Realization of optoelectronic integrated transmitter and receiver for POF Applications

The optoelectronic integrated transmitter and receiver for 650 nm plastic optical fiber (POF) communication applications realized in 0.5 μm BCD (Biplor, CMOS and DMOS) process is first described in this paper. The 650 nm resonant cavity light emitting diode (RCLED) is used as light source. It is first proposed for optoelectronic integration of the transmitter by bonding RCLED to the driver chip. Temperature compensation technology is employed in the driver circuit to compensate for the modulation current. In the monolithic optoelectronic integrated receiver, large area multi-finger PIN photodetector (PD) that is compatible with standard IC process, transimpedance amplifier and post amplifier are presented. Measurement results show that the responsivity and capacitance of PD is 0.25 A/W and 5 pF, respectively. The sensitivity of receiver is −14.6 dBm at 180 Mb/s and BER is less than 10⁻⁹ for 650 nm input light by POF. A clear eye diagram is demonstrated for 180 Mb/s PRBS. These indicate that optoelectronic integrated chips can be employed in high-speed POF-based Fast Ethernet systems for broadband access network applications.     

Optimal design of 32 channels spectrum slicing WDM for optical fiber access network system

In this article, the spectrum sliced dense wavelength division multiplexed passive optical network (SS-DWDM–PON) has been investigated as a power efficient and cost effective solution for optical access networks. In this work an AWG demultiplexer is used to operate as slicing system. The high speed SS-DWDM system has been realized and investigated for 32 channels with data rate up to 3 Gb/s using broadband ASE source (LED). The 3 Gb/s signals both non-return-to-zero (NRZ) and return-to-zero (RZ) were demonstrated in 40 km optical fiber link with BER < 10⁻¹². The results obtained here demonstrate that SS-DWDM is well suited for Fiber-to-the-Home (FTTH) network.     

Optical encoder based on Fractional-Talbot effect using two-dimensional phase grating

This work presents an optical encoder that uses a two-dimensional phase grating. Rather than using a four-windowed scanning grating, this design with a special two-dimensional phase index grating generates two sinusoidal signals that are mutually phase-shifted by 180°. Afterwards, two large-areas, specially structured index grating generates the four 90° electrically phase-shifted scanning signals. The special design of the two-dimensional phase index grating provides more accuracy of phase-shift by using the fact that the  + 1 and −1 diffraction orders are intrinsically phase-shifted from one another by 180°. The gap between the phase index grating and mail scale was increased to three quarters of Talbot distance. The tolerance of gap between the index and main grating is 0.1 mm. The tolerance of yaw motion is ± 0.25°.     

Design of high duty ratio nonlinear photonic crystal fiber with near-zero flattened dispersion after 1.205 μm

The paper presents a high nonlinear photonic crystal fiber (HN-PCF) with highly duty ratio for time-stretch analog-to-digital conversion (TSADC). The simulation results show that a nonlinear of 42.26 W⁻¹ km⁻¹ and the flattened dispersion of less than 1.0 ps/(nm km) are obtained in more than 495 nm waveband (1205–1700 nm). Owing to its high nonlinear coefficient and flattened dispersion, the high nonlinear PCF is expected to be suitable for supercontinuum (SC) generation. The numerical simulation results demonstrate that the proposed high duty ratio HN-PCF can generate wideband SC.     

Reduction of frequency fading and imperfect frequency response with pre-emphasis technique in OFDM-ROF systems

In this paper, a novel technique is proposed and experimentally demonstrated to reduce the effect of frequency fading (FF) and imperfect frequency response in direct-detection (DD) optical orthogonal frequency division multiplexing-radio-over-fiber (OFD-MROF) systems. To overcome FF effect in the optical fiber and imperfect frequency response in the optical and electrical devices at the high frequency, we pre-emphasize the power of the millimeter wave (mm-wave) OFDM sub-carriers appropriately in the center station. Experimental result of the proposed system shows the received sensitivity has been improved about 2 dB at the BER of 1 × 10^− 4 after 50 km SSMF transmission for 2.5 Gb/s OFDM signal carried on 60 GHz optical mm-wave compared to the original system without pre-emphasis technique.     

High-speed CMOS readout integrated circuit for large-scale and high-resolution microbolometer array

A new CMOS readout integrated circuit (ROIC) for microbolometric focal plane array (FPA) is proposed in this paper. By applying multiple-module parallel working technique, the pixel readout speed of the CMOS ROIC can reach 10 MHz, which is very suitable for large-scale microbolometer array. The CMOS ROIC of each parallel working module consists of three major parts: direct injection (DI) input circuits, column-shared integrating circuits, and common noise-suppressing circuits. The readout structure of the ROIC is simple because of the DI input, shared and common circuits, and this makes the ROIC satisfy the requirements of small-pixel microbolometric FPA. Furthermore, the voltage signals from different working modules can be output according to a certain order through a high-speed output circuit. An experimental readout chip based on the proposed ROIC has been designed and fabricated to verify its readout function and performance. The measurement results of the experimental readout chip have successfully proved that the proposed CMOS ROIC can be applied to high-speed, low-noise, large-scale and high-resolution microbolometric FPA.     

The effect of laser remelting in the formation of tunable nanoporous Mn structures on mild steel substrates

Nanoporous manganese was fabricated by a three-step process involving high power laser cladding of a homogeneous Cu₄₀Mn₆₀ alloy coatings onto a mild steel substrate, laser remelting for tuning the grain size and the composition homogeneity followed by selectively electrochemical de-alloying for removal of Cu element and formation of nanoporous Mn. The microstructure and homogeneity of the precursor Cu₄₀Mn₆₀ alloys have a significant influence on the evolution of nanopores during selectively electrochemical de-alloying. Laser remelting can significantly refine the microstructure. The second dendrite arm spacing decreases with increasing of laser remelting scanning speed. A SDAS of 1.17 μm was obtained at the laser scanning speed of 133 mm/s. When the remelting scanning speed reaches 100 mm/s, a nanoporous structure with average pore size less than 100 nm was achieved under optimized dealloying electrode current density about 2 mA/cm². Nanoporous Mn with nanopore sizes ranging from 80 to 130 nm was fabricated by this method. Surface-enhanced Raman scattering characteristics of the nanoporous materials have been investigated. It is found that smaller nanoporosity leads to significant improvements in surface-enhanced Raman scattering.     

一种基于容栅编码器测量炮塔高精度动态转角的方法

容栅编码器是在传统容栅技术上发展起来的新型传感技术,针对目前炮塔相对地盘转角的高精度测试需求,提出了一种基于容栅编码器测量高精度动态转角的方法。结合炮塔环境,设计了容栅测角装置的安装方式,分析了测角装置的工作原理,通过机械结构设计和容栅编码器后续的电路设计,提高了其工作的稳定性与可靠性。对测角装置分别进行了实验室角度标定与某靶场实地试验,结果表明:该测角系统能够满足实际需求,具有断电保护、通电位置识别及零位记忆等功能,测试精度达60。     

Design and analysis of a photonic crystal fiber with four-hole unit

A novel photonic crystal fiber (PCF) based on a four-hole unit is proposed in order to meet the requirements of high birefringence, negative dispersion and confinement loss in fiber-optic communication. The proposed design has been simulated based on the full vector finite element method (FVFEM) and anisotropic perfectly matched layers (APML). Analysis results show that the proposed PCF can achieve a high birefringence to the order of 10⁻² at the wavelength of 1.55 μm, a large negative dispersion over a wide wavelength range and confinement losses lower than 10⁻⁹ dB/m simultaneously, which has important applications in polarization-maintaining (PM) fibers, single-polarization single-mode (SPSM) fibers, dispersion compensation fibers and so on.     

Splitting-on-demand optical power splitters using multimode interference (MMI) waveguide with programmed modulations

Reconfigurable multi-channel optical power splitter is proposed and its optical properties are calculated. The device can dynamically reconfigure the number of splitting channels by providing programmed refractive index modulations on a multimode interference (MMI) waveguide. A reconfigurable 3-channel optical power splitter is designed to work as 1 × 1, 1 × 2 or 1 × 3 optical power splitter depending on the state of the heat electrodes using thermo-optic modulation, and the input light can be distributed to three output channels with sequential orders. The device can work in the whole C-band (1530-1565 nm) with extinction ratio better than −29.0 dB, excess loss better than −0.45 dB, imbalance better than 0.08 dB and polarization dependent loss (PDL) better than 0.14 dB. The design conception is scalable to a multi-channel splitting-on-demand optical power splitter which can divide input light to 1, 2, …, N output channels equally by using the 3-channel reconfigurable optical power splitter as a building block.     

Using Fabry-Perot laser diode and reflective semiconductor optical amplifier for long reach WDM-PON system

In this investigation, we propose and investigate the simple self-injection locked Fabry-Perot laser diodes (FP-LDs) in optical line terminal (OLT); and wavelength-tunable optical network unit (ONU) using reflective optical semiconductor amplifier (RSOA) and FP-LD laser for downstream and upstream traffic in long reach (LR) wavelength division multiplexed-passive optical network (WDM-PON) respectively. The output performance of the proposed two laser sources in terms of power and side-mode suppression ratio (SMSR) has been discussed. Here, for the downstream traffic, the proposed optical transmitter can be directly modulated at 2.5 Gb/s on-off keying (OOK) format with nearly 0.4 dB power penalty at bit error rate (BER) of 10⁻⁹ through 75 km single-mode fiber (SMF) transmission. Moreover, the proposed upstream transmitter can be directly modulated at 1.25 and 2.5 Gb/s with nearly 0.5 and 1.1 dB power penalty, respectively, at the BER of 10⁻⁹.     

基于线阵探测器的单圈绝对轴角编码器

为了解决轴角编码器尺寸与角度分辨率之间的矛盾,同时提高编码器的响应频率,提出了一种基于线阵探测器的单圈绝对式光电轴角编码器.该编码器使用了一种新型单圈绝对式编码盘,整个码盘只有一个码道,粗码被直接刻在这个单圈的码道上,码盘图像经光学放大后被线阵探测器接收.利用FPGA控制电路将数据传送至计算机,并对数据进行译码处理,分别利用图像处理技术读取粗码和利用像素细分技术获得细码,两者相结合得到角度信息.通过该技术设计一个码盘直径为40 mm的绝对式轴角编码器,其分辨率为15位.     

Enhanced performance analysis of optical CDMA communication system

Optical CDMA technique is required to meet the increased demand for high speed, large capacity communications in optical networks. OCDMA assures data access security and supports asynchronous burst data transmission. In this paper, improvement in optical CDMA has been done by implementing forward error correction technique and a distance of 100 km was achieved BER 10⁻¹⁹ at bit rate 3.75 Gbps with forward error correction in optical CDMA.     

Studies of magnetic properties of permalloy (Fe-30%Ni) prepared by SLM technology

In the present study, a high permeability induction Fe-30%Ni alloy cubic bulk was prepared by the selective laser melting process. In order to reveal the microstructure effect on soft magnetic properties, the microstructure and magnetic properties of the Fe-30%Ni alloy were carefully investigated by scanning electron microscopy, X-ray diffraction and hysteresis measurements. The bcc-Fe (Ni) phase formation is identified by X-ray diffraction. Meanwhile, it was found that low bcc lattice parameter and high grain size could be obtained when high laser scanning velocity and low laser power were used. Moreover, the lowest value of coercivity is 88 A/m, and the highest value of saturation magnetization is 565 Am²/kg, which can be obtained at a low laser scanning velocity of 0.4 m/s and high laser power input at 110 W.     

复合式光电编码器精密轴系设计及准确度分析

 为了提高复合式光电编码器的轴系准确度,运用一个径向密珠轴承与两个轴向止推密排轴承相结合的结构设计了大空心轴精密轴系,并对轴系误差进行分析.通过该方法设计的精密轴系径向跳动δ＜3 μm,解决了大空心轴轴系准确度差的问题,提高复合式编码器的测角准确度,应用该轴系研制的复合式光电编码器准确度σ＜2″.     

Low temperature radio-frequency transverse susceptibility measurements using a CMOS oscillator circuit

A transverse susceptibility (TS) measurement system based on a simple inverter CMOS cell oscillator cross-coupled to a LC tank is presented. The system has been implemented to operate at a Quantum Design Physical Properties Measurement System (PPMS). We introduce several improvements with respect to similar currently operating TS measurement equipments. The electronics have been redesigned to use CMOS transistors as active devices, which simplifies the circuit design and enlarge the tuning range, thus making the proposed electronic block more feasible, predictable, and precise. Additionally, we propose a newly designed sample holder, which facilitates the procedure to change a sample and improves reproducibility of the circuit. Our design minimizes the thermal leak of the measuring probe by one order of magnitude, allowing to measure from 1.8 K in standard PPMS systems, thanks to the use of a low temperature beryllium–copper coaxial cable instead of the conventional RG402 Cu coaxial cable employed in the insert for the PPMS in similar systems. The data acquisition method is also simplified, so that the measuring sequences are implemented directly in the PPMS controller computer by programming them in the Quantum Design MultiVu software that controls the PPMS. We present the test measurements performed on the system without sample to study the background signal and stability of the circuit. Measurements on a Gd₂O₃ calibrating sample yield to the estimation of the system sensitivity, which is found to be on the order of 10⁻⁶ emu. Finally, measurements on a TmCo₂ Laves phase sample with a ferrimagnetic transition temperature around 4 K are described, demonstrating that the developed system is well suited to explore interesting magnetic phenomena at this temperature scale.     

Experimental demonstration of polarization multiplexing for simultaneously providing broadband wireless and wired access

A fiber-based wavelength-division-multiplexing (WDM) network utilizing polarization multiplexing (PolMUX) is proposed to simultaneously provide broadband wireless and wired services. In such a dual-service access network, the wireless and wired services are separately delivered in two orthogonal states of polarization with well independence in a single WDM channel. The impact of several polarization-dependent interferences becomes insignificant due to the relatively short transmission distance in access networks. The feasibility of PolMUX is experimentally demonstrated with a power penalty at BER = 10^-9 of about 0.5 dB and 1 dB for 2.5 Gb/s wired and wireless downstream services, respectively. The proposed system is compatible with the current reported techniques in either WDM passive optical networks (WDM-PON) or radio-over-fiber (ROF) systems.     

A divided spectrum balanced detection technique for intensity noise reduction in SAC OCDMA systems

In this paper we propose a simple divided spectrum balanced detection (DSBD) for spectral amplitude coding (SAC) optical code division multiple access (OCDMA) systems. SAC OCDMA systems are limited by phase induced intensity noise (PIIN), which is a signal dependent source of noise. Our proposed technique reduces the PIIN by dividing the spectrum of the signal into two or more, and detecting each spectrum by a different photodiode. The DSBD scheme reduces the detected optical power at photodetection, thus resulting in a higher mitigation of the PIIN. Theoretical results show that DSBD demonstrate noticeable improvement over traditional balanced detection technique, for example an up to 33% increase in the number of active users can be achieved, and at least 1 × 10⁻³ b/s Hz increase in the spectral efficiency is obtained. However, the SDBD is more complex and append more constrains on system components.     

Reconfigurable all-optical logic gate using four-wave mixing (FWM) in HNLF for NRZ-PolSK signal

We demonstrate a reconfigurable all-optical logic gate for NRZ-PolSK signal based on FWM in a highly nonlinear fiber at 10 Gb/s. Half subtracter, XOR, AB?, āB or XNOR, AND, and NOR logic gates can be implemented simultaneously. The input power for the HNLF is optimized to be as low as about 15.2 dBm and the high Q factors above 8 dB for eye diagrams are achieved. Experimental results show Q factors of AB?, āB, AND, and NOR were higher than those of XOR, and XNOR. Error-free operation is achieved experimentally for 10 Gb/s 2⁷-1 pseudorandom bit sequence (PRBS) data. Power penalties for the logic gate are less than 3 dB. Simulation analysis about the wavelength characteristic for all logic gates is given and it predicts that the reconfigurable logic gate can realize error-free operation when the wavelength separation is less than 5 nm.     

Parity checking and generating circuit with semiconductor optical amplifier in all-optical domain

In this paper, an all-optical parity checker and parity generator circuit is proposed in which SOA-MZI configuration is used to implement the XOR logic gate. This performance monitoring logic device is simulated at ultra high speed i.e. 120 GHz. Two logic circuits are proposed for parity generator, in one design inverter used to generate parity bit is implemented by the same additional XOR gate as inverter while in 2nd design inverter is implemented using XGM in SOA and thus number of SOA in 2nd design is reduced. ER ratio achieved in 1st case is 9.28 with maximum Q factor 73.39 and minimum BER 0 while in 2nd design it is 9.35 with maximum Q factor 8.41 and minimum BER 1.93e−17. ER ratio achieved in parity checker circuit is 32.54 with maximum Q factor 77.76 and minimum BER 0.