通信波段硅基气孔光子晶体的带隙特性及其物理模型研究

用平面波展开法对硅背景下的通信波段不同晶格类型和气孔形状光子晶体的能带结构进行数值计算与分析,提出了相应的物理模型.结果表明:利用光子受限效应和晶格对称性效应可以有效地调控光子带隙.随光子晶体填充率的增加,其约束光子的能力增强,光子带隙在一定范围内展宽且其中心频率蓝移;带隙随晶格对称性增加而变宽.对基元形状和旋转角度的研究发现,光子带隙随基元旋转角度变化具有周期性和对称性,表现出各向异性,由此优化出对应的不同晶格的最佳谐振腔型结构.     

二维正方格子磁性光子晶体的带隙结构

采用平面波展开的方法计算了正方格子二维磁性光子晶体(MPC)的光子带隙结构.散射子的形状分别为：长方形，正方形，六角形和圆形.通过调节磁导率，填充率和散射子的旋转角度，找到了MPC各种结构的最大的绝对带隙宽高比ω_R.研究发现：随着磁导率的增加，MPC绝对带隙中心频率ω_g单调减小，绝对带隙宽度Δω和其宽高比ω_R可能不同时达到最大值.而随着填充率或者散射子旋转角的增加，基本不改变ω_g的大小，各种结构的Δω和ω_R同时达到最大值. 关键词： 磁性光子晶体 光子带隙结构     

Study on complete band gap of two-dimensional photonic crystal with quadrangular rods

The plane wave expansion method (PWM) was employed to study the relation between the photonic band gap (PBG) of 2D triangular lattice photonic crystal (PC) and the shapes of rods and dielectric constant. It is shown that the PBG of PC with quadrangular rods is the widest one, compared with the other case with cross section shapes of triangular, circular and hexagon under the same filling ratio, and a peak value appears when the side length ratio of l_x/l_y is equal to 1.21 approximately to any filling ratio. In the aspect of the effects of dielectric constant, the PBG width does not increase monotonically with the increase permittivity ?₂ of the background material to certain permittivity ?₁ of the quadrangular rods, but has a peak value instead. However, the larger the permittivity ?₁ is, the narrower the band width is and the lower the central frequency is, and the dispersion Δ? = ?₂ − ?₁ is larger also.     

二维三角柱光子晶体的传输特性

利用时域有限差分方法对二维三角介质柱光子晶体的传输特性进行了研究,计算了不同晶格、同一晶格柱体截面面积不同、放置方位角不同、入射波入射方向不同时光子晶体的传输特性。结果表明:光子禁带的宽度与中心频率和晶格结构有很大关系,三角晶格更易形成平坦光子禁带,柱体截面面积大,则形成的禁带较宽,在其他因素相同的条件下柱体放置的方位角在一定范围内对光子禁带有重要影响;对不同入射方向时光子晶体的传输特性的研究结果表明,在低频范围内,入射角对禁带宽度和中心频率没有任何影响,在高频段,透射率随入射角变大而降低。研究结果为实验上制作三角柱光子晶体器件提供了重要的理论依据。     

Photonic nanojet modulation by elliptical microcylinders

The detailed analysis of localized photonic nanojets generated at the shadow side surfaces of dielectric elliptical microcylinder illuminated by a plane wave is reported. We have studied the distribution of the electric energy density within and in the vicinity outside an elliptical microcylinder by using finite-difference time-domain calculation with high resolution. The location of photonic nanojet depends on the radius ratio of the microcylinder. We have further analyzed the effect of the rotation angle of elliptical microcylinder upon the focal length of photonic nanojets. The horizontal and vertical shifts of photonic nanojet can be changed by rotating the rotation angle of elliptical microcylinder. The mechanisms of elliptical microcylinder may supply a new ultra-lens approach to distinguish nanoscale targets such as nanoparticles, optical gratings, and nanoscale surface roughness.     

基于空气环结构的大带隙二维光子晶体的设计

用平面波展开法研究了内介质柱截面为长方形的三角晶格空气环型光子晶体的完全带隙特性。通过调节内介质柱的大小、介电常数、旋转角度以及空气环外半径对完全带隙的影响,找到了一组可以获得大带隙二维光子晶体结构的最佳参数。经优化后得到禁带宽度Δω=0.082(2πca-1)(其中a为晶格常数,c为光速),中心频率ω0=0.401(2πca-1),完全带隙宽度与中心频率的比值达到了20.4%,该结果比圆形内介质柱截面空气环结构的完全带隙大,比普通的空气孔结构的完全带隙增大了37%。     

Effects of structural factors on filtering operation of photonic band gap air bridges with circular and square shape holes

Applying the finite element analysis on the photonic band-gap materials with a cavity at the center for two types of structures, circular and square shape holes with the same cross section, filtering operation of these structures is simulated and compared. Any variations in the structure parameters, such as cavity length, period and hole dimensions, change the transmission peak and frequency bandwidth of these structures. The effects of rotation of square holes and ellipticity of circular holes on filtering operation are studied. Other new structures such as tapered, shortened and non-uniform rotated structures are proposed and filtering characteristics of them are discussed. It is found that, by rotating the square holes around their axis, it is possible to have a blue-shift in the transmission peak wavelength without notable variations in the filter peak and bandwidth. It is concluded that the increase of elliptical holes diameters length causes the decrease of transmission peak and increase of bandwidth with blueshift of the peak wavelength. This shift is larger for one of the elliptical diameter values considered that is along the waveguide length.     

Nonlinear performance in silicon nitride slow light photonic crystal waveguides with elliptical holes

We propose a slow-light photonic crystal waveguide, which uses a combination of circular and elliptical air holes arranged in a hexagonal lattice with the background material of silicon nitride (refractive index n = 2.06). Large value of normalized delay bandwidth product (NDBP = 0.3708) is obtained. We have analyzed nonlinear performance of the structure. With our proposed geometry strong SPM is observed at moderate peak power levels. Proposed photonic crystal waveguide has slow light applications such as reduction in length and power consumption of all-optical and electro-optic switches at optical frequency.     

Photonic band structure in a two-dimensional hexagonal lattice of equilateral triangles

In this paper, the plane wave expansion method is used to calculate the photonic band structure (PBS) for the transverse electric (TE) polarization in a two-dimensional hexagonal lattice composed air holes with cross-sections in the shape of equilateral triangles embedded in a GaAs background. We consider that the dielectric constant of GaAs is dependent on both hydrostatic pressure and temperature. Further, an increase can be observed in the width of the photonic band gap (PBG) while the lengths of the sides of the equilateral triangles are increased. When the pressure increases in the presence of a constant temperature, the dielectric constant of GaAs decreases; further, the PBS exhibits a more noticeable shift toward regions of higher frequencies than that observed while the temperature is increased at a given pressure. We also observed that the PBG obtained by rotating the triangular holes by an angle θ increases when compared against the results obtained for the lattice of holes without performing any rotation. In addition, the results obtained using the supercell technique denote that the position and width of the PBG remain unchanged while removing a triangular hole from the structure, denoting the presence of a defective band within the PBG.     

Vertical cavity surface emitting laser transverse mode and polarization control by elliptical holes photonic crystal

The polarization of traditional photonic crystal (PC) vertical cavity surface emitting laser (VCSEL) is uncontrollable, resulting in the bit error increasing easily. Elliptical hole photonic crystal can control the transverse mode and polarization of VCSEL efficiently. We analyze the far field divergence angle, and birefringence of elliptical hole PC VCSEL. When the ratio of minor axis to major axis b/a=0.7, the PC VCSEL can obtain single mode and polarization. According to the simulation results, we fabricate the device successfully. The output power is 1.7 mW, the far field divergence angle is less than 10°, and the side mode suppression ratio is over 30 dB. The output power in the Y direction is 20 times that in the X direction.     

空气环型二维光子晶体完全带隙特性研究

采用平面波展开法, 系统研究了空气环型二维光子晶体的完全光子带隙随结构参数变化而改变的规律, 并将其与普通的空气孔型和介质柱型二维光子晶体的完全带隙进行了比较. 研究表明: 空气环型二维光子晶体不仅可以获得更宽的完全带隙, 而且, 当介质折射率较低时, 其可以获得普通空气孔型和介质柱型二维光子晶体在低折射率条件下所无法获得的完全带隙. 关键词： 空气环型二维光子晶体 完全带隙 平面波展开法     

外磁场与温度对低温超导光子晶体低频禁带特性的影响

文中用传输矩阵法(TMM)分析了TM波垂直入时,超导光子晶体的低频禁带特性,并讨论了外磁场与温度对禁带的影响.分析结果表明:超导光子晶体存在频率从0开始的低频禁带;当没有外磁场作用时,由于超导中正常态电子的影响,低频禁带的截止频率与温度无关;有外磁场作用时,温度才对截止频率具有可调性.外加恒定磁场时,低频禁带的截止频率随温度升高而减小;而在正常态电子的作用下,温度对处在超导态超导光子晶体禁带截止频率的调节范围相对忽略正常态电子情况下减小.恒温下,通过调节外磁场来控制带隙时,正常态电子的贡献很小可忽略不计;外磁场强度增大禁带截止频率减小.当超导体完全处于正常态时,低频禁带消失.     

大带隙二维三角格子光子晶体结构参数的优化设计

光子晶体结构设计优化是理论研究的一个重要内容.运用平面波展开法对圆柱、方柱及正六边柱构造的二维三角格子光子晶体的禁带进行仿真计算,讨论了介质材料分别为GaAs、Si和Ge情况下,柱子形状、旋转角度、填充比的变化对完全光子禁带的影响.发现:对于二维三角格子光子晶体,相对于介质柱,空气柱更易获得完全光子禁带;而相对于圆柱及...     

大带隙二维光子晶体结构的研究

针对三种常见的介质柱横截面分别为正六边形,正方形和圆形的二维光子晶体,提出了一种增大光子带隙的方法.直角坐标系下,使X方向长度增大p倍,并以原点为中心旋转角度φ,通过调整p和φ来降低结构对称性,使用平面波展开法,对其进行了大量的仿真分析.结果表明,结构改变后的光子晶体具有较大的带隙率.对于三种介质柱的三角晶格结构的光子晶体,最大带隙率能达到12％以上,尤其对于正方柱三角晶格光子晶体,最大带隙率达到15.1％.     

用转移矩阵法数值研究二维正方介质柱光子晶体的传输特性

利用转移矩阵方法对二维正方介质柱光子晶体的传输特性进行了研究,数值计算研究了不同晶格、同一晶格柱体截面面积不同、放置方位角不同时光子晶体的传输特性。数值结果表明光子禁带的宽度与中心频率和晶格结构有很大关系,正方晶格更易形成平坦光子禁带,柱体截面面积大,则形成的禁带较宽,在其他因素相同的条件下柱体放置的方位角对光子禁带有重要影响。数值研究表明在正方介质柱下设计宽平坦光子禁带时,可以首先考虑正方晶格结构,其次设法使柱体截面尽量大一些,最后可通过柱体放置方位角来微调光子禁带的宽度与中心频率以达到设计要求。     

Photonic band-structure effects in soft X-ray spectrum for SBA-15 ordered mesoporous structures

The photonic band gap of SBA-15 ordered mesoporous structure is investigated when used as photonic crystals. The filling fraction has more significant effects on the width and attenuation length of PBG than does the dielectric contrast, whereas the PBG position is strongly dependent on both the filling fraction and dielectric contrast. Since the position of PBG occurs between 30–40 nm and the width is about 4–5 nm, SBA-15 with such a narrow gap is expected to be applied as filters in soft X-ray spectrum.     

一种新型无色散慢光光子晶体薄板波导

利用椭圆形孔替代传统光子晶体薄板波导中邻接波导的最内层两排圆孔构成一种新型低损耗光子晶体薄板光波导.该波导的群速度和群速度色散特性强烈依赖于波导中这两排邻接波导的椭圆孔的特性.借助波导导模展开方法,计算得到波导的能带结构和群指数,并分析了它们与椭圆孔的参数关系.通过优化这些椭圆孔的参数,可以增加光子晶体光波导导模在光锥以下的无固有传输损耗带宽,在2—45 nm 的带宽上实现无色散的常数群速度.这些理论结果将为低损耗低色散慢光波导的设计制造提供理论基础. 关键词： 光子晶体薄板波导 群速度 群指数 群速度色散     

用于短波段发光二极管的二维光子晶体禁带研究

运用平面波展开法(PWE),针对光子晶体在短波长段发光二极管(LED)领域上的应用,主要选择高频禁带模式,研究了4种具有较大应用潜力的二维光子晶体结构,包括正方空气柱结构、三角空气柱结构、正方介质柱结构和三角介质柱结构。在不同晶格常数、占空比(AFF)、柱半径和晶格常数比下,分析了TE模式和TM模式光子禁带的变化。数据分析表明,光子禁带中心波长随AFF增加而变小。相比于其他结构,正方介质柱结构更适于短波段光子晶体LED来提高其出光效率,三角介质柱结构和三角空气柱结构适合用于构造短波段偏振光LED。     

Huge photonic band gaps with strong attenuations resulted from quasi-one-dimensional waveguide networks composed of triangular fundamental loops

In order to design systems generating large photonic band gaps (PBGs), in this paper we construct interesting quasi-one-dimensional (quasi-1D) periodic triangular, diamond, and tetrahedral networks composed of 1D waveguides and triangular fundamental loops. The optical frequency band structures and photonic attenuation behaviors of electromagnetic (EM) waves propagating in the three kinds of one- and two-segment-connected (1SC and 2SC) networks without dissipation are, respectively, investigated and we find that huge PBGs can be produced in the middle of a frequency period and the widths of the largest PBGs can be controlled by adjusting the matching ratio of waveguide length. When the ratio equals 2:1, the width of the hugest PBG resulted in tetrahedral network reaches 0.73 times of a frequency period and is about 1.16 times of the best result reported previously. The average attenuations of the largest PBGs are very strong and increase rapidly with the increment of the number of unit cell. This makes our designed networks with very few unit cells exhibit wonderful PBG features and they can be realized in experiments easily. It may be useful for the designing of optical devices with large PBG and strong attenuation.     

轴向填充率渐变型二维光子晶体

提出了一种轴向填充率渐变型二维三角晶格方空气孔光子晶体,由锥形孔周期性排布而成,在第三维也就是沿空气孔的轴向,空气孔的尺寸连续改变,实现了填充率渐变,填充率f范围为0.700～0.866。经过模拟,在归一化波长(λ/a)的1.43～2.71和3.41～4.00波段,轴向填充率渐变型光子晶体可以将光向填充率小的方向偏折,具有选光功能。采用电化学腐蚀与MEMS工艺相结合的方式,在p型(100)硅基底上制作了轴向填充率渐变型二维三角晶格方孔光子晶体,整个孔的填充率f在0.800～0.866范围内。