Preparation and characterization of anion‐exchange membranes derived from poly(vinylbenzyl chloride‐co‐styrene) and intercalated montmorillonite

In this paper, three organic intercalating agents containing cations [hexadecyl trimethyl ammonium bromide (CTAB), poly(acrylamide‐co‐diallyldimethylammonium chloride), and quaternized polyethyleneimine] are used to prepare intercalated montmorillonites (MMT) by ion‐exchange method. Then the modified MMTs are doped with vinylbenzyl chloride and styrene copolymer [poly(vinylbenzyl chloride‐co‐styrene)] for fabricating composite anion‐exchange membranes (AEM). Fourier transform infrared, X‐raydiffraction, thermogravimetric analysis, scanning electron microscopy, and Mastersizer laser particle size analyzer are employed to characterize the structure and morphology of MMTs and AEMs. The successful intercalation of MMTs is approved, and the MMT intercalated by CTAB shows an interlayer distance of 2.31 nm. The properties of the composite membranes including water uptake, mechanical property, and ionic conductivity are investigated. Among all the AEMs, the composite membrane containing MMT sheets with CTAB demonstrates better compositive performances. It presents an ionic conductivity of 2.09 × 10^?2 S cm^?1 at 80°C and good alkaline solution stability. Copyright © 2016 John Wiley & Sons, Ltd.     

TG characterization of organically modified montmorillonite

Montmorillonite was modified with octadecyltrimethylammonium chloride, under different reaction conditions, as evidenced by TG and XRD. TG curves presented two degradation peaks (295 and 395°C). At low salt concentrations, only the 395°C-degradation appeared, which increased with reaction time to the limit of 9 g of salt/100 g of clay. The second peak presented a limit at 17/100 m/m of salt/clay ratio. XRD analysis confirmed clay organic modification as the basal distance increased, showing greater reaction time effect than the salt mass effect, and with only one d-spacing. This suggested that an intercalation complex was formed but also that octadecyltrimethylammonium was adsorbed on the external surfaces of clay particles. This revised version was published online in August 2006 with corrections to the Cover Date.     

Thermal behaviour of intercalated 8-hydroxyquinoline (oxine) in montmorillonite clay

The composite montmorillonite-8-hydroxyquinoline (Swy-1-8-HQ) was prepared by two different processes and studied by using thermogravimetric analysis (TG/DTG and DSC), as well as helpful techniques as fluorescence in the UV-visible region and X-ray diffraction. The composites developed fluorescent appearance, however with quantum poor efficiency and they exhibited distinct TG and DSC thermal behavior. The fluorescence data of spectra associated to the TG/DT curves allowed to suggest that the 8-HQ was present in the composites in two different circumstances: 1 - intercalated in the interlayer spaces (Swy-1-8-HQ2), rigidly associated to the substrate feasible as a monolayer with the aromatic rings parallel to the silica layer; and/or, 2 - adsorbed on the surface (Swy-1-8-HQ1), either as a bilayer formation or tilting of the molecules to the silicate layer sheet. All results confirmed above are in agreement with X-ray diffraction patterns, once the interlayer space increases when 8-HQ is incorporated. The experimental results confirm the formation of the composites in agreement with the method used in the preparation. This revised version was published online in August 2006 with corrections to the Cover Date.     

Insertion of benzothiazolium compounds into montmorillonite interlayers

Benzothiazolium compounds exhibit pronounced antimicrobial activities and stimulation effects on plant growth. When applied to fields they can pollute soil colloids. In contact with the soil they can potentially interact with a clay fraction giving rise to clay organocomplexes. Model intercalation complexes were prepared using monoionic montmorillonite and a variety of water-soluble benzothia zolium salts. It was found that the adsorption into the silicate interlayer space proceeds via a cation exchange process. Substantial differences were observed in the extent of the reaction between non-substituted andN-substituted species. The sulphur atoms present in the benzothiazolium molecules repel the surface oxygen atom: this is considered to be the factor responsible for prevention of insertion of the guest cations perpendicular to the layers.     

Synthesis of a novel benzoxazine monomer‐intercalated montmorillonite and the curing kinetics of polybenzoxazine/clay hybrid nanocomposites

Polybenzoxazine (PBZ), which has a structure similar to that of phenolic resin, is formed through the thermal self‐curing of benzoxazine, that is through a heterocyclic ring opening reaction that requires no catalyst and releases no condensation byproducts. We have used the solvent blending method to prepare PBZ/clay nanocomposites possessing various clay contents. We synthesized a monofunctional benzoxazine monomer (MBM) and then treated the clay with this intercalation agent. The results of X‐ray diffraction (XRD) analysis indicated that MBM intercalated into the galleries of the clay; the nanocomposite possessed an exfoliated structure at 3% clay content. To better understand the curing kinetics of the PBZ/clay nanocomposites, we performed dynamic and isothermal differential scanning calorimetry (DSC) measurements. We describe the thermodynamics of the curing process, using all three of the Kissinger, Ozawa, and Kamal models. The Kissinger and Ozawa methods gave fairly close results for the calculated activation energies, which decreased upon increasing the clay content. The Kamal method, based on an autocatalytic model, suggested a total reaction order of between 2.4 and 2.8. The glass transition temperature (T_g) decreased upon increasing the clay content. Thermogravimetric analysis (TGA) indicated that the nanocomposites have higher decomposition temperatures than does the pristine PBZ; this finding suggests an enhancement in their thermal stability. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 347–358, 2006     

Organic‐montmorillonite modified shape memory epoxy composite

A series of organic‐montmorillonite (OMMT) modified shape memory epoxy (SMEP) composites were prepared for the purpose of application on space deployable structures. Tensile test, dynamic mechanical analysis (DMA), X‐ray diffraction (XRD), scanning electron microscope (SEM), and fold‐deploy shape memory test methods were used to characterize the mechanical, structure, and shape memory properties of these materials. The results showed addition of OMMT could improve the composites' toughness, tensile strength, transition temperature, and shape recovery speed, while shape recovery ratio was unaffected. Composite with 3wt%. OMMT had the optimum combination property. It could fully recover its original shape in about 2 min at 185°C under the maximum bending angle of 180°. Its elongation at break and tensile strength were increased by 835 and 17.4%, respectively, compared to that of neat SMEP. The transition temperature also slightly increased. Copyright © 2010 John Wiley & Sons, Ltd.     

Novel composite polymer electrolytes based on poly(ether-urethane) network polymer and modified montmorillonite

Novel composite solid polymer electrolytes (CSPEs) and composite gel polymer electrolytes (CGPEs) have been prepared. CSPE consists of poly(ether-urethane) network polymer, which is superior to poly(ethylene oxide) in mechanical stability due to its cross-linked structure, modified montmorillonite (MMMT) and LiClO₄, and CGPE with good mechanical strength comprises of the CSPE and LiClO₄–PC (propylene carbonate) solution. The ionic conductivity can be enhanced after the addition of MMMT, and CGPE exhibits ionic conductivity in the order of 10⁻³ S/cm at room temperature. The temperature dependence of the ionic conductivity of the CSPE follows the Vogel–Tamman–Fulcher (VTF) equation. The effects of MMMT on the interactions in these systems and the possible conduction mechanisms are also discussed.     

Synthesis and characterization of polycyanurate/montmorillonite nanocomposites

The advantages of cyanate esters (CEs) versus competitor systems such as epoxies and polyimides, as well as the great reinforcing potential of organoclays properly dispersed into a polymeric matrix, have been examined in a series of polycyanurate (PCN)/montmorillonite (MMT) nanocomposites prepared under appropriate polymerization conditions. The curing schedule applied resulted in gradual propagation of polymerization. Through this procedure, the intragallery curing rate becomes comparable to the extragallery one, allowing intercalation before gelation. Systems with clay loadings from 1 to 3% per weight were synthesized, and their morphology and mechanical properties were studied by means of scanning electron microscopy (SEM), atomic force microscopy (AFM), wide angle X‐ray scattering (WAXS), dynamic mechanical analysis (DMA), and tensile tests. Microscopy investigations revealed better dispersion for the 3 wt % system compared to smaller concentrations, in which aggregation and, in some cases, agglomeration were the conspicuous features. Roughness and area analyses revealed more homogeneous dispersion for this nanocomposite. Topology and 3D‐phase images further suggested considerable reduction of the average particle diameters. WAXS analysis showed that the interlayer spacing of nanocomposites was increased compared to pristine MMT, indicating the formation of intercalated structures. On the other hand, tensile strength and elongation at break values displayed abrupt diminution with MMT addition, while Young's modulus exhibited a slight but systematic increment with MMT content. The decreasing glass transition tendency observed for small clay loadings was reversed in the case of 3 wt %, while secondary transitions were practically unaffected by the presence of MMT. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1036–1049, 2008     

Spectroscopic studies on organic molecules intercalated into clays

An overview of clay structures and characterization methods is followed by a discussion of some adsorption reactions of organic molecules which have been studied spectroscopically. These can be divided into two main classes: adsorption with and without reaction.Presented at the Sixth International Seminar on Inclusion Compounds, Istanbul, Turkey, 27–31 August 1995.     

Ionomer-silicates composite membranes: Permeability and conductivity studies

Polymer composite membranes based on sulphonated polymers, such as sulphonated poly(ether ketone) and sulphonated poly(ether ether ketone), and silicates were prepared and characterized for water/methanol permeabilities and proton conductivity studies. The study showed methanol and water permeability in the composite system decreased, with respect to the plain polymer/ionomer, with the increase in content of silicates. The permeability reduction in the composite membranes is discussed using models and theories. It was also found that the proton conductivity of the ionomer-composite membranes increased with the increase in total flux of the system, emphasising a good correlation between the total flux of the composite membranes and proton conductivity. The work clearly demonstrates that the same transport mechanism governs both methanol-water crossover and proton conductivity in these polymer electrolyte composite membranes.     

Synthesis of an intercalated compound of montmorillonite and 6-polyamide

Natural montmorillonite, fractionated from bentonite produced in Yamagata, Japan, was ion-exchanged for NH ₃ ⁺ –(CH₂)₁₁–COOH, NH ₃ ⁺ –(CH₂)₅–COOH, Al³⁺, Cu²⁺, Mg²⁺, Co²⁺, Li⁺, K⁺ and H⁺. The mixtures of the ion-exchanged montmorillonite and -caprolactam were heated at 263°C in glass ampoules for various periods. The intercalated compounds before and after the heating were examined by X-ray powder diffraction, DSC and GPC. Although -caprolactam was not polymerized without montmorillonite, it was polymerized at 263°C in the presence of montmorillonite. The polymerization rate varied with the interlayer cations in the order of NH ₃ ⁺ –(CH₂)₁₁–COOH>Al³⁺>NH ₃ ⁺ –(CH₂)₅–COOH>H⁺>Cu²⁺>Mg²⁺>Co²⁺>Li⁺>K⁺. After heating at 263°C for 5 h, the mean number-average molecular weight was about 1.5×10⁴. Although the interlayer distance of NH ₃ ⁺ –(CH₂)₁₁–COOH type montmorillonite/-caprolactam compound increased from 2.85 nm to 4.90 nm by heating at temperatures above the melting point of -caprolactam, those of other compounds were not changed. After heating at 263°C, an intercalated compound of montmorillonite and 6-polyamide, whose interlayer distance was more than 10 nm, was obtained. It is concluded that montmorillonite acts as a Brönsted acid and initiates the open ring polymerization of -caprolactam and that the driving force of swelling is the polymerization energy.Presented at the Fourth International Symposium on Inclusion Phenomena and the Third International Symposium on Cyclodextrins, Lancaster, U.K., 20–25 July 1986.     

Differential thermal analysis of montmorillonite

The paper provides an overview of publications on the DTA of montmorillonites (in the temperature range 20–1100°C), starting with the first experiments of Le Chatelier (1887) and ranging up to the present. Consideration is given to the dehydration, dehydroxylation, amorphization and rehydration of montmorillonite (42 references).     

Synthesis of nylon 6–clay hybrid by montmorillonite intercalated with ϵ-caprolactam

It was found that montmorillonite was intercalated with ?-caprolactam. X-ray diffraction revealed that the chain axes of the ?-caprolactam were parallel to the montmorillonite plates. The intercalated montmorillonite was swollen by molten ?-caprolactam at 200°C. ?-Caprolactam and 6-aminocaproic acid (accelerator) were polymerized with the intercalated montmorillonite at 260°C for 6 h, yielding a nylon 6-clay hybrid. X-ray diffraction and transmission electron micrography revealed that the silicate layers of the hybrid were uniformly dispersed in the nylon 6 matrix. Mechanical properties of the hybrid were improved. The strength and the modulus of the hybrid increased compared with the previously reported nylon 6 clay-hybrid (NCH) synthesized by montmorillonite intercalated with 12-aminolauric acid. The heat distortion temperature (HDT) of the hybrid was 164°C, which was 12°C higher than that of NCH. © 1993 John Wiley & Sons, Inc.     

Modification and characterization of montmorillonite fillers used in composites with vulcanized natural rubber

Parent Ca-montmorillonite (Jelšovy Potok, Slovakia, Ca-JP) and Na-montmorillonite Kunipia-F (Japan, Na-KU) were ion-exchanged with octadecyltrimethylammonium (ODTMA) cations. Characteristics of the samples were studied by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (IR) and thermogravimetry (TG). Surface areas were measured by sorption of N₂ and ethyleneglycol monoethyl ether. Scanning electron microscopy photographs (SEM) were used to characterize the texture of samples. The XRD patterns show that, upon intercalation, the basal spacing of montmorillonite is expanded and corresponds to the pseudotrimolecular arrangement of organic cations in the interlayers. The IR spectra of organically modified montmorillonite show C-H stretching and bending bands of both CH₃ and CH₂ groups in the 3000–2800 cm⁻¹ and 1500–1400 cm⁻¹ region, respectively. Modification of montmorillonite by organic cations decreased the hydrophilicity of their mineral surface and adsorbed water evaporated at lower temperatures. The SEM photographs reveal a tendency towards lump formation and agglomeration of the ODTMA-montmorillonite particles. The modification introducing organic moiety lead to a substantial decrease in the surface area of both montmorillonites; however, it remained remarkably high, being at the level typical for silica. Completely characterized fillers were used to prepare rubber compositions with enhanced physical properties, as described in Hrachová et al. (2008).     

Electrochemical determination of lead(II) using a montmorillonite calcium-modified carbon paste electrode

Utilizing the fascinating properties of montmorillonite calcium (MMT-Ca), such as huge cationic exchange capacity, strong adsorptive ability, high chemical and mechanical stability, an MMT-Ca modified carbon paste electrode (CPE) was constructed for the sensitive determination of Pb²⁺. In 0.01 mol·L⁻¹ HCl, Pb²⁺ was firstly exchanged and accumulated on an MMT-Ca modified CPE surface and secondly reduced to Pb at −0.90 V. In the following potential sweep from −0.90 to −0.50 V, reduced Pb was oxidized, resulting in an obvious stripping peak at −0.58 V. After optimizing the parameters, such as determining medium, content of MMT-Ca, accumulation potential and time, an electrochemical method was developed for the analysis of Pb²⁺. Compared with bare CPE, the MMT-Ca modified CPE significantly enhances the sensitivity of Pb²⁺ analysis. The limit of detection is evaluated to be 6.0 × 10⁻⁹ mol L⁻¹ Pb²⁺. Finally, this method was successfully employed to determine trace levels of Pb²⁺ in water samples. The first two authors contribute equally do this work     

Electrochemical characterization of ionically conductive polymer membranes

Cation conductive membranes, especially highly proton conductive membranes, are of interest not only for chlor-alkali electrolysis but for polymer electrolyte fuel cells as well. The very challenge for electrochemical characterization in this case is the low specific resistance of the polymer required for such applications, which in turn makes resistance measurements a non-trivial problem. We investigate the different possibilities to characterize such membranes. The present part of our work deals with the adequate conditioning and equilibration of membranes designed especially for direct methanol fuel cell applications, with the measurement of the conductivity and with the determination of apparent transport numbers in the membrane. The usefulness of the respective leaching investigations, impedance spectroscopy measurements and concentration potential measurements for the case of membranes made from sulfonated poly(phenylene oxide) is discussed.     

Appealing sheath-core spun high-performance composite carbon molecular sieve membranes

Carbon molecular sieve (CMS) membranes are attractive candidates to meet requirements for challenging gas separations. The added ability to maintain such intrinsic properties in an asymmetric morphology with a structure that we term a “Pseudo Wheel+Hub & Spoke” asymmetric form offers new opportunities. For CMS membrane, specifically, the structure provides both selective layer support and low flow resistance even for high feed pressures and fluxes in CO₂ removal from natural gas. This capability is unavailable to even rigid glassy polymers due to the much higher modulus of CMS materials. Combining precursor asymmetric hollow fiber formation and optimized pyrolysis creates a defect free CMS proof-of-concept membrane for this application. Facile formation of the sheath-core spun precursor with a 6FDA-DAM sheath and Matrimid® core also avoids the need to seal defects before or after the carbonization of the precursors. The composite CMS membrane shows CO₂/CH₄ (50 : 50) mixed gas feed with an attractive CO₂/CH₄ selectivity of 64.3 and CO₂ permeance of 232 GPU at 35 °C. A key additional benefit of the approach is reduction in use of the more costly high performance 6FDA-DAM in a composite sheath-core CMS membrane with the “Pseudo Wheel+Hub & Spoke” structure.     

Application of thermal analysis methods for characterization of polymer/montmorillonite nanocomposites

Thermal analysis is a useful tool for investigating the properties of polymer/clay nanocomposites and mechanisms of improvement of thermal properties. This review work presents examples of applications of differential scanning calorimetry (DSC), modulated temperature differential scanning calorimetry (MT-DSC), dynamic mechanical thermal analysis (DMA), thermal mechanical analysis (TMA), thermogravimeric analysis (TG) and thermoanalytical methods i.e. TG coupled with Fourier transformation infrared spectroscopy (TG-FTIR) and mass spectroscopy (TG-MS) in characterization of nanocomposite materials. Complex behavior of different polymeric matrices upon modification with montmorillonite is briefly discussed.     

Synthesis, characterization and thermal studies on cellulose acetate membranes with additive

Cellulose acetate (CA) membranes are used in ultrafiltration applications, although they show low chemical, mechanical and thermal resistance. In order to prepare membranes with improved properties, modification of cellulose acetate with polyethelene glycol (PEG 600) has been attempted. In this study, CA has been mixed with PEG 600 as an additive in a polar solvent. The effects of CA composition and additive concentration given by a mixture design of experiments on membrane compaction, pure water flux, water content and membrane hydraulic resistance have been studied and discussed. The efficiency of protein separation by the developed CA membranes have been quantified using model proteins such as pepsin, egg albumin (EA) and bovine serum albumin (BSA). The thermal stability of the developed membranes prepared with PEG 600 additive has also been investigated using thermogravimetric analysis and differential scanning calorimetry.     

硫醇－磷脂混合双层膜的电化学性质及其与蜂毒素的相互 作用研究

报道了硫醇－磷脂混合双层膜的循环伏安和电化学交流阻抗行为研究,并用电化学方法考察了蜂毒素与其相互作用,实验中通过冷冻表面沾有磷脂溶液的硫醇单层膜制备混合双层膜,研究表明双层膜在电极表面形成致密的绝缘层,阻碍了电极表面的电子传递,在双层膜体系上引入的蜂毒素可在膜表面上形成孔洞,破坏膜的绝缘性,降低膜电阻,增加膜电容,使带负电的探针Fe(CN)6^3-的氧化还原反应速度加快。