Effect of post-annealing on the properties of copper oxide thin films obtained from the oxidation of evaporated metallic copper

Thin films of copper oxide were obtained through thermal oxidation (100-450 °C) of evaporated metallic copper (Cu) films on glass substrates. The X-ray diffraction (XRD) studies confirmed the cubic Cu phase of the as-deposited films. The films annealed at 100 °C showed mixed Cu-Cu₂O phase, whereas those annealed between 200 and 300 °C showed a single cubic Cu₂O phase. A single monoclinic CuO phase was obtained from the films annealed between 350 and 450 °C. The positive sign of the Hall coefficient confirmed the p-type conductivity in the films with Cu₂O phase. However, a relatively poor crystallinity of these films limited the p-type characteristics. The films with Cu and CuO phases show n-type conductivity. The surface of the as-deposited is smooth (RMS roughness of 1.47 nm) and comprised of uniformly distributed grains (AFM and SEM analysis). The post-annealing is found to be effective on the distribution of grains and their sizes. The poor transmittance of the as-deposited films (<1%) is increased to a maximum of ∼80% (800 nm) on annealing at 200 °C. The direct allowed band gap is varied between 2.03 and 3.02 eV.     

Influence of temperature annealing on optical properties of SrTiO3/BaTiO3 multilayered films on indium tin oxide

We have prepared SrTiO₃/BaTiO₃ thin films with multilayered structures deposited on indium tin oxide (ITO) coated glass by a sol-gel deposition and heating at 300-650 °C. The optical properties were obtained by UV-vis spectroscopy. The films show a high transmittance (approximately 85%) in the visible region. The optical band gap of the films is tunable in the 3.64-4.19 eV range by varying the annealing temperature. An abrupt decrease towards the bulk band gap value is observed at annealing temperatures above 600 °C. The multilayered film annealed at 650 ° C exhibited the maximum refractive index of 2.09-1.91 in the 450-750 nm wavelength range. The XRD and AFM results indicate that the films annealed above 600 ° C are substantially more crystalline than the films prepared at lower temperatures which were used to change their optical band gap and complex refractive index to an extent that depended on the annealing temperature.     

Structural and optical properties of low temperature synthesized Nanostructured BiFeO3 thin films

Nanostructured bismuth ferrite (BiFeO₃) thin films were deposited on glass substrate by the sol-gel process. The as-fired film at 250 °C was found to be amorphous crystallizing to pure rhombohedral phase after annealing at 450 °C for 2 h in air. The XRD pattern shows that the sample is polycrystalline in nature. The average grain size of the film calculated from the XRD data was found to be 16 nm. The as-fired film show high transmittance that decreases after crystallization. The absorption edge of the films was found to be sharper and shifting towards the lower energy as the annealing temperature increases. The optical energy band gaps of the amorphous and crystalline films were found to be 2.63 and 2.31 eV, respectively. The refractive indices of the amorphous and crystalline films were 2.05 and 2.26, respectively.     

Investigation of thermal annealing effects on microstructural and optical properties of HfO2 thin films

In the present paper, we investigate the effect of thermal annealing on optical and microstructural properties of HfO₂ thin films (from 20 to 190 nm) obtained by plasma ion assisted deposition (PIAD). After deposition, the HfO₂ films were annealed in N₂ ambient for 3 h at 300, 350, 450, 500 and 750 °C. Several characterisation techniques including X-ray reflectometry (XRR), X-ray diffraction (XRD), spectroscopic ellipsometry (SE), UV Raman and FTIR were used for the physical characterisation of the as-deposited and annealed HfO₂ thin films. The results indicate that as-deposited PIAD HfO₂ films are mainly amorphous and a transition to a crystalline phase occurs at a temperature higher than 450 °C depending on the layer thickness. The crystalline grains consist of cubic and monoclinic phases already classified in literature but this work provides the first evidence of amorphous-cubic phase transition at a temperature as low as 500 °C. According to SE, XRR and FTIR results, an increase in the interfacial layer thickness can be observed only for high temperature annealing. The SE results show that the amorphous phase of HfO₂ (in 20 nm thick samples) has an optical bandgap of 5.51 eV. Following its transition to a crystalline phase upon annealing at 750 °C, the optical bandgap increases to 5.85 eV.     

Electrochromic and electrochemical properties of amorphous porous nickel hydroxide thin films

Nickel hydroxide films were prepared using the chemical bath deposition (CBD) technique. The amorphous nature of the films was confirmed by X-ray diffraction measurements. X-ray photoelectron spectroscopy (XPS) measurements showed that the films exhibited nickel hydroxide nature. The porosity of the films was studied using optical measurements. The electrochromic properties of the porous nickel hydroxide layers were investigated, using cyclic voltammetry, chronoamperometry, in situ transmittance, UV-vis spectroscopy, and impedance spectroscopy. The change in the optical density (ΔOD) was found to be 0.79 for the as-deposited nickel hydroxide films, whereas it is 0.53 and 0.50 for the films annealed at 150 °C and 200 °C, respectively. The in situ transmittance and chronoamperometry curves revealed that the annealed films had a very fast colouration (t_c < 290 ms) and decolouration (t_b < 130 ms). The measured colouration efficiencies range between 30 and 40 cm²/C. The impedance measurements revealed the faster colouration and good electrochromic properties for the annealed nickel hydroxide films.     

Electrical properties of vacuum-annealed titanium-doped indium oxide films

Titanium-doped indium oxide (ITiO) films were deposited on Corning glass 2000 substrates at room temperature by radio frequency magnetron sputtering followed by vacuum post-annealing. With increasing deposition power, the as-deposited films showed an increasingly crystalline nature. As-deposited amorphous ITiO films obtained at 20 W began to crystallize at the annealing temperature of 155 °C. Although there was no significant change in the crystalline structure of the films, electron mobility improved gradually with further increase in the annealing temperature. After post-annealing at 580 °C, the highest electron mobility of 50 cm² V⁻¹ s⁻¹ was obtained. Compared with the amorphous ITiO films, the ITiO films with a certain degree of crystallinity obtained at high deposition power were less affected by the vacuum annealing. Their electron mobility also improved due to post-annealing, but the increase was insignificant. After post-annealing, the optical transmission of the 325 nm-thick ITiO films showed approximately 80% at wavelengths ranging from 530 to 1100 nm, while the sheet resistance decreased to 10 Ω/sq. This makes them suitable for use as transparent conductive oxide layers of low bandgap solar cells.     

Influence of annealing temperature on the properties of ZnO thin films deposited by thermal evaporation

ZnO thin films were deposited by thermal evaporation of a ZnO powder. The as-deposited films are dark brown, rich zinc and present a low transmittance. Then, these films were annealed in air atmosphere at different temperatures between 100 and 400 °C. Their microstructure and composition were studied using XRD and RBS measurements respectively. By increasing the temperature, it was found that film oxidation starts at 250 °C. XRD peaks related to ZnO appear and peaks related to Zn decrease. At 300 °C, zinc was totally oxidised and the films became totally transparent. The electrical conductivity measurement that were carried out in function of the annealing temperature showed the transition from highly conductive Zn thin film to a lower conductive ZnO thin film. The optical gap (E_g) was deduced from the UV-vis transmittance, and its variation was linked to the formation of ZnO.     

Dielectric behavior of spin-deposited nanocrystalline nickel-zinc ferrite thin films processed by citrate-route

Nanocrystalline nickel-zinc ferrite thin films with the general formula Ni_1−xZn_xFe₂O₄, where x=0.0, 0.2, 0.4 and 0.6 were fabricated via a chemical route known as the citrate precursor route. These films were spin-deposited on indium-tin oxide coated glass, fused quartz and amorphous Si-wafer substrates, and annealed at various temperatures up to 650 °C. The films annealed below 400 °C were found to be X-ray amorphous, while the films annealed at and above 400 °C were polycrystalline exhibiting a single-phase spinel structure. The average grain size of the films evaluated by transmission electron microscopy, is found to be in the range 4-8.5 nm. The room temperature DC resistivity of the films is in the range 10³-10⁷ Ω m. Dielectric constant and dielectric loss were measured in the frequency range 100 Hz-1 MHz. Dielectric constant of the films is found to lie between 25 and 44, while the loss factor is if the order of 10⁻². The higher values of the dielectric constant for films having higher zinc concentration are attributable to the enhanced hopping between Fe²⁺ and Fe³⁺ ions in these samples. The M-H hysteresis measurement of the nickel ferrite thin films annealed at 650 °C showed narrow hysteresis loop—a characteristic of soft ferromagnetic material.     

Influence of annealing temperature on structural and optical properties of ZnO: In thin films prepared by ultrasonic spray technique

Transparent conducting indium doped zinc oxide was deposited on glass substrate by ultrasonic spray method. The In doped ZnO samples with indium concentration of 3 wt.% were deposited at 300, 350 and 400 °C with 2 min of deposition time. The effects of substrate temperature and annealing temperature on the structural, electrical and optical properties were examined. The DRX analyses indicated that In doped ZnO films have polycrystalline nature and hexagonal wurtzite structure with (0 0 2) preferential orientation and the maximum average crystallite size of ZnO: In before and annealed at 500 °C were 45.78 and 55.47 nm at a substrate temperature of 350 °C. The crystallinity of the thin films increased by increasing the substrate temperature up 350 °C, the crystallinity improved after annealing temperature at 500 °C. The film annealed at 500 °C and deposited at 350 °C show lower absorption within the visible wavelength region. The band gap energy increased from E_g = 3.25 to 3.36 eV for without annealing and annealed films at 500 °C, respectively, indicating that the increase in the transition tail width. This is due to the increase in the electrical conductivity of the films after annealing temperature.     

Low-temperature growth of polycrystalline Ge thin film on glass by in situ deposition and ex situ solid-phase crystallization for photovoltaic applications

Poly-crystalline germanium (poly-Ge) thin films have potential for lowering the manufacturing cost of photovoltaic devices especially in tandem solar cells, but high crystalline quality would be required. This work investigates the crystallinity of sputtered Ge thin films on glass prepared by in situ growth and ex situ solid-phase crystallization (SPC). Structural properties of the films were characterized by Raman, X-ray diffraction and ultraviolet-visible reflectance measurements. The results show the transition temperature from amorphous to polycrystalline is between 255 °C and 280 °C for in situ grown poly-Ge films, whereas the transition temperature is between 400 °C and 500 °C for films produced by SPC for a 20 h annealing time. The in situ growth in situ crystallized poly-Ge films at 450 °C exhibit significantly better crystalline quality than those formed by solid-phase crystallization at 600 °C. High crystalline quality at low substrate temperature obtained in this work suggests the poly-Ge films could be promising for use in thin film solar cells on glass.     

Optical constants and thermocoloration of pulsed laser deposited molybdenum oxide thin films

Molybdenum oxide thin films were prepared by pulsed laser deposition. The as-deposited films were dark. Annealing the films in air at 400 °C resulted in transparent films. These films were further annealed in vacuum at 300 and 400 °C to investigate thermocoloration. The structural, chemical, and optical properties of the films were determined. All films were predominantly amorphous. The air-annealed films were nearly stoichiometric. However, after annealing in vacuum at 400 °C, the films became oxygen-deficient. The transmittance of the films progressively decreased as the vacuum-annealing temperature increased, indicating stronger coloration of the films. The optical constants were determined from the transmittance measurements. Both the refractive index and extinction coefficient increased upon vacuum annealing. However, the band gap slightly decreased after vacuum annealing.     

Deposition and characterization of layer-by-layer sputtered AgGaSe2 thin films

Sputtering technique has been used for the deposition of AgGaSe₂ thin films onto soda-lime glass substrates using sequential layer-by-layer deposition of GaSe and Ag thin films. The analysis of energy dispersive analysis of X-ray (EDXA) indicated a Ga-rich composition for as-grown samples and there was a pronounce effect of post-annealing on chemical composition of AgGaSe₂ thin film. X-ray diffraction (XRD) measurements revealed that Ag metallic phase exists in the amorphous AgGaSe₂ structure up to annealing temperature 450 °C and then the structure turned to the single phase AgGaSe₂ with the preferred orientation along (1 1 2) direction with the annealing temperature at 600 °C. The surface morphology of the samples was analyzed by scanning electron microscopy (SEM) measurements. The structural parameters related to chalcopyrite compounds have been calculated. Optical properties of AgGaSe₂ thin films were studied by carrying out transmittance and reflectance measurements in the wavelength range of 325-1100 nm at room temperature. The absorption coefficient and the band gap values for as-grown and annealed samples were evaluated as 1.55 and 1.77 eV, respectively. The crystal-field and spin-orbit splitting levels were resolved. These levels (2.03 and 2.30 eV) were also detected from the photoresponse measurements almost at the same energy values. As a result of the temperature dependent resistivity and mobility measurements in the temperature range of 100-430 K, it was found that the decrease in mobility and the increase in carrier concentration following to the increasing annealing temperature attributed to the structural defects (tetragonal distortion, vacancies and interstitials).     

Crystallization and electrochemical performance of La0.6Sr0.4Co0.2Fe0.8O3 − δ-Ce0.8Gd0.2O1.9 thin film cathodes processed by single solution spray pyrolysis

La_0.6Sr_0.4Co_0.2Fe_0.8O_3 − δ-Ce_0.8Gd_0.2O_1.9 (LSCF-CGO) thin films obtained by spray pyrolysis of a single precursor solution were investigated by XRD, TEM and impedance spectroscopy at annealing temperatures ranging from 500 to 900 °C. Films annealed at 600 °C contained a mixture of amorphous regions and crystalline regions composed of fine crystallites (< 5 nm). Annealing above 600 °C increased the ratio of crystalline to amorphous material, led to the segregation of the films into distinct LSCF and CGO phases, and promoted grain growth. The electrical behavior of the films depended on annealing temperature. At testing temperatures of 400 °C and below, the polarization resistance of films with lower annealing temperatures was larger than the polarization resistance of films with higher annealing temperatures. However, at testing temperatures of 500 °C and above the polarization resistance of films with lower annealing temperatures was equal to or lower than the polarization resistance of films with higher annealing temperatures. This was reflected by the activation energy that decreased with increasing annealing temperature. The varying electrical behavior may be related to microstructural changes that caused bulk diffusion to be the rate-limiting step in films with lower annealing temperatures and oxygen dissociation to be the rate-limiting step in films with higher annealing temperatures.     

Optical and electrical properties of thermally evaporated In49Se48Sn3 films

Nearly stoichiometric thin films of In₄₉Se₄₈Sn₃ were deposited at room temperature, by conventional thermal evaporation of the presynthesized materials, onto precleaned glass substrates. The microstructural studies on the as-deposited and annealed films, using transmission electron microscopy and diffraction (TEMD), revealed that the as-deposited films are amorphous in nature, while those annealed at 498 K are crystalline. The optical properties of the investigated films were determined from the transmittance and reflectance data, in the spectral range 650-2500 nm. An analysis of the optical absorption spectra revealed a non-direct energy gap characterizing the amorphous films, while both allowed and forbidden direct energy gaps characterized the crystalline films. The electrical resistance of the deposited films was carried out during heating and cooling cycles in the temperature range 300-600 K. The results show an irreproducible behavior, while after crystallization the results become reproducible. The analysis of the temperature dependence of the resistance (ln(R) vs. 1000/T) for crystalline films shows two straight lines corresponding to both extrinsic and intrinsic conduction. The room temperature I-V characteristics of the as-deposited films sandwiched between similar Ag metal electrodes shows an ohmic behavior, while non-ohmic behavior attributed to space charge limited conduction has been observed when the films are sandwiched between dissimilar Ag/Al metal electrodes.     

Aluminium-induced crystallization of amorphous silicon films deposited by DC magnetron sputtering on glasses

Amorphous silicon (a-Si) and hydrogenated amorphous silicon (a-Si:H) films were deposited by DC magnetron sputtering technique with argon and hydrogen plasma mixture on Al deposited by thermal evaporation on glass substrates. The a-Si/Al and a-Si:H/Al thin films were annealed at different temperatures ranging from 250 to 550 °C during 4 h in vacuum-sealed bulb. The effects of annealing temperature on optical, structural and morphological properties of as-grown as well as the vacuum-annealed a-Si/Al and a-Si:H/Al thin films are presented in this contribution. The averaged transmittance of a-Si:H/Al film increases upon increasing the annealing temperature. XRD measurements clearly evidence that crystallization is initiated at 450 °C. The number and intensity of diffraction peaks appearing in the diffraction patterns are more important in a-Si:H/Al than that in a-Si/Al layers. Results show that a-Si:H films deposited on Al/glass crystallize above 450 °C and present better crystallization than the a-Si layers. The presence of hydrogen induces an improvement of structural properties of poly-Si prepared by aluminium-induced crystallization (AIC).     

Effects of depositing temperatures on structure and optical properties of TiO2 film deposited by ion beam assisted electron beam evaporation

TiO₂, which is high in refractive index and dielectric constant, plays an important role in the fields of optics and electronics. In this work, TiO₂ films were prepared on glass substrates by the technique of ion beam assisted electron beam evaporation. The films were deposited at 50, 150 and 300 °C, respectively. Then the as-deposited TiO₂ films were annealed at 450 °C for 1 h in vacuum atmosphere. Structures and optical properties of TiO₂ films were characterized by XRD, SEM, ellipsometry and spectrophotometer. As a result, the structure and the refractive index of films were improved by both the annealing and the increasing of the deposition temperature. The UV-vis transmittance spectra also confirmed that the deposition temperature has a significant effect on the transparency of the thin films. The highest transparency over the visible wavelength region of spectra was obtained at the deposition temperature of 300 °C. The allowed direct band gap at the deposition temperature ranging from 50 to 300 °C was estimated to be in the range from 3.81 to 3.92 eV.     

Optimization of annealing conditions of In2S3 thin films deposited by vacuum thermal evaporation

In₂S₃ thin films were grown on glass substrates by means of the vacuum thermal evaporation technique and subsequently thermally annealed in nitrogen and free air atmosphere from 250 to 350 °C for different durations. Experimental parameters have been adjusted in order to optimize the annealing conditions, and to obtain high band gap energy at low deposition temperature, as required for photovoltaic applications. In order to improve our understanding of the influence of the deposition and annealing parameters on device performance, we have investigated our indium sulfide material by X-ray diffraction, energy dispersive X-ray analysis (EDAX), atomic force microscopy (AFM) and spectrophotometry. The optical and structural properties of the films were studied as a function of the annealing temperature and durations. X-ray diffraction analysis shows the initial amorphous nature of deposited In-S thin films and the phase transition into crystalline In₂S₃ upon thermal annealing. Films show a good homogeneity and optical direct band gap energy about 2.2 eV. An annealing temperature of 350 °C during 60 min in air atmosphere were the optimal conditions.     

Characteristics of electron beam evaporated nanocrystalline SnO2 thin films annealed in air

Tin oxide (SnO₂) thin films (about 200 nm thick) have been deposited by electron beam evaporation followed by annealing in air at 350-550 °C for two hours. Optical, electrical and structural properties were studied as a function of annealing temperature. The as-deposited film is amorphous, while all other annealed films are crystalline (having tetragonal structure). XRD suggest that the films are composed of nanoparticles of 5-10 nm. Raman analysis and optical measurements suggest quantum confinement effects that are enhanced with annealing temperature. For instance, Raman peaks of the as-deposited films are blue-shifted as compared to those for bulk SnO₂. Blue shift becomes more pronounced with annealing temperature. Optical band gap energy of amorphous SnO₂ film is 3.61 eV, which increases to about 4.22 eV after crystallization. Two orders of magnitude decrease in resistivity is observed after annealing at 350-400 °C due to structural ordering and crystallization. The resistivity, however, increases slightly with annealing temperature above 400 °C, possibly due to improvement in stoichiometry and associated decrease in charge carrier density.     

Rapid thermal annealing of ITO films

Tin-doped indium oxide (ITO) films with 200 nm thickness were deposited on glass substrates by DC magnetron sputtering at room temperature. And they were annealed by rapid thermal annealing (RTA) method in vacuum ambient at different temperature for 60 s. The effect of annealing temperature on the structural, electrical and optical properties of ITO films was investigated. As the RTA temperature increases, the resistivity of ITO films decreases dramatically, and the transmittance in the visible region increases obviously. The ITO film annealed at 600 °C by RTA in vacuum shows a resistivity of 1.6 × 10⁻⁴ Ω cm and a transmittance of 92%.     

Preferred orientations in nano-gold/silica/silicon interfaces

Gold in contact with silicon substrates Si(1 0 0), Si(1 1 1), and SiO₂ is studied by thermal evaporation and annealing in N₂ using the modified sphere-plate technique. The final orientation distribution of crystalline Au films grown on Si substrate systems that incorporate a native amorphous oxide layer of silica and Au on amorphous silica (SiO₂ glass) substrates is influenced by preferred orientations and twinning. Experimental evidence suggests that the orientation of Au{1 1 1} close packed planes (multiply twinned) was found to be of low-energy as the annealing temperature was increased to 530 °C and 920 °C. Additional orientations were observed for Au{1 0 0} on Si(1 0 0) substrates and Au{1 0 0}, {1 1 0}, and {3 1 1} on SiO₂ substrates. After annealing at 920 °C the size distribution of the gold particles was determined to be within the range of 20-800 nm while the morphology of gold surface appears spherical to faceted in character. These results show similarities to recent findings for smaller nano-size 1D particles, islands and thin Au films on silicon annealed over lower temperature ranges.