硅胶自环己烷中吸附含氧芳香化合物的研究

测定了15℃和30℃时硅胶自环己烷中吸附苯甲醇、苯甲醚、苯甲醛和苯甲酸的吸附等温线,这些等温线皆可用Langmuir公式表示。利用Langmuir常数n_m^s和b值计算了吸附过程的△G⁰、△H⁰和△S⁰;四种化合物的△S⁰皆为正值。测定了在较大复盖度时红外光谱图上硅胶表面自由羟基峰的移动值△v_OH。结果表明△H⁰和△v_OH及△v_OH^1/2间有线性关系。文中对所得结果做了初步的解释。     

吸附法研究固体表面的分形性质

介绍用气体和蒸气吸附等温线数据求出的单层饱和吸附量和根据等温线毛细凝结区域数据求算分形固体表面分维值的方法;提出了用固体自溶液中吸附数据计算分维值的方法。讨论了介孔吸附剂的分维和固体表面分形性质在物理化学方面的应用。     

介孔硅胶在柴油氧化-吸附组合脱硫中的应用研究

以硅胶(SG)为吸附剂,采用自制的双亲催化剂与H₂O₂组成的催化氧化体系将柴油进行氧化,利用固定床动态吸附法考察了硅胶性质、氧化过程及吸附条件等对硅胶吸附脱硫性能的影响,并对硅胶进行了表征。小角XRD和氮气吸脱附结果表明,实验所用硅胶具有介孔结构。吸附脱硫实验结果表明,在油剂比(柴油与吸附剂的体积比)相同时,氧化-吸附脱硫过程脱硫率明显高于吸附脱硫过程脱硫率;选用硅胶作吸附剂,吸附温度为40℃,吸附空速为6.0 h^-1时脱硫效果较好,当油剂比为1时,脱硫率高达94.57%,且该介孔硅胶具有较大的吸附硫容,随油剂比增大下降缓慢,当油剂比增大到15时,脱硫率仍达85.89%。     

介孔TiO2对溶菌酶吸附的动力学和热力学

773.15 K下焙烧二钛酸(H₂Ti₂0₅)制备了介孔结构TiO₂。采用比表面分析仪(BET)、扫描电镜(SEM)、拉曼(Raman)光谱和X射线衍射(XRD)仪进行表征研究了介孔TiO₂对溶菌酶的吸附行为和机理。结果表明,该吸附过程较好地满足Langmuir吸附模型;随着溶液pH值的增高,溶菌酶在介孔TiO₂上的吸附量先增大后减小。在pH = 7.2时,达到最大吸附容量72.5 mg·g^-1。该介孔TiO₂对溶菌酶具有良好的吸附稳定性,经过5次循环后吸附的溶菌酶残余量仍有81.6%。动力学研究表明,介孔TiO₂与溶菌酶间的吸附满足准二级动力学模型,吸附传质过程由膜扩散和粒内扩散共同影响与控制。对热力学参数的计算发现,该过程ΔG⁰ < 0, ΔH⁰ > 0, ΔS⁰ > 0,表明介孔TiO₂对溶菌酶的吸附是一个自发的、吸热的熵增过程。     

萘在介孔分子筛MCM-41与SBA-15上的吸附特性研究

对低浓度气相萘在两种常见介孔分子筛MCM-41和SBA-15上的吸附特性进行研究。得到了萘在两种吸附剂上的吸附等温线和不同初始浓度下的穿透曲线,并分别与吸附等温线模型(Langmuir、Freundlich、D-R)和恒定浓度波动力学模型进行了拟合。结果表明, Langmuir模型能很好描述低浓度气相萘的吸附等温线(R²均在99%以上);具有微孔结构的SBA-15对萘的吸附能力要优于仅具备介孔结构的MCM-41。动力学模型在初始浓度较低时能较好地预测萘在吸附剂上的穿透曲线,且在SBA-15上的相关系数高于MCM-41;萘在2.76 mol/L时具有较大介孔的SBA-15的总传质系数K_a更高,表明萘在SBA-15上的总传质阻力更低,更能较快达到传质平衡。     

苯并噻吩在酸改性NaY分子筛上的吸附

以NaY分子筛为母体,通过柠檬酸、磷酸改性分别得到吸附剂NaY-C和NaY-P.采用SEM、XRD、XRF、N₂物理吸附及NH₃-TPD表征可知,柠檬酸改性后得到的NaY-C吸附剂介孔表面积增加,分子筛骨架结构保持不变.同时,磷酸改性使得NaY分子筛表面弱酸量减少强酸量增加,改性后所得吸附剂NaY-P的强酸量大于NaY-C.吸附实验表明,NaY-C和NaY-P均可完全脱除模拟油品中的苯并噻吩,同时NaY-C吸附剂对0^#柴油的脱硫能力优于NaY-P吸附剂.再生实验中NaY-C和NaY-P吸附剂对模拟油品的脱硫率由第一次的100%分别下降至第6次的91.97%和85.96%.由此可知,柠檬酸改性NaY分子筛所得NaY-C吸附剂的脱硫能力优于NaY-P,原因是吸附剂上的介孔更易于发生吸附脱硫.     

分子连接性指数与溶液吸附自由能的相关性

测定了硅胶自四氯化碳中吸附脂肪醇及活性炭自水中吸附芳香化合物的吸附等温线, 等温线均可用Langmuir方程描述。利用Langmuir参数计算了各体系的吸附标准自由能变化。计算了各种吸附质的分子连接性指数。各种分子的分子连接性指数与吸附标准自由能变化间有相关性, 并给出了相关方程, 同时作了初步的讨论。     

改性柏树锯末对铜离子吸附机制研究

本文以KMnO₄改性处理的柏树锯末为吸附剂,对溶液中的Cu²⁺吸附去除。结果表明,改性锯末增大了孔径和比表面积,吸附剂表明吸附位点增多,当pH=7、吸附剂用量1 g·L^-1及温度318 K的条件下吸附效果最佳。改性柏树锯末对Cu²⁺的吸附动力学和等温线线性拟合结果分别符合准二级动力学方程和Langmuir吸附等温模型,说明该吸附过程是单分子层吸附,并以化学吸附为主。     

新型功能介孔吸附剂NiNb_2O_6的合成及其吸附性能研究

通过柠檬酸溶胶-凝胶反应,合成了新型功能介孔NiNb2O6吸附剂,通过X-射线粉末衍射仪(XRD)、透射电镜(TEM)和比表面积及孔径分析(BET)对其结构进行表征。通过影响因素实验、吸附动力学实验和等温吸附实验,探讨了NiNb2O6吸附剂对水溶液中亚甲基蓝的吸附性能和机理。结果表明,NiNb2O6介孔吸附剂具有正交相晶体结构,平均粒径为30~200nm,比表面积为66.3m2/g。吸附剂用量、温度和pH值均对吸附行为有一定的影响;在35℃时,亚甲基蓝在吸附剂上吸附行为符合Langmuir方程,吸附动力学符合拟二级动力学方程,初始浓度为40mg/L,pH值为7.03时,0.2g介孔吸附剂NiNb2O6对亚甲基蓝的吸附量最大,吸附过程中液膜扩散为主要速率控制步骤。     

污泥活性炭的结构特征及表面分形分析

以城市污水厂污泥为主要原料添加适量添加剂, 采用ZnCl₂化学活化法制备的污泥活性炭, 借助XRD, BET法, FT-IR, SEM等现代分析测试方法结合液相吸附法, 表征结构特征和分析表面分形维数. 结果表明: 在适宜的活化温度、活化时间、ZnCl₂浓度、原料粒度等工艺条件下, 加入少量添加剂制备的污泥活性炭, 最可几孔径分布在4.16 nm左右,平均孔容0.4484～0.5122 mL•g^－1, 比表面积为634.8～748 m²•g^－1, IR峰中出现C—OH, C—H, N＝O, C＝C功能组, 孔结构是具有平行壁的狭缝状介孔结构. 由液相吸附法得到的污泥活性炭分维近似为2, 属于低分维二维表面.     

Application of Fractal Theory in Evaluating Geological Structure Complexity of Nanwu Section in Tangshan Mine

利用分形理论对唐山矿南五区的断裂网络复杂程度进行了评价,即所算得的分维数越高,则构造越复杂,对矿井的安全生产影响就会增大。研究表明：从5#煤层至9#煤层,断裂迹线分布程度从集中到相对分散;构造复杂区主要位于区域北部及南偏东位置,而该区中部偏东位置和西南角的构造简单,相对稳定。     

Structures and their influence factors of three‐dimensional fractal cadmium layer formed by electrodeposition

Three‐dimensional fractal structure of the electrodeposited cadmium layer was investigated. The results suggested that the fractal growth begin with nanometer scale aggregate within which the atoms arrange in hexagonal close‐packed lattice (the normal cadmium lattice). The fractal structure is correlated to the current density. The higher the current density is, the larger the size of fractal growth will be. Fractal structures can emerge in both the complete diffusion‐limited process and the combination‐limited process of the electrochemical reaction and diffusion. The fractal structure obtained from the simple hydrated ion electrolyte is different from that obtained from the complex ion electrolyte, which indicates they grow in different modes. The fractal dimensionality of deposit from the simple hydrated ion electrolyte is 2.592, smaller than that (2.608) from the complex ion electrolyte.     

Numerical computations of molecular reactions in associated systems caused by the formation of fractal structures

The interaction between particles in a system containing fractal clusters has been computationally simulated. The fractal structure of the system has been demonstrated to determine the kinetic characteristics of particle interaction. If a system in an N-dimensional space (N = 2, 3, 4) contains fractal clusters with the fractal dimension D > N-1, the rate of interaction of a free particle with particles belonging to clusters depends on their concentration according to the power law. The exponent gamma of this power law formally corresponds to the kinetic order of the reaction with respect to the concentration of particles belonging to the clusters. Its value is determined by the free surface of the clusters and depends on its fractal dimension D. The results of simulation qualitatively agree with the data on high, non-integral orders of many liquid phase molecular reactions characterized by self-organization of the medium via weak intermolecular interactions, such as hydrogen bonds.     

金属线电极分形生长的模拟

电沉积金属过程中,阴极沉积的金属边缘会出现包括枝晶生长在内的许多复杂形态,这会严重影响电沉积产品的质量和加工过程中的电流效率. 对枝晶分形生长的过程以及形貌进行研究,可以实现对沉淀物的可控生长. 本研究使用Python和Matlab软件相互结合,基于扩散限制凝聚（DLA）模型,建立平行线电极电沉积的模型. 通过分析不同粒子数、沉积概率、电极间距、运动步长、定向漂移条件下的分形生长的变化规律,以及模拟参数与实际电沉积因素对分形生长影响的内在联系,发现只要合理控制模拟的粒子数、沉积概率、线电极间距、运动步长、定向漂移概率参数即可与实际电化学体系的浓度和沉积时间、还原概率、两极间距、温度和电压、电极的相对位置和形状一一对应,从而模拟得到跟实际电沉积接近的分形图,最终可实现对分形生长的可控操作,对分形生长在工业电沉积等方面应用有很大的意义.     

催化剂表面分形结构对催化反应的影响

用溶胶－凝胶方法制备了ＳｉＯ２并以其及另一种ＳｉＯ２气凝胶作载体,用浸渍法制备了两种铑基催化剂。以ｎ－Ｃ５～Ｃ８烷烃为探针分子,测得两种催化剂的表面分形维数Ｄ分别为３和２。在两种催化剂上,ＣＯ加氢和丙烷氢解反应的选择性没有显著差别,但在Ｄ＝２的催化剂上,ＣＯ加氢和丙烷氢解反应的速度显著高于Ｄ＝３的催化剂     

The Evolution of Microstructure in Nonhydrolytic Alumina Xerogels

The effect of drying, aging and thermal treatment of alumina xerogels prepared by the nonhydrolytic route was investigated using SAXS, BET and HR-SEM techniques. The microstructure of the fresh xerogels prepared under different procedures varied drastically, ranging from aerogel-like mass fractals to narrow pore size distribution materials. By variation of the drying conditions the N2-BET surface area was varied from an immeasurable low level up to 600 m2/g. The initial microstructure has a significant influence on the xerogel behaviour during the post-drying heating stage. The ability to produce aerogel-like mass fractal materials from the nonhydrolytic systems is discussed. Finally, a brief theoretical treatment of the drying process of mass fractals is presented as well.     

Fractal notation for nearly-symmetrical dendrimers

Dendrimeric and related molecules that have the same atomic connectivity from exterior to core, P-C₁-J₁-C₂- … Z (P peripheral group, J juncture, C connector, Z core) can be described completely by a highly compact fractal notation, which is of the general form Pf _{J1,J2 …} (C₁.C₂ …)Z. In this paper, we show how to describe molecules that deviate slightly from the symmetry of a related parent molecule, by use of parenthetic expressions (iX), (dX), and (YrX) which designate atoms or molecular groups that are inserted, deleted, or replaced by other groups in the parent. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 2979–2983, 1998     

Elastic properties of networks of fractal clusters

Elastic properties of casein gels were followed by dynamic measurements for various volume fractions of casein micelles far above the percolation threshold. Elastic and loss storage moduli versus volume fractions obey a power law with an exponent close to 3. The previous theoretical models for networks made of a homogeneous packing of fractal flocs do not predict the observed behavior. A model is proposed to estimate the vectorial contribution to the network elasticity. This model is in agreement with our experimental results. The value of the fractal dimension of the flocs derived from this analysis is discussed as a function of the volume fraction of primary particles.     

复合粒子涂膜表面疏水性能分形评价

采用接枝法和非均相乳液聚合与溶胶-凝胶法相结合技术,制备了不同形状的复合粒子,经低表面能的物质修饰后,其涂膜表面具有超疏水性。采用分形理论对涂膜表面疏水性进行评价,用分形维数表征涂膜表面微观形貌与疏水性能之间的关系,结果表明对于粗糙结构表面,分形维数较粗糙度因子能更好地反映表面形貌对水接触角的影响。     

Kinetics on Diffusion-Controlled Reactions in a Fractal Medium

The kinetics are investigated for diffusion-controlled reactions in a fractal medium described by a Smoluchowski equation. A class of model potentials are taken into account so as to solve the time-dependent Smoluchowski equation. Corrections to the standard solution are proposed for the fractal geometry of the medium.