吡唑基镁卤化物/四氢呋喃可充镁电池电解液

将不同配比的吡唑与格氏试剂反应制得的吡唑基镁卤化物/四氢呋喃（THF）溶液用作可充镁电池电解液,采用循环伏安和恒电流充放电测试研究了该电解液的镁沉积-溶出性能和氧化分解电位;并通过X射线衍射（XRD）和扫描电镜（SEM）对沉积物的组分和形貌进行了分析. 结果表明,吡唑上的取代基、吡唑与格氏试剂的反应配比对电解液的电化学性能都有影响. 1 mol·L^-1 1-甲基吡唑-PhMgCl（1：1摩尔比）/THF反应配制的电解液在不锈钢（SS）集流体的阳极氧化分解电位达到2.4 V（vs Mg/Mg²⁺）,并具有镁沉积-溶出电位低、循环稳定性高、配制方便的特点,有希望应用于实际的可充镁电池体系中.     

PP14TFSI离子液体在可充镁电池电解液的应用

制备了可充镁电池电解质苯酚基镁盐,以四氢呋喃（THF）与N-甲基-N-丁基-哌啶-双三氟甲基磺酰胺（PP14TFSI）离子液体混合物代替四氢呋喃作为该电解质的溶剂. 当THF与PP₁₄TFSI体积配比为1:1时,该苯酚基镁盐电解液镁可逆溶出性能最佳,电化学窗口宽（2.7 V vs. Mg）,离子电导率高（7.77 mS·cm^-1）. 此外,热重测试表明离子液体的加入大大降低了THF溶剂的挥发性,提高了可充镁电池的安全性能. 四氢呋喃 + N-甲基-N-丁基-哌啶-双三氟甲基磺酰胺混合溶剂有望作为可充镁电池电解液的首选溶剂.     

吡唑基镁卤化物/四氢呋喃可充镁电池电解液

将不同配比的吡唑与格氏试剂反应制得的吡唑基镁卤化物/四氢呋喃(THF)溶液用作可充镁电池电解液,采用循环伏安和恒电流充放电测试研究了该电解液的镁沉积-溶出性能和氧化分解电位;并通过X射线衍射(XRD)和扫描电镜(SEM)对沉积物的组分和形貌进行了分析.结果表明,吡唑上的取代基、吡唑与格氏试剂的反应配比对电解液的电化学性能都有影响.1 mol·L-11-甲基吡唑-PhMgCl(1:1摩尔比)/THF反应配制的电解液在不锈钢(SS)集流体的阳极氧化分解电位达到2.4 V(vs Mg/Mg2+),并具有镁沉积-溶出电位低、循环稳定性高、配制方便的特点,有希望应用于实际的可充镁电池体系中.     

乙烯硫脲-格氏试剂/THF电解液镁沉积-溶出性能

将乙烯硫脲与不同格氏试剂EtMgBr/THF、PhMgBr/THF、PhMgCl/THF反应制得了3种乙烯硫脲-格氏试剂/THF电解液. 通过循环伏安测试了在Pt电极的镁沉积-溶出性能. 结果表明,形成乙烯硫脲-格氏试剂/THF电解液不改变电解液的镁沉积-溶出性能,却拓宽了其电化学窗口. 如乙烯硫脲-PhMgBr/THF溶液的氧化分解电位可达2.3 V（vs. Mg/Mg²⁺）, 该电解液的电导率随溶液溶度增大先升后降,0.9 mol·L^-1时其电导率最高,可达615 μS·cm^-1. 比较乙烯硫脲-PhMgBr/THF在Pt、Ni、Cu和Al四种金属电极的电化学性能,发现在Ni电极的氧化分解电位最高,可达2.4 V（vs. Mg/Mg²⁺）,且具有良好的镁沉积-溶出性能. CR2016扣式电池的循环测试表明,Ni基底上的镁沉积-溶出电位较低,其循环效率可达到92%,适宜作为实用电池的集流体.     

苯硫酚盐基溶液的可充镁电池电解液

将4-甲基苯硫酚、4-异丙基苯硫酚和4-甲氧基苯硫酚(RSH)分别与格氏试剂C2H5MgCl/THF(四氢呋喃)反应制得的苯硫酚氯化镁(RSMgCl)(分别标记为MBMC、IPBMC和MOBMC)/THF和进一步与Lewis酸AlCl3反应制得的(RSMgCl)n-AlCl3/THF(n=1,1.5,2)苯硫酚盐基溶液用作可充镁电池电解液,采用循环伏安和恒电流充放电测试研究了电解液的镁沉积-溶出性能和氧化分解电位.结果表明,苯硫酚上的基团种类和RSMgCl与AlCl3的比例对其电化学性能有影响.其中,0.5 mol·L-1(IPBMC)1.5-AlCl3/THF溶液具有最佳的电化学性能,其氧化分解电位适宜(2.4 V(vs Mg/Mg2+)),镁沉积-溶出循环效率稳定,过电位低,电导率较高(2.48 mS·cm-1),与正极材料Mo6S8兼容性良好,且具有一定的空气稳定性,配制方便,有希望应用于实际的可充镁电池体系中.     

可充镁电池电解液

由于金属镁具有能量密度较高、价格低、操作安全等优点,可充镁电池是在大负荷储能方面极具发展潜力的二次电池。本文综述了可充镁电池电解液的研究进展,其中包括溶于醚溶剂中的格氏试剂、Mg(BR₂R′₂)₂(其中R、R′为烷基或芳基)、Mg(AX_4-nR_n′R′_n″)₂络合物(其中A=Al、B、Sb、P、As、Fe和Ta等,X =Cl、Br和F,R、R′为烷基或芳基,0相似文献   

可充镁电池正极材料PTMA/石墨烯

本文制备了聚4-甲基丙烯酸-2,2,6,6-四甲基哌啶-1-氮氧自由基酯(PTMA)/石墨烯纳米复合材料,并报道了其作为可充镁电池正极材料的电化学性能.通过傅里叶变换红外(FTIR)光谱、扫描电镜(SEM)、透射电镜(TEM)表征复合材料的结构和形貌;循环伏安和恒电流充放电测试其电化学性能.粒径10 nm左右的PTMA颗粒分散在具有导电作用的石墨烯表面;在"一代"电解液Mg(AlCl2BuEt)2/四氢呋喃(THF)(0.25 mol L-1)中,22.8mA g-1充放电电流密度下,PTMA/石墨烯复合材料的起始放电容量可达到81.2 mAh g-1.研究结果表明,含有自由基的有机化合物可以作为可充镁电池的一类新型正极材料,可以进一步通过使用具有高氧化分解电压的电解液来提高其放电容量.     

镁硫二次电池电解液

镁硫二次电池具有安全性好、成本低、能量密度高等特点,其中电解液是目前制约其发展的关键因素。由于硫电极的亲电子特性,格氏试剂及其衍生物系列的传统镁离子电解液无法适用。本文针对有机镁盐+AlCl_3、MgCl_2+有机铝卤盐、MgCl_2+AlCl_3、Mg(TFSI)_2(双三氟甲烷磺酰亚胺基镁)四类电解质溶液体系进行总结和评述。有机镁盐+AlCl_3电解液的镁硫电池表现出较好的电化学性能,MgCl_2+有机铝卤盐电解液体系与硫电极具有良好的兼容性。而使用Mg(TFSI)_2和MgCl_2+AlCl_3电解液时硫电极的比容量不高,且放电平台低。目前所报道的镁硫电池体系的可逆容量衰减都较大,通过加入电解液添加剂等方法可以改善其放电特性和循环稳定性。本文还总结了电解液中活性阳离子结构、阴离子以及电解液添加剂的作用,并展望了镁硫电池电解液体系的研究趋势。     

非亲核镁硫电池电解液的研究进展

自从Muldoon课题组在2011年首次报道以[Mg2(μ-Cl)3(THF)6]+为阳离子电化学活性中心的非亲核有机铝镁盐用于镁硫电池以来,非亲核镁电解液便引起了人们的广泛关注.本文综述了非亲核镁电解质的合成、阳离子结构及其镁硫电池电解液电化学性能的研究进展.最后对非亲核镁硫电池电解液未来的发展方向进行了前瞻性的探讨...     

集流体对可充镁电池电解液电化学性能的影响

系统研究了铂、镍、不锈钢(SS)、铜、铝五种金属集流体和碳纤维、石墨箔、碳布三种碳纸集流体对“一代” (Mg(AlCl₂BuEt)₂/THF)、“二代” ((PhMgCl)₂-AlCl₃/THF)可充镁电池电解液阳极氧化分解电位和镁沉积-溶出性能的影响。金属镍、不锈钢、铜、铝作为可充镁电池正极的集流体时, 充电至一定电压时自身均会发生腐蚀。其中, 镍和不锈钢可用作充电电压在2.1V(vs Mg/Mg²⁺)以下正极材料的集流体; 铜可用作充电电压在1.8V(vs Mg/Mg²⁺)以下正极材料的集流体。碳集流体比金属集流体具有更高的稳定性, 其中, 碳布作为集流体, 适用于充电电压在2.25V(vs. Mg)(对“一代”电解液)和2.95V(vs Mg/Mg²⁺)(对“二代”电解液)以下的正极材料。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.