The low temperature synthesis of Euand Dy activated Sr3Al2O6 nanophosphors by microwave method

The Eu²⁺and Dy³⁺ activated Sr₃Al₂O₆ (S3A2O-ED) nanophosphors were synthesized by a new microwave method. The S3A2O-ED sample calcined in microwave oven at around 650 °C for 20 min possesses a cubic Sr₃Al₂O₆ single phase. The sample showed small size (80–100 nm) and spherical shape. The excitation and emission spectra indicated that excitation broad band chiefly sited in visible range and the nanophosphors emitted strong light at 611 nm under around 473 nm excitation. Comparing with conventional method, the microwave synthesis of S3A2O-ED greatly decreased the calcining temperature and time. However, the brightness of S3A2O-ED nanophosphors was reduced. The change of luminescent intensity in S3A2O-ED nanophosphors could be attributed to the effect of surface energy.     

Luminescent properties of green- or red-emitting Eu-doped Sr3Al2O6 for LED

Eu²⁺-doped Sr₃Al₂O₆ (Sr_3−xEu_xAl₂O₆) was synthesized by a solid-state reaction under either H₂ and N₂ atmosphere or CO atmosphere. When H₂ was used as the reducing agent, the phosphor exhibited green emission under near UV excitation, while CO was used as the reducing agent, the phosphor mainly showed red emission under blue light excitation. Both emissions belong to the d-f transition of Eu²⁺ ion. The relationship between the emission wavelengths and the occupation of Eu²⁺ at different crystallographic sites was studied. The preferential substitution of Eu²⁺ into different Sr²⁺ cites at different reaction periods and the substitution rates under different atmospheres were discussed. Finally, green-emitting and red-emitting LEDs were fabricated by coating the phosphor onto near UV- or blue-emitting InGaN chips.     

Dy含量对红色长余辉发光材料Sr3Al2Ｏ6:Eu2＋,Dy3＋性能的影响

采用溶胶凝胶法制备了Sr₃Al₂Ｏ₆:Eu^2＋,Dy^3＋红色长余辉发光材料,利用X射线衍射仪对材料的物相进行了分析,结果表明,1200℃下制备的样品的物相为Sr₃Al₂Ｏ₆,少量的Eu和Dy掺杂没有影响样品的相组成.采用荧光分光光度计、照度计测定了样品的发光特性.结果表明Sr₃Al₂Ｏ关键词： 红色长余辉 3Al₂Ｏ₆')" href="#">Sr₃Al₂Ｏ₆ 溶胶凝胶法     

Conductivity and water uptake of Sr4(Sr2Nb2)O11·nH2O and Sr4(Sr2Ta2)O11·nH2O

The hydrated oxygen deficient complex perovskite-related materials Sr₄(Sr₂Nb₂)O₁₁·nH₂O and Sr₄(Sr₂Ta₂)O₁₁·nH₂O were studied at high water vapour pressures over a large temperature range by electrical conductivity measurements, thermogravimetry (TG), and X-ray powder diffraction (XRPD). In humid atmospheres both materials are known to exhibit protonic conductivity below dehydration temperatures, with peak-shaped maxima at about 500 °C. In this work we show that the peaks expand to plateaus of high conductivity from 500 to 700 °C at a water vapour pressure of 1 atm. However, in situ synchrotron XRPD of Sr₄(Sr₂Nb₂)O₁₁·nH₂O as a function of temperature shows that these observations are in fact coincident with melting and dehydration of a secondary phase Sr(OH)₂. The stability of Sr₄(Sr₂Nb₂)O₁₁·nH₂O and Sr₄(Sr₂Ta₂)O₁₁·nH₂O in humid atmospheres is thus insufficient, causing decomposition into perovskites with lower Sr content and SrO/Sr(OH)₂ secondary phases. This, in turn, rationalizes the observation of peaks and plateaus in the conductivity of these materials.     

Optical study of Sr2SnO4:Eu phosphor

This work presents the influence of europium dopant on optical properties of Sr₂SnO₄:Eu³⁺ powders fabricated by a facile low temperature method. Powders were obtained from the same amounts of Eu³⁺ doping into the different concentrations of Sr(NO₃)₂. Powders were examined by means of scanning electron microscopy (SEM), X-ray diffraction (XRD), and photoluminescence (PL). SEM measurements different Eu concentrations in fabricated powders was determined to found different morphologies. XRD analysis revealed the existence of crystalline Sr₂SnO₄ in the form of tetragonal and the diffraction intensity was remarkably changed. PL studies showed a red luminescence of Sr₂SnO₄:Eu³⁺ powders. The intensity of luminescence increased with better crystallinity. This approach provides economically viable route for large-scale synthesis of this kind of nanopowders.     

Highly water resistant surface coating by fluoride on long persistent Sr4Al14O25:Eu/Dy phosphor

A novel and efficient method of providing moisture resistance of inorganic particles such as divalent europium activated strontium aluminate phosphors (Sr₄Al₁₄O₂₅:Eu²⁺/Dy³⁺) was developed by firing the phosphor in the presence of appropriate amount of ammonium fluoride at a temperature of 600-700 °C. Scanning electron microscopy, X-ray diffraction, FT-IR, EDAX and Photoluminescence measurements were carried out to characterize the uncoated and coated samples. The pH measurements were carried out for the water resistivity measurements. The phosphor particles became coated with a moisture-impervious thin coating that did not suppress the luminescence of the phosphor and can withstand complete immersion in water for long periods of time, showing very high water resistivity.     

Density functional analysis of the magnetic structures of Sr2MGe2O7 (M=Mn,Co)

To examine the difference between the magnetic structures of Sr₂MGe₂O₇ (M=Mn, Co), we evaluated their spin exchange interactions by performing energy-mapping analysis based on density functional theory calculations. The calculated intra- and inter-layer spin exchanges correctly predict the G-type and C-type antiferromagnetic structures of Sr₂MnGe₂O₇ and Sr₂CoGe₂O₇, respectively, and the Curie–Weiss temperatures estimated from these spin exchanges are also in good agreement with the experiment. The ∥c and ⊥c orientations of the spins in the ordered magnetic structures of Sr₂MnGe₂O₇ and Sr₂CoGe₂O₇, respectively, were also examined by considering spin–orbit coupling.     

Enhanced luminescent properties of long-persistent Sr2MgSi2O7:Eu, Dy phosphor prepared by the co-precipitation method

Sr₂MgSi₂O₇:Eu²⁺, Dy³⁺ phosphors were prepared by the (aminopropyl)-triethoxysilane (APTES) co-precipitation method. Effects of synthesis temperature on the crystal characteristics, luminescent properties and afterglow performance of Sr₂MgSi₂O₇:Eu²⁺, Dy³⁺ phosphors have been discussed in detail and compared with the corresponding commercial product. The experimental results indicated that the sample could be synthesized at a relatively lower temperature and had better performance on the above-mentioned properties using the co-precipitation method.     

A new synthetic pathway of Sr2CeO4 phosphor and its characterization

A blue-white emitting Sr₂CeO₄ phosphor was synthesized via a simple sol-gel poly vinyl alcohol (PVA)-complexing process using strontium nitrate and cerium nitrate as raw materials. The samples were characterized by TG/DTA, XRD, FTIR, SEM and photoluminescence spectroscopy. The X-ray diffraction study confirms the structure of the system to be orthorhombic. The emission spectra when excited at 267 nm peaks at ∼470 nm. The emission band is assigned to the energy transfer between the molecular orbital of the ligand and charge transfer state of the Ce⁴⁺ ion. The Commission International de l'Eclairage (CIE) co-ordinates for the Sr₂CeO₄ sample were also calculated.     

Synthesis and Sm/Sm doping effects on photoluminescence properties of Sr4Al14O25

Complete and partial samarium reduction was achieved under strong reducing atmosphere by solid-state and combustion synthesis of Sr_3.96Sm_0.04Al₁₄O₂₅. Dependence of different fluxing agents on the formation of various strontium aluminates was examined. The samples were investigated by X-ray powder diffraction, temperature dependent luminescence decay and photoluminescence measurements. Excitation with UV radiation resulted in sharp and well resolved emission lines of samarium ions. Distinct temperature behavior for Sm²⁺ and Sm³⁺ were detected in the range of 100-500 K. Estimated emission thermal quenching values (TQ_1/2) for divalent samarium were approximately 270 K while for trivalent state around 660 K. Measured luminescence decay values of Sm²⁺ are substantially lower than for Sm³⁺,≈1.7 and ≈2.7 ms, respectively. The spectral feature of Sm²⁺ emission spectrum indicates that dopant occupies low symmetry site in Sr₄Al₁₄O₂₅ compound.     

Intense blue-emitting Ca5Al8O14: Eu phosphor for mercury free lamp

The calcium aluminates doped with Eu ions, Ca₅Al₈O₁₄: Eu, phosphors are prepared by the combustion method. The formation of crystalline aluminates was confirmed by X-ray diffraction pattern. The prepared phosphors were characterized by SEM, TGA, DTA, particle size analyzer and Photoluminescence (PL) techniques. From the UV-excited luminescence spectra it was found that the Eu ions acts as a luminescent centre with luminescence at the blue (λ _max = 470 nm) region due to 4f ⁶5d ¹ → 4f ⁷ transition. The excitation spectra show the broad band at 355 nm wavelength (λ _em = 470 nm). The excitation 355 nm is a mercury free excitation and therefore Ca₅Al₈O₁₄: Eu may be useful for the solid state lighting phosphor in lamp industry.      

Spectral properties of Nd-doped Sr3Ga2Ge4O14 crystal

Neodymium doped strontium gallogermanate crystals were grown successfully by the Bridgman technique. The linear thermal expansion coefficients for the c- and a-axes were measured as 5.8 × 10⁻⁶ °C⁻¹ and 6.5 × 10⁻⁶ °C⁻¹. Absorption spectra, and fluorescence spectra, as well as fluorescence decay curves of Nd³⁺-doped Sr₃Ga₂Ge₄O₁₄ crystal, have been recorded at room temperature and used to calculate the absorption and stimulated emission cross-sections. Based on the Judd-Ofelt theory, three intensity parameters were obtained. The luminescent quantum efficiency of the ⁴F_3/2 level was determined to be approximately 73.8% for this material. Compared with other Nd³⁺-doped laser crystals, Nd³⁺-doped Sr₃Ga₂Ge₄O₁₄ crystal displays special laser properties due to its disorder structure.     

A new self-activated yellow-emitting phosphor Zn2V2O7 for white LED

A new self-activated yellow-emitting Zn₂V₂O₇ phosphor was synthesized by high temperature solid-state reaction. X-ray powder diffraction (XRD) analysis confirmed the sample with monoclinic formation of Zn₂V₂O₇. The excitation and emission spectra indicated the phosphor can be efficiently excited by near ultraviolet (NUV) light in 220–400 nm range and exhibit a bright broad yellow emission with the highest emission intensity at 531 nm. The broad emission band from 400 to 650 nm can be attributed to the charge transfer transition in the VO₄ tetrahedra, which suggests that the phosphor is a promising yellow phosphor applied for white light-emitting diodes (WLED).     

Synthesis and characterization of Sr2CeO4 phosphor: Positive features of sol-gel technique

Nano crystalline powder of Sr₂CeO₄ has been synthesized by sol-gel technique. The luminescence properties of the material were compared with the one synthesized by conventional solid state reaction technique. The homogeneity and uniformity of the particle prepared by this method is much better than that prepared by the solid state reaction technique. This blue emitting phosphor was characterized by X-ray diffraction, scanning electron microscopy images and luminescent measurements. The emission spectrum of the material exhibits a broad band around ∼480 nm. The photoluminescence spectra of the Sr₂CeO₄ reveals that the strong blue emission is assigned to the Ce⁴⁺-O²⁻ charge transfer transition (CTT) of Sr₂CeO₄ and not related to lattice defect. The Commission International de l’Eclairage coordinates are x=0.16 and y=0.25.     

Effects of dopant concentrations on phosphorescence properties of Eu/Dy-doped Sr3MgSi2O8

Long afterglow Sr₃MgSi₂O₈: Eu, Dy phosphor with high brightness was prepared by sintering at high temperature and weak reductive atmosphere. The luminescent properties of this photoluminescent pigment were studied systematically by investigating concentration effects. The analytical results indicated that the main emission peaks appear at 482 nm. The excitation and emission spectra of this phosphor show that both of them are broadband. This is ascribed to the 4f⁷→4f⁶5d¹ transition of Eu²⁺ in the pigment matrix, which is in good agreement with the calculated value of 470 nm, and implies that luminescent centers Eu²⁺ occupy the deca-coordinated Sr²⁺ sites with the host of Sr₃MgSi₂O₈.     

The up-conversion properties of Yb and Er doped Y4Al2O9 phosphors

Er³⁺ doped and Yb³⁺/Er³⁺ co-doped Y₄Al₂O₉ phosphors are prepared by the sol-gel method. The effect of dopant concentration on the structure and up-conversion properties is investigated by X-ray diffraction (XRD) and photoluminescence, respectively. XRD pattern indicates that the sample structure belongs to monoclinic. Under 980 nm excitation, the green and red up-conversion emissions are observed and the emission intensities depended on the Yb³⁺ ion concentration. The green up-conversion emissions decrease with the increase of Yb³⁺ concentration, while red emission increases as Yb³⁺ concentration increases from 0 to 8 at% and then decreases at high Yb³⁺ concentration. The mechanisms of the up-conversion emissions are discussed and results shows that in Er³⁺ and Yb³⁺/Er³⁺ co-doped system, cross-relaxation (CR) and energy transfer (ET) processes play an important role for the green and red up-conversion emissions.     

Luminescent properties of a new green emitting Eu doped CaZrSi2O7 phosphor for WLED applications

CaZrSi₂O₇ (CZS), a modification of the thortveitite family, was prepared as a polycrystalline powder material by the conventional solid-state reaction method. Structural, thermal and photoluminescence (PL) properties of the prepared material were investigated in order to evaluate its potentiality. XRD patterns confirm the monoclinic phase of CaZrSi₂O₇: Eu²⁺ phosphors.. Emissions arising from transitions between the 5d and 4f orbital gaps of Eu²⁺ are manifested in the broadband excitation and emission spectra with major peaks at 363 and 512 nm, respectively. The excitation wavelength matches well with that of the emission of the ultraviolet-light emitting diode (UV-LED). Concentration quenching occurs when the Eu²⁺ concentration is beyond 0.05 and the dipole-dipole interaction was the reason for the corresponding quenching mechanism. The temperature dependence of emission intensity of CZS: Eu²⁺ phosphor was investigated and it showed better thermal stability than the standard YAG: Ce³⁺ phosphor.     

Luminescence studies on the blue-green emitting Sr4Al14O25:Ce phosphor synthesized through solution combustion route

New blue-green emitting Sr₄Al₁₄O₂₅:Ce³⁺ phosphor is reported in this paper. The polycrystalline samples of phosphor were prepared by the conventional solution combustion method and checked for crystallization and phase by X-ray diffraction. Photoluminescence studies reveal the emission at 472 and 511 nm that correspond to the transition between lowest T_2g level of the 5d state to the ²F_5/2 and ²F_7/2 ground state levels of the Ce³⁺. The excitation at 275 nm corresponds to O²⁻→Ce⁴⁺ charge transfer processes to lowest 5d state of Ce ion (T_2g). Phosphorescence decay procedures reveal the existence of slow, medium, and fast component involved in the process. Varying the γ-dose (1-6 Gy), thermoluminescence (TL) measurements were made and glow curve maximum is obtained at 383 K. The phosphor seems to follow a first-order kinetics due to non-shifting T_m property. The T_m-T_stop method followed by the repeated initial rise method is applied to determine the distribution of activation energies and corresponding maximum positions. Chi-square minimization procedures provide the appropriate peak positions and other trapping parameters. From deconvolution results, the activation energies are found to be 0.84 and 1.06 eV, while the frequency factor is of the order of 10¹⁰ and 10¹¹ s⁻¹, respectively.     

Synthesis and characterization of Sr3Al2O6：Eu2＋, Dy3＋ phosphors prepared by sol-gel-combustion processing

A type of red luminescent Sr3Al2O6:Eu2+, Dy3+ phosphor powder is synthesised by sol-gel-combustion processing, with metal nitrates used as the source of metal ions and citric acid as a chelating agent of metal ions. By tracing the formation process of the sol-gel, it is found that it is necessary to reduce the amount of NO3- by dropping ethanol into the solution for forming a stable and homogeneous sol-gel. Thermogravimetric and Differential Scanning Calorimeter Analysis, x-ray diffractionmeter, scanning electron microscopy and photoluminescence spectroscopy are used to investigate the luminescent properties of the as-synthesised Sr3Al2O6:Eu2+, Dy3+. The results reveal that the Sr3Al2O6 crystallises completely when the combustion ash is sintered at 1250 C. The excitation and the emission spectra indicate that the excitation broadband lies mainly in a visible range and the phosphors emit a strong light at 618 nm under the excitation of 472 nm. The afterglow of (Sr0.94Eu0.03Dy0.03)3Al2O6 phosphors sintered at 1250 ℃ lasts for over 1000 s when the excited source is cut off.     

Chemical quenching of positronium in Fe2O3/Al2O3 catalysts

Fe₂O₃/Al₂O₃ catalysts were prepared by solid state reaction method using α-Fe₂O₃ and γ-Al₂O₃ nano powders. The microstructure and surface properties of the catalyst were studied using positron lifetime and coincidence Doppler broadening annihilation radiation measurements. The positron lifetime spectrum shows four components. The two long lifetimes τ₃ and τ₄ are attributed to positronium annihilation in two types of pores distributed inside Al₂O₃ grain and between the grains, respectively. With increasing Fe₂O₃ content from 3 wt% to 40 wt%, the lifetime τ₃ keeps nearly unchanged, while the longest lifetime τ₄ shows decrease from 96 ns to 64 ns. Its intensity decreases drastically from 24% to less than 8%. The Doppler broadening S parameter shows also a continuous decrease. Further analysis of the Doppler broadening spectra reveals a decrease in the p-Ps intensity with increasing Fe₂O₃ content, which rules out the possibility of spin-conversion of positronium. Therefore the decrease of τ₄ is most probably due to the chemical quenching reaction of positronium with Fe ions on the surface of the large pores.