparation is based on a liquid–liquid extraction, followed by an acid silica in series with an activated carbon clean-up. A good recovery (82%) and reproducibility (coefficient of variation less than 25%) were found for this method. Based on 341 plasma samples, a significant correlation was established between the bioassay and chemical method (R = 0.64). However, a proportional systematic error was observed when the results obtained with the CALUX bioassay were regressed with the results from the GC-HRMS analyses. The limit of quantification (LOQ) used to calculate TEQ values from the GC-HRMS determinations, the use of the relative potency values instead of the toxic equivalent factor and the potential of CALUX bioassay to measure all compounds with affinity for the AhR may partly explain this proportional systematic error. Nevertheless, the present results suggest that the CALUX bioassay could be a promising valid screening method for human blood plasma analyses.     

Importance of REP values when comparing the CALUX bioassay results with chemoanalyses results Example with spiked vegetable oils

Differences between chemical activated luciferase gene expression (CALUX) bioassay and chemoanalyses results are observed.This paper shows that calculations of the TEQ values using REP values instead of WHO TEF values give different results. The REP values do affect the results obtained by the CALUX technique. These differences are more marked for the dioxin like PCB compounds (CALUX TEQ values are lower than WHO TEQ values) than for the dioxin compounds (CALUX TEQ values are higher than WHO TEQ values).The CALUX results were compared with the concentrations of the congeners’ spiked into the oil.     

Determination of polychlorinated biphenyls by fast chromatography mass-spectrometry in environmental and biological samples

A method for the determination of polychlorinated biphenyls (PCB) by fast gas chromatography coupled with mass-spectrometric detection in selective ion monitoring mode has been developed. Chromatographic separation was carried out with HT-8 column (30 m × 0.25 mm) under sharp temperature increase from 80 to 320°C at a rate of 40°C/min. Duration of chromatography is 10 min. Fast chromatography conditions suggested by authors makes it possible to increase S/N ratios 10 times and so to reduce significantly the representative weight of the sample and develop an effective sample preparation technique. The method was used for PCB determination in Baikal area samples such as soil, snow, sediments from Lake Baikal and its tributaries, tissues of Baikal omul (Coregonus migratorius, Georgi, 1775) and blubber of Baikal seal (Phoca sibirica Gm.). The sample preparation stage includes PCB extraction from environmental samples and hydrolyzate of biological material with the following cleanup of the extract on the compact silica gel and florisil cartridges (0.5 g of the sorbent). The method enables the measurements of total PCBs and isomer groups of the same chlorination level with interlaboratory precision of no greater than 10% and the determination of indicator congeners (PCBs 28, 52, 101, 118, 138, 153, and 180) with a precision not exceeding 15%.     

Evaluation of automated direct sample introduction with comprehensive two-dimensional gas chromatography/time-of-flight mass spectrometry for the screening analysis of dioxins in fish oil

An automated direct sample introduction technique coupled to comprehensive two-dimensional gas chromatography-time of flight mass spectrometry (DSI-GC x GC/TOF-MS) was applied for the development of a relatively fast and easy analytical screening method for 17 polychlorinated dibenzo-p-dioxins/dibenzofurans (PCDD/Fs) and 4 non-ortho polychlorinated biphenyls (PCBs) in fish oil. Comparison of instrumental performance between DSI-GC x GC/TOF-MS and the traditional gas chromatographic high resolution mass spectrometric (GC-HRMS) method showed good agreement of results for standard solutions analyzed in blind fashion. Relatively high tolerance of the DSI technique for lipids in the final extracts enabled a streamlined sample preparation procedure that only required gel permeation chromatography (GPC) and solid-phase extraction (SPE) cleanup with graphitized carbon black. The sample size for the method was 2g of cod liver oil, which achieved limits of quantitation (LOQs) of 0.019-7.8 pg/g toxic equivalent quotients for the individual PCDD/Fs. Lower detection limits can be achieved by using larger sample size and scaling up the sample preparation procedure, but this adds to the labor, time, solvent consumption, and expense of the approach. However, the streamlined method yielded 0.94 pg/g and 2.3 pg/g LOQs for 2,3,7,8-tetrachloro dibenzofuran (TCDF) and 3,3',4,4',5-pentachloro biphenyl (CB126), which were sufficiently low for regulatory monitoring of 2g samples. Therefore, instead of congener specific analysis, this streamlined analytical screening method for TCDF and CB126 has the potential to monitor fish oil contaminated with dioxin and dioxin-like PCBs at or above current food safety limits. Acceptable recoveries for nearly all analytes at three different spiking levels in fish oil samples were achieved with good repeatability.     

Analysis of polychlorinated biphenyls in transformer oils by automated on-line coupling reversed phase liquid chromatography-gas chromatography using the through oven transfer adsorption desorption (TOTAD) Interface

An automated method for the direct analysis of polychlorinated biphenyls (PCBs) in transformer oil is presented. The proposed method uses the TOTAD (through oven transfer adsorption desorption) interface for the on-line coupling of reversed phase liquid chromatography and gas chromatography (RPLC-GC). In this fully automated system, the oil is injected directly with no sample pre-treatment step other than dilution with n-propanol and filtration. In the LC step, PCBs are separated from other components of the oils using methanol/water (90:10 v/v) as mobile phase, at a flow rate of 1?mL?min^?1. The LC fraction containing the PCBs is automatically transferred to the GC by the TOTAD interface and GC analysis enables the separation of the PCB congeners. The proposed method is compared with two other methods: the European Norm (UNE-EN-61619) and that of the American Society for Testing and Materials (ASTM) (D4059-00). The proposed method practically eliminates the time-consuming sample preparation step and avoids errors caused by sample manipulation. The total PCB concentrations obtained with the three methods are similar.     

Congener-specific determination of dioxins and related compounds by gas chromatography coupled to LRMS,HRMS, MS/MS and TOFMS

Their characteristics as persistent organic pollutant and their toxicity (2,3,7,8-TCDD is named as a known human carcinogen) make the dioxins and related compounds a focus of interest in environmental analytical chemistry. In view of the widespread distribution of dioxins in the environment, these compounds must be monitored in several matrices, such as air, effluents, soil, sludge and biological samples. The analytical methodologies are especially difficult owing to the complexity of the mixtures of congeners (210 PCDD/Fs and 209 PCBs) and to the low detection limits required (ppb to ppq). Moreover, time-consuming sample preparation steps are needed owing to the presence of a large number of interfering compounds. The different toxicity of each congener requires the development of congener specific methods. This review of trace dioxin determination by mass spectrometry (MS) includes sample preparation and chromatographic separation. In this Special Feature, the use of different MS techniques such as low-resolution MS (LRMS) and high-resolution MS (HRMS) is discussed in terms of selectivity and sensitivity. The performances of other MS techniques, such as tandem MS (MS/MS) and time-of-flight MS (ToFMS), are compared. Quantification techniques, especially the isotopic dilution method, are also discussed. Conclusions and future perspectives are outlined.     

Development of human serum certified reference material for quantification of polychlorinated biphenyls

Human serum certified reference material (CRM), NMIJ CRM 7407-a, for the analysis of polychlorinated biphenyls (PCBs) was developed by the National Metrology Institute of Japan. A pool of commercially available human serum was used as a raw material of the CRM. This sample is in the form of a liquid comprising approximately 4 g stored in a cryogenic polypropylene vial. Homogeneity assessment was performed, and the material was homogeneous enough for PCB 118, PCB 138, PCB 153, and PCB 194: the relative uncertainties due to inhomogeneity were 2.5–10.5%. The results obtained from the stability assessment indicated that the target PCBs were stable: the relative uncertainties due to instability were 0–14.7%. The certification was carried out using two different types of GC columns for each target PCB to avoid interferences on GC separation; the certified values of the target PCBs (PCB 118, PCB 138, PCB 153, and PCB 194) were 9.7–129.8 ng/kg. This is the first frozen human serum CRM in which PCBs were determined by isotope dilution mass spectrometry.     

Gas chromatographic separation of polychlorinated biphenyls on a new apolar capillary column

Eighty one polychlorinated biphenyls (PCBs) and nineteen chlorinated pesticide standards have been analyzed on a newly developed apolar high resolution gas chromatography (HRGC) column. Emphasis was placed on the determination of PCB indicator congeners which are part of national regulations, and of toxic coplanar PCB congeners. The new column enables almost unambiguous quantification of the PCB indicator congeners (PCB 138 can be separated from both PCB 163 and PCB 164; PCB 28 and PCB 31 were also separated and no coelution was observed for PCB 52, PCB 118, and PCB 180). The new column furnished better results than CP-Sil 8 for the analysis of PCB indicator congeners in a sample of seal blubber.     

Ultrasound‐assisted magnetic SPE based on Fe3O4‐grafted graphene for the determination of polychlorinated biphenyls in water samples

An ultrasound‐assisted magnetic SPE procedure with an Fe₃O₄‐grafted graphene nanocomposite as the magnetic adsorbent has been developed to determine seven polychlorinated biphenyls (PCBs; PCB28, PCB52, PCB101, PCB118, PCB138, PCB153, and PCB180) simultaneously in 200 mL environmental water samples, in combination with GC–MS/MS. Several factors related to magnetic SPE efficiencies, such as the superparamagnetic intensity and amount of adsorbent, extraction time, sample pH, and desorption conditions were investigated. With the assistance of ultrasound, the extraction achieved the maximum within only 20 s, attributed to the powerful adsorptive ability of the magnetic adsorbent toward the PCBs. Under the optimized conditions, an excellent linearity was observed in the range of 0.1–100 ng/L for PCB28, 0.2–100 ng/L for PCB52, and 0.5–100 ng/L for the other five PCBs with the correlation coefficients ranging from 0.9988 to 0.9996. The mean recoveries at spiked levels of 5.0 and 10.0 ng/L were 84.9–108.5%, the coefficients of variations were <6.5%. With convenient magnetic separation, the synthesized magnetic adsorbent could be recycled more than ten times. The proposed method was demonstrated to be feasible, simple, rapid, and easy to operate for the trace analysis of the PCBs in environmental water samples.     

两相溶剂萃取黄连木籽油制备生物柴油

以黄连木籽为原料,采用乙醇/异己烷两相不互溶溶剂对其进行萃取处理.考察了乙醇／异己烷体积比、萃取温度和萃取时间对萃取过程的影响.通过实验确定最佳的萃取条件为,黄连木仁粉50 g,乙醇异己烷总体积300 mL,乙醇/异己烷体积比为50∶50,萃取温度40℃,萃取时间30 min.在此条件下,黄连木籽油出油率达到99.5％...