Utilization of four WDM channels with signal remodulation of OFDM-QAM for 10 Gb/s uplink passive optical networks

In this investigation, we experimentally investigate an extended reach (ER) time-division-multiplexed passive optical network (TDM-PON) using four wavelength-multiplexed channels to achieve 16 Gb/s downlink and 10 Gb/s uplink traffic. Each downlink signal uses the highly spectral efficient 4 Gb/s OFDM-QAM, and each uplink signal is generated by signal remodulating the downlink signal via a reflective semiconductor amplifier (RSOA) at 2.5 Gb/s non-return-to-zero (NRZ). In addition, the performance of the proposed ER TDM-PON has also been analyzed and discussed.     

Transmission performance of 20 × 10 Gb/s WDM signals using cascaded optimized SOAs with OOK and DPSK modulation formats

We investigated 20 channels at 10 Gb/s wavelength division multiplexing (WDM) transmission over 1190 km single mode fiber and dispersion compensating fiber using cascaded inline semiconductor optical amplifier at a span of 70 km for RZ-DPSK (return zero differential phase-shift keying) modulation format by using same channel spacing, i.e. 100 GHz. We show for RZ-OOK (return zero on-off keying) format a transmission distance of up to 1050 km with Q factor more than 15 dB, without any power drops. We developed the SOA model for inline amplifier having minimum cross-talks and ASE (amplified spontaneous emission) noise power with sufficient gain. At optimal bias current of 400 mA, a high constant gain of 36.5 dB is obtained up to a saturation power of 21.36 mW. So reduction of cross-talk and distortion is possible by decreasing the bias current at appropriate amplification factor.The DPSK modulation format has less cross-talk as compared to OOK format for nonlinearities and saturation case. The impact of optical power received and Q factor at different distance for both RZ-OOK and RZ-DPSK modulation format has been illustrated. We have shown the optical spectrum and clear Eye diagram at the transmission distance of 1190 km in RZ-DPSK system and 1050 km in RZ-OOK systems.The bit error rate (BER) for all channels observed is less than 10⁻¹⁰ up to gain saturation for both DPSK and OOK systems. Finally, we investigated that the transmission distance decreases with a decrease in channel spacing of up to 20 GHz.     

Adding channels with PSBT format at 40 Gbit/s in an existing 10 Gbit/s optical network

Until recently, the wavelength-division-multiplexed (WDM) transmission system has reached record capacities and distances due to innovations such as FEC (Forward Error Correction), distributed Raman amplification, new transmission fiber and advanced optical format. Optical-communication systems exclusively employed conventional On-Off Keying signals in either Non-Return-To-Zero (NRZ) or Return-To-Zero (RZ) format. Recently a number of advanced modulation formats have attracted attention. Some of these formats carry information through On-Off-Keying but also modulate the optical phase in order to enhance the robustness of signal to chromatic dispersion, optical filtering and non-linearities. Through extensive sets of simulation results, we showed that it is possible to replace a channel with higher bit-rate on existing DPSK or OOK at 10Gbit/s transmission link. Duobinary formats are ideal candidates to do it and are known for their low spectral range and high tolerance to residual chromatic dispersion. These particularities make them very attractive for both high bit rates and high distance-transmissions. Today, Phase Shaped Binary Transmission (PSBT) is considered as being the promising format for the deployment of 40Gbit/s technology on existing links at 10Gbit/s WDM long haul transmissions.     

Multi-wavelength conversion at 10 Gb/s using cross-phase modulation in highly nonlinear fiber

In this paper we demonstrate a technique of signal wavelength conversion via cross-phase modulation (XPM)-induced nonlinear coupling among a 10 GHz return-to-zero (RZ) signal and a continuous wave (CW) carrier co-propagating in dispersion-shifted (DS) highly nonlinear fiber (HNLF). The wavelength conversion bandwidth up to ±20 nm was achieved experimentally and potential extension was verified by numerical simulations. The principle can easily be extended to 40 Gb/s and used as polarization insensitive all-optical wavelength converter.     

10 Gb/s TDM passive optical networks using four wavelengths multiplexed channels

We propose a new architecture for 10 Gb/s upstream traffic in TDM-PON using externally injection-locked Fabry-Perot laser diodes (FP-LDs) in each optical network unit (ONU). Four directly modulated 2.5 Gb/s FP-LDs were injection-locked by continuous wave (CW) carriers distributed from the optical line terminal (OLT). Hence, a total of 10 Gb/s upstream traffic can be achieved. Experimental results show negligible power penalty at a transmission of 25 km standard single mode fiber (SMF) without dispersion compensation. The performance of the injection-locked FP-LD is also studied.     

Effectiveness of electronic equalizer for filter concatenation effect of low-cost 2.5 Gb/s rated DML sources operated at 10 Gb/s

The improvement on the impact of filter concatenation effect on optical signal quality is investigated and discussed for applications in metropolitan optical networks utilizing cost-effective 10-Gb/s transmitters. The sources are low-cost conventional directly modulated lasers (DMLs), fabricated for operation at 2.5 Gb/s but modulated at 10 Gb/s. Performance improvement is achieved by using decision-feedback equalization (DFE) at the receiver end. Experimental studies consider both transient and adiabatic chirp dominated DMLs sources with different chirp characteristics. Measurements have been obtained using a recirculating loop set-up and the performance improvement is evaluated in terms of bit-error-rate (BER) versus number of loops.     

10 Gb/s broadband silicon electro-optic absorption modulator

Here we propose a design for a novel broadband silicon electro-optic absorption modulator. The device is simply a 100 µm long silicon waveguide with a Schottky diode integrated in it. Modulation is achieved through free-carrier absorption, not interference effects, enabling operation over the entire bandwidth of the waveguide. The high overlap between the modulated carrier density and the optical mode enables high speed (> 10 Gb/s), small footprint and modulation depths of ∼ 4.6 dB.     

1.6 μm band double pass fiber Raman amplifiers using Raman fiber oscillator

We propose double pass fiber Raman amplifier schemes based on Raman fiber oscillator in order to amplify optical signal with wavelengths from 1610 to 1650 nm efficiently. We experimentally demonstrate that the proposed double pass amplifier scheme has enhanced gain characteristics compared to a conventional single pass scheme. We also demonstrate a scheme for the proposed double pass amplifier to have small gain variation over the wavelength range by using two fiber Bragg gratings with different center wavelengths.     

Optimizing the thulium doped fiber amplifier (TDFA) gain and noise figure for S-band 16 × 10 Gb/s WDM systems

This paper aims to evaluate a comprehensive numerical model based on solving rate equations of a thulium-doped silica-based fiber amplifier. The pump power and thulium-doped fiber (TDF) length for single-pass thulium-doped fiber amplifiers (TDFA) are theoretically optimized to achieve the optimum gain and noise figure (NF) at the center of S-band region. The 1064 nm pump is used to provide both ground-state and excited state absorptions for amplification in the S-band region. The theoretical result is in agreement with the published experimental result.     

All-optical generation of 40 Gb/s single sideband signals using a fiber Bragg grating

In this work, we demonstrate a reliable all-optical technique for performing optical double sideband (ODSB) to single sideband (OSSB) format conversion of a 40 Gb/s non-return-to-zero signal. It is based on the optimization of a detuned optical filter, which was implemented on a fiber Bragg grating (FBG) with a complex apodization profile. An OSSB signal with negligible distortion was obtained, as the FBG presented a nearly ideal frequency response. Higher tolerance to chromatic dispersion enabled by the OSSB signal in comparison to the ODSB signal was demonstrated on both simulation and experimental results.     

10 Gb/s WDM-PON based on FP-LDs injection locked by downlink optical carrier

We propose and demonstrate a 10 Gb/s wavelength division multiplexed passive optical network (WDM-PON) where subcarriers are employed to transmit the downstream data and optical carriers of the downlink subcarrier modulated (SCM) lights are reused to injection lock Fabry-Perot laser diodes (FP-LDs) for uplink transmission. Experiment results show that a very good BER performance can be achieved for both uplink and downlink at 10 Gb/s. The impact of optical carrier to subcarrier ratio and wavelength mismatching is also investigated.     

Significance of prechirping on long-haul path-averaged soliton impulse in re-circulating loop at 10 and 20 Gb/s with TOD

In this paper, we have investigated the performance of first- and second-order path-averaged soliton long-haul transmission link including the impact of third-order dispersion (TOD) at varied chirp. Here, the varied chirp is considered keeping in view the inadvertent frequency chirp imposed on all practical sources of short optical pulses. The propagation of strongly chirped pulses in loss-managed long-haul path-averaged soliton transmission network has been shown. The investigations reveal that in first-order (N=1) path-averaged soliton transmission link at 10 and 20 Gb/s, SPM effect on the rising and falling edges of a pulse results in spectral broadening for all values of induced chirp. On the contrary, spectral narrowing of the pulses is observed in second-order negatively chirped path-averaged soliton pulses. The effect of the nonlinearity changes from narrowing to broadening of pulses if the sign of the initial chirp is changed to positive. The results ascertain that the system is capable of transmitting a pulse up to the distance of 24,500 km at bit rates of 10 and 20 Gb/s. Investigations have been carried out by varying the chirp factor in the range −1 to 1 and −1 to 0.4] for 10 and 20 Gb/s, respectively, to demonstrate the robustness of the long-haul soliton link. The observations establish that the pulse width (full-width at half-maximum (FWHM)) remains within the optimal range even at the transmission distance of 24,500 km without and at discrete values of the chirp factor.     

Impact of optical modulation formats on SPM-limited fiber transmission in 10 and 40 Gb/s optimum dispersion-managed lightwave systems

In this paper, 10 and 40 Gb/s optical systems have been investigated for nonreturn-to-zero (NRZ), return-to-zero (RZ), carrier-suppressed return-to-zero (CSRZ) and RZ-differential phase-shift-keying (RZ-DPSK) data formats. For the range of the optical signal power from −5 to 15 dBm, a maximum self-phase modulation (SPM)-limited transmission distance L_SPM is determined with eye-opening penalty (EOP) >1 dB .The observations are based on the modeling and numerical simulation of optimum dispersion-managed transmission link. Transmission over distances of the order of several hundreds of kilometers has been shown with and without amplified spontaneous emission (ASE) noise of the in-line erbium-doped fiber amplifiers (EDFAs).     

Simulation of Fiber to the Home at 10 Gbit/s using GE-PON architecture

In this paper, a fiber communication system is employed using Giga Ethernet Passive Optical Network (GE-PON) architecture. In this architecture an optical fiber is employed directly from a Central Office to the home. A 1:8 splitter is used as a PON element which establishes communication between a Central Office to different users. The architecture has been investigated for different lengths from a Central Office to the PON in terms of BER. For 10 Gbit/s system the plots between the BER and transmission distance are plotted and it are seen that as the distance increases beyond the 15 km the BER is increased very sharply. The results in the form of voice and data spectrum for different users of FTTH with GE-PON architecture are shown.     

Ultra high-speed optical signal processing based on single SOA at 60 Gb/s

The paper shows the design of all-optical logic gates OR, AND, NOT, NOR, XNOR, XOR at ultra high speed by using SOA. The simulations of all logic gates are obtained by XGM and FWM in SOA at 40 Gb/s and 60 Gb/s. The OR, AND, NOR logic between two data sources are obtained using a pump signal, while another logic XNOR using two data. The NOT, XOR obtained using FWM and XGM combined. Thus realization of these logics at 40 Gb/s and 60 Gb/s will lead revolution growth in optical signal processing for high-speed operation.     

Turbo-switched Mach-Zehnder interferometer performance as all-optical signal processing element at 160 Gb/s

Two variations of the active Mach-Zehnder interferometer (MZI) that incorporate the recently proposed turbo-switch effect are introduced to carry out three key functionalities in forthcoming high-speed optical telecommunication networks, namely, all-optical wavelength conversion, photonic XOR gating and optical time-division demultiplexing. Their performance is numerically investigated at 160 Gb/s using a sophisticated semiconductor optical amplifier (SOA) model. The more practical of the two proposed geometries shows error-free operation as XOR Boolean gate, low patterning as wavelength converter, and poor performance as demultiplexer. For comparison, results derived from well-accepted (or typical) schemes are also presented, and the role of the required extra SOAs as distinguishing elements of the new architectures is investigated.     

Analysis of 160 Gb/s all-optical NRZ-to-RZ data format conversion using quantum-dot semiconductor optical amplifiers assisted Mach-Zehnder interferometer

A scheme of all-optical data format conversion from nonreturn-to-zero to return-to-zero is proposed using quantum-dot semiconductor optical amplifiers (QD SOAs) assisted Mach-Zehnder interferometer (MZI). The proposed scheme has the potential to operate at much larger bit rate ∼160 Gb/s, and the converted signal has a lower frequency chirp. 160 Gb/s all-optical format conversion is verified through numerical simulations, and the output contrast ratio and Q-factor are analyzed to evaluate the system performance. With properly selected parameters, the converted signal with a contrast ratio over 8 dB and a Q-factor over 8 can be achieved.     

Si-based near infrared photodetectors operating at 10 Gbit/s

We report on fast p-i-n near infrared photodetectors in pure germanium on silicon. The diodes were fabricated by chemical vapor deposition at 600 °C followed by thermal annealing at 900 °C. We also verified that bypassing the thermal treatment did not have significant effects on the resulting crystal quality, allowing to considerably reducing the thermal budget hence simplify the integration with silicon. We demonstrate the operation of photodiodes with responsivities of 0.4 and 0.2 A/W at 1.3 and 1.55 μm, respectively, as well as open-eye diagrams at 10 Gbit/s.     

Reduction of the fiber nonlinearity impairment using optical phase conjugation in 40 Gb/s CO-OFDM systems

In this paper, optical phase conjugation (OPC) located in the transmitter based on four wave mixing (FWM) in a semiconductor optical amplifier (SOA) is first simulated in 40 Gb/s CO-OFDM systems, and the fiber nonlinearity impairment of the transmission link is precompensated before OPC by transmission through a fiber with large nonlinearity coefficient. Simulation results show that the nonlinear threshold (NLT) can be increased by about > 3 dB and maximum Q factor can be increased by about 2 dB for the single-channel system. For 50-GHz-Spacing WDM systems, the maximum Q and NLT are increased by about 1 dB, even in the presence of cross phase modulation (XPM) from neighbouring WDM channels. It is found that this OPC subsystem located in the transmitter, not necessary to be inserted into the middle of link, can mitigate the fiber nonlinearity impairment for both single-channel and WDM systems.     

Comparative investigation and suitability of various data formats for 10 Gb/s optical soliton transmission links at different chirps

This paper presents the comparative investigation and suitability of various data formats for optical soliton transmission links at 10 Gb/s for different chirps (−0.7 to 0.7). Here the investigations focused on data formats: NRZ, RZ soliton, RZ raised cosine and RZ super Gaussian. The comparative results and suitability of data formats is based on various performance measures such as Q-factor, eye opening, BER and jitter. It has been indicated that RZ super Gaussian yields the highest value of Q (34.08 dB), good eye opening and lowest BER.