Analysis of BPSK homodyne receivers based on modified balanced optical phase-locked loop in the presence of non-negligible loop propagation delay

Optical homodyne receivers based on modified balanced optical phase-locked loop is analyzed taking into account loop propagation delay. This modified loop contains all the components of a standard BOPLL in conjunction of an additional phase modulator. This modified loop offers a much improved tracking performance and also shows good improvements in the reduction performance over previously reported methods, like, relaxed line-width requirement and improved lock-in range. This study for the first time shows the imperfect-phase-recovery-induced power penalty as a function of laser line-width with the optimum phase deviations in the presence of non-negligible loop propagation delay. It is found that in order to maintain a 10⁻¹⁰ BER system performance with ξ = 1, R = 1 A/W, P_R = −53 dBm, Δυ = 1 MHz, phase modulator sensitivity K_PM = 10 rad/V and 10° phase deviation between the two transmitted bits, the loop delay must be kept below 3 ns. Further, the required line-width with the non-negligible loop delay time is evaluated and found to be (2.1 × 10⁻³)/τ, where τ (s) is the loop delay. This number corresponds to BER = 10⁻¹⁰, imperfect phase recovery power penalty of 1 dB and phase modulator sensitivity K_PM = 20 rad/V.     

Illumination dependence of I-V and C-V characterization of Au/InSb/InP(1 0 0) Schottky structure

The effects of surface preparation and illumination on electric parameters of Au/InSb/InP(100) Schottky diode were investigated, in the later diode InSb forms a fine restructuration layer allowing to block In atoms migration to surface. In order to study the electric characteristics under illumination, we make use of an He-Ne laser of 1 mW power and 632.8 nm wavelength. The current-voltage I(V_G), the capacitance-voltage C(V_G) measurements were plotted and analysed. The saturation current I_s, the serial resistance R_s and the mean ideality factor n are, respectively, equal to 2.03 × 10⁻⁵ A, 85 Ω, 1.7 under dark and to 3.97 × 10⁻⁵ A, 67 Ω, 1.59 under illumination. The analysis of I(V_G) and C(V_G) characteristics allows us to determine the mean interfacial state density N_ss and the transmission coefficient θ_n equal, respectively, to 4.33 × 10¹² eV⁻¹ cm⁻², 4.08 × 10⁻³ under dark and 3.79 × 10¹² eV⁻¹ cm⁻² and 5.65 × 10⁻³ under illumination. The deep discrete donor levels presence in the semiconductor bulk under dark and under illumination are responsible for the non-linearity of the C⁻²(V_G) characteristic.     

Nonlinear optical properties of periodic gold nanoparticle arrays

Periodic Au nanoparticle arrays were fabricated on silica substrates using nanosphere lithography. The identical single-layer masks were prepared by self-assembly of polystyrene nanospheres with radius R = 350 nm. The structural characterization of nanosphere masks and periodic particle arrays was investigated by atomic force microscopy. The nonlinear optical properties of the Au nanoparticle arrays were determined using a single beam z-scan method at a wavelength of 532 nm with laser duration of 55 ps. The results show that periodic Au nanoparticle arrays exhibit a fast third-order nonlinear optical response with the nonlinear refractive index and nonlinear absorption coefficient being n₂ = 6.09 × 10⁻⁶ cm²/kW and β = −1.87 × 10⁻⁶ m/W, respectively.     

Spectra and intensity parameters of Tm ion in YAlO3 crystal

High quality Tm-doped YAlO₃ (Tm:YAlO₃) single crystals were obtained along crystallographic b-axis by the Czochralski technique. Optical absorption and fluorescence spectra for Tm³⁺ in YAlO₃ crystals were investigated at room temperature. Based on Judd-Ofelt approach, the intensity parameters Ω_t (t = 2, 4, 6) of Tm:YAlO₃ were calculated to be Ω₂ = 0.93 × 10⁻²⁰  cm², Ω₄ = 2.23 × 10⁻²⁰ cm², and Ω₆ = 1.12 × 10⁻²⁰ cm². The spectral parameters such as experimental and theoretical oscillator strengths, radiative transition probabilities, radiative lifetime and the fluorescence branching ratio were also obtained. All results indicate that Tm:YAlO₃ is a potential candidate for compact, efficient mid-infrared lasers with laser diode pumping.     

Wide bandwidth phase-locked diode laser with an intra-cavity electro-optic modulator

Two extended cavity laser diodes are phase-locked, thanks to an intra-cavity electro-optical modulator. The phase-locked loop bandwidth is on the order of 10 MHz, which is about twice larger than when the feedback correction is applied on the laser current. The phase noise reaches −120 dBrad²/Hz at 10 kHz. This new scheme reduces the residual laser phase noise, which constitutes one of the dominant contributions in the sensitivity limit of atom interferometers using two-photon transitions.     

Femtosecond Z-scan measurement of third-order optical nonlinearities in anatase TiO2 thin films

Anatase phase TiO₂ films have been grown on fused silica substrate by pulsed laser deposition technique at substrate temperature of 750 °C under the oxygen pressure of 5 Pa. From the transmission spectra, the optical band gap and linear refractive index of the TiO₂ films were determined. The third-order optical nonlinearities of the films were measured by Z-scan method using a femtosecond laser (50 fs) at the wavelength of 800 nm. The real and imaginary parts of third-order nonlinear susceptibility χ⁽³⁾ were determined to be −7.1 × 10⁻¹¹esu and −4.42 × 10⁻¹²esu, respectively. The figure of merit, T, defined by T=βλ/n₂, was calculated to be 0.8, which meets the requirement of all-optical switching devices. The results show that the anatase TiO₂ films have great potential applications for nonlinear optical devices.     

Upconversion luminescence and optical power limiting effect based on two- and three-photon absorption processes of ZnO crystal

Near-infrared to UV and visible upconversion luminescence was observed in single-crystalline ZnO under an 800 nm infrared femtosecond laser irradiation. The optical properties of the crystal reveal that the UV and VIS emission band are due to the exciton transition (D₀X) bound to neutral donors and the deep luminescent centers in ZnO, respectively. The relationship between the upconversion luminescence intensity and the pump power of the femtosecond laser reveals that the UV emission belongs to three-photon sequential band-to-band excitation and the VIS emission belongs to two-photon simultaneous defect-absorption induced luminescence. A saturation phenomenon and polarization-dependent effect are also observed in the upconversion process of ZnO. A very good optical power limiting performance at 800 nm has been demonstrated. The two- and three-photon absorption coefficients of ZnO crystal were measured to be 0.2018 cm GW⁻¹ and 7.102 × 10⁻³ cm³ GW⁻², respectively. The two- and three-photon cross sections were calculated to be 1.189 × 10⁻⁵¹ cm⁴ s and 1.040 × 10⁻⁸⁰  cm⁶ s², respectively.     

Electrical transport properties of CaMnO3 thermoelectric compound: a theoretical study

The electrical transport coefficients of anti-ferromagnetic CaMnO₃ have been investigated by density functional theory calculation within generalized gradient approximation. The calculated transport coefficients exhibit the anisotropic nature, in agreement with its electronic states. The transport property results reveal the stronger carrier transport along the O1–Mn–O1 plane within the O–Mn–O octahedron, indicating that the Mnd and O1p orbitals are mainly responsible for electrical transport. The maximum power factor values as a function of relaxation time reach 8.4×10²³ Wm⁻¹ K⁻² s⁻¹, 7.9×10²³Wm⁻¹ K⁻² s⁻¹ and 4.9×10²³ Wm⁻¹ K⁻² s⁻¹ within c, a and b direction, respectively. The dimensionless figure of merit ZTxx, ZTyy as well as ZTzz is estimated with 1.28, 0.8 and 1.37 at 1000 K, respectively.     

ICLAS of weak transitions of water between 11 300 and 12 850 cm: Comparison with FTS databases

Very weak water vapor absorption lines have been investigated by intracavity laser absorption spectroscopy (ICLAS) in the 11 335-11 947 and 12 336-12 843 cm⁻¹ spectral regions dominated by the ν₁ + 3ν₂ + ν₃ and ν₂ + 3ν₃ bands, respectively. A detectivity on the order of α_min ∼ 10⁻⁹ cm⁻¹ was achieved with an ICLAS spectrometer based on a Ti: Sapphire laser. It allowed detecting transitions with an intensity down to 5 × 10⁻²⁸ cm/molecule which is about 10 times lower than the weakest line intensities previously detected in the considered region. A line list corresponding to 1281 transitions with intensity lower than 5 × 10⁻²⁶ cm/molecule has been generated. A detailed comparison with the line lists provided by the HITRAN database and by recent investigations by Fourier transform spectroscopy associated with very long multi pass cell is presented. The rovibrational assignment performed on the basis of the ab initio calculations of Schwenke and Partridge, has allowed for determining 176 new energy levels belonging to a total of 16 vibrational states.     

Doppler-limited CW infrared cavity ringdown spectroscopy of the ν1+ν3 OH + CH stretch combination band of jet-cooled methanol

A high resolution cavity ringdown spectrometer (CRDS) has been constructed using a 1.5 μm continuous-wave external-cavity tunable diode laser, a mode-matched near-confocal ringdown cavity, and 2 cm pulsed slit jet. Without signal averaging, the RMS noise in the absorption signal is 1.7 × 10⁻⁹ cm⁻¹. The rotationally resolved overtone spectrum of the OH(ν₁) + CH(ν₃) stretch combination band of methanol between 6510 and 6550 cm⁻¹ has been observed for J^′=0-8 and K^′=0-3 at sub-Doppler resolution. In total, 418 lines are assigned and global fits yield molecular torsion-rotation parameters for the upper state. Four K^′-localized perturbations are analyzed and the pattern of residuals is discussed.     

Propagation regimes of intense circularly polarized laser beam in magnetoactive plasma

This paper presents an analytical and numerical investigation of an intense circularly polarized wave propagating along the static magnetic field parallel to oscillating magnetic field in magnetoactive plasma. In the relativistic regime such a magnetic field is created by pulse itself. The authors have studied different regimes of propagation with relativistic electron mass effect for magnetized plasma. An appropriate expression for dielectric tensor in relativistic magnetoactive plasma has been evaluated under paraxial theory. Two modes of propagation as extraordinary and ordinary exist; because of the relativistic effect, ultra-strong magnetic fields are generated which significantly influence the propagation of laser beam in plasma. The nature of propagation is characterized through the critical-divider curves in the normalized beam width with power plane For given values of normalized density (ω_p/ω) and magnetic field (ω_c/ω) the regions are namely steady divergence (SD), oscillatory divergence (OD) and self-focusing (SF). Numerical computations are performed for typical parameters of relativistic laser-plasma interaction: magnetic field B = 10-100 MG; intensity I = 10¹⁶ to 10²⁰ W/cm²; laser frequency ω = 1.1 × 10¹⁵ s⁻¹; cyclotron frequency ω_c = 1.7 × 10¹³ s⁻¹; electron density n_e = 2.18 × 10²⁰ cm⁻³. From the calculations, we confirm that a circularly polarized wave can propagate in different regimes for both the modes, and explicitly indicating enhancement in wave propagation, beam focusing/self-guiding and penetration of E-mode in presence of magnetic field.     

Structural and ac electrical properties of a newly synthesized single phase rare earth double perovskite oxide: Ba2CeNbO6

A single phase rare earth double perovskite oxide Ba₂CeNbO₆ (BCN) is synthesized by solid-state reaction technique for the first time. The X-ray diffraction pattern of the sample at room temperature shows monoclinic structure, with the lattice parameters, a=5.9763 Å, b=5.975 Å and c=8.48 Å and β=90.04°. Impedance spectroscopy is used to study the ac electrical behavior of this material as a function of frequency (10²-10⁶ Hz) at various temperatures (30-450 °C). A relaxation is observed in the entire temperature range. Conduction mechanism is investigated by fitting the complex impedance data to Cole-Cole equation. Complex impedance plane plots show only one semicircular arc, indicating only the grain contribution of dielectric relaxation. The scaling behavior of imaginary part of electric modulus (M″) and imaginary part of electrical impedance (Z″) suggests that the relaxation describes the same mechanism at various temperatures. The frequency dependence of conductivity is interpreted in terms of the jump relaxation model and is fitted to Jonscher's power law. The values of dc conductivities extracted from the Jonscher power law varies from 2.79×10⁻⁷ to 3.5×10⁻⁵ Sm⁻¹ with the increase in temperature from 100 to 450 °C. The activation energies (0.37 eV) extracted from M″(ω) and Z″(ω) peaks are found to follow the Arrhenius law.     

Preparation of five-layered Si/SixGe1−x nano-films by RF helicon magnetron sputtering

Five-layered Si/Si_xGe_1−x films on Si(1 0 0) substrate with single-layer thickness of 30 nm, 10 nm and 5 nm, respectively were prepared by RF helicon magnetron sputtering with dual targets of Si and Ge to investigate the feasibility of an industrial fabrication method on multi-stacked superlattice structure for thin-film thermoelectric applications. The fine periodic structure is confirmed in the samples except for the case of 5 nm in single-layer thickness. Fine crystalline Si_xGe_1−x layer is obtained from 700 °C in substrate temperature, while higher than 700 °C is required for Si good layer. The composition ratio (x) in Si_xGe_1−x is varied depending on the applied power to Si and Ge targets. Typical power ratio to obtain x = 0.83 was 7:3, Hall coefficient, p-type carrier concentration, sheet carrier concentration and mobility measured for the sample composed of five layers of Si (10 nm)/Si_0.82Ge_0.18 (10 nm) are 2.55 × 10⁶ /°C, 2.56 × 10¹² cm⁻³, 1.28 × 10⁷ cm⁻², and 15.8 cm⁻²/(V s), respectively.     

Direct observation of the D′ 2g(P2)-A′ Π(2u) system for Cl2 by laser induced fluorescence spectroscopy: Determination of the absolute position of the A′ state

In a discharged supersonic jet of Cl₂, transitions of the D′ 2_g(³P₂)-A′ ³Π(2_u) system for ³⁵Cl₂ were observed directly by laser induced fluorescence spectroscopy. By a discharge in Cl₂, the Cl₂ molecules were populated into the A′ state, which is a metastable and optically forbidden state, from the state. An ultraviolet laser radiation excites the molecules to the D′ ion-pair state. A set of Dunham parameters for the A′ state is determined from a global least-squares fitting for 59 vibronic bands with v″ = 0-7. In the fitting, the previously reported data, T(v) and B(v) for the v = 14 and 15 bands of the A′ state [T. Ishiwata, A. Ishiguro, K. Obi, J. Mol. Spectrosc. 147 (1991) 300-320], were included. Y₀₀ = 57295.723(5) cm⁻¹ of the D′ state [J.-H. Si, T. Ishiwata, K. Obi, J. Mol. Spectrosc. 147 (1991) 334-345] was also included in the global fitting in order to determine the absolute position of the A′ state. The determined parameters of the A′ state are Y₀₀ = 17171.506(14), Y₁₀ = 255.915(85), Y₂₀ = −4.465(70), Y₃₀ = −8.7(23) × 10⁻², Y₄₀ = 6.3(35) × 10⁻³, Y₅₀ = −4.9(26) × 10⁻⁴, Y₆₀ = 1.43(69) × 10⁻⁵, Y₀₁ = 0.16282(15), Y₁₁ = −2.363(68) × 10⁻³, Y₂₁ = −5.01(93) × 10⁻⁵, and Y₃₁ = −3.01(36) × 10⁻⁶ (in cm⁻¹ and one standard deviations of the fit in parentheses). The absolute position of the A′ state is determined with good accuracy.     

Magnetic and electrical properties of amorphous Ge1−xCrx thin films grown by low temperature vapor deposition

Amorphous Ge_1−xCr_x thin films are deposited on (1 0 0)Si by using a thermal evaporator. Amorphous phase is obtained when Cr concentration is lower than 30.7 at%. The electrical resistivities are 1.89×10⁻³–0.96×10² Ω cm at 300 K, and decrease with Cr concentration. The Ge_1−xCr_x thin films are p-type. The hole concentrations are 5×10¹⁶–7×10²¹ cm⁻³ at 300 K, and increase with Cr concentration. Magnetizations are 7.60–1.57 emu/cm³ at 5 K in the applied field of 2 T. The magnetizations decrease with Cr concentration and temperature. Magnetization characteristics show that the Ge_1−xCr_x thin films are paramagnetic.     

Determination of sibutramine with a new sensor based on luminol electrochemiluminescence

A flow injection electrochemiluminescence (FI-ECL) analysis method for the determination of sibutramine in the presence of luminol was studied under conventional cyclic voltammetry in alkaline Na₂CO₃-NaHCO₃ buffer solution (pH 8.0-12.0). This method is based on the enhanced ECL of luminol-sibutramine. Meanwhile, in order to overcome the drawbacks of conventional cells, a FI cell was designed, which is reusable and has a great improvement in sensitivity and selectivity for ECL analysis. Under the optimal experimental conditions, the enhanced ECL intensity was linearly related to the concentration of sibutramine in the range 1.0×10⁻⁸-1.0×10⁻⁶ g mL⁻¹ with a detection limit of 2.48×10⁻⁹ g mL⁻¹ and a correlation coefficient (R) of 0.9995. The relative standard deviation (RSD) for 1.0×10⁻⁷ g mL⁻¹ samples was 2.1% (n=11). The possible mechanism discussed. The proposed FI-ECL method has been successfully applied to the determination of sibutramine in diet pill samples.     

Growth and spectroscopic characterization of Er: Sr3Y(BO3)3 crystal

This paper reports the growth and spectroscopic characterization of Er³⁺:Sr₃Y(BO₃)₃ crystal. Er³⁺:Sr₃Y(BO₃)₃ crystal with dimensions up to ∅20×35 mm³ has been grown by Czochralski method. The polarized spectroscopic properties of Er³⁺:Sr₃Y(BO₃)₃ crystal were investigated. Based on the Judd-Ofelt theory, the effective intensity parameters Ω_t were obtained: Ω₂=1.71×10⁻²⁰ cm², Ω₄=1.39×10⁻²⁰ cm², Ω₆=0.74×10⁻²⁰ cm² for π-polarization, and Ω₂=1.77×10⁻²⁰ cm², Ω₄=1.44×10⁻²⁰ cm², Ω₆=0.65×10⁻²⁰ cm² for σ-polarization. The emission cross-section σ_em was calculated to be 4.75×10⁻²¹ cm² for π-polarization at 1536 nm and 6.30×10⁻²¹ cm² for σ-polarization at 1537 nm. The investigated results showed that Er³⁺:Sr₃Y(BO₃)₃ crystal may be regarded as a potential laser host material for 1.55 μm IR solid-state lasers.     

Experimental determination of solid-liquid interfacial energy for solid Sn in the Sn-Mg system

The equilibrated grain boundary groove shapes for solid Sn in equilibrium with the Sn-9 at.% Mg eutectic liquid were directly observed annealing a sample at the eutectic temperature for about 5 days with a radial heat flow apparatus. The thermal conductivities of the solid phase, κ_S, and the liquid phase, κ_L, for the groove shapes were measured. From the observed grain boundary groove shapes, the Gibbs-Thomson coefficient, the solid-liquid interfacial energy and grain boundary energy for solid Sn in equilibrium with the Sn-9 at.% Mg eutectic liquid have been determined to be (7.35 ± 0.36) × 10⁻⁸ Km, (136.41 ± 13.64) × 10⁻³ J m⁻² and (230.95 ± 25.40) × 10⁻³ J m⁻², respectively.     

Synthesis and utilization of chitin-humic acid hybrid as sorbent for Cr(III)

New types of hybrid material have been synthesized by using four different methods of immobilization of humic acid (HA) on chitin. The most stable hybrid material toward the change of medium acidity was then utilized as sorbent for Cr(III).The HA was extracted from peat soil of Gambut District, South Kalimantan, Indonesia, using the recommended procedure of International Humic Substances Society (IHSS), while the chitin was isolated from crab shell waste through deproteination using 3.5% (w/v) NaOH and followed by removal of inorganic impurities using 1 M HCl. The four methods of immobilization of HA on chitin were (i) Method A: chitin powder (4 g) was gently poured into the stirred solution of 0.4 g HA in 40 mL of 0.01 M NaOH. After overnight stirring, the solid was separated, washed with water, and dried in oven at 70 °C. (ii) Method B: gelatinous chitin (40 g) in 250 mL of 0.5 M HCl was reacted with HA (4 g) in 500 mL of 0.5 M NaOH and aged for 24 h. The product was washed with water and dried. (iii) Method C: HA powder (0.5 g) was mixed with the stirred gel of chitin (2.5 g) in 60 mL of CaCl₂ saturated methanol and the mixture was then washed with the mixed solution of 25 mL of 2 M sodium citrate and ethylene glycol 1:1. The solid was separated, washed with water, and dried. (iv) Method D: the solution of HA (0.056 g) in 10 mL of 0.01 M NaOH was reacted with the gel of chitin (0.2 g) in 10 mL of CaCl₂ saturated methanol. After 24 h stirring, the solid was separated from the reaction medium, washed with the mixed solution of 2 M sodium citrate and ethylene glycol 1:1, and followed by washing with water and drying. Parameters investigated in this study consisted of the stability test of the immobilized HA, as well as the rate constant (k₁), capacity (b), and energy (E) of sorption as well as the rate constant of desorption (k₋₁). The k₁ and k₋₁ were determined according to a kinetic model of first order sorption reaching equilibrium, while the b and E were determined according to the Langmuir isotherm model.Compared to HA, Methods, A, C, and D; Method B produced the most stable immobilization of HA on chitin. The hybrid material (Chitin-HA) synthesized through Method B was stable in the acidity range that equivalent to pH 2.0-11.0. At the acidity giving maximum sorption, i.e. pH 5, the presence of immobilized HA on the Chitin-HA enhanced more than three times the k₁ and k₋₁, i.e. from 0.057 min⁻¹ and 8.51 × 10⁻⁴ (min⁻¹) (mol/L) for chitin to 0.183 min⁻¹ and 3.27 × 10⁻³ (min⁻¹) (mol/L) for the Chitin-HA. On the contrary, the presence of HA on Chitin-HA only gave small increase on b and small decrease on E. The values of b and E for Cr(III) on chitin were 1.45 × 10⁻² mol/g and 23.12 kJ/mol, respectively, while those on Chitin-HA were 1.78 × 10⁻² mol/g and 19.95 kJ/mol, respectively.     

Third-order nonlinear optical studies of new anthraquinone derivatives

Four new donor-acceptor-donor anthraquinone derivatives were synthesized and characterized by UV, IR, ¹H NMR and elemental analysis. Their off-resonant third-order nonlinear optical properties were measured using femtosecond laser and degenerate four-wave mixing technique. The third-order nonlinear optical susceptibilities χ⁽³⁾ were 3.36-3.76 × 10⁻¹³ esu. The nonlinear refractive indexes n₂ were 6.19-6.91 × 10⁻¹² esu. The second-order hyperpolarizabilities γ of the molecules were 3.36-3.76 × 10⁻³¹ esu. The response times were 101-115 fs. The results show that these compounds have potential nonlinear optical applications.