TiO_2/SBA-15的快速合成法及其催化性能

本文针对传统方法合成TiO2/SBA-15的诸多不足,提出了一种简单而快速合成TiO2/SBA-15的方法。利用孔道内水解法快速合成了不同负载量的TiO2/SBA-15。利用XRD、N2-吸脱附、TEM和UV-Vis对样品的晶体结构、微观形貌、光学吸收特性进行了表征,并研究了不同TiO2负载量催化剂对罗丹明B(RhB)光降解活性的影响。结果表明:利用该方法合成的TiO2/SBA-15光催化活性优于传统浸渍方法合成的TiO2/SBA-15与工业上使用的TiO2纳米颗粒。     

锐钛矿型纳米TiO2介孔粉体表面织构的研究

以硫酸钛和尿素为原料,聚乙二醇-1000为空间构造剂,104℃下经尿素水解均匀沉淀法研制颗粒分散均匀、粒径可控的高热稳定性锐钛矿型纳米TiO2介孔粉体,并对其晶相、颗粒大小、比表面积、形貌和孔道结构进行了表征.结果表明,未经任何热处理的TiO2粉体即为锐钛型晶相,颗粒为均匀分散的类球型颗粒,且颗粒间形成直通型的介孔孔道,其孔径在10～30nm之间.控制焙烧温度可以达到控制颗粒大小及形貌的目的,经850℃焙烧5h的样品仍保持锐钛矿型晶相,未出现向金红石型晶相转变的迹象.     

高分散TiO_2/SBA-15的制备及光催化性能

提出了一种制备高分散TiO2/SBA-15光催化剂的新方法.以钛酸四正丁酯(TB)和羧基改性的SBA-15(COOH/SBA-15)为原料,利用COOH/SBA-15表面上高分散的羧基与TB的配合作用将TB锚定,经过溶剂热及焙烧处理制得TiO2/SBA-15光催化剂.采用粉末X射线衍射(XRD),N2吸脱附,傅里叶变换红外光谱(FT-IR),透射电镜(TEM)等对所得催化剂进行了表征.结果表明:所得TiO2/SBA-15光催化剂为高结晶度的锐钛矿晶型,TiO2均匀地分散在SBA-15表面,TiO2/SBA-15光催化剂保持较好的介孔特征结构,具有较大比表面积.以降解罗丹明B(RhB)为探针反应,考察了所得TiO2/SBA-15光催化剂的光催化性能.与后处理浸渍法制备的光催化剂相比,本文制备的TiO2/SBA-15光催化剂表现出了更加优越的光催化性能.     

一种新的高活性CO氧化催化剂Ag/SBA-1

 以SBA-15为载体,采用后修饰法制备了Ag/SBA-15催化剂. XRD和TEM结果表明,金属Ag粒子均匀分散于SBA-15的纳米孔道中,粒子平均大小为4～5 nm. 同时,负载金属Ag纳米粒子后,载体的介孔结构仍然能很好地保持. CO催化氧化测试结果表明,Ag/SBA-15具有很高的催化活性,120 ℃时就能使CO完全氧化. 而在富H2气氛下,80 ℃时CO的转化率达到最大值(48%),此时O2的选择性为28%. 高温H2还原是活化Ag/SBA-15的必要步骤.     

一步法直接合成有机季铵功能修饰的介孔分子筛SBA-15

以P123 嵌段共聚物为模板剂, 3-三甲基丙基氯化铵三甲氧基硅烷(TMAPS)为修饰剂, 酸性条件下一步法直接合成了有机季铵基团功能修饰的SBA-15, 并通过XRD、TEM、N2吸附-脱附、Raman 光谱等对功能化样品的结构和性质进行了表征, 对一步法合成TMAPS 修饰的SBA-15 的可能反应机理进行了探讨. 修饰后的SBA-15 仍然保持了二维六方特征介孔结构, 随着TMAPS负载量的增大, SBA-15 孔道有序度下降, 孔径、孔容和比表面积也随之下降. 有机季铵基团在SBA-15 孔道表面均匀分散, 可与HAuCl4通过快速离子交换制备Au 颗粒高度分散的Au-SBA-15.     

SBA-15固载磷钨酸催化剂的制备及催化性能

以SBA-15和氨基功能改性的SBA-15／NH2为载体,采用浸渍法制备了固载磷钨酸催化剂,通过FT—IR光谱,Raman光谱,XRD衍射分析,N2-吸附脱附实验,TEM和NH3-TPD等手段对催化剂进行表征．结果表明,磷钨酸在两种载体上均保持Keggin结构,载体的介孔结构没有明显破坏．在高固载量情况下,磷钨酸在SBA-15载体上发生晶相聚集,介孔孔道发生堵塞使比表面积、孔容和孔径明显减小．在SBA-15／NH2载体上,磷钨酸与载体发生酸碱作用,能够均匀分散于SBA-15／NH2的孔道中,但催化剂酸性有所降低．考察了相同固载量的两种催化剂对苹果酯合成反应的催化活性,结果表明,以SBA-15／NH2为载体的催化剂具有良好的重复使用性能．     

Ag/SBA-15低温气相选择性催化氧化苯甲醇合成苯甲醛（英文）

以SBA-15为载体,采用浸渍法制备了不同Ag含量的Ag/SBA-15,通过N2吸附-脱附、X射线衍射、扫描电子显微镜、高分辨透射电子显微镜、X射线光电子能谱和电感耦合等离子体质谱对催化剂进行了表征.将Ag/SBA-15用于苯甲醇气相选择性催化氧化合成苯甲醛,研究了反应条件对转化率和选择性的影响.结果表明,Ag/SBA-15具有均一的一维孔道结构、较厚的孔壁(3–5 nm)及较大的比表面积(411–541 m2/g),其规整纳米空间的限域作用使一定负载量的Ag以纳米尺寸均匀分散于介孔SBA-15孔道内,增加了活性组分的比表面积.亲核性氧物种从Ag到SBA-15表面的氧溢流,提高了低温下Ag/SBA-15对苯甲醇气相选择性氧化合成苯甲醛的催化性能.5.3%Ag/SBA-15中的Ag粒径为5–6 nm,且均匀分散于载体孔道中,反应温度为220°C时,苯甲醇转化率为87%,苯甲醛选择性为95%;240°C时,苯甲醇转化率和苯甲醛选择性分别高达94%和97%;并在240–300°C范围内,其催化活性和选择性保持不变,表现出了良好的温度耐受能力.催化剂经活化再生可以连续使用40 h,选择性基本保持不变.     

SBA-15负载高分散纳米NiO的丙烷氧化脱氢制丙烯催化性能

采用浸渍法通过改变焙烧气氛制备了系列NiO/SBA-15 (w_NiO=20%)催化剂, 并考察了催化剂的丙烷氧化脱氢(ODHP)反应性能. 实验结果表明, 与在静止和流动空气中焙烧的催化剂相比, 在1%NO/He (V_NO/V_He=1:99)气氛中焙烧的NiO/SBA-15-NO具有优异的低温丙烷氧化脱氢制丙烯性能, 在350 ℃时, 丙烷的转化率和丙烯收率分别约达29%和13%. 反应温度升至450 ℃时, 丙烯的选择性仍保持在45%左右. X射线粉末衍射(XRD)和透射电镜(TEM)测试结果表明, 1%NO/He气氛可有效抑制焙烧过程中NiO纳米颗粒的团聚, 使NiO物种高分散于SBA-15 的孔道中. H₂-程序升温还原(H₂-TPR)和O₂-程序升温脱附(O₂-TPD)测试结果表明, 随着NiO在SBA-15上分散度的提高, 催化剂的抗还原性增强, ODHP活性氧物种O-的含量增加, 进而使1%NO/He气氛中焙烧的NiO/SBA-15-NO在较宽的温度范围内(350-450 ℃)均具有良好的丙烯选择性, 并显著提高了催化剂的低温活性.     

Au/SBA-15 的制备及其催化 CO 氧化反应性能

 以 SBA-15 为载体, 采用沉积沉淀法制备了纳米 Au 催化剂, 研究了不同预处理条件对 Au 在载体表面状态的影响, 考察了催化剂样品催化 CO 氧化性能. 以高分辨率透射电子显微镜、N2 吸附、X 射线衍射、紫外-可见漫反射吸收谱、X 射线光电子能谱和电感耦合等离子体发射光谱等手段对催化剂的结构和表面性质进行了表征. 结果表明, 经还原焙烧处理后的 Au/SBA-15 催化剂热稳定性较好, Au 在 SBA-15 孔道表面呈高分散状态, 样品在 CO 氧化反应中表现出优异的低温催化活性和高温稳定性, 同时具有优异的抗烧结性能和良好的循环稳定性.     

Co-B/SBA-15非晶态催化剂应用于肉桂醛选择性加氢的研究

以介孔材料SBA-15作为载体,采用浸渍法制备Co-B/SBA-15非晶态催化剂,该样品仍然保持SBA-15特有的有序规整孔道结构,Co-B非晶态合金颗粒均匀分布在孔道内壁,采用普通SiO2载体制备的Co-B/ SiO2,Co-B颗粒主要分布在外表面.在肉桂醛选择性加氢制肉桂醇中,Co-B/SBA-15的催化活性和对肉桂醇的最佳得率显著高于Co-B/SiO2,主要归因于活性位的高分散,规整的孔道结构,以及独特的活性位团簇结构和电子态.     

Characterization of vanadium and titanium oxide supported SBA-15

Supported vanadium and titanium oxide catalysts were prepared by adsorption and subsequent calcination of the vanadyl and titanyl acetylacetonate complexes, respectively, on mesoporous SBA-15 by the molecular designed dispersion (MDD) method. Liquid and gas phase depositions at different temperatures were carried out with vanadyl acetylacetonate, and the different results together with those of titanyl acetylacetonate in the liquid phase deposition were discussed. The bonding mechanism, the influence of the metal interaction with the support material, and differences due to the way of deposition and the temperature were investigated by TGA, chemical analysis, FTIR, and Raman spectroscopy. Elevated dissolving temperatures in the liquid phase led to higher final loadings on the SBA-15 without the formation of clusters, even at high loadings. The decomposition of the anchored vanadium and titanium complexes, their thermal stability, and the conversion to the covalently bound VO(x) and TiO(x) species on SBA-15 were studied and investigated by in situ transmission IR spectroscopy. In general, the titanium complex is more reactive than the vanadium complex toward the surface of SBA-15 and has a higher thermal stability. The MDD method of the VO(acac)2 and TiO(acac)2 enables to create a dispersed surface of supported VO(x) and TiO(x), respectively. The structure configurations of VO(x) and TiO(x) oxide catalysts obtained at different metal loadings were studied by Raman spectroscopy. Pore size distributions, XRD, and N2 sorption confirmed the structural stability of these materials after grafting. VO(x)/SBA-15 and TiO(x)/SBA-15 samples, with different metal loadings, were also catalytically tested for the selective catalytic reduction (SCR) of NO with ammonia.     

The Promoting Effect on the Activities of Fe Doped TiO2 Photocatalysts

IntroductionPhotocatalytic techno1ogy used for water, air, and wastewater treatments has been anarea having a rapidly growing interest to many researchers since Fujishima and Honda foundthe photo-electricity catalytic degradation effect of water at a n-semiconductor TiO2 electrodein 1972[1--6J. It has been proved that TiO2 is a benchmark semiconductor for the effectivedegradation of organic polutants['J. The production of the electron-hole pairs of photo-excita-tion and their transfer to ch…     

A comparative study of CuO/TiO_2-SnO_2,Cut/Tit_2 and CuO/SnO_2 catalysts for low-temperature CO oxidation

Nanometer SnO2 particles were synthesized by sol-gel dialytic processes and used as a support to prepare CuO supported catalysts via a deposition-precipitation method. The samples were characterized by means of TG-DTA, XRD, H2-TPR and XPS. The catalytic activity of the CuO/TiO2-SnO2 catalysts was markedly depended on the loading of CuO, and the optimum CuO loading was 8 wt.% (T100 = 80 ◦C). The CuO/TiO2-SnO2 catalysts exhibited much higher catalytic activity than the CuO/TiO2 and CuO/SnO2 catalysts. H2-TPR result indicated that a large amount of CuO formed the active site for CO oxidation in 8 wt.% CuO/TiO2-SnO2 catalyst.     

Dynamic electronic structure of a Au/TiO2 catalyst under reaction conditions

The electronic structure of a highly active Au/TiO2 powder catalyst was probed in situ by synchrotron X-ray photoelectron spectroscopy (XPS) in the 10-1 mbar range. The electronic structure of the Au component was found to respond sensitively to changes in temperature and indicated the absence of bulklike metallic Au under the conditions of highest catalytic activity. Concurrent modification of interfacial sites adjacent to Au on the TiO2 support was not evident from the Ti photoemission, but may have been below the detection limit of XPS.     

Controlled synthesis, characterization, and catalytic properties of Mn(2)O(3) and Mn(3)O(4) nanoparticles supported on mesoporous silica SBA-15

A method established in the present study has proven to be effective in the synthesis of Mn(2)O(3) nanocrystals by the thermolysis of manganese(III) acetyl acetonate ([CH(3)COCH=C(O)CH(3)](3)-Mn) and Mn(3)O(4) nanocrystals by the thermolysis of manganese(II) acetyl acetonate ([CH(3)COCH=C(O)-CH(3)](2)Mn) on a mesoporous silica, SBA-15. In particular, Mn(2)O(3) nanocrystals are the first to be reported to be synthesized on SBA-15. The structure, texture, and electronic properties of nanocomposites were studied using various characterization techniques such as N2 physisorption, X-ray diffraction (XRD), laser Raman spectroscopy (LRS), temperature-programmed reduction (TPR), transmission electron microscopy (TEM), and X-ray photoelectron spectroscopy (XPS). The results of powder XRD at low angles show that the framework of SBA-15 remains unaffected after generation of the manganese oxide (MnO(x)) nanoparticles, whereas the pore volume and the surface area of SBA-15 dramatically decreased as indicated by N2 adsorption-desorption. TEM images reveal that the pores of SBA-15 are progressively blocked with MnO(x) nanoparticles. The formation of the hausmannite Mn(3)O(4) and bixbyite Mn(2)O(3) structures was clearly confirmed by XRD. The surface structures of MnO(x) were also determined by LRS, XPS, and TPR. The crystalline phases of MnO(x) were identified by LRS with corresponding out-of-plane bending and symmetric stretching vibrations of bridging oxygen species (M-O-M) of both MnO(x) nanoparticles and bulk MnO(x). We also observed the terminal Mn=O bonds corresponding to vibrations at 940 and 974 cm-1 for Mn(3)O(4)/SBA-15 and Mn(2)O(3)/SBA-15, respectively. These results show that the MnO(x) species to be highly dispersed inside the channels of SBA-15. The nanostructure of the particles was further identified by the TPR profiles. Furthermore, the chemical states of the surface manganese (Mn) determined by XPS agreed well with the findings of LRS and XRD. These results suggest that the method developed in the present study resulted in the production of MnO(x) nanoparticles on mesoporous silica SBA-15 by controlling the crystalline phases precisely. The thus-prepared nanocomposites of MnO(x) showed significant catalytic activity toward CO oxidation below 523 K. In particular, the MnO(x) prepared from manganese acetyl acetonate showed a higher catalytic reactivity than that prepared from Mn(NO(3))2.     

镧助剂对模拟生物沼气重整制备合成气中Ni/SBA-15催化剂结构和性能的影响

以介孔分子筛SBA-15为载体, 采用浸渍法制备了镍质量分数(w)为12.5%, 并且分别添加质量分数(w)为2.5%的镧、铈、镁、钙、锶等助剂的系列Ni基催化剂. 以CH4/CO2体积比为2:1的模拟生物沼气和适量氧气作为原料气, 在常压固定床反应器上评价了催化剂对模拟生物沼气重整制合成气的反应性能. 采用X射线粉末衍射(XRD)、N2吸附/脱附、透射电子显微镜(TEM)、X射线光电子能谱(XPS)及H2程序升温还原(H2-TPR)等对催化剂的结构进行了表征. 催化活性评价显示, 添加镧助剂的2.5%La/12.5%Ni/SBA-15催化剂比添加铈、镁、钙、锶等助剂的催化剂具有更高的催化活性, 并且具有很好的稳定性. 因此, 文中着重研究了镧助剂对催化剂结构和模拟生物沼气重整制合成气的反应性能的影响. 结果表明, 镧能明显提高Ni/SBA-15催化剂的表面镍含量, 同时还具有很好的抗积炭作用, 在850 ℃的温度下反应820 h没有发现积炭生成, 这些可能是提高催化剂性能和稳定性的重要因素.     

Controlled synthesis of highly dispersed TiO2 nanoparticles using SBA-15 as hard template

Highly dispersed TiO2 nanoparticles were successfully synthesized by a wet impregnation method using SBA-15 as hard template for confining the growth of TiO2 nanocrystals, and then calcined at 550 degrees C in muffle furnace for 2 h. The as-synthesized samples were characterized with Fourier transform infrared spectra (FTIR), Raman spectroscopy, diffuse reflectance UV-visible spectroscopy (UV-vis), powder X-ray diffraction (XRD), small-angle X-ray diffraction (SAXRD), nitrogen adsorption, transmission electron microscopy (TEM) and photoluminescence spectra (PL). It was found that SBA-15 contained abundant silanol groups after removal of triblock copolymers by ethanol extraction and could easily adsorb a great number of titanium alkoxide via chemisorption. After subsequent hydrolysis of the anchored Ti complexes and calcination of the amorphous TiO2, anatase TiO2 nanocrystals with spherical shape and uniform particle diameter of about 6 nm were formed. A blue shift was observed in UV-vis absorption spectra due to the quantum size effect of TiO2 nanoparticles. Moreover, the as-prepared TiO2 nanoparticles showed a high PL intensity due to an increase in the recombination rate of photogenerated electrons and holes under UV light irradiation.     

Metallic nickel supported on mesoporous silica as catalyst for hydrodeoxygenation: effect of pore size and structure

Catalytic hydrodeoxygenation (HDO) of anisole, a methoxy-rich lignin-derived bio-oil model compound, was carried out over a series of Ni-containing (5, 10, 20, and 30 wt%) catalysts with commercial silica and ordered mesoporous silica SBA-15 as support. Both supports and catalysts were characterized by N₂ adsorption–desorption isotherms, X-ray diffraction, CO chemisorption, and transmission electron microscopy (TEM). Catalytic reaction was performed at 250 °C and 10 bar H₂ pressure. Depending on the catalyst support used and the content of active metal, the catalytic activity and product distribution changed drastically. Increase of the nickel loading resulted in increased anisole conversion and C₆ hydrocarbon (benzene and cyclohexane) yield. However, loading more Ni than 20 wt% resulted in a decrease of both conversion and C₆ yield due to agglomeration of Ni particles. In addition, Ni/SBA-15 samples exhibited much stronger catalytic activity and selectivity toward C₆ hydrocarbon products compared with Ni/silica catalysts. The differences in catalytic activity among these catalysts can be attributed to the effect of the pore size and pore structure of mesoporous SBA-15. SBA-15 can accommodate more Ni species inside channels than conventional silica due to its high pore volume with uniform pore structure, leading to high HDO catalytic activity.     

粉末化学镀法制备的NiB／TiO2非晶态合金催化剂对环丁烯砜加氢反应的催化性能

 采用诱导沉积法及粉末化学镀法分别制备了纯态NiB及负载型NiB／TiO2非晶态合金催化剂．用XRD，ICP，SEM，TEM和DSC等手段对催化剂的物性及TiO2载体与NiB非晶态合金之间的相互作用进行了表征，考察了非晶态合金的结构、组成、形貌和热稳定性，并将其用于环丁烯砜加氢反应中．结果表明，相对于NiB而言，NiB／TiO2催化剂具有优良的热稳定性和催化活性，这缘于NiB和TiO2载体之间的相互作用及载体的分散作用．