Surface plasmon resonance based tapered fiber optic sensor with different taper profiles

A theoretical model for surface plasmon resonance (SPR) based tapered fiber optic sensor is proposed with three different taper profiles, namely, linear, parabolic, and exponential-linear. The effect of taper ratio and taper profiles on the sensor’s performance is studied in detail and the design considerations for significantly enhanced sensitivity are reported. The study shows that the exponential-linear taper profile with high taper ratio provides the best performance. The physical reasons behind sensitivity enhancement due to taper ratio and taper profile are given, wherever required.     

Surface plasmon resonance based fiber optic sensor utilizing indium oxide

A highly sensitive surface plasmon resonance (SPR) based fiber optic sensor with indium oxide (In₂O₃) layer coated on the core of the optical fiber is presented and theoretically analyzed. The sensitivity of the SPR based fiber optic sensor has been evaluated numerically. It is shown that the proposed SPR based fiber optic sensor with In₂O₃ layer possesses high sensitivity in the near infrared region of spectrum, which needs attention to many environmental and security applications and offers more accurate and highly reproducible measurements. In addition, the sensitivity of the SPR based fiber optic sensor decreases with the increase in the thickness of In₂O₃ layer. With sensitivity as high as 4600 nm/RIU, the 170 nm thick In₂O₃ layer based fiber optic SPR sensor demonstrates better performance.     

Fiber optic sensor based on surface plasmon resonance with nanoparticle films

This paper reports on a novel design of a fiber optic surface plasmon resonance (SPR) sensor based on nanoparticle metal film. The performance of the proposed sensor in terms of its signal-to-noise ratio (SNR) and sensitivity under different conditions related to the film with spherical gold nanoparticles embedded in a host material is theoretically analyzed. In particular, the effect of the parameters such as gold particle size, film thickness, and refractive index of host material is studied and the possible explanation, whenever required, is given. The numerical results presented in this paper leads to fulfill the requirement of significant optimization of the important design parameters to achieve a high SNR and sensitivity of a fiber optic SPR sensor with nanoparticle films.     

Theoretical analysis of surface plasmon resonance based fiber optic sensor using indium nitride

An extremely sensitive surface plasmon resonance based fiber optic sensor with indium nitride (InN) layer coated on the core of the optical fiber is theoretically analyzed. The proposed sensor exhibits high sensitivity in the near infrared region of spectrum. The optimized value of thickness of InN layer is found to be 70 nm. Possessing high sensitivity of 4493 nm/RIU, the 70 nm thick InN layer based fiber optic SPR sensor illustrates good sensing behavior.     

准晶体结构光纤表面等离子体共振传感器特性研究

光纤表面等离子体共振传感器在高灵敏度传感和在线实时监测等领域具有重要意义. 设计了一种六重准晶体结构环形通道光纤表面等离子体共振传感器, 基于有限元法对该传感器的传感特性进行了数值模拟. 研究了光纤各结构参量对传感器特性的影响规律. 研究结果表明: 待测液折射率的有效监测范围为1.25–1.331, 最高灵敏度可达26400 nm·RIU^-1, 传感器具有损耗谱杂峰少、探测范围广、灵敏度高、设计灵活性高和光路可弯曲等特点, 在生化检测、公共安全、环境污染监测以及高灵敏度传感等领域具有广泛的应用前景.     

Total dissolved solids estimation with a fiber optic sensor of surface plasmon resonance

In this paper, surface plasmon spectra of ion influence was investigated by using a fabricated fiber optic sensors, then spectrum subtraction of ion and non-ionic solutions were developed for field applications of total dissolved solids (TDS) estimation. We confirmed the SPR spectral difference between seven ionic and three non-ionic liquid samples, that for the same refractive index, resonance wavelength in SPR spectrum is much higher for ionic samples than that in the case of non-ionic ones due to the ions influence. The positive correlation of ion content and extra resonance wavelength shift has been established for TDS estimation in water. With three groups of water samples investigation and field testing, the proposed SPR technique showed a good performance comparable to the conductivity method.     

Numerical study of a highly sensitive surface plasmon resonance sensor based on circular-lattice holey fiber

A new design of surface plasmon resonance (SPR) sensor employing circular-lattice holey fiber to achieve high-sensitivity detection is proposed. The sensing performance of the proposed sensor is numerically investigated and the results indicate that our proposed SPR sensor can be applied to the near-mid infrared detection. Moreover, the maximum wavelength sensitivity of our proposed sensor can reach as high as 1.76×10⁴ nm/refractive index unit (RIU) and the maximum wavelength interrogation resolution can be up to 5.68×10^-6 RIU when the refractive index (RI) of analyte lies in (1.31, 1.36). Thanks to its excellent sensing performance, our proposed SPR sensor will have great potential applications for biological analytes detection, food safety control, bio-molecules detection and so on.     

基于表面等离子体共振的新型超宽带微结构光纤传感器研究

基于表面等离子体共振的微结构光纤传感器具有高灵敏、免标记和实时监控等优点.如今,由于此类传感器广泛应用于食品安全控制、环境检测、生物分子分析物检测等诸多领域而受到大量研究.然而,目前所报道的绝大多数此类传感器只能应用于可见光或近中红外传感.因此,对可应用于中红外传感的表面等离子体共振微结构光纤传感器的研究是一项极具挑战...     

光纤SPR湿敏传感器及其共振光谱特性研究

提出并研制了基于光纤SPR传感探针的新型湿敏传感器。首先研究了光纤SPR传感探针对环境湿度变化的敏感特性,在此基础上提出在光纤SPR传感探针表面增覆不同厚度且具有水分子吸附功能的PVA薄膜来实现环境相对湿度的监测。研究结果表明,增覆双层PVA薄膜的光纤SPR传感探针在高湿区具有较好监测效果,其共振强度对应的相对湿度测量灵敏度达到1.59%/%RH,较光纤SPR探针呈现显著提高。而增覆单层PVA薄膜的光纤SPR传感探针在高湿区共振波长对应的相对湿度监测灵敏度达到2.411nm/%RH。此外所提出的新型光纤SPR湿敏探针在PVA薄膜失效后经过特殊工艺处理仍可重复镀膜使用。     

Measurement of refractive index variation of liquids by surface plasmon resonance and wavelength-modulated heterodyne interferometry

In this study an alternative method based on surface plasmon resonance is proposed for in-situ monitoring of variation in the refractive index of a test sample. A wavelength-modulated light source and an unequal-path-length optical configuration heterodyne interferometer are used to detect the phase difference change, which can then be used to estimate the change in the refractive index of a test sample. The experimental results demonstrate a phase stability of 0.02°. The resolution power of the refractive index is 1.5 × 10^− 6 RIU. This method has several advantages over previously used methods such as simple optical setup, easier operation in real time, and low cost.     

Investigation of the performance of an SPR-based optical fiber sensor using finite-difference time domain

Finite-difference time domain (FDTD) method was used to investigate the performance of surface plasmon resonance (SPR)-based optical fiber sensors. The results show that the performance of the fiber sensor can be optimized by choosing a proper combination of metal layer thickness of 40–60 nm and residual cladding thickness of 400–500 nm. Furthermore, the roughness effect of the gold surface layering the fiber sensor is significant in rough surfaces when sigma rms is greater than 5 nm or correlation length is lower than 100 nm.     

基于表面等离子体共振和定向耦合的D形光子晶体光纤折射率和温度传感器

利用光子晶体光纤结构的灵活性和性能的优越性, 设计了一种基于D形光子晶体光纤的折射率和温度传感器. 在D形光子晶体光纤表面抛磨并镀上金纳米薄膜, 作为表面等离子体共振传感通道用来测量液体折射率; 在包层的一个空气孔中填充温敏液体甲苯, 作为定向耦合通道实现对温度的测量. 进一步的数值计算发现, 基于定向耦合效应的温度传感和基于表面等离子体共振的折射率传感相互独立, D形光子晶体光纤同时进行折射率和温度传感检测. 在各向异性的完美匹配层边界条件下利用全矢量有限元法对该传感器特性进行了数值研究, 发现D形光子晶体光纤的空气孔直径决定了定向耦合吸收峰的中心波长和温度传感的灵敏度, 金薄膜的厚度和D形结构的抛磨深度仅影响表面等离子体共振峰的相对强度. 结果表明: 该传感器在-10–80 ℃的温度范围内具有11.6 nm/℃的温度灵敏度, 在1.34–1.44折射率范围内折射率灵敏度最高可达26000 nm/RIU.     

基于超连续谱的光子晶体光纤表面等离子体效应

提出了利用光子晶体光纤空气孔塌缩技术制作光子晶体光纤表面等离子体共振传感器,构建了空气孔完全塌缩的光子晶体光纤表面等离子体共振传感器模型,并模拟计算了其中的表面等离子体共振效应。制作了全光纤化的波长检测型的光子晶体光纤表面等离子体共振传感器,利用超连续谱光源进行了相关实验。实验结果表明:以空气为待测环境介质时,对应的共振波长为465 nm,与理论计算相符合。     

基于超连续谱的光子晶体光纤表面等离子体效应

 提出了利用光子晶体光纤空气孔塌缩技术制作光子晶体光纤表面等离子体共振传感器,构建了空气孔完全塌缩的光子晶体光纤表面等离子体共振传感器模型,并模拟计算了其中的表面等离子体共振效应。制作了全光纤化的波长检测型的光子晶体光纤表面等离子体共振传感器,利用超连续谱光源进行了相关实验。实验结果表明:以空气为待测环境介质时,对应的共振波长为465 nm,与理论计算相符合。     

Polarization-insensitive surface plasmon resonance sensor by cross-slit metallic periodic arrays

We propose a plasmonic structure to obtain polarization-insensitive localized surface plasmon resonance (LSPR) sensor, which consists of cross-slit metallic periodic arrays embedded in the background material. Numerical simulation illustrates that the mechanism of the LSPR sensor is based on the shift of the Fabry–Perot cavity mode resonance peak in the spectrum as the change of the dielectric material properties for the near fields. And one of the transmission dips of the structure is very sensitive to the background materials; the structure could gain the sensitivity (nm/RIU) more than 500 nm/RIU. Meanwhile, the structure holds great potential to achieve high-performance sensors in practical application due to polarization-insensitive virtue.     

Optical characteristics of subwavelength metallic grating coupled porous film surface plasmon resonance sensor with high sensitivity

A high performance sub-wavelength metallic grating coupled surface plasmon resonance (SWMGCSPR) sensor with metal and porous composite layer is proposed. Rigorous coupled-wave analysis (RCWA) is conducted to prove the design feasibility, characterize the sensor's performance and determine geometric parameters of the structure, which is also employed to compute the electromagnetic (EM) field distributions at the resonant wavelengths. Parameters of sensing platform are optimized to achieve the best performance of the SPR sensor. Obtained results reveal that the proposed structure can excite SPR with negative diffraction order of SWMG. Both wavelength and angular sensitivities are greatly enhanced because surface plasmon wave (SPW) exhibits a large penetration depth which will enlarge the distance of interactions between SP and analytes. The detection sensitivities and quality parameters are estimated to be 700 nm/RIU and 509°/RIU with full width at half maximum (FWHM) less than 2.5 nm using the same optimized structure.     

角度型表面等离子体振荡传感器测量精度提高的新方法

设计了一种基于棱镜的角度型表面等离子体振荡自动测量系统,建立了共轴双旋转台的机械结构,提出了新型扫描的角度测量法,得到表面等离子体振荡谐振曲线。研究了影响系统多次测量一致性的因素,提出了减少采样点、提高单点数据采集次数,并采用三级变步长的测量方法,测量时间缩短至小于原来的1/10,使系统测量精度从1E 4折射率单位提高到了4E-5折射率单位。     

Effect of metamaterial layer on optical surface plasmon resonance sensor

In this paper an optical surface plasmon resonance (SPR) sensor with metamaterial for four and five layered structure is studied. The numerical results presented in this paper leads to a significant properties of metamaterials in sensing field. Computed results of SPR sensors using metamaterial are compared with conventional optical SPR sensors for four and five layered structure. It is seen that wider dynamic range or effective range of measurable refractive index increases when metamaterial layer is used. It is also verified that SPR sensor with metamaterial layer can dramatically enhance the resolution and reduce the reflectivity compared with conventional SPR. Validity of the magnetic field results is proved on the basis of smooth match of the fields in the different layers of the proposed optical SPR sensor.     

Optical fiber SPR biosensor with sandwich assay for the detection of prostate specific antigen

We present a new, sensitive, few mode fiber (FMF) surface plasmon resonance (SPR) biosensor with a sandwich assay for the detection of PSA. The side-polished FMF biosensor does not need a polarizer and a thin high-index overlayer. The optical sensitivity of the SPR sensor was determined as 2.5 × 10⁻⁶ RIU. In the SPR PSA sensor, the SPR signals were amplified by a factor of 6 in average over no secondary antibody, using the sandwich assay. The proposed FMF SPR biosensor has great potential for real-time analysis of immune reaction between biomolecules and the advantages of high-sensitivity and label-free detection.     

数值模拟探针诱导表面等离子体共振耦合纳米光刻

采用有损耗介质和色散介质的二维时域有限差分方法,数值模拟了以光波长514.5nm的p偏振基模高斯光束为入射光源,激发Kretschmann型表面等离子体共振,并通过探针的局域场增强效应实现纳米光刻的新方法——探针诱导表面等离子体共振耦合纳米光刻.分别就探针与记录层的间距以及探针针尖大小,模拟分析了不同情况下探针的局域场增强效应和记录层表面的相对电场强度振幅分布.结果表明,探针工作在接触模式时,探针的局域场增强效应最明显,记录层表面的相对电场强度振幅的对比度最大;当探针针尖距记录层5nm时,针尖下方记录层表面的相对电场强度振幅大于光刻临界值的分布宽度与针尖尺寸相近. 关键词： 纳米光刻 表面等离子体共振 时域有限差分方法