金属钯纳米颗粒/氮化钛复合材料对水中2,4-二氯苯酚的电催化氢化脱氯（英文）

随着社会经济的快速发展,含氯有机物,特别是含氯苯系物,在农业、化工和医药等领域的使用量逐年增多,而使用过程中不合理的排放和控制致使含氯苯系物对生态环境,特别是水体环境的污染日趋严重.含氯苯系物具有高致毒致癌性,易生物富集,且很难被完全降解矿化,已被国家环保局认定为优先控制污染物.常规的废水处理工艺,如吸附、氧化及生物降解等,效率不高,且具有二次污染风险.电催化氢化脱氯技术是一种新型特别针对废水中含氯有机污染物的处理工艺,是通过在阴极电解还原水,原位生成原子态氢,以进攻苯环上C.Cl键,通过C.Cl键断裂H原子取代,使含氯苯系物完全转化为苯系物,达到去毒去害化的目的,近年来越来越受到研究者的关注.在整个电催化氢化脱氯技术中,高效稳定的电催化剂合成是关键,决定着脱氯效率、脱氯动力学、产物选择性及能量的利用率.本文报道了一种简易、无需添加任何表面活性剂的湿式还原法制备金属钯/氮化钛(Pd/TiN)和金属钯/碳(Pd/C)复合材料.在该复合材料中,金属钯颗粒具有均一的纳米尺寸(约5.0 nm)和球状形貌,且均匀分布在TiN和C载体上.作为针对水体中代表性含氯苯系物2,4-二氯苯酚的电催化氢化脱氯反应催化剂,Pd/TiN所展现的活性和稳定性均优于TiN和Pd/C,这源于TiN载体的促进作用.当TiN与Pd复合时,相应形成的Pd-TiN界面可改变Pd表面的电子结构,进一步优化Pd产活性氢及其吸附活化2,4-二氯苯酚的性能,因而其催化氢化脱氯活性增加.阴极工作电压是该催化反应中一个重要操作参数,决定了电催化氢化脱氯的效率和最终产物的构成.实验表明,.0.80 V vs Ag/AgCl是最佳操作电压,此时2,4-二氯苯酚的电催化氢化脱氯效率最高,可达到93.27%,且可实现最大程度的2,4-二氯苯酚向苯酚转化.脱氯反应路径研究发现,在Pd/TiN催化剂上2,4-二氯苯酚脱氯反应路径为2,4-二氯苯酚→对位一氯苯酚,邻位一氯苯酚→苯酚,但Pd/TiN对邻位和对位的C.Cl键断裂基本没有选择性.本文提供了一种新的有效调控Pd材料电催化氢化脱氯性能的方法,可望用于其他氢化反应体系的高效催化剂的设计合成,同时可推动电催化氢化脱氯技术在环境污染修复中的应用.     

CeO2纳米管负载Pd纳米颗粒催化CO低温氧化

高效负载型Pd催化剂的制备及其在CO低温氧化反应中的机理探究是近年来的研究热点.普遍认为,Pd催化剂上的CO氧化反应遵循Langmuir-Hinshelwood机理:首先,CO吸附于Pd物种表面;然后,CO与催化剂表面的晶格氧发生反应转化为CO2,反应发生在金属-载体界面.另外,高分散的Pd活性物种有利于CO氧化反应.同时载体的形貌、暴露的晶面、氧空位以及孔结构等都是影响催化剂活性的重要因素.CeO2纳米管具有独特的管状特征和较高的比表面积,是一种潜在的CO低温氧化催化剂载体.本文利用乙醇还原法,以CeO2纳米管为载体,制备不同Pd含量的Pd/CeO2-nanotube纳米催化剂,并利用N2吸附脱附、X射线衍射(XRD)、透射电子显微镜(TEM)、CO程序升温脱附(CO-TPD)、X射线光电子能谱(XPS)等表征手段,探索纳米催化剂载体形貌对CO氧化反应活性的影响.氮气吸脱附结果表明,Pd/CeO2-nanotube具有较高的比表面积(58.0 m2/g),且存在介孔结构.XRD表征发现,Pd/CeO2-nanotube的衍射峰对应立方萤石型结构的CeO2的(111),(200),(220),(311)等品面.TEM结果表明,Pd/CeO2-nanotube具有均匀的纳米管形貌,其外径为40-60 nm,Pd纳米颗粒均匀分散在其表面.CO-TPD结果表明,Pd/CeO2-nanotube在1 10℃附近具有很强的脱附峰,在370℃和600℃附近分别具有较宽和较弱的脱附峰,这表明该催化剂具有较多的吸附位,且具有很强的CO吸附能力;CO不可逆吸附量计算结果表明,该催化剂上的Pd具有很高的表面分散度(23.3％),Pd颗粒尺寸为7.3 nm.XPS表征显示,Pd以pd2+的形式分散于CeO2纳米管的表面,且与载体发生相互作用,存在Pd-O-Ce键;同时该催化剂表面存在丰富的Ce3+,为反应提供更多的氧空位.0.9Pd/CeO2-nanotube纳米催化剂在CO氧化反应中表现出优良的活性,能在100℃实现CO的完全转化;通过计算发现,该催化剂具有较高的TOF值(0.63 s-1),由Arrhenius 曲线可得到该催化剂的活化能为26.5 kJ/mol.综上可见:金属活性组分的尺寸和分散度、载体的结构特征、CO吸附能力以及金属-载体间的相互作用决定催化剂的性能.Pd/CeO2-nanotube的高比表面积有利于Pd的分散;其强CO吸附能力有利于CO吸附于Pd物种表面;催化剂表面丰富的Ce3+能为反应提供更多的氧空位,Pd-O-Ce键的形成能增强金属-载体间的相互作用,有利于CO与催化剂表面品格氧发生反应.同时催化剂介孔结构有利于反应气体和产物气体的吸附和扩散,因此,Pd/CeO2-nanotube纳米催化剂在CO氧化反应中表现出优良的活性.     

Electrochemistry and electrocatalytic activity of polypyrrole/ferrocyanide films on a glassy carbon electrode

Functionalized polypyrrole films were prepared by incorporation of Fe(CN)₆ ³⁻ as doping anion during the electropolymerization of pyrrole at a glassy carbon electrode from aqueous solution. The electrochemical behavior of the Fe(CN)₆ ³⁻/Fe(CN)₆ ⁴⁻ redox couple in polypyrrole was studied by cyclic voltammetry. An obvious surface redox reaction was observed and dependence of this reaction on the solution pH was illustrated. The electrocatalytic ability of polypyrrole film with ferrocyanide incorporated was demonstrated by oxidation of ascorbic acid at the optimized pH of 4 in a glycine buffer. The catalytic effect for mediated oxidation of ascorbic acid was 300 mV and the bimolecular rate constant determined for surface coverage of 4.5 × 10⁻⁸ M cm⁻² using rotating disk electrode voltammetry was 86 M⁻¹ s⁻¹. Furthermore, the catalytic oxidation current was linearly dependent on ascorbic acid concentration in the range 5 × 10⁻⁴–1.6 × 10⁻² M with a correlation coefficient of 0.996. The plot of i _p versus v ^1/2 confirms the diffusion nature of the peak current i _p. Received: 12 April 1999 / Accepted: 25 May 1999     

Pd nanoparticles supported on amphiphilic porous organic polymer as an efficient catalyst for aqueous hydrodechlorination and Suzuki-Miyaura coupling reactions

Developing efficient and recyclable heterogeneous catalysts for organic reactions in water is important for the sustainable development of chemical industry. In this work, Pd nanoparticles supported on DABCO-functionalized porous organic polymer was successfully prepared through an easy copolymerization and successive immobilization method. Characterization results indicated that the prepared catalyst featured big surface area, hierarchical porous structure, and excellent surface amphiphilicity. We demonstrated the use of this amphiphilic catalyst in two case reactions, i.e. the aqueous hydrodechlorination and Suzuki-Miyaura coupling reactions. Under mild reaction conditions, the catalyst showed high catalytic activities for the two reactions. In addition, the catalyst could be easily recovered and reused for several times. Also, no obvious Pd leaching and aggregation of Pd nanoparticles occurred up during the consecutive reactions.     

Stability and activity of Pd nanoparticles on silica and ultradispersed diamond

The influence of the nature of M_nO_m and treatment temperature of zirconia-based systems M_nO_m−ZrO₂ (M=Ca, Ba, Sm, Yb) of approximately equimolar composition on their phase composition and dispersity has been studied. The samples are shown to contain solid solutions based on cubic ZrO₂. Besides, CaZrO₃ perovskite is present in the CaO−ZrO₂ system, and a solid solution based on Sm₂O₃ is present in the Sm₂O₃−ZrO₂ system. The particle sizes in the corresponding solid solutions vary from 25 to 150 ?, while in the perovskite phase they are in the 300–500 ? range, with the treatment temperature increasing from 623 to 1273 K.     

弱磁性Co0.85Se纳米片负载碳纳米管作为电催化析氢催化剂

氢气是一种环境友好可再生的清洁能源,电解水无疑是一种很好的制氢方法.然而,电催化分解水析氢受到其缓慢的动力学过程、较低的催化性能和较差的稳定性的限制.为了使整个过程更节能,具有高电流密度和低的过电势的高效电催化剂被广泛研究.非化学计量相硒化钴(Co0.85Se)作为一种重要的金属硫属化合物具有优异的催化性能而广受关注.但是低维的Co0.85Se活性位点少,分散性差,电子传递能力低,导致其电催化剂活性差.多壁碳纳米管(MWCNTs)具有多种电性能,包括金属导电性和电子存储能力等.因此,MWCNTs的特殊结构和高导电性可以有效地促进电子从电催化剂向碳纳米管的转移,实现高效电分解水制氢性能.本文在不使用表面活性剂和模板的情况下,通过一步水热溶剂热法合成弱磁性Co0.85Se纳米片负载碳纳米管电催化剂.采用磁滞回线研究Co0.85Se和MWCNTs/Co0.85Se的磁性能,结果表明其有弱顺磁性,Co0.85Se纳米片之间的空间距离增强导致粒子间偶极相互作用减弱,从而使MWCNTs/Co0.85Se纳米复合材料的矫顽力值增加到158 Oe.随着微晶尺寸的减小和纳米颗粒间距的增大,MWCNTs/Co0.85Se催化剂的比表面积增大,有利于提高其电催化活性.扫描电镜和透射电镜展示出Co0.85Se纳米片分散性较差,且团聚现象严重,而MWCNTs/Co0.85Se纳米复合催化剂显示Co0.85Se纳米片均匀分散在MWCNTs表面,且纳米片尺寸明显减小,有利于Co0.85Se纳米片暴露更多的活性位点.线性扫描伏安曲线测量表明,在酸性溶液中Co0.85Se纳米片在电流密度为10 mA cm?2时,其过电势为319 mV(vs.RHE),30 wt%MWCNTs/Co0.85Se的过电势为266 mV(vs.RHE).Co0.85Se和MWCNTs/Co0.85Se的Tafel斜率分别为92.6和60.5 mV dec?1.此外,MWCNTs/Co0.85Se的电流交换密度(j0)为0.07 mA cm?2.较小的Tafel斜率和高的电流交换密度表明,MWCNTs/Co0.85Se具有良好的反应动力学和快速的质子分离速率.交流阻抗谱表明MWCNTs/Co0.85Se比Co0.85Se电阻更小,电子传输速率更快.电化学活性表面积与双电层在固液界面处的电容测量值成正比.结果显示,30 wt%MWCNTs/Co0.85Se的双电层电容为0.22 mF cm^-2,高于Co0.85Se和15 wt%的rGO/Co0.85Se(0.04 mF cm^-2,0.17 mF cm^-2),这表明较大的电化学活性表面积有利于析氢反应进行.30 wt%MWCNTs/Co0.85Se的循环稳定测试表明其具有较好的稳定性.综上,本文介绍了通过一步水热法合成具有弱磁性的Co0.85Se和MWCNTs/Co0.85Se电催化剂,碳纳米管作为一种高导电性材料被引入Co0.85Se纳米片中以减少Co0.85Se的团聚,使Co0.85Se的活性位点增加,进而提高电催化制氢性能.     

Electrodeposited Pt-Ir electrodes: characterization and electrocatalytic activity for the reduction of the nitrate ion

The activity of Pt-Ir deposits on titanium for the reduction of the nitrate ion in 0.5 M perchloric acid was studied. The electrodes were characterized by SEM-EDAX, XPS and cyclic voltammetry. The activity of the electrodes for the nitrate reduction depended on the Pt-Ir ratio. Repetitive cyclic voltammograms produced an enrichment of the electrode surface with Ir and a decrease of the catalytic activity. A synergistic effect in the electrodes with low iridium content is discussed. Received: 2 June 1997 / Accepted: 28 August 1997     

Implanting Ni into N-doped puffed carbon: A new advanced electrocatalyst for oxygen evolution reaction

Tailored design and synthesis of high-quality electrocatalysts is vital for the advancement of oxygen evolution reaction (OER). Herein, we report a powerful puffing method to fabricate hierarchical porous N-doped carbon with numerous embedded Ni nanoparticles. Interestingly, during the puffing and annealing process, rice precursor with N and Ni sources can be in-situ converted into Ni-embedded N-doped porous carbon (N-PC/Ni) composite. The obtained N-PC/Ni composite possesses a cross-linked porous architecture containing conductive carbon backbone and active Ni nanoparticles electrocatalysts for OER. The pore formation in N-PC/Ni composite is also proposed because of carbothermic reduction. The N-PC/Ni composite is fully studied as electrocatalysts for OER. Due to increased active surface area, enhanced electronic conductivity and reactivity, the designed N-PC/Ni composite exhibits superior OER performance with a low Tafel slope (∼88 mV/dec) and a low overpotential as well as excellent long-term stability in alkaline solution. Our proposed rational design strategy may provide a new way to construct other advanced metal/heteroatom-doped composites for widespread application in electrocatalysis.     

Ionic liquid-functionalized graphene as modifier for electrochemical and electrocatalytic improvement: comparison of different carbon electrodes

Electrochemical activities of typically electrochemical targets at three kinds of modified carbon electrodes, i.e. carbon ionic liquid electrode (CILE), graphene/carbon paste electrode (CPE), and ionic liquid-functionalized graphene (IL-graphene)/CPE, were compared in detail. The redox processes of the probes at IL-graphene/CPE were faster than those at CILE and graphene/CPE from cyclic voltammetry. An electrochemical method for the simultaneous determination of guanine and adenine was described with detection limits of 6.5 × 10⁻⁸ mol L⁻¹ (guanine) and 3.2 × 10⁻⁸ mol L⁻¹ (adenine). Single A → G mutation of sequence-specific DNA could be discriminated by the IL-graphene/CPE.     

石墨化氮化碳负载Cu纳米颗粒用作高效氧还原电催化剂

高活性低成本氧还原反应(ORR)电催化剂是燃料电池和金属/空气电池等可再生能源技术的关键组成部分.在离子液体[(C16mim)2CuCl4]和质子化的石墨化氮化碳(g-CN)的存在下,采用简易的水热反应制备了Cu/g-CN电催化剂用于ORR.与纯的g-CN相比,所制Cu/g-CN表现出高的ORR催化活性:起始电势正移99 mV,为2倍动力学电流密度.另外,Cu/g-CN还表现出比商用Pt/C(HiSPECTM 3000,20%)催化剂更好的稳定性和甲醇容忍性.因此,该催化剂作为廉价的高效ORR电催化剂有望应用于燃料电池中.     

PtRu nanoparticles supported on 1-aminopyrene-functionalized multiwalled carbon nanotubes and their electrocatalytic activity for methanol oxidation

A new synthesis method for the preparation of high-performance PtRu electrocatalysts on multiwalled carbon nanotubes (MWCNTs) is reported. In this method, bimetallic PtRu electrocatalysts are deposited onto 1-aminopyrene (1-AP)-functionalized MWCNTs by a microwave-assisted polyol process. The noncovalent functionalization of MWCNTs by 1-AP is simple and can be carried out at room temperature without the use of expensive chemicals or corrosive acids, thus preserving the integrity and the electronic structure of MWCNTs. PtRu electrocatalysts on 1-AP-functionalized MWCNTs show much better distribution with no formation of aggregates, higher electrochemically active surface area, and higher electrocatalytic activity for the electrooxidation of methanol in direct methanol fuel cells as compared to that on conventional acid-treated MWCNTs and carbon black supported PtRu electrocatalysts. PtRu electrocatalysts on 1-AP-functionalized MWCNTs also show significantly enhanced stability.     

Facilitating a high‐performance photocatalyst for Suzuki reaction: Palladium nanoparticles immobilized on reduced graphene oxide‐doped graphitic carbon nitride

We prepared a non‐covalently coupled hybrid of reduced graphene oxide (rGO)‐doped graphitic carbon nitride (g‐C₃N₄) by freezing‐assisted assembly and calcination. Fourier transform infrared, Raman and X‐ray photoelectron spectroscopies and transmission electron microscopy confirmed that rGO was incorporated into the bulk g‐C₃N₄, which was an ideal support for loading Pd nanoparticles. The Pd nanoparticles with an average size of 4.57 nm were uniformly dispersed on the rGO‐doped g‐C₃N₄ surface. The layered structure provided large contact area of g‐C₃N₄ with rGO, further accelerating the electron transfer rate and inhibiting electron–hole recombination. Consequently, compared with Pd/rGO/g‐C₃N₄ and Pd/g‐C₃N₄, the Pd/rGO‐doped g‐C₃N₄ showed a prominent catalytic activity for visible‐light‐driven photocatalytic Suzuki–Miyaura coupling at ambient temperature. The Pd/rGO‐doped g‐C₃N₄ exhibited very high stability after six consecutive cycles with minimal loss of catalytic activity.     

Ag nanoparticles loaded on porous graphitic carbon nitride with enhanced photocatalytic activity for degradation of phenol

Highly efficient photocatalyst of visible-light-driven Ag nanoparticles loaded on porous graphitic carbon nitride (g-C₃N₄) was prepared by the reduction of Ag ions on porous g-C₃N₄. The obtained Ag/porous g-C₃N₄ composite products were characterized by X-ray diffraction (XRD), high resolution transmission electron microscopy (HRTEM), UV-vis diffuse reflection spectra (DRS), thermal gravimetric analysis (TGA). The results demonstrated that a homogeneous distribution of Ag NPs of 10 nm was attached onto the surface of the porous g-C₃N₄. The prepared Ag/porous g-C₃N₄ samples were applied for catalyzing the degradation of phenol in water under visible light irradiation. Porous g-C₃N₄ demonstrated an excellent support for the formation and dispersion of small uniform Ag NPs. When the weight percentage of Ag reaches 5%, the nanohybrid exhibits superior photocatalytic activities compared to bulk g-C₃N₄, porous g-C₃N₄, and 2% Ag/porous g-C₃N₄ hybrids. The enhanced photocatalytic performance is due to the synergic effect between Ag and porous g-C₃N₄, which suppressed the recombination of photogenerated electron-hole pairs.     

Enhanced electrocatalytic activity for H2O2 production by the oxygen reduction reaction: Rational control of the structure and composition of multi-walled carbon nanotubes

Hydrogen peroxide (H₂O₂) is a very useful chemical reagent, but the current industrial methods for its production suffer from serious energy consumption problems. Using high-activity and high-selectivity catalysts to electrocatalyze the oxygen reduction reaction (ORR) through a two-electron (2e^?) pathway is a very promising route to produce H₂O₂. In this work, we obtained partially oxidized multi-walled carbon nanotubes (MWCNTs) with controlled structure and composition by oxidation with concentrated sulfate and potassium permanganate at 40°C for 1 h (O-CNTs-40-1). The outer layers of O-CNTs-40-1 are damaged with defects and oxygen-containing functional groups, while the inner layers are maintained intact. The optimized structure and composition of the partially oxidized MWCNTs ensure that O-CNTs-40-1 possesses both a sufficient number of catalytic sites and good conductivity. The results of rotating ring disk electrode measurements reveal that, among all oxidized MWCNTs, O-CNTs-40-1 shows the greatest improvement in hydrogen peroxide selectivity (from ～ 30% to ～ 50%) and electron transfer number (from ～ 3.4 to ～ 3.0) compared to those of the raw MWCNTs. The results of electrochemical impedance spectroscopy measurements indicate that both the charge-transfer and intrinsic resistances of O-CNTs-40-1 are lower than those of the raw MWCNTs and of the other oxidized MWCNTs. Finally, direct tests of the H₂O₂ production confirm the greatly improved catalytic activity of O-CNTs-40-1 relative to that of the raw MWCNTs.     

NiSe2 nanoparticles embedded in CNT networks: Scalable synthesis and superior electrocatalytic activity for the hydrogen evolution reaction

For the first time, NiSe₂ nanoparticles embedded in CNT networks have been synthesized via spray-drying followed by a selenization process. The NiSe₂/CNTs hybrid (NCH) delivers superior electrocatalytic performance for HER. It has a low onset potential of ~ 159 mV and a cathode current density of 35.6 mA cm^− 2 at − 250 mV vs RHE; more importantly, the Tafel slope has a very low value of 29 mV dec^− 1, which is comparable to a platinum (Pt) catalyst; in addition, it is stable even after 1000 cycles. The superior HER performance of NCH is attributed to its unique structure, which is composed of ultrathin NiSe₂ nanoparticles homogenously embedded in highly conductive and porous CNT networks. This not only provides abundant HER active sites, but also guarantees robust contact between the NiSe₂ nanoparticles and the CNT networks. The present study provides new insights into the large-scale and low-cost synthesis of a highly effective and stable NiSe₂-based electrocatalyst which could be extended to large-scale production of other non-precious metal hybrid catalysts with low cost, high efficiency and excellent stability.     

H2S预处理对Ni2P/SiO2催化剂结构及氯苯加氢脱氯性能的影响

采用10% H₂S/H₂对Ni₂P/SiO₂催化剂进行预处理,利用X射线衍射、电感耦合等离子发射光谱、X射线光电子能谱、CO化学吸附、H₂程序升温脱附、NH₃程序升温脱附及活性评价等方法研究了H₂S预处理对催化剂结构和氯苯加氢脱氯反应性能的影响.结果表明,即使在873K进行H₂S预处理,Ni₂P/SiO₂催化剂体相结构及Ni₂P晶粒大小没有发生变化,但导致Ni₂P晶粒表面形成了磷硫镍相(NiP_xS_y),同时使表面溢流氢数量增加.硫物种的存在不仅阻塞了部分镍中心,使催化剂表面镍中心密度降低,也导致镍中心的缺电子性进一步增加.经H₂S预处理后Ni₂P/SiO₂催化剂上氯苯加氢脱氯反应的转化频率(TOF)明显提高,这可能与催化剂表面Ni物种的缺电子性增强及溢流氢数量增多有关.     

Pt nanoparticles supported on non-carbon titanium chromium nitride nanotubes with high activity and durability for methanol oxidation reaction

Journal of Solid State Electrochemistry - A hybrid titanium chromium nitride nanotube (Ti0.95Cr0.05N NT) support was prepared by a facile synthesis procedure and further used as support for Pt...     

Multilayer films of carbon nanotubes and redox polymer on screen-printed carbon electrodes for electrocatalysis of ascorbic acid

Multilayer films containing multiwall carbon nanotubes and redox polymer were successfully fabricated on a screen-printed carbon electrode using layer-by-layer (LBL) assembled method. UV-vis spectroscopy, X-ray photoelectron spectroscopy, field-emission scanning electron microscopy and electrochemical method were used to characterize the assembled multilayer films. The multilayer films modified electrodes exhibited good electrocatalytic activity towards the oxidation of ascorbic acid (AA). Compared with the bare electrode, the oxidation peak potential negatively shifted about 350 mV (versus Ag/AgCl). Furthermore, the modified screen-printed carbon electrodes (SPCEs) could be used for the determination of ascorbic acid in real samples.     

Synthesis of graphitic carbon nitride through pyrolysis of melamine and its electrocatalysis for oxygen reduction reaction

Graphitic carbon nitride（g-C₃N₄） was synthesized via direct pyrolysis of melamine and its electrocatalysis toward oxygen reduction reaction was studied.The morphology and structures of the products were characterized by scanning electron microscope and X-ray powder diffractometer.It was found that higher pyrolysis temperature resulted in more perfect crystalline structure of the graphitic carbon nitride product.Electrochemical characterizations show that the g-C₃N₄ has electrocatalytic activity toward ORR through a two-step and two-electron process.