Nonlinear performance in silicon nitride slow light photonic crystal waveguides with elliptical holes

We propose a slow-light photonic crystal waveguide, which uses a combination of circular and elliptical air holes arranged in a hexagonal lattice with the background material of silicon nitride (refractive index n = 2.06). Large value of normalized delay bandwidth product (NDBP = 0.3708) is obtained. We have analyzed nonlinear performance of the structure. With our proposed geometry strong SPM is observed at moderate peak power levels. Proposed photonic crystal waveguide has slow light applications such as reduction in length and power consumption of all-optical and electro-optic switches at optical frequency.     

Well-confined Yb:GdVO4 laser waveguide formed by MeV C ion implantation

The planar waveguide in x-cut Yb:GdVO₄ crystal has been fabricated by 6.0 MeV carbon ion implantation with the fluence of 1 × 10¹⁴ ions/cm² at room temperature. The modes of the waveguide were measured by the prism-coupling method with the wavelength of 633 nm and 1539 nm, respectively. An enhanced ordinary refractive index region was formed with a width of about 4.0 μm beneath the sample surface to act as a waveguide structure. By performing a modal analysis on the observed transverse magnetic polarized modes, it was found that all the transverse magnetic polarized modes can be well-confined inside the waveguide. Strong Yb-related photoluminescence in Yb:GdVO₄ waveguide has been observed at room temperature, which reveals that it exhibits possible applications for integrated active photonic devices.     

Integrated photonic glucose biosensor using a vertically coupled microring resonator in polymers

A photonic glucose biosensor incorporating a vertically coupled polymeric microring resonator was proposed and accomplished. The concentration of a glucose solution was estimated by observing the shift in the resonant wavelength of the resonator. For achieving higher sensitivity the contrast between the effective refractive index of the polymeric waveguide and that of the analyte was minimized. Actually, the effective refractive index of the polymeric waveguide (n = ∼1.390) was substantially close to that (n = ∼1.333) of the fresh solution with no glucose. The fabricated resonator sensor with the free spectral range of 0.66 nm yielded a sensitivity of ∼280 pm/(g/dL), which corresponds to ∼200 nm/RIU (refractive index units) as a refractometric sensor, and provided a detection limit of refractive index change on the order of 10⁻⁵ RIU.     

Characterization of optical planar waveguide in Ce:KNSBN crystal formed by triple-energy helium ion implantation

We report on the optical planar waveguide formation and modal characterization in a Ce:KNSBN crystal by triple helium ion implantation at energies of (2.0, 2.2 and 2.4 MeV) and fluences of (1.5, 1.65 and 2.25) × 10¹⁵ cm⁻². The prism-coupling method is used to investigate the dark-line spectroscopy at wavelength of 632.8 and 1539 nm, respectively. The refractive index profiles of the waveguide are reconstructed by an effective refractive index method. It is found that the ion-beam irradiation creates slight increase of extraordinary index whilst decreases ordinary one in the guide region. The modal analysis shows, at wavelength of 632.8 nm, the fields of one TE and three TM modes are well restricted in the guiding region, which means the formation of non-leaky waveguide in the crystal. The damping coefficients of the waveguide are 0.6 and 1.6 cm⁻¹ for ordinary and extraordinary polarized light at 632.8 nm, respectively.     

The study of electro-optical sensor based on slotted photonic crystal waveguide

A compact and sensitive electro-optical sensor based on slotted photonic crystal waveguide (S-PhCW) is demonstrated. The electro-optical sensor can be realized in photonic crystal (PhC) slabs of silicon in Silicon-on-Insulator (SOI). Nonlinear optical polymer is used as infiltration. By applying three-dimensional finite difference time domain (3D-FDTD), the sensitivity and quality factor of electro-optical sensor with different slotted waveguide width are calculated. In addition, sensitivity and the optical properties such as transmission spectrum and field distributions are compared between electro-optical sensor based on line defect photonic crystal waveguide (W1-PhCW) and that based on slotted photonic crystal waveguide (S-PhCW). Simulation results demonstrate that, compared with electro-optical sensor based on line defect photonic crystal waveguide, the sensitivity and quality factor is improved by 30 times and 6.6 times respectively in sensor based on slotted photonic crystal waveguide. Besides, the proposed PhC sensor devices have the advantage of a compact structure with the potential for monolithic integration with optical-to-electrical on-chip conversion and detection.     

Characterization of optical waveguide in Nd: GdVO4 by triple-energy oxygen ion implantation

We report on the optical planar waveguide formation and modal characterization in Nd: GdVO₄ crystals by triple oxygen ion implantation at energies of (2.4, 3.0, and 3.6 MeV) and fluences of (1.4, 1.4, and 3.1)  × 10¹⁴ions/cm². The prism-coupling method is used to investigate the dark-mode property at wavelength of 632.8 nm. The refractive index profiles of the waveguide are reconstructed by an effective refractive index, n_eff method. The modal analysis shows that the fields of TE modes are well restricted in the guiding region, which means the formation of nonleaky waveguide in the crystal.     

Ultracompact refractive index sensor based on microcavity in the sandwiched photonic crystal waveguide structure

A refractive index (RI) sensor based on the two-dimensional photonic crystal is presented. The sensor is formed by a point-defect resonant cavity in the sandwiched waveguide structure. The transmission spectrums of the sensor with different ambient refractive indices ranging from n = 1.0 to n = 1.6 are calculated. The calculation results show that a change in ambient RI of Δn = 0.001 is apparent, the sensitivity of the sensor (Δλ/Δn) is achieved with 330 nm/RIU (when lattice constant a = 440 nm), where RIU means the refractive index unit; and the transmission efficiency in the RI range of 1.0-1.6 can reach about 40% to 70%, that make the detection of spectrum easy and feasible. The properties of the sensor are analyzed and calculated using the plane-wave expansion (PWE) method and simulated using the finite-difference time-domain (FDTD) method.     

The optical properties of planar waveguides in LiB3O5 crystals formed by Cu implantation

A planar optical waveguide has been formed in a LiB₃O₅ crystal using 6.0 MeV Cu⁺-ions with a dose of 1 × 10¹⁵ ions/cm² at room temperature. Possible propagating modes were measured at a wavelength of 633 nm using the prism-coupling method. The refractive index profiles of the waveguide were reconstructed by an effective refractive index method and the beam propagation method was used to investigate the properties of the propagation modes in the formed waveguide. The results suggest that the fundamental TE₀ and TM₀ modes may be well-confined and propagate a longer distance inside the waveguide. The implantation process was also simulated using the transport of ions in matter code (TRIM), which indicates that the nuclear energy deposition may be the main factor for the refractive index change.     

Fast-response terahertz wave switch based on T-shaped photonic crystal waveguide

We design an ultra-fast terahertz wave switch based on T-shape photonic crystal waveguide. The polymer rod is added in the junction as a point defect, the refractive index of which can be varied by adjusting the external pump laser intensity. The transmission spectrum is calculated by finite-difference time-domain method, which shows that the output energy of the two output ports is closely related to the refractive index of the polymer rod. By continuous wave excitation of the guided mode, the simulation results show that the T-shaped photonic crystal waveguide can flexibly tune the power in two output ports. The tuning rate of the device is about 0.3 ns. These results provide a useful guide and a theoretical basis for the developments of terahertz wave functional components.     

Optimization of photonic bandgap fiber long period grating refractive-index sensors

Long period gratings in low-index contrast solid-core photonic bandgap fibers are a promising platform for fiber-based fluid refractive index sensing with very low detection limits. We provide a comprehensive investigation of the possibilities for refractive index sensing using that principle in a commercial photonic crystal fiber filled with a fluid: using an acoustic grating, we map out the cladding bands, and use this data to optimize a long period grating’s sensitivity. We then implement the optimized long period grating, again using an acoustic grating, and directly measure its sensitivity to refractive index. We demonstrate a sensitivity of 17,900 nm/RIU (6.94 nm/°C) which corresponds to a smallest detectable index change of the fluid of 8.4 × 10⁻⁶.     

Optical sensing characteristics of the photonic crystal fiber filled with magnetic fluid

A novel photonic crystal fiber sensing theory filled with magnetic fluid is proposed based on the change of the MF refractive index under varied magnetic field. The magnetically induced tuning of the magnetic fluid filled PCF propagation properties were investigated by the full-vector finite element method with a perfectly matched layer. Theoretical calculations show that both the effective refractive index and the effective mode area increase vs. the increased magnetic field, and the PCF filled MF with larger d/Λ is more sensitive to magnetic field. When the wavelength λ = 1550 nm, the duty ratio d/Λ = 0.9, d/Λ = 0.6, the effective refractive indexes increase respectively from 1.598279 to 1.617572, from 1.61948 to 1.632484, and the effective mode areas increase respectively from 3.561115 μm² to 7.052360 μm², from 6.167494 μm² to 37.221998 μm² as the magnetic field changes from 25 Oe to 175 Oe. This scheme provides theoretical foundation to use magnetic field to control light in photonic crystal fiber and also offers a potential method for magnetic field sensing based on the TIR-PCF.     

Design of high-Q cavities in 2D photonic crystals air holes filled with polymer

We design novel photonic crystal heterostructure, substituting the air in the holes with materials of refractive index higher than n = 1. This can be achieved by infiltrating the photonic crystal (PC) with polymer. We theoretically investigate the L₂ cavity with two missing holes in the center, where the six holes surrounding the cavity are locally filled with polymer. We show that cavity modes can be differently tuned depending on the size and the position of the first hole adjacent to the cavity. A photonic microcavity with a high Q factor of 5.5 × 10⁶ and a modal volume V of 0.1919 is demonstrated. We demonstrate that the calculated Q factor for the designed cavity increases by a factor of 22 relative to that for a cavity without displaced and reduced air holes, while the modal volume remains almost constant.     

Dispersion optimization of slow light in slotted photonic crystal waveguide by selective air holes infiltration

This work proposed a methodology based on the liquid infiltration of slotted photonic crystal waveguide (SPCW). By choosing the refractive index that infiltrated in the first and second rows of air holes adjacent to the slot, respectively, SPCW was optimized to possess wideband slow light with large group index and low dispersion. The properties of SPCW were numerically simulated by plane wave expansion (PWE) method and finite-difference time-domain (FDTD) method. Simulation results showed that the designed SPCW could control the group index for the same SPCW with the nearly constant group index of 50, 68, 81, 150, and 200 over 7.5 nm, 5.5 nm, 3.1 nm, 1.65 nm, and 1.15 nm. In addition, we demonstrated that this post-fabrication liquid infiltrated technology has the potential for realizing reconfigurable and tunable SPCW, in which the flexible wavelength range of SPCW can also be controlled by different liquid infiltration.     

Characterization of optical waveguide in Nd: LuVO4 crystals by triple-energy oxygen ion implantation

We report on the optical planar waveguide formation and modal characterization in Nd:LuVO₄ crystals by triple-energy O³⁺-ion implantation at energies of 2.4, 3.0, and 3.6 MeV and doses of 1.4, 1.4, and 3.1×10¹⁴ ions/cm², respectively. The prism-coupling method is used to investigate the dark-mode property at a wavelength of 633 nm. The refractive index profiles of the waveguide are reconstructed by the reflectivity calculation method (RCM). The modal analysis shows that the fields of TE modes are well restricted in the guiding region, which indicates the formation of non-leaky waveguide in the crystal.     

Temperature-independent optical fiber Fabry–Perot refractive-index sensor based on hollow-core photonic crystal fiber

A novel optical fiber refractive index (RI) sensor, which is based on an intrinsic Fabry–Perot interferometer (IFPI) formed by a section of hollow-core photonic crystal fiber (HCPCF) and standard single mode fibers (SMF), is proposed. The external refractive index is determined according to the maximum fringe contrast of the interference fringes in the reflective spectrum of the sensor. The RI response performance is demonstrated for the measurement of the different RI solutions. The experimental data agree well with the theoretical results. Also the RI resolution and repeatability of ∼1.5 × 10⁻⁵ and ±0.5% in the linear measurement region, are achieved. In addition, the temperature response is tested from 20 °C to 120 °C, which exhibits excellent thermal stability. Therefore, such an HCPCF-based F–P sensor provides a practical way to measure RI with non-temperature compensation.     

基于耦合介质纳米线的深亚波长局域波导

提出了一种基于耦合介质纳米线的深亚波长局域波导,通过两根紧邻的高折射率介质纳米线的耦合,该波导可以将光场有效束缚在纳米线之间的低折射率纳米缝隙中. 计算模拟的结果表明,该波导的有效模场面积达到Λ²₀/200,比单根纳米线波导小一个数量级,这种深亚波长的模场束缚能力可以与表面等离激元混合波导相比拟. 计算模拟的结果还表明,纳米线可能带有的低折射率氧化膜、低折射率衬底的存在、以及纳米线间尺寸存在的一定差异对于该波导结构的实际应用都不会产生很大 关键词： 介质波导 亚波长局域 表面等离激元波导 纳米线     

Ultrasensitive UV-tunable grating in all-solid photonic bandgap fibers

We study the shift of a long period grating’s resonance wavelength with UV induced refractive index changes in an all-solid photonic bandgap fiber. A long period grating is mechanically imprinted in an all-solid photonic bandgap fiber with Germanium doped silica high-index rods in a lower-index silica background. The index of the high-index rods is modified through UV exposure, and we observe that the long period grating’s resonance shifts with the bandgaps. With a sensitivity of 21,000 nanometers per refractive index unit and a 8.8 nm resonance width changes of refractive index of 3 × 10⁻⁶ are in principle detectable     

Dispersionless slow light by photonic crystal slab waveguide with innermost elliptical air holes

We report a low-loss photonic crystal slab waveguide formed by deforming the innermost circle air holes in the conventional photonic crystal slab waveguide into elliptical ones. We obtain the photonic bands and group index of guided modes in this photonic crystal waveguide by guided-mode expansion method and investigate the dependence of photonic bands and group index of guided modes on the parameters of the innermost elliptical air holes. The group velocity and group velocity dispersion of this waveguide strongly depend on the innermost elliptical air holes. Photonic crystal slab waveguide with the optimum innermost elliptical air holes possesses a wider single mode region below the light line, in which light can easily propagate without intrinsic loss. At the same time, the guided mode supported by this waveguide has nearly constant group velocity and vanishing group velocity dispersion in a 3-5 nm bandwidth.     

The thermo-optical variable optical attenuator based on SOI

A thermo-optical variable optical attenuator was studied based on silicon on insulator (SOI) substrate waveguide. It is composed by the single-mode waveguide, taper waveguide, multi-mode waveguide, and inclined electrode. By adjusting the applied voltage on the inclined electrode it can achieve continuously variable attenuation of the output light. The results we studied show that when the applied voltage is about 4.7 V (the corresponding power is 233 mW), the variation of the waveguide's core temperature is about 33 °C, the refractive index changes more than 5.0 × 10⁻³ and the attenuation will reach 35 dB, and the response time is only 35 μs.     

Temperature effect on the tenability of an eight-channel demultiplexer

A new tunable wavelength division multiplexing (WDM) with a two-dimensional photonic crystal structure using (Multi-layer on InP substrate) is proposed. By tuning the temperature of the photonic crystal, the refractive index of the InP as well as the selected wavelengths can be changed. We show that the designed WDM has the ability to tune eight wavelengths by different values of temperature. The proposed filter has a cross section equal to 16.5 μm × 6.5 μm. The Results of the tenability has been done numerically by using the finite difference time domain (FDTD) method. We can use the proposed structure as temperature sensing device, and in many optical systems.