A new BOD estimation method employing a double-mediator system by ferricyanide and menadione using the eukaryote Saccharomyces cerevisiae

A new biochemical oxygen demand (BOD) sensing method employing a double-mediator (DM) system coupled with ferricyanide and a lipophilic mediator, menadione and the eukaryote Saccharomyces cerevisiae has been developed. In this study, a stirred micro-batch-type microbial sensor with a 560 μL volume and a two-electrode system was used. The chronamperometric response of this sensor had a linear response between 1 μM and 10 mM hexacyanoferrate(II) (r² = 0.9995, 14 points, n = 3, average of relative standard deviation and R.S.D._av = 1.3%). Next, the optimum conditions for BOD estimation by the DM system (BOD_DM) were investigated and the findings revealed that the concentration of ethanol, used to dissolve menadione, influenced the sensor response and a relationship between the sensor output and glucose glutamic acid concentration was obtained over a range of 6.6-220 mg O₂ L⁻¹ (five points, n = 3, R.S.D._av 6.6%) when using a reaction mixture incubated for 15 min. Subsequently, the characterization of this sensor was studied. The sensor responses to 14 pure organic substances were compared with the conventional BOD₅ method and other biosensor methods. Similar results with the BOD biosensor system using Trichosporon cutaneum were obtained. In addition, the influence of chloride ion, artificial seawater and heavy metal ions on the sensor response was investigated. A slight influence of 20.0 g L⁻¹ chloride ion and artificial seawater (18.4 g L⁻¹ Cl⁻) was observed. Thus, the possibility of BOD determination for seawater was suggested in this study. In addition, no influence of the heavy metal ions (1.0 mg L⁻¹ Fe³⁺, Cu²⁺, Mn²⁺, Cr³⁺ and Zn²⁺) was observed. Real sample measurements using both river water and seawater were performed and compared with those obtained from the BOD₅ method. Finally, stable responses were obtained for 14 days when the yeast suspension was stored at 4 °C (response reduction, 93%; R.S.D. for 6 testing days, 9.1%).     

A novel approach based on ferricyanide-mediator immobilized in an ion-exchangeable biosensing film for the determination of biochemical oxygen demand

A novel biochemical oxygen demand (BOD) sensing method employing a ferricyanide (FC) mediator immobilized in an ion-exchangeable polysiloxane was developed. The ion-exchangeable polysiloxane containing alkylammonium groups (PAPS-Cl) was synthesized by sol-gel reaction of 3-(aminopropyl)trimethoxysilane (APTMOS) catalyzed by hydrochloric acid. FC was combined in PAPS-Cl via ion-association and the product was labeled as PAPS-FC, which was employed for a modified glassy carbon electrode. The apparent diffusion coefficient (D_app) of FC on the modified glassy carbon electrode was 9.8 × 10⁻¹¹ cm² s⁻¹. In a three-electrode system, a linear relationship between the anodic current responses and glucose/glutamate (GGA) concentration was obtained up to 40 mg O₂ L⁻¹ (r = 0.994) when the reaction mixture was incubated for 30 min. Single sensor and piece-to-piece reproducibility were less than 3.8 and 7.7%, respectively. The effects of dissolved oxygen, pH, temperature and co-existing substances on the BOD responses were studied. The sensor responses to nine pure organic substances were compared with the conventional BOD₅ method and other biosensor methods. Detection results of seawater samples were compared with those obtained from the BOD₅ method and showed a good correlation (r = 0.988).     

A chemiluminescence biochemical oxygen demand measuring method

A new chemiluminescence biochemical oxygen demand (BOD_CL) determining method was studied by employing redox reaction between quinone and Baker's yeast. The measurement was carried out by utilizing luminol chemiluminescence (CL) reaction catalyzed by ferricyanide with oxidized quinone of menadione, and Saccharomyces cerevisiae using a batch-type luminometer. In this study, dimethyl sulfoxide was used as a solvent for menadione. After optimization of the measuring conditions, the CL response to hydrogen peroxide in the incubation mixture had a linear response between 0.1 and 100 μM H₂O₂ (r² = 0.9999, 8 points, n = 3, average of relative standard deviation; R.S.D._av = 4.22%). Next, a practical relationship between the BOD_CL response and the glucose glutamic acid concentration was obtained over a range of 11-220 mg O₂ L⁻¹ (6 points, n = 3, R.S.D._av 3.71%) with a detection limit of 5.5 mg O₂ L⁻¹ when using a reaction mixture and incubating for only 5 min. Subsequently, the characterization of this method was studied. First, the BOD_CL responses to 16 pure organic substances were examined. Second, the influences of chloride ions, artificial seawater, and heavy metal ions on the BOD_CL response were investigated. Real sample measurements using river water were performed. Finally, BOD_CL responses were obtained for at least 8 days when the S. cerevisiae suspension was stored at 4 °C (response reduction, 69.9%; R.S.D. for 5 testing days, 18.7%). BOD_CL responses after 8 days and 24 days were decreased to 69.9% and 35.8%, respectively, from their original values (R.S.D. for 8 days involving 5 testing days, 18.7%).     

Improvement of the analysis of the biochemical oxygen demand (BOD) of Mediterranean seawater by seeding control

Biochemical oxygen demand (BOD) is a useful parameter for assessing the biodegradability of dissolved organic matter in water. At the same time, this parameter is used to evaluate the efficiency with which certain processes remove biodegradable natural organic matter (NOM). However, the values of BOD in seawater are very low (around 2 mg O₂ L⁻¹) and the methods used for its analysis are poorly developed. The increasing attention given to seawater desalination in the Mediterranean environment, and related phenomena such as reverse osmosis membrane biofouling, have stimulated interest in seawater BOD close to the Spanish coast. In this study the BOD analysis protocol was refined by introduction of a new step in which a critical quantity of autochthonous microorganisms, measured as adenosine triphosphate, is added. For the samples analyzed, this improvement allowed us to obtain reliable and replicable BOD measurements, standardized with solutions of glucose-glutamic acid and acetate. After 7 days of analysis duration, more than 80% of ultimate BOD is achieved, which in the case of easily biodegradable compounds represents nearly a 60% of the theoretical oxygen demand. BOD₇ obtained from the Mediterranean Sea found to be 2.0 ± 0.3 mg O₂ L⁻¹ but this value decreased with seawater storage time due to the rapid consumption of labile compounds. No significant differences were found between two samples points located on the Spanish coast, since their organic matter content was similar. Finally, the determination of seawater BOD without the use of inoculum may lead to an underestimation of BOD.     

A highly sensitive amperometric sensor for oxygen based on iron(II) tetrasulfonated phthalocyanine and iron(III) tetra-(N-methyl-pyridyl)-porphyrin multilayers

The development of a highly sensitive sensor for oxygen is proposed using a glassy carbon (GC) electrode modified with alternated layers of iron(II) tetrasulfonated phthalocyanine (FeTsPc) and iron(III) tetra-(N-methyl-pyridyl)-porphyrin (FeT4MPyP). The modified electrode showed excellent catalytic activity for the oxygen reduction. The reduction potential of the oxygen was shifted about 330 mV toward less negative values with this modified electrode, presenting a peak current much higher than those observed on a bare GC electrode. Cyclic voltammetry and rotating disk electrode (RDE) experiments indicated that the oxygen reduction reaction involves 4 electrons with a heterogenous rate constant (k_obs) of 3 × 10⁵ mol⁻¹ L s⁻¹. A linear response range from 0.2 up to 6.4 mg L⁻¹, with a sensitivity of 4.12 μA L mg⁻¹ (or 20.65 μA cm⁻² L mg⁻¹) and a detection limit of 0.06 mg L⁻¹ were obtained with this sensor. The repeatability of the proposed sensor, evaluated in terms of relative standard deviation (R.S.D.) was 2.0% for 10 measurements of a solution of 6.4 mg L⁻¹ oxygen. The sensor was applied to determine oxygen in pond and tap water samples showing to be a promising tool for this purpose.     

A green analytical procedure for flow-injection determination of nitrate in natural waters

Nitrate determination in waters is generally carried out with cadmium filings and carcinogenic reagents or by reaction with phenolic compounds in highly concentrated sulfuric acid medium. In this work, it was developed a green analytical procedure for nitrate determination in natural waters based on direct spectrophotometric measurements in ultraviolet, using a flow-injection system with an anion-exchange column for separation of nitrate from interfering species. The proposed method employs only one reagent (HClO₄) in a minimum amount (equivalent to 18 μL concentrated acid per determination), and allowed nitrate determination within 0.50-25.0 mg L⁻¹, without interference of up to 200.0 mg L⁻¹ humic acid; 1.0 mg L⁻¹ NO₂⁻; 200.0 mg L⁻¹ PO₄³⁻; 75.0 mg L⁻¹ Cl⁻; 50.0 mg L⁻¹ SO₄²⁻ and 15.0 mg L⁻¹ Fe³⁺. The detection limit (99.7% confidence level) and the coefficient of variation (n = 20) were estimated as 0.1 mg L⁻¹ and 0.7%, respectively. The results obtained for natural water samples were in agreement with those achieved by the reference method based on nitrate reduction with copperized cadmium at the 95% confidence level.     

Optical biosensor for the determination of BOD in seawater

An automatic sensing system was developed using an optical BOD sensing film. The sensing film consists of an organically modified silicate (ORMOSIL) film embedded with an oxygen-sensitive Ru complex. A multi-microorganisms immobilization method was developed for the BOD sensing film preparation. Three different kinds of microorganisms, Bacillus licheniformis, Dietzia maris and Marinobacter marinus from seawater, were immobilized on a polyvinyl alcohol ORMOSILs. After preconditioning, the BOD biosensor could steadily perform well up to 10 months. The linear fluctuant coefficients (R²) in the range of 0.3-40 mg L⁻¹ was 0.985 when a glucose/glutamate BOD standard was applied. The reproducible response for the BOD sensing film could be obtained within ±2.3% of the mean value in a series of 10 samples in 5.0 mg L⁻¹ BOD standard GGA solution. The effects of temperature, pH and sodium chloride concentration on the two microbial films were studied as well. The BOD sensing system was tested and applied for the BOD determination of seawater.     

Detoxification of antimony by selenium and their interaction in paddy rice under hydroponic conditions

Antimony (Sb) contamination has become a growing concern in recent years. Strategies for reducing Sb contamination and its related health risks are urgently desired. This study was conducted to explore the possibility of selenium (Se) detoxification on Sb toxicity in paddy rice in order to find a feasible method to reduce the health risk of Sb pollution. Seedlings of paddy rice were exposed to 5 mg L⁻¹ Sb (KSbC₄H₄ O₇·1/2H₂O), in the presence of Se (Na₂SeO₃) at 0.1, 1, 5 mg L⁻¹ in culture solution, with no Sb and Se addition as the control. Paddy rice took up Sb greatly and the highest Sb contents measured among all treatments in this experiment in the leaves, stems and roots were 65.5, 298.5 and 195.7 mg kg⁻¹, respectively. Without Sb addition in the solution, single exposure to 0.1 mg L⁻¹ Se remarkably reduced the malondialdehyde (MDA) formation in paddy rice,demonstrating the beneficial effect of Se at low dosages. The addition of 5 mg L⁻¹ Sb was found to generate toxicity to paddy rice, showing as decreased biomass and increased leaf MDA content in paddy rice, while addition of 1 mg L⁻¹ Se mitigated the toxicity of Sb, as seen with the decreased leaf MDA content and increased biomass, indicating antidotal role of Se to Sb. In addition, the presence of 0.1, 1, 5 mg L⁻¹ Se generally decreased the accumulation of Sb in the leaves, stems and roots in paddy rice. Toxicity was also seen when paddy rice was exposed to single Se at 1 and 5 mg L⁻¹ levels, however, 5 mg L⁻¹ Sb addition was found to decrease the contents of Se in the leaves/stems whereas increased them in roots, accompanied with decreased MDA contents and increased biomass in paddy rice, indicating a possible detoxification role of Sb to Se too. Therefore, Sb, although toxic, could also be an antitoxin to Se in paddy rice at certain condition. Our results showed that Se could alleviate Sb toxicity efficiently in paddy rice through two effects as antagonism and antioxidation.     

New procedure of selected biogenic amines determination in wine samples by HPLC

A new procedure for determination of biogenic amines (BA): histamine, phenethylamine, tyramine and tryptamine, based on the derivatization reaction with 2-chloro-1,3-dinitro-5-(trifluoromethyl)-benzene (CNBF), is proposed. The amines derivatives with CNBF were isolated and characterized by X-ray crystallography and ¹H, ¹³C, ¹⁹F NMR spectroscopy in solution. The novelty of the procedure is based on the pure and well-characterized products of the amines derivatization reaction. The method was applied for the simultaneous analysis of the above mentioned biogenic amines in wine samples by the reversed phase-high performance liquid chromatography. The procedure revealed correlation coefficients (R²) between 0.9997 and 0.9999, and linear range: 0.10–9.00 mg L⁻¹ (histamine); 0.10–9.36 mg L^-1 (tyramine); 0.09–8.64 mg L⁻¹ (tryptamine) and 0.10–8.64 mg L⁻¹ (phenethylamine), whereas accuracy was 97%–102% (recovery test). Detection limit of biogenic amines in wine samples was 0.02–0.03 mg L⁻¹, whereas quantification limit ranged 0.05–0.10 mg L⁻¹. The variation coefficients for the analyzed amines ranged between 0.49% and 3.92%. Obtained BA derivatives enhanced separation the analytes on chromatograms due to the inhibition of hydrolysis reaction and the reduction of by-products formation.     

An amperometric biosensor based on peroxidases from Brassica napus for the determination of the total polyphenolic content in wine and tea samples

An amperometric biosensor based on peroxidases from Brassica napus hairy roots (PBHR) used to determine the total polyphenolic content in wine and tea samples is proposed by the first time. The method employs carbon paste (CP) electrodes filled up with PBHR, ferrocene (Fc), and multi-walled carbon nanotubes embedded in a mineral oil (MWCNT + MO) at a given composition (PBHR-Fc-MWCNT + MO). The biosensor was covered externally with a dialysis membrane, which was fixed at the electrode body side part with a Teflon laboratory film and an O-ring. Calibration curves obtained from steady-state currents as a function of the concentration of a polyphenolic standard reference compound such as t-resveratrol (t-Res) or caffeic acid (CA) were then used to estimate the total polyphenolic content in real samples. The reproducibility and the repeatability were of 7.0% and 4.1% for t-Res (8.4% and 5.2% for CA), respectively, showing a good biosensor performance. The calibration curves were linear in a concentration range from 0.05 to 52 mg L⁻¹ and 0.06 to 69 mg L⁻¹ for t-Res and CA, respectively. The lowest polyphenolic compound concentration values measured experimentally for a signal to noise ratio of 3:1 were 0.023 mg L⁻¹ and 0.020 mg L⁻¹ for t-Res and CA, respectively.     

Efficient generation of volatile species for cadmium analysis in seafood and rice samples by a modified chemical vapor generation system coupled with atomic fluorescence spectrometry

A vapor generation procedure to determine Cd by atomic fluorescence spectrometry (AFS) has been established. Volatile species of Cd are generated by following reaction of acidified sample containing Fe(II) and l-cysteine (Cys) with sodium tetrahydroborate (NaBH₄). The presence of 5 mg L⁻¹ Fe(II) and 0.05% m/v Cys improves the efficiency of Cd vapor generation substantially about four-fold compared with conventional thiourea and Co(II) system. Three experiments with different mixing sequences and reaction times are designed to study the reaction mechanism. The results document that the stability of Cd(II)–Cys complexes is better than Cys–THB complexes (THB means NaBH₄) while the Cys–THB complexes have more contribution to improve the Cd vapor generation efficiency than Cd(II)–Cys complexes. Meanwhile, the adding of Fe(II) can catalyze the Cd vapor generation. Under the optimized conditions, the detection limit of Cd is 0.012 μg L⁻¹; relative standard deviations vary between 0.8% and 5.5% for replicate measurements of the standard solution. In the presence of 0.01% DDTC, Cu(II), Pb(II) and Zn(II) have no significant influence up to 5 mg L⁻¹, 10 mg L⁻¹and 10 mg L⁻¹, respectively. The accuracy of the method is verified through analysis of the certificated reference materials and the proposed method has been applied in the determination of Cd in seafood and rice samples.     

Dissolved oxygen amperometric sensor based on layer-by-layer assembly using host-guest supramolecular interactions

The development of a simple, efficient and sensitive sensor for dissolved oxygen is proposed using the host-guest binding of a supramolecular complex at a host surface by combining a self-assembled monolayer (SAM) of mono-(6-deoxy-6-mercapto)-β-cyclodextrin (βCDSH), iron (III) tetra-(N-methyl-4-pyridyl)-porphyrin (FeTMPyP) and cyclodextrin-functionalized gold nanoparticles (CDAuNP). The supramolecular modified electrode showed excellent catalytic activity for oxygen reduction. The reduction potential of oxygen was shifted about 200 mV toward less negative values with this modified electrode, presenting a peak current much higher than those observed on a bare gold electrode. Cyclic voltammetry and rotating disk electrode (RDE) experiments indicated that the oxygen reduction reaction involves probably 4-electrons with a rate constant (k_obs) of 7 × 10⁴ mol⁻¹ L s⁻¹. A linear response range from 0.2 up to 6.5 mg L⁻¹, with a sensitivity of 5.5 μA L mg⁻¹ (or 77.5 μA cm⁻² L mg⁻¹) and a detection limit of 0.02 mg L⁻¹ was obtained with this sensor. The repeatability of the proposed sensor, evaluated in terms of relative standard deviation was 3.0% for 10 measurements of a solution of 6.5 mg L⁻¹ oxygen.     

Hybrid sequential injection-flow injection manifold for the spectrophotometric determination of total sulfite in wines using o-phthalaldehyde and gas-diffusion

A new automated spectrophotometric method for the determination of total sulfite in white and red wines is reported. The assay is based on the reaction of o-phthalaldehyde (OPA) and ammonium chloride with the analyte in basic medium under SI conditions. Upon on-line alkalization with NaOH, a blue product is formed having an absorption maximum at 630 nm. The parameters affecting the reaction - temperature, pH, ionic strength, amount concentration and volume of OPA, amount concentration of ammonium chloride, flow rate and reaction coil length - and the gas-diffusion process - sample and HCl volumes, length of mixing coil, donor flow rate - were studied. The proposed method was validated in terms of linearity (1-40 mg L⁻¹, r = 0.9997), limit of detection (c_L = 0.3 mg L⁻¹) and quantitation (c_Q = 1.0 mg L⁻¹), precision (s_r = 2.2% at 20 mg L⁻¹ sulfite, n = 12) and selectivity. The applicability of the analytical procedure was evaluated by analyzing white and red wine samples, while the accuracy as expressed by recovery experiments ranged between 96% and 106%.     

Reversed flow injection spectrophotometric determination of chlorate

An interfacing has been developed to connect a spectrophotometer with a personal computer and used as a readout system for development of a simple, rapid and sensitive reversed flow injection (rFI) procedure for chlorate determination. The method is based on the oxidation of indigo carmine by chlorate ions in an acidic solution (dil. HCl) leading to the decrease in absorbance at 610 nm. The decrease in absorbance is directly related to the chlorate concentration present in the sample solutions. Optimum conditions for chlorate were examined. A linear calibration graph over the range of 0.1-0.5 mg L⁻¹ chlorate was established with the regression equation of Y = 104.5X + 1.0, r² = 0.9961 (n = 6). The detection limit (3σ) of 0.03 mg L⁻¹, the limit of quantitation (10σ) of 0.10 mg L⁻¹ and the RSD of 3.2% for 0.3 mg L⁻¹ chlorate (n = 11) together with a sample throughput of 92 h⁻¹ were obtained. The recovery of the added chlorate in spiked water samples was 98.5 ± 3.1%. Major interferences for chlorate determination were found to be BrO₃⁻, ClO₂⁻, ClO⁻ and IO₃⁻ which were overcome by using SO₃²⁻ (as Na₂SO₃) as masking agent. The method has been successfully applied for the determination of chlorate in spiked water samples with the minimum reagent consumption of 14.0 mL h⁻¹. Good agreement between the proposed rFIA and the reference methods was found verified by Student's t-test at 95% confidence level.     

Absorption-based highly sensitive and reproducible biochemical oxygen demand measurement method for seawater using salt-tolerant yeast Saccharomyces cerevisiae ARIF KD-003

Salt-tolerant yeast Saccharomyces cerevisiae ARIF KD-003 was applied to highly sensitive and reproducible absorbance-based biochemical oxygen demand (BOD_AB-ScII) measurement for seawater. In the previous work, we have studied the BOD_AB-ScI method using normal Baker's yeast S. cerevisiae, and the excellent feature of the Baker's yeast as uniformly sustainable in solution could successfully be utilized. However, the BOD_AB-ScI responses were disappeared by the existence of chloride ion as well as seawater. In the present method, uniformity in solution was also observed with S. cerevisiae ARIF KD-003, and salt-tolerance of the yeast was observed even in saturate concentration of sodium chloride. Next, characterizations of the influences of pH and incubation temperature were investigated. After optimum conditions were obtained, two calibration curves were made between 0.33 and 22 mg O₂ L⁻¹ BOD using standard solution of glucose glutamic acid (GGA) or mixture of GGA and artificial seawater. Then, excellent reproducibility as the averages of relative standard deviation (R.S.D._av) in two calibration curves (nine points each) was successfully obtained at 1.10% at pure water or 1.03% at artificial seawater standard, respectively. In addition, the 3σ lower detection limit was calculated to be 0.07 mg O₂ L⁻¹ BOD, and 0.11 mg O₂ L⁻¹ BOD was experimentally detected by increase of the sample volume at 1.5-folds. The storage stability of the S. cerevisiae ARIF KD-003 was obtained at least 4 weeks.     

Sequential injection methodology for carbon speciation in bathing waters

A sequential injection method (SIA) for carbon speciation in inland bathing waters was developed comprising, in a single manifold, the determination of dissolved inorganic carbon (DIC), free dissolved carbon dioxide (CO₂), total carbon (TC), dissolved organic carbon and alkalinity. The determination of DIC, CO₂ and TC was based on colour change of bromothymol blue (660 nm) after CO₂ diffusion through a hydrophobic membrane placed in a gas diffusion unit (GDU). For the DIC determination, an in-line acidification prior to the GDU was performed and, for the TC determination, an in-line UV photo-oxidation of the sample prior to GDU ensured the conversion of all carbon forms into CO₂. Dissolved organic carbon (DOC) was determined by subtracting the obtained DIC value from the TC obtained value. The determination of alkalinity was based on the spectrophotometric measurement of bromocresol green colour change (611 nm) after reaction with acetic acid. The developed SIA method enabled the determination of DIC (0.24–3.5 mg C L⁻¹), CO₂ (1.0–10 mg C L⁻¹), TC (0.50–4.0 mg C L⁻¹) and alkalinity (1.2–4.7 mg C L⁻¹ and 4.7–19 mg C L⁻¹) with limits of detection of: 9.5 μg C L⁻¹, 20 μg C L⁻¹, 0.21 mg C L⁻¹, 0.32 mg C L⁻¹, respectively. The SIA system was effectively applied to inland bathing waters and the results showed good agreement with reference procedures.     

Sensitive determination of hydrazine in water by gas chromatography–mass spectrometry after derivatization with ortho-phthalaldehyde

A gas chromatography–mass spectrometric (GC–MS) method has been established for the determination of hydrazine in drinking water and surface water. This method is based on the derivatization of hydrazine with ortho-phthalaldehyde (OPA) in water. The following optimum reaction conditions were established: reagent dosage, 40 mg mL⁻¹ of OPA; pH 2; reaction for 20 min at 70 °C. The organic derivative was extracted with methylene chloride and then measured by GC–MS. Under the established condition, the detection and the quantification limits were 0.002 μg L⁻¹ and 0.007 μg L⁻¹ by using 5.0-mL of surface water or drinking water, respectively. The calibration curve showed good linearity with r² = 0.9991 (for working range of 0.05–100 μg L⁻¹) and the accuracy was in a range of 95–106%, and the precision of the assay was less than 13% in water. Hydrazine was detected in a concentration range of 0.05–0.14 μg L⁻¹ in 2 samples of 10 raw drinking water samples and in a concentration range of 0.09–0.55 μg L⁻¹ in 4 samples of 10 treated drinking water samples.     

Multi-pumping flow system for the determination of dissolved orthophosphate and dissolved organic phosphorus in wastewater samples

A multi-pumping flow system (MPFS) for the spectrophotometric determination of dissolved orthophosphate and dissolved organic phosphorus in wastewater samples is proposed. The determination of orthophosphate is based on the vanadomolybdate method. In-line ultraviolet photo-oxidation is employed to mineralise organic phosphorus to orthophosphate prior to detection. A solenoid valve allows the deviation of the flow towards the UV-lamp to carry out the determination of organic phosphorus.Calibration was found to be linear up to 20 mg P L⁻¹, with a detection limit (3s_b/S) of 0.08 mg P L⁻¹, an injection throughput of 75 injections h⁻¹ and a repeatability (R.S.D.) of 0.6% for the direct determination of orthophosphate. On the other hand, calibration graphs were linear up to 40 mg P L⁻¹, with a detection limit (3s_b/S) of 0.5 mg P L⁻¹, an injection throughput of 11 injections h⁻¹ and a repeatability (R.S.D.) inferior to 2.3% for the procedures involving UV photo-oxidation.     

Development of a high-performance liquid chromatography-fluorescence detection method for analyzing nonylphenol/dinonylphenol-polyethoxylate-based phosphate esters

A novel reversed phase HPLC method for the simultaneous analysis of surfactants containing nonylphenol/dinonylphenol-polyethoxylates and their o-phosphate esters is reported, in which eluting substances are detected fluorescently. Their chemical structures were elucidated by direct infusion electrospray-mass spectrometry in positive mode. The limits of quantification and range of the method were determined to be 0.1 mg and 0.1–100 mg surfactant L⁻¹, respectively, with a reproducibility (RSD) at a concentration of 38 mg surfactant L⁻¹ of 5.6%. The accuracy was determined by spiking selected process water samples with known amounts of surfactant, and recoveries were typically in the 82–102% range.     

Direct chiral resolution and its application to the determination of fungicide benalaxyl in soil and water by high-performance liquid chromatography

A simple chiral high-performance liquid chromatography (HPLC) method with ultraviolet (UV) and circular dichroism (CD) detection was developed and validated for measuring benalaxyl enantiomers using (R,R) Whelk-O 1 column. The effects of mobile phase composition and column temperature on the entioseparation were investigated. A CD detector was used to determine the elution order of the enantiomers. Excellent resolution was easily obtained using n-hexane-polar organic alcohols mobile phase. The chiral recognition mechanism was also discussed. Based on the developed chiral HPLC method, enantioselective analysis methods for this fungicide in environment matrix (soil and water) were developed and validated. Good linearities were obtained over the concentration range of 0.25-25 mg L⁻¹ for both enantiomers. Liquid-liquid extraction and solid phase extraction (SPE) were used for the enrichment and cleanup of soil and water samples. Recoveries for the two enantiomers were 79-91% at 0.02, 0.04 and 0.2 mg kg⁻¹ levels from soil, and 89-101% at 0.0025, 0.01 and 0.05 mg L⁻¹ levels from water. Run-to-run and day-to-day assay precisions were below 10% for both enantiomers at concentrations of 0.5, 1 and 5 mg L⁻¹. Individual detection limits of the two enantiomers were both 2 ng. Limits of detection (LOD) were 0.004 mg kg⁻¹ in soil and 0.001 mg L⁻¹ in water.